Simultaneous determination of seven flavonoids in Epimedium using pressurized liquid extraction and capillary electrochromatography

Herba Epimedii (known as Yinyanghuo in China) is one of the commonly used Chinese medicines. Flavonoids are considered as its active components. In this study, a CEC method was developed for the simultaneous determination of seven flavonoids, including hexandraside E, kaempferol-3-O-rhamnoside, hexandraside F, icariin, epimedin A, B, and C, in Epimedium using baicalein as internal standard (IS). The influence of relevant parameters such as buffer concentration, pH, and proportion of ACN was investigated and optimized. Baseline separation was obtained using a Hypersil C18 capillary (3 microm, 100 microm/25 cm) with a mixture of 20 mM phosphate buffer (pH 4.0)/ACN (70:30 v/v) as mobile phase running at 30 kV and 25 degrees C in 20 min. All calibration curves showed good linearity (r2 >0.9992) within test ranges. The LOD and LOQ were lower than 8.6 and 42.8 microg/mL, respectively. The RSDs of intra- and interday for relative peak areas of seven analytes were less than 3.1 and 4.4%, and the recoveries were 95.2-103.3%. Samples of different Epimedium species were analyzed using the validated method, which is useful for quality control of Epimedium and its medical preparations.     

Chiral capillary electrophoretic determination of the enantiomeric purity of homocamptothecin derivatives, promising antitumor topoisomerase I inhibitors, using highly sulfated CDs and fluorescence detection

EKC methods for the enantiomeric resolution of homocamptothecin derivatives, potent anticancer agents targeting DNA topoisomerase I selected for clinical trials, were developed using highly sulfated beta-CD as chiral selectors at acidic pH. Optimal electrophoretic conditions, with migration times under 15 min, were as follows: for the neutral homocamptothecin analog 1, a BGE of 75 mM phosphate buffer pH 2.5 (H(3)PO(4) + triethanolamine)/ACN - 95/5 v/v, with 7.5% w/v highly S-beta-CD, an applied field of 0.2 kV/cm and a fused capillary temperature control of 30 +/- 0.1 degrees C (typical current approximately 175 microA); for the cationic homocamptothecin 2, a BGE of 25 mM phosphate buffer pH 2.5 (H(3)PO(4) + TEA)/ACN - 90/10 v/v, with 2.5% w/v highly S-beta-CD, an applied field of 0.15 kV/cm and a fused capillary temperature control of 25 +/- 0.1 degrees C (typical current approximately 45 muA), and both are validated. The best results in terms of LOQ were obtained by EC with fluorescence detection: 10 ng/mL and 20 ng/mL for 1 and 2, respectively (LOQ divided by 150 for 1 and 5 for 2 with respect to UV), thus making this method particularly convenient for enantiomeric purity determination of galenic forms. UV detection appears to be an alternative to fluorescence for the analysis of the main component either for the control of galenic forms or for therapeutic adaptation. Moreover, this method exhibits better performances than HPLC.     

Improvement of Naturally Derived Food Colorant Performance with Efficient Pyranoanthocyanin Formation from Sambucus nigra Anthocyanins Using Caffeic Acid and Heat

Consumers and regulations encourage the use of naturally derived food colorants. Anthocyanins (ACN), plant pigments, are unstable in foods. In aged red wines, ACN with a free hydroxyl group at C-5 condenses to form pyranoanthocyanins (PACN), which are more stable but form inefficiently. This study attempted to produce PACN efficiently using high cofactor concentration and heat. Elderberry anthocyanins were semi-purified and caffeic acid (CA) was dissolved in 15% ethanol and diluted with a buffer to achieve ACN:CA molar ratios of 1:50, 1:100, 1:150, and 1:200, then incubated at 65 °C for 5 days. The effect of temperature was tested using ACN samples incubated with or without CA at 25 °C, 50 °C, and 75 °C for 7 days. Compositional changes were monitored using uHPLC-PDA-MS/MS. Higher CA levels seemed to protect pigment integrity, with ACN:CA 1:150 ratio showing the highest tinctorial strength after 48 h. PACN content growth was fastest between 24 and 48 h for all ACN:CA ratios and after 120 h, all ACN had degraded or converted to PACN. PACN formed faster at higher temperatures, reaching ~90% PACN in 24 h and ~100% PACN in 48 h at 75 °C. These results suggest that PACN can form efficiently from elderberry ACN and CA if heated to produce more stable pigments.     

Simultaneous determination of different classes of antibiotics in fish and livestock by CE-MS

A specific CE-MS method was developed for the simultaneous determination of 12 antibacterial residues (four sulfonamides: sulfamethazine, sulfathiazole, sulfadiazine, and sulfachlorpyridazine; four beta-lactams: amoxicillin, ampicillin, oxacillin, and penicillin V, and four quinolones: danofloxacin, enrofloxacin, ofloxacin, and flumequine) in fish and livestock. Separation conditions, sheath liquid composition and electrospray parameters were optimized to obtain adequate CE separation and a high sensitivity. CE employed a 75 cm long fused-silica capillary (50 cm thermostated plus 25 cm at room temperature) 75 microm id and a 60 mM ammonium acetate separation buffer at pH 8 with 10% of methanol. The minimum number of identification points, according to the 2002/657/EC European Decision, was achieved using an IT in multiple reaction monitoring (MRM) mode. For quantification in meat and fish samples, a two-step procedure was developed using ACN to extract the antibacterials and to precipitate the proteins and dispersive SPE, with C18 to clean up the extract. External matrix matched calibration curves were used to achieve accurate quantitative results. The LODs and LOQs (below 18 and 50 ng/kg, respectively) were in all cases lower than the maximum residue limits for these compounds in meat and fish. The recoveries ranged from 78 to 97% and the precision with RSDs lower than 18% indicate the potential of CE-MS for the analysis of multiclass antibacterial residues in food. The method was applied to meat and fish samples taken from markets, slaughterhouses, and fish farms.     

Factorial design of electrolyte systems for the separation of fatty acids by capillary electrophoresis

In this work, a capillary zone electrophoretic methodology using UV indirect detection (224 nm) for the analysis of fatty acids (FAs) in saponified oils is proposed. The electrolyte consisted of a 5 mmol l(-1) phosphate buffer, pH 7. containing 4 mmol l(-1) sodium dodecylbenzenesulfonate (SDBS) as chromophore, 4 mmol l(-1) dimethyl-beta-cyclodextrin and 45% acetonitrile (ACN). The composition of the electrolyte was optimized by a 2(3) factorial design with triplicate at the central point. The design established practical concentration boundaries for SDBS and ACN. In a defined concentration range of 2-4 l(-1), SDBS can certainly be used as a chromophore for indirect detection without imparting excessive baseline noise. For ACN, a suitable interval of 45-55% was found to enhance FAs solubilization without overflowing the system with bubble formation and current interruption. Additionally, the design revealed the importance of dimethyl-beta-cyclodextrin in the resolution of difficult pairs and its function as a solubilizing agent for long chain FAs. At the optimized conditions, nine FAs from C10 to C20, including mono- di- and tri-unsaturated C18 fatty acids were baseline separated in less than 10 min. The proposed method was applied to the separation of FAs in edible oils and polyunsaturated fatty acid enriched margarine. Additionally, spectral monitoring at 206 nm was used to confirm peak identity in the samples.     

Method development for the separation of steroids by capillary electrochromatography

A rapid capillary electrochromatography (CEC) method was developed to separate five structurally related steroid compounds from the production line of steroid hormones. The separation was performed on a Hypersil C8 MOS and Unimicro C18 stationary phases using acetonitrile (ACN), methanol (MeOH), and tetrahydrofuran (THF) as organic modifiers and tris(hydroxymethyl)aminomethane (Tris) as buffer additive. The Hypersil C8 MOS stationary phase performed best together with ACN as organic modifier and Tris buffer. The method was extensively tested for ruggedness with respect to sensitivity to temperature, ACN composition, pH change, concentration of Tris buffer, injected plug length, and run‐to‐run and day‐to‐day repeatability. The minimal detectable concentration and amount were investigated for quantification purposes. The developed CEC method was shown to be fast, rugged, and well suited for quantification of the steroids under study.     

Infrared electroabsorption spectroscopy of N,N-dimethyl-p-nitroaniline in acetonitrile/C2Cl4: solvation of the solute and self-association of acetonitrile

Solvated structures of N,N-dimethyl-p-nitroaniline (DMPNA), an analog of p-nitroaniline (PNA), and self-associated structures of acetonitrile (ACN) in mixed solvents of ACN and C(2)Cl(4) were studied using infrared (IR) electroabsorption and FTIR spectroscopies. IR electroabsorption spectroscopy measures changes in IR absorption intensity upon application of external electric field modulation, which are a sensitive probe for permanent dipole moments. In ACN/CCl(4), PNA has been shown to occur as two distinct solvated forms, namely, 1:1 and 1:2 forms, which have one and two ACN molecule(s), respectively, associated with PNA. The IR electroabsorption and FTIR measurements on DMPNA show that, unlike PNA, DMPNA occurs as a monomer in ACN/C(2)Cl(4) rather than as specific solvated structures analogous to the 1:1 and 1:2 forms because of the substitution effect. Not only does the N,N-dimethyl substitution in DMPNA hamper solvation of ACN at the N(CH(3))(2) group, but it also indirectly blocks strong interactions with ACN at the NO(2) group. Furthermore, by using the ΔA signal of DMPNA as an internal intensity standard, it was found that the dipole moment of ACN in the DMPNA/ACN/C(2)Cl(4) system is about 1.5 times larger than that of the ACN monomer in dilute CCl(4) solution. This large value of the dipole moment in the solution studied here is attributable to the formation of a head-to-tail linear dimer of ACN, whereas the antiparallel dimer is energetically more favorable in the gas phase.     

Capillary electrophoretic enantioselective determination of zopiclone and its impurities

A capillary electrophoretic enantioselective method with UV detection was developed and validated for the simultaneous quantification of zopiclone enantiomers and its impurities, zopiclone-N-oxide enantiomers, and 2-amino-5-chloropyridine, in tablets. The analytes were extracted from the tablets using ACN and were separated in an uncoated fused-silica capillary (50 μm, 42 cm effective length, 50 cm total length) using 80 mM sodium phosphate buffer pH 2.5 and 5 mM carboxymethyl-β-cyclodextrin as running buffer. The analytes and the internal standard (trimethoprim) were detected at 305 and 200 nm, respectively. A voltage of 27 kV was applied and the capillary temperature was maintained at 25°C. All enantiomers were analyzed within 8 min and linear calibration curves over the concentration range of 0.4-0.8 mg mL?1 for each zopiclone enantiomer, 0.8-1.6 μg mL?1 for 2-amino-5-chloropyridine and 0.4-0.8 μg mL?1 for each zopiclone-N-oxide enantiomer were obtained. The coefficients of correlation obtained for the linear curves were greater than 0.99. The intra-day and inter-day accuracy and precision were lower than 2% for all analytes. This validated method was employed to study the degradation and racemization of zopiclone under stress conditions. This application demonstrated the importance of a stability-indicating assay method for this drug.     

Application of programmable temperature vaporisation injection with resistive heating-gas chromatography flame photometric detection for the determination of organophosphorus pesticides

The combination of a programmable temperature vaporisation (PTV) injector with resistive heating GC (RH-GC), a form of fast GC, has been applied to the analysis of organophosphorus (OP) pesticides. The PTV injector was optimised in the 'at-once' solvent vent mode for the injection of ethyl acetate (10-40 microL) or ACN (10 microL). The short RH-GC column (5 m x 0.25 mm ID) with fast temperature ramps (up to 153 degrees C/ min) allowed the separation of a total of 20 OP pesticides in less than 6 min. Average recoveries between 67 and 119% were obtained for pesticides spiked at 0.01 mg/kg into apple and pear matrix. Extraction of orange juice with ACN provided higher recoveries (92-104%) for methamidophos, acephate and omethoate compared to ethyl acetate (62-73%). Results for analysis of OP pesticides in samples containing incurred residues were in good agreement with those obtained using GC-MS. The overall method was rapid, allowing 20 samples to be analysed in 4 h.     

Capillary electrochromatography-mass spectrometry of cationic surfactants

The CEC-MS of alkyltrimethylammonium (ATMA+) ions with chain lengths ranging from C1-C18 is optimized using an internally tapered column packed with mixed mode reversed phase/strong cation exchange stationary phase. A systematic study of the CEC separation parameters is conducted followed by evaluation of the ESI-MS sheath liquid and spray chamber settings. First, the optimization of CEC separation parameters are performed including the ACN concentration, triethylamine (TEA) content, buffer pH and ammonium acetate concentration. Using 90% v/v ACN with 0.04% v/v TEA as mobile phase, the separation of longer chain C6-C18-TMA+ surfactants could be achieved in 15 min. Lowering the ACN concentration to 70% v/v provided resolution of shorter chain C1, C2-TMA+ from C6-TMA+ although the total analysis time increased to 40 min. Furthermore, variation of both the ACN and TEA content as well as ionic strength has found to significantly influence the retention of longer chain surfactants as compared to shorter chains. The optimum CEC conditions are 70% v/v ACN, 0.04% v/v TEA, pH 3.0 and 15 mM ammonium acetate. Next, the optimization of the ESI-MS sheath liquid composition is conducted comparing methanol to isopropanol followed by the use of experimental design for analysis of spray chamber parameters. Overall, the developed CEC-ESI-MS method allows quantitative and sensitive monitoring of ATMA+ from < or =10 microg/mL down to 10 ng/mL. Utilizing the optimized CEC-ESI-MS protocol, the challenging analysis of commercial sample Arquad S-50 ATMA+ containing cis-trans unsaturated and saturated soyabean fatty acid derivatives is demonstrated.     

Application of high performance capillary electrophoresis on toxic alkaloids analysis

We employed CE to identify mixtures of the toxic alkaloids lappaconitine, bullatine A, atropine sulfate, atropine methobromide, scopolamine hydrobromide, anisodamine hydrobromide, brucine, strychnine, quinine sulfate, and chloroquine in human blood and urine, using procaine hydrochloride as an internal standard. The separation employed a fused-silica capillary of 75 microm id x 60 cm length (effective length: 50.2 cm) and a buffer containing 100 mM phosphate and 5% ACN (pH 4.0). The sample was injected in a pressure mode and the separation was performed at a voltage of 16 kV and a temperature of 25 degrees C. The compounds were detected by UV absorbance at wavelengths of 195 and 235 nm. All the ten alkaloids were separated within 16 min. The method was validated with regard to precision (RSD), accuracy, sensitivity, linear range, LOD, and LOQ. In blood and urine samples, the detection limits were 5-40 ng/mL and linear calibration curves were obtained over the range of 0.02-10 microg/mL. The precision of intra- and interday measurements was less than 15%. Electrophoretic peaks could be identified either by the relative migration time or by their UV spectrum.     

Analysis of hydroquinone and some of its ethers by using capillary electrochromatography

Capillary electrochromatography (CEC) was used for the analysis of relevant compounds in cosmetic preparation. Hydroquinone (HQ) and some of its ethers (methyl-, dimethyl-, benzyl-, phenyl-, propyl-HQ derivatives) were analyzed by using an octadecylsilica (ODS) stationary phase packed in fused-silica capillary (100 microm I.D.; 30 cm and 21.5 cm total and effective lengths, respectively). 20 mM Ammonium acetate pH 6-acetonitrile (50-70%) were the mobile phases used for the experiments. The acetonitrile (ACN) content strongly influenced the resolution of the studied compounds as well as the efficiency and the retention factor. Baseline resolution for the studied analytes was achieved at both the lowest and the highest percentage of ACN, the last one providing the shortest analysis time. Mobile phase containing 70% of ACN was therefore used for the analysis of an extract of skin-toning cream declared to contain HQ. Good repeatability of both retention times, peak areas and peak areas ratio (Asample/Ainternational standard) was found. The calibration graphs were linear in the concentration range studied (5-90 microg/ml) with correlation coefficients between 0.9975 and 09991. The analysis of the cosmetic preparation revealed the presence of HQ (1.72%, w/w) and of two additional peaks (not identified).     

Determination of major carotenoids in vegetables by capillary electrochromatography

A simple and rapid method for the isocratic separation and determination of carotenoids (carotenes and xanthophylls) in vegetables by CEC is described. The capillary column (100 microm ID, 25 cm effective length) was packed with 3 microm Hypersil ODS particles. The optimized mobile phase contained 60% ACN, 35% THF and 5% of a 5 mM Tris aqueous buffer of pH 8. beta-Carotene, lycopene and lutein were separated with efficiencies of 66 000-128 000 plates/m within a short time (less than 12 min for the last peak eluted, 13/13'-cis-beta-carotene). An excellent resolution of the three carotenoids, as well as partial resolution of their geometrical isomers, was achieved. Application to the determination of the analytes in carrot, tomato, spinach and corn was demonstrated.     

Indirect fluorescence of aliphatic carboxylic acids in nonaqueous capillary electrophoresis using merocyanine 540

A method for the analysis of aliphatic carboxylic acids (ACAs) in nonaqueous capillary electrophoresis (NACE) in conjunction with indirect laser-induced fluorescence (ILIF) using merocyanine 540 (MC 540) is described. Performing the analysis in organic solvent is advantageous when using MC 540, because of its greater quantum yield in aprotic solvent. To achieve a high dynamic reserve (DR) and optimize resolution, we have tested a number of aqueous mixtures containing alcohols and acetonitrile (ACN). The optimum buffer for the analysis of C2-C18 ACAs, in terms of sensitivity, resolution, and speed, is an aqueous mixture of 40% ACN, 30% ethanol, and 1 mM Tris at apparent pH 7.4 (adjusted with ascorbic acid). Under this condition, the DR is greater than 1000, thereby the limits of detection for acids are in the range of sub-microM to microM. Linear plots show that the dynamic ranges for the analysis of ACAs are at least two decades in concentration, with regression coefficients all greater than 0.98. The relative standard deviations of the migration times and peak heights for all ACAs are less than 2.0%. Furthermore, this simple and cost-effective method has been applied to the analysis of marine lipid concentrate, with the concentrations of 1.67+/-0.03 and 4.50+/-0.05 mM (n = 5) for C14 and C16 acids, respectively, in a tablet of marine lipid concentrate sample.     

Development of a capillary electrophoresis method for the determination of soybean proteins in soybean-rice gluten-free dietary products

CE has been applied for the first time to the simultaneous separation of soybean and rice proteins. Treated and untreated capillaries with different effective lengths as well as separation media at different pHs were tested. For that purpose, samples and standard solutions were prepared in 25:75 ACN-water media containing 0.3% v/v acetic acid. The use of an untreated capillary of 50 cm effective length together with an 80 mM borate buffer (pH 8.5) modified with 20% v/v ACN and UV detection at 254 nm were the conditions working the best. These conditions enabled the determination of soybean proteins in gluten-free dietary commercial products elaborated with soybean protein and/or soybean flour and rice flour using the standard additions calibration method. The method was linear up to 26 mg/mL of soybean proteins, the precision (expressed as RSD) was always better than 6%, and recoveries obtained for soybean proteins when spiking commercial products were very close to 100%.     

Estimation of molecular diffusivity in aqueous solution of acetonitrile by the Wilke-Chang equation

It was tried to estimate the molecular diffusivity (D(m)) of solutes in the mixtures of acetonitrile (ACN) and water by the Wilke-Chang equation. Although the information about association coefficient (α) is necessary for the calculation, it has never been proposed for ACN. The value of α was estimated as 1.37 from D(m) of benzene in ACN at 303 K experimentally measured by the peak parking method. The values of α, i.e. 2.6, 1.9, 1.5, and 1.0, which have respectively been proposed for four solvents, i.e. water, methanol, ethanol, and benzene, were correlated with two physico-chemical parameters of the solvents, i.e. solubility parameter and E(T) value. The α value for ACN was plotted around the two correlations, indicating its appropriateness. The values of D(m) calculated by the Wilke-Chang equation using the α value for ACN were compared with those measured by the peak parking method and the Aris-Taylor method in aqueous solutions of ACN. The mean square deviation of the estimation of D(m) was calculated as 8.8 and 14%. It was demonstrated that the Wilke-Chang equation can be used for estimating D(m) with a reasonable accuracy in the mixtures consisting of ACN and water.     

Analysis of phenolic compounds in extra virgin olive oil by using reversed-phase capillary electrochromatography

In this work, the simultaneous separation of ten phenolic compounds (protocatechuic, p-coumaric, o-coumaric, vanillic, ferulic, caffeic, syringic acids, hydroxytyrosol, tyrosol and oleuropein) in extra virgin olive oils (EVOOs) by isocratic RP CEC is proposed. A CEC method was optimized in order to completely resolve all the analyzed compounds by studying several experimental parameters. The influence of the stationary phase type (C(18) and C(8) modified silica gel), buffer concentration and pH as well as the organic modifier content of the mobile phase on retention factors, selectivity and efficiency were evaluated in details. A capillary column packed with Cogent bidentate C(18) particles for 23 cm and a mobile phase composed by 100 mM ammonium formate buffer pH 3/H(2)O/ACN (5:65:30 v/v/v) allowed the baseline resolution of the compounds under study in less than 35 min setting the applied voltage and temperature at 22 kV and 20 degrees C, respectively. A study, evaluating the intra- and interday precision as well as LOD and LOQ and method linearity was developed in accordance with the analytical procedures for method validation. LODs were in the range of 0.015-2.5 microg/mL, while calibration curves showed a good linearity (r(2) >0.997). The CEC method was applied to the separation and determination of these compounds in EVOO samples after a suitable liquid-liquid extraction procedure. The mean recovery values of the studied compounds ranged between 87 and 99%.     

Endgroups in Copolymers of Acenaphthylene with Methyl Methacrylate Prepared with Azoisobutyronitrile as Initiator

Copolymers of acenaphthylene (ACN) with methyl methacrylate (MMA) have been prepared with azobis(isobutyronitrile-β, β-¹³C₂) as initiator, The endgroups derived from the initiator have been examined by ¹³C-NMR spectroscopy; those attached to ACN units have been distinguished from those attached to MMA units and quantitative comparisons of their numbers have been made. It has been deduced that at 60°C ACN is four times as reactive as MMA toward the (CH₃)₂ C(CN) radical. The marked preference for initiation involving ACN means that, for all copolymers, the ratio of ACN to MMA is appreciably greater for the sites adjacent to the (CH₃)₂ C(CN)– endgroups than for the whole copolymer.     

Optimizing the separation of food dyes by capillary electrophoresis

In this work, the separation of eleven food dyes was evaluated by MEKC in electrolytes composed of tetraborate (TBS), Brij 35, and acetonitrile (ACN) using a factorial design at the following levels: TBS concentration (5 and 10 mmol L(-1)), pH (9.5 and 10.1), Brij concentration (5 and 20 mmol L(-1)), and ACN (5 and 15%). Several response functions were evaluated and indicated 10 mmol L(-1) TBS (pH 10.1), 15% ACN, and 20 mmol L(-1) Brij 35 as best values. However, baseline resolution was not achieved (R(cp) = 0.76) and the method lacked robustness. New conditions were sought by studying the dye mobility versus Brij concentration (5-20 mmol L(-1)). A set of well resolved and more uniformly spaced peaks was obtained with an electrolyte consisting of 7.5 mmol L(-1) TBS (pH 10.1), 10 mmol L(-1) Brij, and 15% ACN. Under these new conditions, complete resolution of the 11 dyes was achieved in less than 9 min. Migration time and peak area repeatabilities were better than 1.6% and 5% CV and the LODs were 0.47 to 2.3 microg mL(-1). The methodology was applied to fruit juice powders, lollipops, and other hard and soft chewable treats.     

Method development validation for corticoids in animal feed samples by liquid chromatography using a monolithic column

A LC method for corticosteroids (CC) determination in poultry feed using a Chromolith column and UV detection has been developed and validated. The method development involved the optimization of different hydro-organic mobile phases using methanol or ACN as organic modifiers, flow rate, and temperature. The optimum separation was achieved at 40 degrees C using ACN/water (21:79 v/v) as mobile phase and 3 mL/min flow rate, allowing the separation to baseline of four out of seven CC in about 10 min. Prior to LC, a sample preparation procedure previously assayed for anabolics was used. It includes a leaching process, saponification of the esters from fatty acids, and SPE. Method validation was carried out according to the EU criteria established for quantitative screening methods. The extraction efficiencies, decision limits (CCalpha), and detection capabilities (CCbeta) for these compounds were in the ranges of 86-92%, 27-36 microg/kg, and 33-43 microg/kg, respectively. The repeatability and the within-laboratory reproducibility at 1, 1.5, and 2 CCbeta concentration levels were smaller than 9.0, 5.0, and 4.2% and 9.4, 6.4, and 4.9%, respectively. The CV values of the robustness test were less than 3.8% and the accuracy was in the range of 98-103%. The proposed method was applied to other feed with satisfactory results.