Electrodeposition and characterization of Cu-TiO2 nanocomposite coatings

Cu-TiO₂ nanocomposites were prepared by electrodeposition method onto copper substrate using an acid copper plating bath containing dispersed nanosized TiO₂. The composition of codeposited TiO₂ nanoparticles in the composite coatings was controlled by the addition of different concentrations of TiO₂ nanoparticles in the bath solution. The average crystallite size was calculated by using X-ray diffraction analysis and it was ~32 nm for electrodeposited copper and ~33 nm for Cu-TiO₂ composite coatings. The crystallite structure was fcc for electrodeposited copper and Cu-TiO₂ nanocomposite coatings. The surface morphology and composition of the nanocomposites were examined by scanning electron microscopy and energy dispersive X-ray spectroscopy analysis. The effect of TiO₂ content on the corrosion and wear resistance properties of the nanocomposite coatings was also presented. The codeposited TiO₂ nanoparticles in the deposit increased the corrosion and wear resistance, which were closely related with TiO₂ content in the nanocomposites. The wear resistance and microhardness of the Cu-TiO₂ nanocomposite coatings were higher than electrodeposited copper. The corrosion resistance property of the electrodeposited copper and Cu-TiO₂ nanocomposite coatings was evaluated by electrochemical impedance and Tafel polarization studies. Cu-TiO₂ composite coatings were more corrosion resistant than electrodeposited copper.     

Inclusion of W in electroless Ni–B coating developed from a stabilizer free bath and investigation of its tribological behaviour

In the present study, tribological and corrosion behaviour of electroless Ni–B–W (ENB-W) coatings prepared from stabilizer-free baths and deposited on AISI 1040 steel substrates were examined. Three distinct coating bath temperatures (85 °C, 90 °C, and 95 °C) were varied for coating deposition. The coatings showed nodular morphology. Thermogravimetric study of ENB-W coatings revealed improved thermal stability attained at 95 °C bath temperature. The microhardness of ENB-W coating was 645, 690, and 720 HV₁₀₀ at bath temperatures of 85 °C, 90 °C, and 95 °C respectively. The inclusion of W to Ni–B coating enhanced the hardness by ∼150 HV₁₀₀. On a pin-on-disc tribometer, wear test was conducted. The precipitation of Ni (111) and its borides occurred post sliding wear at high temperatures (300 °C). Ni (111) crystallite size decreased because of high temperature sliding wear at 300 °C with an increase in coating bath temperature. With a reduction in crystallite size at high temperatures, both wear rate and COF decreases. The scratch hardness and first critical load of failure of the coatings was determined using a scratch tester. Using potentiodynamic polarization, corrosion resistance of ENB-W coatings in 3.5% NaCl was investigated. ENB-W coatings could provide shielding to AISI 1040 steel from corrosion. Though the corrosion resistance is poor with respect to lead stabilized coatings.     

Zn–HA–TiO2 nanocomposite coatings electrodeposited on a NiTi shape memory alloy

In this work, zinc–hydroxyapatite (Zn–HA) and zinc–hydroxyapatite–titania (Zn–HA–TiO₂) nanocomposite coatings were electrodeposited onto a NiTi shape memory alloy, using a chloride zinc plating bath. The structure of the composite coatings was characterized by X‐ray diffraction, scanning electron microscopy and high‐resolution transmission electron microscopy. According to the results, the Zn–HA–TiO₂ coating exhibited a plate‐like surface morphology, where the addition of the nanoparticles caused to an increase in roughness. It was also found that due to applying a proper stirring procedure during co‐deposition, a homogenous dispersion of the nanoparticles in the coatings was achieved. Also, the addition of the TiO₂ nanoparticles to the Zn–HA–TiO₂ coating enhanced the microhardness and wear resistance. Copyright © 2014 John Wiley & Sons, Ltd.     

Prefabrication of two-dimensional Ni–W/TiN films on oil-gas X52 steels by pulse electrodeposition

The main aim of this investigation was to prefabricate two-dimensional Ni–W/TiN films on oil-gas X52 steel substrates via pulse electrodeposition (PE). The influences of the TiN content in the bath on the surface morphology, nano-hardness, wear, and corrosion properties of the films were also discussed. The results indicated that the TiN particle size was only ～33 nm in 8 g/L TiN electrolyte, which was ～2.4 times less than that of TiN in 16 g/L solution. The Ni–W/8TiN film exhibited a uniform, smooth surface, and the depression depth and protrusion height were 45.3 nm and 81.7 nm, respectively. Three diffraction peaks at 43.72, 50.78, and 75.26° in the Ni–W/4TiN film emerged as the sharpest and narrowest peaks among the four films. Three XPS peaks for the Ni 2p_3/2 were present at 852.13, 856.35, and 861.87 eV in the Ni–W/8TiN film, corresponding to Ni, Ni²⁺ (Ni(OH)₂), Ni³⁺ (NiOOH) species. Besides, the XPS peak of W 4f_7/2, which located at 33.85 eV belonged to elemental W. The Ni–W/8TiN film had the lowest wear depth and width at 32.1 μm and 5.7 mm, respectively. Only some narrow and shallow scratches were found on the Ni–W/8TiN film surface, showing its outstanding tribological properties among the films tested. In addition, the Ni–W/4TiN film showed the highest mean frictional coefficient of 0.73, which was ～1.6 times more than that of the Ni–W/8TiN film.     

Optical and electrical conducting properties of Polyaniline/Tin oxide nanocomposite

Polyaniline(PANI)/Tin oxide (SnO₂) hybrid nanocomposite with a diameter 20–30 nm was prepared by co-precipitation process of SnO₂ through in situ chemical polymerization of aniline using ammonium persulphate as an oxidizing agent. The resulting nanocomposite material was characterized by different techniques, such as X-ray diffraction (XRD), Transmission Electron Microscopy (TEM), Fourier Transform Infrared spectroscopy (FT-IR) and Ultraviolet–Visible spectroscopy (UV–Vis), which offered the information about the chemical structure of polymer, whereas electron microscopy images provided information regarding the morphology of the nanocomposite materials and the distribution of the metal particles in the nanocomposite material. SEM observation showed that the prepared SnO₂ nanoparticles were uniformly dispersed and highly stabilized throughout the macromolecular chain that formed a uniform metal-polymer nanocomposite material. UV–Vis absorption spectra of PANI/SnO₂ nanocomposites were studied to explore the optical behavior after doping of nanoparticles into PANI matrix. The incorporation of SnO₂ nanoparticles gives rise to the red shift of π–π¹ transition of polyaniline. Thermal stability of PANI and PANI/SnO₂ nanocomposite was investigated by thermogravimetric analysis (TGA). PANI/SnO₂ nanocomposite observed maximum conductivity (6.4 × 10^?3 scm^?1) was found 9 wt% loading of PANI in SnO₂.     

High reversible capacity and rate capability of ZnCo2O4/graphene nanocomposite anode for high performance lithium ion batteries

A facile and straightforward method was adopted to synthesize ZnCo₂O₄/graphene nanocomposite anode. In the first step, pure ZnCo₂O₄ nanoparticles were synthesized using urea-assisted auto-combustion synthesis followed by annealing at a low temperature of 400 °C. In the second step, in order to synthesize ZnCo₂O₄/graphene nanocomposite, the obtained pure ZnCo₂O₄ nanoparticles were milled with 10 wt% reduced graphene nanosheets using high energy spex mill for 30 s. The ZnCo₂O₄ nanoparticles, with particle sizes of 25–50 nm, were uniformly dispersed and anchored on the reduced graphene nanosheets. Compared with pure ZnCo₂O₄ nanoparticles anode, significant improvements in the electrochemical performance of the nanocomposite anode were obtained. The resulting nanocomposite delivered a reversible capacity of 1124.8 mAh g⁻¹ at 0.1 C after 90 cycles with 98% Coulombic efficiency and high rate capability of 515.9 mAh g⁻¹ at 4.5 C, thus exhibiting one of the best lithium storage properties among the reported ZnCo₂O₄ anodes. The significant enhancement of the electrochemical performance of the nanocomposite anode could be credited to the strong synergy between ZnCo₂O₄ and graphene nanosheets, which maintain excellent electronic contact and accommodate the large volume changes during the lithiation/delithiation process.     

Effect of SiC/nano‐CeO2 on wear resistance and microstructures of Ti3Al/γ‐Ni matrix laser‐cladded composite coating on Ti–6Al–4V alloy

The Ti–6Al–4V alloy is an important aviation material, but has a poor resistance to slide wear. Laser cladding of the Al₃Ti + Ni/Cr/C + TiB₂/Al₂O₃ + SiC/nano‐CeO₂ preplaced powders on the Ti–6Al–4V alloy can form the Ti₃Al/γ‐Ni matrix composite coating, which improves the wear resistance of the substrate. In this study, the Al₃Ti + Ni/Cr/C + TiB₂/Al₂O₃ + SiC/nano‐CeO₂ laser‐cladded coating was researched by means of X‐ray diffraction, scanning electron microscopy, and energy dispersive spectrometry. The experimental results indicate that under the action of SiC/nano‐CeO₂, this composite coating exhibited a fine microstructure. Furthermore, the proper content of nano‐CeO₂ decreased the crack tendency. The results above indicated that, it is feasible to improve the tribological property of the Al₃Ti + Ni/Cr/C + TiB₂/Al₂O₃ laser‐cladded coating by adding of SiC/nano‐CeO₂. Copyright © 2011 John Wiley & Sons, Ltd.     

Electrocatalytic oxidation of nitric oxide at TiO2–Au nanocomposite film electrodes

Structured films of TiO₂ (anatase) nanoparticles (ca. 6 nm diameter) and gold nanoparticles (nominal 20 nm diameter) are formed via a layer-by-layer deposition procedure. TiO₂ nanoparticles are deposited with a Nafion polyelectrolyte binder followed by calcination to give a mesoporous thin film electrode. Gold nanoparticles are incorporated into this film employing a poly(diallyldimethylammonium chloride) polyelectrolyte binder followed by calcination to give a stable mesoporous TiO₂–gold nanocomposite. This methodology allows well-defined and structured films to be formed which are re-usable after a 500 °C heat treatment in air.Electrochemical experiments are performed in aqueous KCl and buffer solutions and for the oxidation of nitric oxide, NO, and nitrite in phosphate buffer solution. It is shown that the NO oxidation occurs as a highly effective electrocatalytically amplified process at the surface of the gold nanocomposite probably with co-evolution of oxygen, O₂. In contrast, the oxidation of nitrite to nitrate occurs at the same potential but without oxygen evolution. A mechanistic scheme for the amplified NO detection process is proposed.     

Development of multifunctional polydimethylsiloxane (PDMS)‐epoxy‐zinc oxide nanocomposite coatings for marine applications

Multifunctional epoxy‐polydimethylsiloxane nanocomposite coatings with antifouling and anticorrosion characteristics have been developed via in situ polymerization method at different loading (1, 3, and 6.5 wt.%) of ZnO nanoparticles to cater marine applications. A detailed comparative analysis has been carried out between epoxy‐polydimethylsiloxane control (EPC) and ZnO‐reinforced coatings to determine the influence of ZnO loading on various properties. The incorporation of ZnO in EPC led to increase in root mean square (RMS) roughness to 126.75 nm and improved hydrophobicity showing maximum contact angle of 123.5° with low surface energy of 19.75 mN/m of nanocomposite coating as compared with control coating. The differential scanning calorimetry (DSC) result indicated improved glass transition temperature of nanocomposite coatings with highest T_g obtained at 83.69°C in case of 1 wt.% loading of ZnO. The increase in hydrophobicity of the system was accompanied by upgraded anticorrosion performance exhibiting 98.8% corrosion inhibition efficiency (CIE) as compared with control coating and lower corrosion rate of 0.12 × 10^?3 mm/year. The Taber abrasion resistance and pull‐off adhesion strength results indicated an increment of 34.7% and 150.7%, respectively, in case of nanocomposite coating as compared with the control coating. The hardness of nanocomposite coatings was also improved, and maximum hardness was found to be 65.75 MPa for nanocomposite coating with 1 wt.% of ZnO. Our study showed that the nanocomposite coating was efficient in inhibiting accumulation of marine bacteria and preventing biofouling for more than 8 months. The developed environment‐friendly and efficient nanocomposite material has a promising future as a high‐performance anticorrosive and antifouling coating for marine applications.     

Fabrication and photoluminescence properties of Ag0 and Ag0–Er3+ containing plasmonic glass nanocomposites in the K2O–ZnO–SiO2 system

Here, we report the preparation of nano silver (Ag) and nano Ag-erbium (Ag–Er) co-embedded potassium–zinc-silicate based monolithic glass nanocomposites by a controlled heat-treatment process of precursor glasses. The nanocomposites were characterized by differential scanning calorimeter, dilatometer, UV–Visible absorption spectrophotometer, X-ray diffractometer and transmission electron microscope and spectroflurimeter. A strong surface plasmon resonance (SPR) band is observed around 430 nm in all the heat-treated glass nanocomposite samples due to the formation of Ag⁰ nanoparticles (NP). The Ag-glass nanocomposite samples display nearly 2-fold enhanced photoluminescence (PL) at 470 nm upon excitation at 290 nm until the size of the NP increases to the value equals to the mean free path of conduction electrons inside the particles. On contrary to this, the photoluminescence spectra of Er³⁺ ions exhibit a gradual decrease of NIR emission at 1540 nm due to ⁴I_13/2 → ⁴I_15/2 transition under excitation at 523 nm in the heat-treated glass nanocomposites which happened due to excitation energy transfer of Er³⁺ ions to the Ag NP, acting as ‘plasmonics diluents’ for Er³⁺ ions. These nanocomposites have huge potential for various nanophotonic applications.     

In–CuInS2 nanocomposite film prepared by pulsed laser deposition using a single source precursor

An In–CuInS₂ nanocomposite film has been prepared by Pulsed Laser Deposition applying a single source precursor. X-ray powder diffraction, Raman spectroscopy and transmission electron microscopy observations evidence that the film consists of nanocrystals of elemental In and chalcopyrite type CuInS₂ with sizes of 36 and 17 nm respectively. A detailed analysis of the electrical performance of the film suggests that the nanoparticles are in Ohmic contact and that the resistivity is mainly caused by the CuInS₂ nanocrystals which are less conducting than the pure In metal. Irradiation of the film with light shows a photoconductive effect mainly with wavelengths larger than 515 nm and smaller than 850 nm.     

Self-assembled Nafion–silica nanoparticles for elevated-high temperature polymer electrolyte membrane fuel cells

In this paper, a novel Nafion/SiO₂ nanocomposite membrane based on the self-assembled Nafion–SiO₂ nanoparticles was developed. The average particle size of Nafion–SiO₂ nanoparticles prepared by self-assembly process was 2.8 ± 0.5 nm. The self-assembled Nafion–SiO₂ nanoparticles significantly enhance the durability of the Nafion/silica nanocomposite membrane as compared to that of conventional Nafion/silica composite and Nafion 212 membranes under wet/dry cyclic tests at 90 °C. With an addition of 5 wt% self-assembled Nafion–SiO₂ nanoparticles, the Nafion/SiO₂ nanocomposite membrane shows a significantly improved performance stability at cell/humidifying temperatures of 100 °C/60 °C under a current density of 600 mA/cm², and the degradation rate is 0.12 mV/min, almost 20 times lower than 2.33 mV/min measured on the pristine Nafion 212 membrane under the same conditions. The present results demonstrate the promises of the self-assembled Nafion/SiO₂ nanocomposite membrane for elevated-high temperature PEM fuel cells applications.     

Preparation and photocatalytic activity of TiO<Subscript>2</Subscript> films with Ni nanoparticles

Titania thin films were synthesized by sol–gel dip-coating method with metallic Ni nanoparticles synthesized separately from an organometallic precursor Ni(COD)₂ (COD = cycloocta-1,5-diene) in presence of 1,3-diaminopropane as a stabilizer. Titania was obtained from a titanium isopropoxide precursor solution in presence of acetic acid. A Ni/TiO₂ sol system was used to coat glass substrate spheres (6, 4 and 3 mm diameter sizes), and further heat treatment at 400 °C was carried out to promote the crystallization of titania. XRD analysis of the TiO₂ films revealed the crystallization of the anatase phase. Transmission Electron Microscopy (TEM) and High Resolution TEM studies of Ni nanoparticles before mixing with the TiO₂ solution revealed the formation of Ni nanostructures with an average size of 5–10 nm. High-angle annular dark-field images of the Ni/TiO₂ system revealed well-dispersed Ni nanoparticles supported on TiO₂ and confirmed by AFM analysis. The photocatalytic activity of the Ni/TiO₂ films was evaluated in hydrogen evolution from the decomposition of ethanol using a mercury lamp for UV light irradiation. Titania films in presence of Ni nanoparticles show higher efficiency in their photocatalytic properties in comparison with TiO₂.     

Synthesis and characterization of Si-Zr-Mo nanocomposite as a rapid and efficient catalyst for aromatization of Hantzsch 1,4-dihydropyridines

Nanocomposite of Silica-zirconia-molybdate designated as Si-Zr-Mo was prepared via the reaction of the in situ generated zirconium-tetra octanoxide [Zr(Oct)₄] through condensation of zirconium-tetra-n-butoxide and 1-octanol in a sol–gel method with sulfuric acid and tetraethylorthosilicate (TEOS) followed by grafting of MoO₄^2? on modified silico zirconia nanocomposite under reflux conditions. The prepared nanocomposite was characterized using inductively coupled plasma (ICP), N₂ sorption isotherms, transmission electron microscopy (TEM), and FT-IR spectroscopy. The as prepared nanocomposite had a surface area and pore dimension of 140 m²/g and 1.48 nm, respectively. The morphology of sulphated silico zirconia nanocomposite after immobilization MoO₄^2? has been changed from nanoparticles to nanaorods. It was found that the synthesized nanocomposite successfully catalyze the oxidative dehydrogenation of 1,4-dihydropyridines (1,4-DHPs) with 92–100% conversion and 80–100% selectivity toward the desired products.     

In Situ Confined Growth Based on a Self‐Templating Reduction Strategy of Highly Dispersed Ni Nanoparticles in Hierarchical Yolk–Shell Fe@SiO2 Structures as Efficient Catalysts

Ni‐based magnetic catalysts exhibit moderate activity, low cost, and magnetic reusability in hydrogenation reactions. However, Ni nanoparticles anchored on magnetic supports commonly suffer from undesirable agglomeration during catalytic reactions due to the relatively weak affinity of the magnetic support for the Ni nanoparticles. A hierarchical yolk–shell Fe@SiO₂/Ni catalyst, with an inner movable Fe core and an ultrathin SiO₂/Ni shell composed of nanosheets, was synthesized in a self‐templating reduction strategy with a hierarchical yolk–shell Fe₃O₄@nickel silicate nanocomposite as the precursor. The spatial confinement of highly dispersed Ni nanoparticles with a mean size of 4 nm within ultrathin SiO₂ nanosheets with a thickness of 2.6 nm not only prevented their agglomeration during catalytic transformations but also exposed the abundant active Ni sites to reactants. Moreover, the large inner cavities and interlayer spaces between the assembled ultrathin SiO₂/Ni nanosheets provided suitable mesoporous channels for diffusion of the reactants towards the active sites. As expected, the Fe@SiO₂/Ni catalyst displayed high activity, high stability, and magnetic recoverability for the reduction of nitroaromatic compounds. In particular, the Ni‐based catalyst in the conversion of 4‐nitroamine maintained a rate of over 98 % and preserved the initial yolk–shell structure without any obvious aggregation of Ni nanoparticles after ten catalytic cycles, which confirmed the high structural stability of the Ni‐based catalyst.     

苯部分加氢制环己烯新型Ru-B/MOF催化剂

制备了多种金属-有机骨架(MOF)材料,采用浸渍-化学还原法制备了非晶态Ru-B/MOF催化剂,考察了它们在苯部分加氢反应中的催化性能.催化性能评价结果表明,这些催化剂的初始反应速率(r0)顺序为Ru-B/MIL-53(Al)Ru-B/MIL-53(Al)-NH2Ru-B/UIO-66(Zr)Ru-B/UIO-66(Zr)-NH2Ru-B/MIL-53(Cr)Ru-B/MIL-101(Cr)Ru-B/MIL-100(Fe),环己烯初始选择性(S0)顺序为Ru-B/MIL-53(Al)≈Ru-B/MIL-53(Cr)Ru-B/UIO-66(Zr)-NH2Ru-B/MIL-101(Cr)Ru-B/MIL-53(Al)-NH2Ru-B/UIO-66(Zr)≈Ru-B/MIL-100(Fe).催化性能最好的Ru-B/MIL-53(Al)催化剂上的r0和S0分别为23 mmol·min-1·g-1和72%.采用多种手段,对催化性能差异最为显著的Ru-B/MIL-53(Al)和Ru-B/MIL-100(Fe)催化剂的物理化学性质进行了表征.发现MIL-53(Al)载体能够更好地分散Ru-B纳米粒子,粒子的平均尺寸为3.2 nm,而MIL-100(Fe)载体上Ru-B纳米粒子团聚严重,粒径达46.6 nm.更小的粒径不仅能够提供更多的活性位,而且也有利于环己烯选择性的提高.对Ru-B/MIL-53(Al)催化剂的反应条件进行了优化,在180°C和5 MPa的H2压力下,环己烯得率可达24%,展示了MOF材料用作苯部分加氢催化剂载体的良好前景.     

Effect of Cu in electroless Ni–Cu–P coating on passivation process

Electroless Ni–P and Ni–Cu–P coatings were passivated by chromate conversion treatment respectively. The anticorrosive performances of passivated coatings were investigated by potentiodynamic polarization and electrochemical impedance spectroscopy measurements. The passivated Ni–Cu–P coating exhibited a high corrosion resistance with the i_corr of 0.236 μA/cm,² while the value of passivated Ni–P coating was only 1.030 μA/cm,² indicating the passive film could improve the corrosion resistance of Ni–Cu–P coating to a significant extent. High‐resolution X‐ray photoelectron spectroscopy was used to determine the chemical states of elements detected in the passive film. Compared with passivated Ni–P coating, the passive film on Ni–Cu–P coating exhibited a higher ratio of Cr₂O₃ to Cr(OH)₃ with the value of 72:28, which was the main factor for passivated Ni–Cu–P coating showing excellent corrosion resistance. The effect of Cu in electroless Ni–Cu–P coating on passivation process was discussed by the contrast experiment. Copyright © 2016 John Wiley & Sons, Ltd.     

Pure CuCr2O4 nanoparticles: Synthesis,characterization and their morphological and size effects on the catalytic thermal decomposition of ammonium perchlorate

In the present paper a pure phase of the copper chromite spinel nanoparticles (CuCr₂O₄ SNPs) were synthesized via the sol–gel route using citric acid as a complexing agent. Then, the CuCr₂O₄ SNPs has been characterized by field emission scanning electron microscope (FE-SEM), transmission electron microscopy (TEM), and X-ray diffraction (XRD). In the next step, with the addition of Cu–Cr–O nanoparticles (NPs), the effects of different parameters such as Cu–Cr–O particle size and the Cu/Cr molar ratios on the thermal behavior of Cu–Cr–O NPs + AP (ammonium perchlorate) mixtures were investigated. As such, the catalytic effect of the Cu–Cr–O NPs for thermal decomposition of AP was evaluated by thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). TGA/DSC results showed that the samples with different morphologies exhibited different catalytic activity in different stages of thermal decomposition of AP. Also, in the presence of Cu–Cr–O nanocatalysts, all of the exothermic peaks of AP shifted to a lower temperature, indicating the thermal decomposition of AP was enhanced. Moreover, the heat released (ΔH) in the presence of Cu–Cr–O nanocatalysts was increased to 1490 J g⁻¹.     

Nanoflower-like composites of ZnO/SiO2 synthesized using bamboo leaves ash as reusable photocatalyst

In this study, the synthesis of ZnO/SiO₂ nanocomposites using bamboo leaf ash (BLA) and tested their photocatalytic activity for rhodamine B decolorization have been conducted. The nanocomposites were prepared by the sol–gel reaction of zinc acetate dihydrate, which was used as a zinc oxide precursor, with silica gel obtained from the caustic extraction of BLA. The effect of the Zn content (5, 10, and 20 wt%) on the physicochemical characteristics and photocatalytic activity of the nanocomposites was investigated. The results of X-ray diffraction, scanning electron microscopy, gas sorption, and transmission electron microscopy characterization confirmed the mesoporous structure of the composites containing nanoflower-like ZnO (wurtzite) nanoparticles of 10–30 nm in size dispersed on the silica support. Further, the nanocomposites were confirmed to be composed of ZnO/SiO₂ by X-ray photoelectron spectroscopy analysis. Meanwhile, diffuse-reflectance UV–visible spectrophotometry analysis of the nanocomposites revealed band gap energies of 3.38–3.39 eV. Of the tested nanocomposites, that containing 10 wt% Zn exhibited the highest decolorization efficiency (99%) and fastest decolorization rate. In addition, the degradation efficiencies were not reduced significantly after five repeated runs, demonstrating the reusability of the nanocomposite catalysts. Therefore, the ZnO/SiO₂ nanocomposite obtained from BLA is a promising reusable photocatalyst for the degradation of dye-polluted water.     

Surface modification of titanium alloy with the Ti3Al + TiB2/TiN composite coatings

Laser cladding of the Ti₃Al + TiB₂ pre‐placed alloy powder on the Ti–6Al–4 V alloy in nitrogen protective atmosphere can form the Ti₃Al + TiB₂/TiN composite coating, which can dramatically improve the wear resistance of the Ti–6Al–4 V alloy surface. In this study, the Ti₃Al + TiB₂/TiN composite coatings on the Ti–6Al–4 V alloy have been researched by means of X‐ray diffraction, SEM and energy dispersive spectrometry. It was found that there is a metallurgical combination between the Ti₃Al + TiB₂/TiN composite coating and the substrate. The microhardness of the Ti₃Al + TiB₂/TiN composite coatings were 3 ~ 4 times higher than that of the Ti–6Al–4 V alloy because of the actions of the Ti₃Al + TiB₂/TiN hard phases and the grain refinement strengthening. Moreover, the wear mass losses of the Ti₃Al + TiB₂/TiN composite coatings were much lower than that of the substrate. Copyright © 2011 John Wiley & Sons, Ltd.