微乳法制备Au/Al2 O3 催化剂及其催化氧化CO性能的研究

用Tx-100／正己醇／环己烷／水的W／O微乳体系，合成了一系列Au／Al2O3催化剂。考察了焙烧温度、沉淀剂种类、搅拌方式等对Au／Al2O3，催化氧化CO活性的影响。结果表明：以氨水为沉淀剂，机械搅拌，600℃焙烧制得的Au／Al2O3，显示出较好的CO氧化性能。当反应温度为100℃时，CO转化率达85．0％，240℃时转化率达96．0％。XRD，DTA，TPR和TEM等表征表明：低温焙烧的催化剂，大部分载体Al2O3为无定型，对催化活性不利；焙烧温度过高，可能造成金微粒的团聚烧结，使其活性下降；由较强烈的搅拌方式制得的Au／Al2O3经适宜温度焙烧，可获得金粒尺寸较小、CO催化氧化活性较高的Au／γ-Al2O3催化剂。     

丙烯气相直接环氧化Au/TiO2催化剂的研究

在H2和O2共存条件下，金催化剂催化丙烯气相直接环氧化反应是近年来发展起来的一种新型环氧丙烷(PO)合成技术．本文采用沉积沉淀法制备了一系列Au／TiO2催化剂，考察了反应溶液的pH值、Au负载量、沉淀剂以及焙烧温度等因素对催化剂丙烯环氧化催化性能的影响．结果表明制备条件对催化性能有明显影响：反应溶液的pH值为7．5及Au负载量为2．4％时所得催化剂活性最好；当以Na2CO3、NaOH等含Na^ 物质作为沉淀剂时，催化性能明显优于Li^ 、K^ 等其它碱金属离子；400℃焙烧制得的催化剂活性较好，在50℃低温反应条件下，环氧丙烷得率可达1．3％．HRTEM结果表明，催化剂中Au组分高度分散于载体表面，且随着焙烧温度的增加Au粒因发生聚集而变大，从而影响了催化剂的活性．表面XPS分析证实，活性较好的Au／TiO2催化剂中活性组分Au除部分呈氧化态外，主要是以金属态的形式存在．     

钴氧化物负载的纳米金催化剂的制备及其性能研究

采用共沉淀法和金属有机配合物固载法，分别制备了钴氧化物负载的纳米金催化剂．考察了该催化剂对CO低温氧化反应的催化活性及其制备方法和制备条件，如焙烧温度和时间、金的负载量、活性组分前体、沉淀剂的滴加顺序等因素对催化性能的影响．结果表明：严格控制制备条件．上述两种方法制备的3％Au／Co3O4催化剂，对CO氧化反应都具有很高的催化活性，可分别于-22℃和-5℃将空气中1％的CO完全转化为CO2．：XRD和TEM测试结果显示．催化剂上的金颗粒大小在10nm范围内，载体为适度结晶的四氧化三钴．     

新型磁性纳米固体酸催化剂ZrO2/Fe3O4的制备及表征

根据将磁性一材料和固体酸进行组装的设想，成功制备了磁性纳米固体酸催化剂。纳米级样性前体-磁基体(Fe3O4)的磁性、粒子尺寸受到Fe^2^+/Fe^3^+投料比和用于沉淀的NaOH浓度的显著影响；不同复合方法也对磁性固体酸催化剂ZrO2/Fe3O4的酯化催化性能影响显著。XRD，XPS，TEM，比表面积测定，元素组成分析及磁学性能测定等表征结果证实，新型催化剂以磁性材料为核，固体酸催化剂活性组分包覆在其外部形成包覆型的磁性纳米催化剂。该系列催化剂均具有较小的粒子尺寸、较强的磁性及较高的酯化催化活性；并且易于通过磁场进行回收，使用寿命较长。它们对乙酸与正丁醇酯化反应的催化活性随着ZrO2含量增加而提高。催化剂中ZrO2的晶化温度因为Fe3O4的存在而升高，有利于催化剂活性的保持，热处理温度会对催化剂的磁性及催化活性产生影响。     

Au／Fe2O3／Al2O3催化剂上丙烯选择催化还原NO

以浸渍法制备的Fe2O3/γ-Al2O3为载体,采用均相沉积沉淀方法制备了Au/Fe2O3/Al2O3催化剂.该催化剂在丙烯选择催化还原NO反应中显示出很好的低温催化活性,300℃时NO被选择还原为N2的转化率可达43%,而在Au/Al2O3催化剂上,NO的转化率仅为21%.水蒸气的加入对催化剂活性的影响较小.X射线衍射结果表明,Au和Fe2O3高度分散在Al2O3载体上.吸附氢气的程序升温还原结果表明,Au与Fe2O3之间存在着强相互作用,Au的存在促进了Fe2O3的还原,Au和Fe2O3之间的协同作用可能是Au/Fe2O3/Al2O3催化剂在丙烯选择还原NO反应中具有较高低温催化活性的原因之一.     

Au/CeO2/Y和Au-MFe2O4催化剂用于有氧条件下CH4还原NOx的研究

以CeO2／Y分子筛和MFe2O4(M=Ni,Co，Zn)为载体，制备Au／CeO2／Y和Au-MFe2O4负载型金催化剂．用CH4做还原剂，考察了它们在有氧条件下催化还原NOχ的活性．结果表明：在Au-Y中引人助剂Ce，使得Au／CeO2／Y的催化活性高于Au／Y；Au-CoFe2O4的催化活性高于Au-Fe2O3，反应温度为300℃时，NOχ在Au-CoFe2O4上的转化率达到39．70%．     

微乳法制备Au／Fe2O3水煤气变换反应催化剂 Ⅰ．制备参数对催化剂活性的影响

 分别在TritonX－100／正己醇／环己烷／水和十六烷基三甲基溴化铵（CTAB）／正己醇／水的W／O型微乳液体系中合成了Au／Fe2O3催化剂，考察了主要制备参数对催化剂水煤气变换活性的影响．结果表明，催化剂的焙烧温度、水与表面活性剂的质量比（rw）、表面活性剂浓度（W）、表面活性剂种类及催化剂活性组分金的负载量均对催化剂活性有显著的影响．催化剂的最佳焙烧温度为250℃，催化活性随着rw和W的增加而降低，由TritonX－100制得的催化剂的活性高于由CTAB制得的催化剂．当金负载量为3％，水煤气变换反应温度为200℃时，CO的转化率可达99．5％．     

沉淀剂种类对水煤气变换Au/Fe2O3催化剂结构和催化性能的影响

 采用7种沉淀剂(K2CO3, Na2CO3, NH4OH, (NH4)2CO3, NaOH, KOH和尿素)通过共沉淀法制备了低温水煤气变换(WGS) Au/Fe2O3催化剂,考察了沉淀剂种类对其催化性能的影响. 通过N2吸附, X射线荧光光谱、 X射线衍射、 H2程序升温还原和CO程序升温脱附等表征手段,探讨了不同沉淀剂影响Au/Fe2O3催化剂WGS性能的原因. 结果表明,采用K2CO3和Na2CO3制备的催化剂样品在200 ℃以上具有较好的活性和稳定性,其中K2CO3是最佳沉淀剂. 而采用NH4OH和(NH4)2CO3制备的样品的催化活性相对较低,在200 ℃达到峰值. 由其它3种沉淀剂制备的样品的催化活性都较差, CO转化率最高只有35%. 沉淀剂种类不仅明显地影响金离子和铁离子的共沉淀,而且会明显地影响共沉淀物在后续焙烧过程中的结晶行为. 前者将影响金的负载量,后者则影响金粒子的分散度以及氧化铁载体的还原性质和对CO的吸脱附性能. Au/Fe2O3催化剂的低温高活性及其稳定性归因于高度分散的金粒子及其与易被还原的氧化铁载体间的协同作用. 催化剂中金负载量增大、金粒子分散度提高以及氧化铁晶粒减小均有利于其催化性能的提高.     

Cr2O3-Co3O4／SiO2对十八醇氧化生成十八酸反应的催化性能

 制备了一系列不同Cr／Co比例的Cr2O3－Co3O4／SiO2催化剂，并用XRD，FT－IR和BET等手段对催化剂进行了表征；考察了催化剂对十八醇氧化生成十八酸反应的催化性能，及反应条件（反应温度和反应时间）对催化性能的影响，确定了最佳反应条件．结果表明，金属硝酸盐在773K焙烧后转变成相应的氧化物并负载于二氧化硅上．Cr2O3－Co3O4／SiO2催化剂对十八醇氧化反应有很高的催化活性，十八酸选择性最高可达99．93％，收率可达52．44％．Cr2O3－Co3O4／SiO2催化剂的活性明显高于单一的Cr2O3／SiO2或Co3O4／SiO2催化剂     

Co/γ-Al2O3催化剂上CO氧化反应的研究

以浸渍法与沉积沉淀法制备了不同Co负载量的Co／γ-Al2O3催化剂，研究了对CO的催化氧化行为,考察了Co含量，焙烧温度，反应温度等对催化剂氧化性能的影响，结果表明，沉积沉淀法制备400℃焙烧的负载量为10％的Co／γ-Al2O3在90℃就能够实现CO完全氧化，且热稳定性比浸渍法制得催化剂好．本文还采用XRD、TPR、XPS等技术，分别研究了Co／γ-Al2O3样品的晶相结构，还原性能及表面化学状态.XRD结果表明，以硝酸盐为前驱物的Co负载于γ-Al2O3后，Co主要以Co3O4结构存在，反应的活性相Co3O4的生成有利于CO催化氧化，且以不同制备方法得到的样品中Co3O4晶粒大小不同，催化活性也不同．TPR结果表明，以沉积沉淀法制备催化剂的还原峰向低温移动，CoOx的还原更加容易．XPS表面分析表明沉淀法制备的Co／γ-Al2O3样品中，Co3O4在载体表面富集．     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

化学计量中不确定度评定研究进展

测量不确定度是表征合理地赋予被测量之值的分散性的参数。本文针对化学计量不确定度评定基础模型仅适用于线性模型、概率分布为正态分布或缩放位移t分布等局限,介绍了近年来不确定度评定的研究热点:蒙特卡罗方法(Monte Carlo Method,MCM),不确定度评定的来源、评定概念、评估方法及其发展过程,扩大了测量不确定度评定与表示的适用范围。     

微量钙的测定方法研究进展

介绍了1995-2006年期间测定微量和痕量钙的方法,如电感耦合等离子体-原子发射光谱法、原子吸收光谱法以及离子色谱法等的工作原理和特点,并说明了其测定微量钙的应用领域。并对微量钙的测定技术进行了展望(引用文献55篇)。