Simultaneous determination of aluminium,aluminium fluoride complexes and iron in groundwater samples by new HPLC–UVVIS method

The paper presents the application of the new HPLC–UVVIS method used in speciation analysis of aluminium form Al³⁺, aluminium complexes with fluorides and iron in groundwater samples. Based on the obtained results of groundwater samples analysis, the separation of iron in the retention time ≈ 3.7, was obtained. The conditions of the occurrence of particular aluminium forms based on the speciation analysis and modeling in the Mineql program were presented and confirmed. The influence of pH and ligand concentration on forming complexes was shown. The preliminary study of aluminium complexes with sulfates based on model solutions did not allow for the separation of the above complexes in presented analytical system. The paper presents the possible types of transformation of aluminium hydroxy forms and aluminium sulfate complexes by the reaction of the sample with mobile phase. An indirect method for the determination of aluminium in the form of aluminium sulfate was proposed. The new method was successfully applied in the determination of the following aluminium forms: Al³⁺, AlF₂⁺, AlF₃⁰, AlF₄^?, AlF²⁺ and Fe³⁺.     

New insights into the magnetic properties of the Ca2Fe2O5 ferrite

Ca₂Fe₂O₅ powder samples, undoped and doped with Na⁺, Mg²⁺, Al³⁺, Ti⁴⁺, Ge⁴⁺, were prepared with different synthesis routes to investigate the origin of the weak ferromagnetic component reported in literature for calcium ferrite single crystals. XRPD and EPR measurements have shown the presence of Fe₃O₄ magnetite as impurity phase in all the samples. This ferrimagnetic phase deeply influences the magnetic behavior with features very similar to those reported in literature for Ca₂Fe₂O₅, both powders and single crystals. Our results support the hypothesis that the weak ferromagnetic component observed in Ca₂Fe₂O₅ can be also due to the presence of magnetite impurity traces in the samples.     

高效液相色谱法同时测定水体中的环丙沙星和氟甲喹

为了满足实验室测试和野外测试需要,也为其他学者研究不同抗生素之间的相互作用提供相关的资料,本研究选用环丙沙星(CIP)和氟甲喹(FLU)作为代表,建立了一种简单、稳定、易普及的高效液相色谱法用于同时快速测定水体中两种氟喹诺酮类抗生素的含量,并讨论了不同流动相及其比例和水样中几种常见阴、阳离子(Ca²⁺、Mg²⁺、Fe³⁺、Al³⁺、SO₄^2-和HCO₃^-)对抗生素测定的影响。结果表明:三乙胺对改善柱效有明显效果;低浓度离子对测试影响不大,但Fe³⁺和Al³⁺可能与固定相的表面羟基或测试组分发生配合作用,造成基线不稳。实验结果对其他研究者对于流动相的选择与优化具有借鉴意义。     

Effect of eluent composition and pH and chemiluminescent reagent pH on ion chromatographic selectivity and luminol-based chemiluminescence detection of Co, Mn and Fe at trace levels

The alkaline-luminol/H₂O₂-based chemiluminescent (CL) detection of Fe²⁺, Co²⁺, and Mn²⁺, separated with a Dionex CS5A ion chromatographic phase was studied by means of a multi-pump flow system allowing the variation of the post-column solution composition. A perchlorate gradient at pH 1.9 (with HCl) was used to separate cations partially complexed with 5.6 mM oxalate present in the eluent and necessary for the chosen separation phase. A 0.91 mM luminol, 3.3 mM H₂O₂ in 0.25 M carbonate buffer at pH 10.5 composition was chosen as CL reagent solution. The chosen pH value warrants signal repeatability and wider linearity range although absolute signal is not maximum. The CL signal was related to the pH of the two post-column mixing solutions. Calibration plots of Co²⁺ and Fe²⁺ were linear in the chosen concentration range whilst a parabolic model was the best fit for Mn²⁺. Detection limits were 0.24, 0.50 and 375 nM for Co²⁺, Fe²⁺ and Mn²⁺, respectively. The method was used to determine Co²⁺ at trace level in commercial copper chelates used for animal feeding. A comparison with a chromatographic method with spectrophotometric detection was made giving results comparable both in absolute values and accuracy.     

Determination of alkali, alkaline earth and transition metal ions in UO2, ThO2 powders and sintered (Th,U)O2 pellets by ion chromatography

An ion chromatographic method has been developed for the determination of traces of Li⁺, Na⁺, K⁺, Ca²⁺, Mg²⁺, Sr²⁺, Fe³⁺, Cu²⁺, Ni^2+, Co²⁺, Zn²⁺, Cd²⁺, Mn²⁺ in UO₂, ThO₂ powders and sintered (Th,U)O₂ pellets. This new method utilizes poly-(butadiene-maleic acid) (PBDMA) coated silica cation exchange column and mixed functionality column of anion and cation exchange to achieve the separation of alkali, alkaline earths and transition metal ions, respectively. It involves matrix separation after sample dissolution by solvent extraction with TBP (tri butyl phosphate)-TOPO (tri octyl phosphine oxide)/CCl₄. Interference of transition metal ions in the determination of alkali, alkaline earth metal ions are removed by using pyridine 2,6-dicarboxylic acid (PDCA) in the tartaric acid mobile phase. Mobile phase composition is optimized for the base line separation of alkali, alkaline earth and transition metal ions. Linear calibration graphs in the range 0.01–20 μg mL⁻¹ were obtained with regression coefficients better than 0.999. The respective relative standard deviations were also determined. Recoveries of the spiked samples are within ±10% of the expected value. The developed method is authenticated by comparison with certified standards of UO₂ and ThO₂ powders.     

Speciation analysis of mercury contaminants in water samples by RP-HPLC after solid phase extraction on modified C18 extraction disks with 1,3-bis(2-cyanobenzene)triazene

A highly sensitive and accurate method for preconcentration and determination of ultra trace amounts of inorganic mercury and organomercury compounds in different water samples is proposed. The preconcentration is achieved using octadecyl silica (C₁₈) extraction disks modified with 1,3-bis(2-cyanobenzene)triazene (CBT). The retained analytes as their triazenide complexes on the solid phase was eluted with 10 ml acetonitrile and measured by reversed-phase high-performance liquid chromatography (RP-HPLC). Type and amount of eluent, pH, amount of CBT, flow rates of sample solution and eluent have been optimized in order to obtain quantitative recovery of the analytes. The effect of interfering ions, such as Cu²⁺, Mn²⁺, Fe²⁺, Al³⁺, Zn²⁺, Cd²⁺, Ca²⁺, Mg²⁺, Ba²⁺, Pb²⁺, K⁺ and Na⁺ usually present in water samples on the recovery of the analytes has also been investigated. The enrichment factor of 100 was obtained for all mercury species and the analytical detection limits of phenylmercury, methylmercury and Hg²⁺ were found as 0.8, 1.0 and 1.3 ng l^− 1, respectively. Stability of mercury species after extraction on the modified disks was studied and the results showed that complexes collected on the disks were stable for at least 5 days. The proposed method has been applied to the quantitative determination of mercury species in natural and synthetic water samples with recoveries more than 90%.     

Electron transfer. 153. Internal electron transfer to bound cobalt(III) induced by hydroxyl radical

Hydroxyl radicals, generated in aqueous solution from Fe²⁺ and H₂O₂, react with the formato, glycolato, lactato and mandelato complexes of (NH₃)₅Co^III, extracting H·, releasing CO₂ and inducing the internal reduction of Co^III to Co²⁺; decomposition of peroxynitrous acid (O=N—OOH) in the presence of these complexes also yields Co²⁺, indicating partial utilization (15% at 22°C and pH 1) of a path involving OH·.     

Continuous Determination of Trace Amounts of Humic Acid in Natural Water by Chemiluminescence Method

A chemiluminescence (CL) method for the determination of humic acid (HA) based on the oxidation of HA with hydrogen peroxide in the presence of formaldehyde in alkaline solution is described. This method is sensitive and selective for the determination of HA in natural water. HA produces strong CL in the oxidation of HA with MnO₄⁻, Br₂, ClO⁻, and Cr₂O₇²⁻, and the H₂O₂. HA-H₂O₂-HCHO system is suitable for the determination of HA because of its high sensitivity and high selectivity. The detection limit was 50 ppb and relative standard deviation for five measurements of 0.5 ppm (w/w) HA was 1.8%. Cations such as Na⁺, K⁺, Mg²⁺, Cu²⁺, and Fe3⁺ and anions such as PO₄³⁻, NO₃⁻, CO₃²⁻, SO₄²⁻, Cl⁻, and Y⁻ (EDTA-Na) did not interfere with the determination of HA. Addition of Mn(II) increased the CL intensity. The concentration of HA in natural water determined with this method is in good agreement with that determined by fluorometric analysis.     

Thermoanalytical Study of Cu-Mg-Zn Ferrites

Homogeneous solid solution oxalates of Fe²⁺, Cu²⁺, Mg²⁺ and Zn²⁺ metals were prepared by co-precipitation from respective metal acetate solutions with oxalic acid solution. The thermogravimetric (TG) analysis of co-precipitated oxalate complexes with general formula Mg_xCu_(0.50-x)Zn_0.50Fe₂(C₂O₄)₃·nH₂O (x=0.00, 0.05, 0.10, 0.15, 0.20, 0.25, 0.30, 0.35, 0.40, 0.45, 0.50) were carried out by manual method in static air atmosphere. The total mass loss % and stepwise mass loss % values are in good agreement with theoretically calculated mass loss % values. The thermal decomposition of oxalate complexes occur at relatively lower temperatures (561 to 698 K). The lowering of decomposition temperatures may be attributed to earlier initiation of Fe²⁺ oxalate in oxalate complexes. At temperatures between 598–698 K the thermal decomposition of Cu-Mg-Zn-Fe solid solution oxalate complexes leads to formation of ferrites of spinel structure. After tampering at 873 and 1273 K, homogeneous ferrites arise, which is revealed from XRD studies. This revised version was published online in July 2006 with corrections to the Cover Date.     

Colorimetric determination of ferrous ion via morphology transition of gold nanorods

A colorimetric method is described for the determination of ferrous ion (Fe²⁺) with high sensitivity and selectivity. The method is based on catalytic etching of gold nanorod (NR). In an acid condition, Fe²⁺ reacts with H₂O₂ to produce superoxide radical (O₂ ^??) that etches gold NRs from the low energy surface along the longitudinal direction preferentially. As a result, the changes in the absorption spectrum and color of gold NR can be measured and also can be detected visually. Under the optimal conditions, the assay has very low detection limit (13.5 nM) and a linear response in a concentration range of 75 to 1 μM. The method was applied to the determination of Fe²⁺ in spiked samples of fetal bovine serum and also transferred to a kind of test stripe for use in fast practical applications. A unique colorimetric sensing method is demonstrated for the colorimetric detection of Fe²⁺, again based on the oxidation of gold nanorods which leads to the blue-shift of the absorption.

Open image in new window

Graphical abstract A unique colorimetric sensing method was shown for the colorimetric detection of Fe²⁺. Fe²⁺reacts with H₂O₂ to generate superoxide radical that oxidize gold nanorods. This leads to a color change from blue-green to pink.

     

Inorganic interferences in the 2,4-xylenol spectro-photometric method for nitrate and their elimination

A study of inorganic interferences with the 2,4-xylenol spectrophotometric method for nitrate and their elimination is reported. Fifty-three substances do not interfere with the original method. Nitrite interferes somewhat by producing a faint yellow color. Certain reducing agents (Fe²⁺, S^2-, S₂O₃^2-, and SCN^-) cause low results by reducing the nitrate in the strong sulfuric acid solution, while some oxidizing agents (Mn⁷⁺, Cr⁶⁺, V⁵⁺, and ClO₃^-) cause low results by inactivating or destroying the 2,4-xylenol. Persulfate and small amounts of H₂O₂ produce a slight deepening of the color; larger amounts of H₂O₂; cause low results, as do Cl^-, Br^-, I^-, and metals. The recommended maximum permissible limits (mg per 10-ml aliquot) for the original method are NO₂^--N, Fe²⁺, S^2-, SCN^-, V⁵⁺, ClO₃^-, Cl^-, I^-, 0.2; Mn⁷⁺, Cr⁶⁺, S₂O₈^2-, 5; H₂O₂, 0.02; S₂O₃^2-, Br^-, 0.1; metals, none. Procedures for the elimination of most of the interferences are described. Nitrite is destroyed with sulfamic acid. The interferences of reductants (Fe²⁺, S^2-, S₂O₃^2-, and SCN^-) and oxidants (Mn⁷⁺ and Cr⁶⁺) are eliminated with hydrogen peroxide, the excess of which (and S₂O₈^2-) is destroyed by boiling in the presence of Fe³⁺. The interference of Cl^-, Br^-, and I^- is eliminated by precipitation with silver sulfate. An alternative to the sulfamic acid procedure is to oxidize nitrite to nitrate with peroxide and deduct NO₂^--N from the total NO₃^--N. After elimination of interferences, a 10-ml aliquot of sample solution is treated with 17.0 ml of sulfuric acid and 2,4-xylenol, the 6-nitro-2,4-xylenol is steam-distilled into an ammonia—water—isopropanol mixture, and the yellow color is measured.     

Effect of Physiological Concentrations of Vitamin C on the Inhibitation of Hydroxyl Radical Induced Light Emission from Fe2+-EGTA-H2O2 and Fe3+-EGTA-H2O2 Systems In Vitro

Ascorbic acid (AA) has antioxidant properties. However, in the presence of Fe²⁺/Fe³⁺ ions and H₂O₂, it may behave as a pro-oxidant by accelerating and enhancing the formation of hydroxyl radicals (^•OH). Therefore, in this study we evaluated the effect of AA at concentrations of 1 to 200 µmol/L on ^•OH-induced light emission (at a pH of 7.4 and temperature of 37 °C) from 92.6 µmol/L Fe²⁺—185.2 µmol/L EGTA (ethylene glycol-bis (β-aminoethyl ether)-N,N,N′,N′-tetraacetic acid)—2.6 mmol/L H₂O₂, and 92.6 µmol/L Fe³⁺—185.2 µmol/L EGTA—2.6 mmol/L H₂O₂ systems. Dehydroascorbic acid (DHAA) at the same range of concentrations served as the reference compound. Light emission was measured with multitube luminometer (AutoLumat Plus LB 953) for 120 s after automatic injection of H₂O₂. AA at concentrations of 1 to 50 µmol/L and of 1 to 75 µmol/L completely inhibited light emission from Fe²⁺-EGTA-H₂O₂ and Fe³⁺-EGTA-H₂O₂, respectively. Concentrations of 100 and 200 µmol/L did not affect chemiluminescence of Fe³⁺-EGTA-H₂O₂ but tended to increase light emission from Fe²⁺-EGTA-H₂O₂. DHAA at concentrations of 1 to 100 µmol/L had no effect on chemiluminescence of both systems. These results indicate that AA at physiological concentrations exhibits strong antioxidant activity in the presence of chelated iron and H₂O₂.     

Silver,iron, and nickel immobilized on hydroxyapatite‐core‐shell γ‐Fe2O3 MNPs catalyzed one‐pot five‐component reactions for the synthesis of tetrahydropyridines by tandem condensation of amines,aldehydes, and methyl acetoacetate

In this study, Ag, Ni²⁺, and Fe²⁺ immobilized on hydroxyapatite‐core‐shell γ‐Fe₂O₃ nanoparticles (γ‐Fe₂O₃@HAp‐Ag, γ‐Fe₂O₃@HAp‐Ni²⁺, and γ‐Fe₂O₃@HAp‐Fe²⁺) as a new and reusable Lewis acid magnetic nanocatalyst was successfully synthesized and reported for an atom economic, extremely facile, and environmentally benign procedure for the synthesis of highly functionalized tetrahydropyridines derivatives 4a‐t is described by one‐pot five‐component reaction of 2 equiv of aldehydes 1 , 2 equiv of amines 2 , and 1 equiv of methyl acetoacetate 3 in EtOH at room temperature in good to high yields and short reaction time. The presented methodology offers several advantages such as easy work‐up procedure, reusability of the magnetic nanocatalyst, operational simplicity, green synthesis avoiding toxic reagents and solvent, mild reaction conditions, and no tedious column chromatographic separation.     

Synthesis,characterization and interaction with DNA of mononuclear metal complexes with oxolinic acid

Seven new neutral mononuclear metal complexes of VO²⁺, Mn²⁺, Fe³⁺, Co²⁺, Ni²⁺, Zn²⁺ and Cd²⁺ with the quinolone antibacterial agent oxolinic acid (=Hoxo) have been prepared and characterized with physicochemical and spectroscopic techniques. In all the complexes, oxolinic acid acts as a bidentate deprotonated ligand bound to the metal through the pyridone oxygen and one carboxylate oxygen. The metals in all the complexes are six-coordinate with slightly distorted octahedral geometry. The lowest energy model structures of the complexes Fe(oxo)₃, VO(oxo)₂(H₂O) and Mn(oxo)₂(H₂O)₂ have been determined with molecular modeling calculations. The ability of all the complexes to bind to calf-thymus DNA has been investigated with diverse spectroscopic techniques.     

Solid phase extraction of hemin from serum of breast cancer patients using an ionic liquid coated Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>/graphene oxide nanocomposite,and its quantitation by using FAAS

A nanocomposite composed of graphene oxide and magnetite (Fe₃O₄) was coated with the ionic liquid (IL) 1,3-didecyl-2-methylimidazolium chloride and used to capture and separate hemin from serum samples. The critical parameters affecting the extraction of analyte, such as pH, surfactant and adsorbent amounts, and desorption conditions were studied and optimized. Following magnetic separation and desorption with a 5:1 mixture of acetic acid and acetone, hemin (an iron porphyrin complex) was quantified by FAAS of iron. Under optimum conditions, the enrichment factor was 96. The calibration curve was linear in the 4.8 to 730 μg L^?1 concentration range, the limit of detection was 3.0 μg L^?1, and the relative standard deviations (RSDs) for single-sorbent repeatability and sorbent-to-sorbent reproducibility were less than 3.9 % and 10.2 % (n = 5), respectively. The adsorbent displayed adsorption capacity as high as 200 mg g^?1, indicating IL-coated Fe₃O₄/GO to be a good sorbent for the adsorption of hemin. The method was validated by determining serum hemin in the presence of a large excess (480-fold) of Fe³⁺ without considerable interference. The results compare well to those obtained with a commercial hemin assay kit. The results show that this method can be successfully applied to the enrichment and determination of hemin in acid digested serum samples of breast cancer patients.

Open image in new window

Graphical abstract Fe₃O₄/GO nanocomposites were coated with the ionic liquid 1,3-didecyl-2-methylimidazolium chloride and used as the sorbent for the separation and preconcentration of hemin from blood serum samples prior to determination using by flame AAS.

     

Probing the Activity of Iron Peroxo Porphyrin Intermediates in the Reaction Layer during the Electrochemical Reductive Activation of O2

Herein we report the first example of using scanning electrochemical microscopy (SECM) to quantitatively analyze O₂ reductive activation in organic media catalyzed by three different Fe porphyrins. For each porphyrin, SECM can provide in one single experiment the redox potential of various intermediates, the association constant of Fe^II with O₂, and the pK_a of the Fe^III(OOH^?)/ Fe^III(OO^2?) couple. The results obtained can contribute to a further understanding of the parameters controlling the catalytic efficiency of the Fe porphyrin towards O₂ activation and reduction.     

Axial Ligand and Spin‐State Influence on the Formation and Reactivity of Hydroperoxo–Iron(III) Porphyrin Complexes

The present study focuses on the formation and reactivity of hydroperoxo–iron(III) porphyrin complexes formed in the [Fe^III(tpfpp)X]/H₂O₂/HOO^? system (TPFPP=5,10,15,20‐tetrakis(pentafluorophenyl)‐21H,23H‐porphyrin; X=Cl^? or CF₃SO₃^?) in acetonitrile under basic conditions at ?15 °C. Depending on the selected reaction conditions and the active form of the catalyst, the formation of high‐spin [Fe^III(tpfpp)(OOH)] and low‐spin [Fe^III(tpfpp)(OH)(OOH)] could be observed with the application of a low‐temperature rapid‐scan UV/Vis spectroscopic technique. Axial ligation and the spin state of the iron(III) center control the mode of O? O bond cleavage in the corresponding hydroperoxo porphyrin species. A mechanistic changeover from homo‐ to heterolytic O? O bond cleavage is observed for high‐ [Fe^III(tpfpp)(OOH)] and low‐spin [Fe^III(tpfpp)(OH)(OOH)] complexes, respectively. In contrast to other iron(III) hydroperoxo complexes with electron‐rich porphyrin ligands, electron‐deficient [Fe^III(tpfpp)(OH)(OOH)] was stable under relatively mild conditions and could therefore be investigated directly in the oxygenation reactions of selected organic substrates. The very low reactivity of [Fe^III(tpfpp)(OH)(OOH)] towards organic substrates implied that the ferric hydroperoxo intermediate must be a very sluggish oxidant compared with the iron(IV)–oxo porphyrin π‐cation radical intermediate in the catalytic oxygenation reactions of cytochrome P450.     

Direkt-potentiometrische Konzentrationsbestimmungen mit ionensensitiven Elektroden unter Verwendung komplexierender Hilfsreaktionen

Zusammenfassung Die Grundlagen der direkt-potentiometrischen Konzentrationsbestimmung von Anionen und Kationen werden beschrieben, für die keine ionensensitiven Elektroden bekannt sind. Es wird die Konzentrationsabnahme eines Hilfsions gemessen, das mit dem analytisch zu bestimmenden Ion einen stabilen Komplex bildet.Ausführliche Angaben werden zur Bestimmung von Al³⁺ mit F^– als Hilfsion und von Ni²⁺ mit CN^– als Hilfsion gemacht. Auf die prinzipiellen Möglichkeiten einer Bestimmung von Fe²⁺, Fe³⁺, Au⁺, Hg²⁺, Th⁴⁺, Zr⁴⁺, UO₂ ²⁺, SCN^– und S₂O₃ ^2– wird eingegangen.

---

Direct-potentiometric determinations with ion-sensitive electrodes using complexing auxiliary reactions

The basic principles of the direct-potentiometric determination of several cations and anions are discussed, for which no ion-sensitive electrode is available. The decrease in concentration of an auxiliary ion is measured which forms stable complexes with the ion to be determined. Detailed information is given on the determination of Al³⁺ with F^– as auxiliary ion and of Ni²⁺ with CN^– as auxiliary ion. An outlook is presented on the possible determinations of Fe²⁺, Fe³⁺, Au⁺, Hg²⁺, Th⁴⁺, Zr⁴⁺, UO₂ ²⁺, SCN^– and S₂O₃ ^2–.

     

A Sensitive Fluorescence Quenching Method for the Determination of Iron( Ⅱ） with 1,10-Phenanthroline

A sensitive and selective fluorescence quenching method for the determination of Fe²⁺ with 1,10‐phenanthroline was developed. The fluorescence intensity of 1,10‐phenanthroline at λ_ex of 266 run and λ_em of 365 nm was constant in the range of pH 4.0 to 10.0 and decreased linearly upon addition of Fe²⁺ to its solution. This decrease was mainly due to a static quenching effect caused by the formation of a non‐fluorescent complex of Fe²⁺ with 1, 10‐phenanthroline. The total amount of iron was determined by using hydroxylamine hydrochloride to reduce Fe³⁺ to Fe²⁺. The linear range was from 5.0 × 10–⁷ to 2.0 × 10–⁵ mol/L with a detection limit of 2.4 × 10–⁸ mol/L at 3s?. The quenching constant of Fe²⁺ to 1,10‐phenanthroline was calculated to be (5.70 × 0.05) × 10⁴ L/mol at 25 °C. Effects of foreign ions on the determination of Fe²⁺ were investigated. The results of the new method for the determination of iron in tap water and natural water samples were in good agreement with those obtained by graphite atomic absorption spectrometry.     

Electrochemical study of a nonheme Fe(ii) complex in the presence of dioxygen. Insights into the reductive activation of O2 at Fe(ii) centers

Recent efforts to model the reactivity of iron oxygenases have led to the generation of nonheme Fe^III(OOH) and Fe^IV(O) intermediates from Fe^II complexes and O₂ but using different cofactors. This diversity emphasizes the rich chemistry of nonheme Fe(ii) complexes with dioxygen. We report an original mechanistic study of the reaction of [(TPEN)Fe^II]²⁺ with O₂ carried out by cyclic voltammetry. From this Fe^II precursor, reaction intermediates such as [(TPEN)Fe^IV(O)]²⁺, [(TPEN)Fe^III(OOH)]²⁺ and [(TPEN)Fe^III(OO)]⁺ have been chemically generated in high yield, and characterized electrochemically. These electrochemical data have been used to analyse and perform simulation of the cyclic voltammograms of [(TPEN)Fe^II]²⁺ in the presence of O₂. Thus, several important mechanistic informations on this reaction have been obtained. An unfavourable chemical equilibrium between O₂ and the Fe^II complex occurs that leads to the Fe^III-peroxo complex upon reduction, similarly to heme enzymes such as P450. However, unlike in heme systems, further reduction of this latter intermediate does not result in O–O bond cleavage.