Analysis of urban dust (PM<Subscript>2</Subscript>/PM<Subscript>10-2</Subscript>) in Daejeon city by instrumental neutron activation analysis

Summary As part of an air pollution monitoring study, airborne particulate matter (PM₂/PM_10-2) samples were collected from 2000 to 2003 at two sampling sites in an urban region, Daejeon, the middle of Korea. Mass concentrations of both fine and coarse fractions and that of the black carbon in the fine particles were measured using the Gent stacked filter unit sampler and the smoke stain reflectometer, respectively. In the collected samples the concentrations of 24 elements were analyzed using instrumental neutron activation analysis. Monitored data were investigated for their temporal trends under different environmental conditions and their seasonal correlation patterns. Crustal enrichment factors were also estimated to establish the contribution between anthropogenic and crustal origin. Patterns for airborne particle matter (APM) and elemental concentrations, seasonal variation of some marker elements were investigated. The results can be applied for the investigation of further air pollution sources and for the evaluation of air quality.     

Bioaccessibility of selected trace metals in urban PM<Subscript>2.5</Subscript> and PM<Subscript>10</Subscript> samples: a model study

Bioaccessibility of trace metals originating from urban particulate matter was assessed in a worst case scenario to evaluate the uptake and thus the hazardous potential of these metals via gastric juice. Sampling was performed over a period of about two months at the Getreidemarkt in downtown Vienna. Concentrations of the assayed trace metals (Ti, Cr, Mn, Co, Ni, Cu, Zn, Mo, Ag, Cd, Sn, Sb, Tl and Pb) were determined in PM_2.5 and PM₁₀ samples by ICP-MS. The metal concentrations in sampled air were in the low picogram to high nanogram per cubic metre range. The concentrations in PM_2.5 samples were generally lower than those in PM₁₀ samples. The average daily intake of these metals by inhalation for a healthy adult was estimated to be in the range of <1 ng (Tl) to >1,000 ng (Zn). To estimate the accessibility of the inhaled and subsequently ingested metals (i.e. after lung clearance had taken place) in the size range from 2.5- to 10-μm aerodynamic equivalent diameter, a batch-extraction with synthetic gastric juice was performed. The data were used to calculate the bioaccessibility of the investigated trace metals. Extractable fractions ranged from 2.10% (Ti in PM_2.5) to 91.0% (Cd in PM_2.5), thus yielding bioaccessible fractions (PM_2.5–10) from 0.16 ng (Ag) to 178 ng (Cu).     

Toxic elements content in PM<Subscript>10</Subscript> samples from a coastal area of the Northern Adriatic Sea

PM₁₀ samples were collected during winter and summer seasons at two different sites in the area of Trieste (Italy). The content of As, Cd, Cr, Mn, Ni, Pb and V in the PM₁₀ samples was determined by inductively coupled plasma-mass spectrometry, with the purpose of evaluating the relevance of PM₁₀ inhalation as a route of human exposure to these elements. The results showed that the ambient air concentration of the aforementioned elements were below the limits or target values for both sites and season. Site and season-specific correlation analysis was conducted for the identification of metals with similar origin: very good correlation for the couple Ni-V was found in both sites and seasons, showing the influence of combustion of heavy oils in PM₁₀ composition. The inter-site and seasonal variability of both PM₁₀ and metal concentrations were examined. A stronger impact by the vehicular traffic on the PM₁₀ and metal concentrations was found for the urban site in both seasons. Because of the great importance of the “Bora” wind on the local climate, variability of PM₁₀ and toxic elements concentration with wind were analysed, allowing determination of the effect of wind on dilution of the pollutants for the urban site during both seasons.      

Physicochemical properties of ceramic tape involving Ca<Subscript>0.05</Subscript> Ba<Subscript>0.95</Subscript> Ce<Subscript>0.9</Subscript>Y<Subscript>0.1</Subscript>O<Subscript>3</Subscript> as an electrolyte designed for electrolyte-supported solid oxide fuel cells (IT-SOFCs)

Energetic materials such as a mixture of guanidine nitrate (GN)/basic copper nitrate (BCN) are used as gas generators in automotive airbag systems. However, at the time of the airbag inflation, the gas generators release toxic combustion gases such as CO, NH₃, and NO_x. In this study, we investigated the combustion and thermal decomposition behaviors of GN/BCN mixture, focusing primarily on their exhaust gas composition. As a result, when the exhaust gas of the combustion under constant pressure in an inert gas stream was analyzed using a detection tube, the amount of NO_x (mainly NO) yielded greater decrease with increasing atmospheric pressure as compared to the amounts of CO and NH₃. Thus, provided GN/BCN is ignited in a closed container, a large amount of NO_x is presumed to have been released during the initial stage of combustion, which yielded comparatively low pressure. Results of the thermogravimetry–differential scanning calorimetry–Fourier transform infrared spectroscopy (TG/DSC/FTIR) indicated that the GN/BCN mixture caused endothermic decomposition at 170 °C and exothermic decomposition at 208 °C, which was accompanied by 66% mass loss. The decomposition gases, CO₂, N₂O, and H₂O, were detected via FTIR spectrum. Because N₂O was not detected in the combustion gas, it was suggested that the detected N₂O was generated at a low temperature and decomposed in high-temperature combustion.     

Thermal behavior of Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>/TiO<Subscript>2</Subscript> mesoporous gels

Summary Titania-based photocatalytic materials were prepared by sol-gel method using Fe³⁺ and polyethyleneglycol (PEG₆₀₀) as additives. Thermogravimetry (TG), differential thermal analysis (DTA) and evolved gas analysis (EGA) with MS detection were used to elucidate processes that take place during heating of Fe³⁺ containing titania gels. The microstructure development of the Fe₂O₃/TiO₂ gel samples with and without PEG₆₀₀ admixtures was characterized by emanation thermal analysis (ETA) under in situ heating in air. A mathematical model was used for the evaluation of ETA results. Surface area and porosity measurements of the samples dried at 120&deg;C and the samples preheated for 1 h to 300 and 500&deg;C were compared. From the XRD measurements it was confirmed that the crystallization of anatase took place after thermal heating up to 600&deg;C.     

Catalytic removal of soot particles over MnCo<Subscript>2</Subscript>O<Subscript>4</Subscript> catalysts prepared by the auto-combustion method

Soot removal for exhaust gas from diesel engine has been addressed due to the more stringent legislation and environmental concerns. MnCo₂O₄ catalysts were systematically prepared using glucose as a fuel via the auto-combustion method and applied for soot removal. The as-prepared samples were characterized by X-ray diffraction (XRD), O₂-temperature-programmed oxidation (TPO) reaction and H₂-temperature-programmed reduction reaction (H₂-TPR). The catalytic activities for soot combustion were evaluated by micro activity test (MAT) with a tight contact mode between soot and catalysts. Compared with catalysts prepared by the solid state method without glucose, auto-combustion method in the presence of glucose can decrease the synthetic temperature, avoiding high temperature treatment and sintering. The catalysts prepared with glucose could catalyze soot oxidation effectively and the derived values of T₁₀, T₅₀, and T₉₀ were 326, 408, and 468 °C in a tight contact mode, respectively, showing a significant drop of T₁₀, T₅₀, and T₉₀ by 156, 177, and 178 °C for non-catalytic reaction.     

Mechanism of the initiation of combustion in CH<Subscript>4</Subscript>(C<Subscript>2</Subscript>H<Subscript>2</Subscript>)/Air/O<Subscript>3</Subscript> mixtures by laser excitation of the O<Subscript>3</Subscript> molecules

The possibility of enhancing the ignition and combustion of the CH₄/air/O₃ and C₂H₂/air/O₃ mixtures by exciting the asymmetric vibrations of the O₃ molecule with CO₂ laser radiation is considered. Even the admixture of small amounts of O₃ (2.5–5.0 vol %) into the hydrocarbon/air mixtures intensifies ignition and shortens the induction period. The excitation of the O₃ molecules with 9.7-μm radiation speeds up the chain process and further reduces the induction period and the ignition temperature. The induction period can be shortened by a factor of 10–100 even at low radiation energies absorbed by the gas (E _S = 10^?3-10^?2 J/cm³).     

Characterization of dust material emitted during harbour activities by k<Subscript>0</Subscript>-INAA and PIXE

The growing concern about air quality in harbours is a result of the high impact of the operations on human health and environment. Harbour activities such loading, unloading and transport of dusty materials are important emission sources of Atmospheric particulate matter (APM). The assessment of these fugitive emissions is a difficult task because they depend on the materials, the type of operation and the meteorological scenarios. The main objectives of this work were (1) to evaluate if the techniques k₀-based Instrumental neutron activation analysis (k₀-INAA) and Particle induced X-ray emission (PIXE) are suitable techniques to assess fugitive emissions in harbours and (2) to estimate the impact of harbour activities on APM levels and composition. Several experimental campaigns were carried out in a Portuguese harbour, during unloading operations of fertilizer and phosphorite provided from Syria and Morocco. PM_2.5 and PM_2.5–10 were collected, in polycarbonate filters, by Gent samplers. The techniques k₀-INAA and PIXE were applied as sensitive analytical tools to perform a complete chemical characterization of the collected samples. Results showed that manipulation of these materials during harbour operations resulted in high emissions of particles, principally from the coarse fraction. These emissions were very affected by the granulometry and nature of the handled materials. Fertilizer emissions were characterized by high concentration of Ca, P, K, Cr, Br and Zn, whereas phosphorite handling contributed principally for the increase of Ca, P and Cr levels.     

Microwave-assisted combustion synthesis of nanocrystalline La<Subscript>2</Subscript>Mo<Subscript>2</Subscript>O<Subscript>9</Subscript> oxide-ion conductor and its characterization

Nanocrystalline La₂Mo₂O₉ oxide-ion conductor has been successfully synthesized by microwave-assisted combustion method within a very short time duration using aspartic acid as the newer fuel in a domestic microwave oven. The synthesized nanocrystalline powder showed good sinterability and reached more than 97% of theoretical density even at low temperature of 800 °C for 5 h. The sintered La₂Mo₂O₉ sample exhibited a conductivity of 0.159 S/cm in air at 750 °C.     

Synthesis of MgFe<Subscript>1.6</Subscript>Ga<Subscript>0.4</Subscript>O<Subscript>4</Subscript> by Gel Combustion Using Glycine and Hexamethylenetetramine

A powderlike material of composition MgFe_1.6Ga_0.4O₄ was synthesized by gel combustion using a glycine–hexamethylenetetramine mixture. The gel produced by the synthesis was studied by thermal analysis (TGA/DSC) and IR spectroscopy. This mixture was shown to be efficient for obtaining homogeneous nanosized MgFe_1.6Ga_0.4O₄. The morphology of the powders was characterized by scanning electron microscopy and X-ray powder diffraction analysis.     

Promotional effect of cobalt addition on catalytic performance of Ce<Subscript>0.5</Subscript>Zr<Subscript>0.5</Subscript>O<Subscript>2</Subscript> mixed oxide for diesel soot combustion

A series of Co-modified Ce_0.5Zr_0.5O₂ catalysts with different concentrations of Co (mass %: 0, 2, 4, 6, 8, 10) was investigated for diesel soot combustion. Ce_0.5Zr_0.5O₂ was prepared using the coprecipitation method and Co was loaded onto the oxide using the incipient wetness impregnation method. The activities of the catalysts were evaluated by thermogravimetric (TG) analysis and temperature-programmed oxidation (TPO) experiments. The results showed the soot combustion activities of the catalysts to be effectively improved by the addition of Co, 6 % Co/Ce_0.5Zr_0.5O₂ and that the 8 % Co/Ce_0.5Zr_0.5O₂ catalysts exhibited the best catalytic performance in terms of lower soot ignition temperature (T_i at 349°C) and maximal soot oxidation rate temperature (T_m at 358°C). The reasons for the improved activity were investigated by X-ray diffraction (XRD), Brunauer–Emmett–Teller (BET), H₂ temperature-programmed reduction (H₂-TPR), X-ray photoelectron spectroscopy (XPS) and transmission electron microscopy (TEM). These results revealed that the presence of Co could lower the reduction temperature due to the synergistic effect between Co and Ce, thereby improving the activity of the catalysts in soot combustion. The 6 % Co catalyst exhibited the best catalytic performance, which could be attributed to the greater amounts of Co³⁺ and surface oxygen species on the catalyst.     

Development and validation of a selective HPLC-ESI-MS/MS method for the quantification of glyoxal and methylglyoxal in atmospheric aerosols (PM<Subscript>2.5</Subscript>)

This study concerns the development and validation of a complete method for the analysis of two highly reactive α-dicarbonyl compounds, glyoxal (Gly) and methylglyoxal (Mgly), in atmospheric fine particulate matter (PM_2.5). Method development included optimization of sample preparation procedures, e.g., filter extraction, concentration of extracts, derivatization and solid-phase extraction (SPE) of derivatives, as well as reversed-phase liquid chromatography coupled to electrospray ion-trap mass spectrometry (HPLC-ESI-IT/MS/MS) measurement parameters. Selectivity of detection was enhanced using tandem mass spectrometric analysis in ESI positive ion mode via two multiple reaction monitoring channels, m/z 433 → m/z 250 and m/z 419 → m/z 236 for Mgly and Gly. Retention times were 9.5 and 12.5 min for Gly- and Mgly-bis-hydrazone derivatives. Calibration ranged from 0.5 to 50 ng/mL. Inter-batch precision, expressed as relative standard deviation, was <15%. The method was shown to be unaffected by the sample matrix and to have recoveries of 100% and 60% for Gly and Mgly, respectively. Improved instrumental detection limits of 0.51 and 0.62 ng/mL for Gly and Mgly were achieved using a SPE method for the purification of 2,4-dinitrophenylhydrazine derivatization reagent solutions. This permitted the method to be used for analysis of filter samples obtained during a field study at the Taunus Observatory (mount Kleiner Feldberg, Germany). PM_2.5 concentrations ranged from 0.81 to 1.18 ng/m³ for Gly and from 0.83 to 1.92 ng/m³ for Mgly. PM concentrations correlated to the concentration of NO with coefficients (R ²) of 0.67 (Gly) and 0.78 (Mgly).     

Solid-state synthesis of undoped and Sr-doped K<Subscript>0.5</Subscript>Na<Subscript>0.5</Subscript>NbO<Subscript>3</Subscript>

The solid-state synthesis of undoped K_0.5Na_0.5NbO₃ (KNN) and KNN doped with 1, 2 and 6 mol% Sr, from potassium, sodium and strontium carbonates with niobium pentoxide, was studied using thermal analysis and in situ high-temperature X-ray diffraction (HT-XRD). The thermogravimetry and the differential thermal analyses with evolved-gas analyses showed that the carbonates, which were previously reacted with the moisture in the air to form hydrogen carbonates, partly decomposed when heated to 200 °C. In the temperature interval where the reaction was observed, i.e., between 200 and 750 °C, all the samples exhibited the main mass loss in two steps. The first step starts at around 400 °C and finishes at 540 °C, and the second step has an onset at 540 °C and finishes with the end of the reaction between 630 and 675 °C, depending on the particle size distribution of the Nb₂O₅ precursor. According to the HT-XRD analysis, the perovskite phase is formed at 450 °C for all the samples, regardless of the Sr content. The formation of a polyniobate phase with a tetragonal tungsten bronze structure was detected by HT-XRD in the KNN with the largest amount of Sr dopant, i.e., 6 mol% of Sr, at 600 °C.     

High-temperature thermal behaviour of Cr-Doped LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> spinels synthesized by the sucrose-aided combustion method

Chromium doped spinels LiCr_YMn_2−YO₄ (0.2≤Y≤0.8) has been synthesized by the sucrose-aided combustion procedure. The thermal behaviour, phase homogeneity and structural characteristics of the samples were studied by thermal analysis, coupled mass spectrometry, and room-and high-temperature X-ray diffraction methods. It was found that the ‘as prepared’ samples contained residual organic impurities undetectable for X-ray diffraction, that burn out completely at 400°C. Samples treated between 400 and 750°C are single phase spinels, whose crystallites size increase from 10 to 50 nm on increasing the temperature. Cr-doping enhances the thermal stability of the spinels, which augments on increasing the Cr content Y. The enhanced thermal stability of the spinels has been accounted for based on the high excess stabilization energy of Cr³⁺ in octahedral ligand field.     

Effect of the mechanochemical treatment of a V<Subscript>2</Subscript>O<Subscript>5</Subscript>/MoO<Subscript>3</Subscript> oxide mixture on its properties

The mechanochemical treatment of a V₂O₅/MoO₃ oxide mixture (V/Mo = 70/30 at %) was performed in planetary and vibratory mills under varying treatment times and media. The resulting samples were characterized using XRD analysis, micro-Raman spectroscopy, and XPS; their specific surface areas and catalytic activities in n-butane and benzene oxidation reactions were determined. It was found that the treatment of the oxide mixture in water resulted in chaotic degradation of the parent oxides, a decrease in crystallite sizes, and an increase in the specific surface area at a sufficiently uniform oxide distribution over the sample. The treatment in ethanol was accompanied by an anisotropic deformation of the V₂O₅ crystal by layer sliding in parallel to the vanadyl plane (010) and a chaotic degradation of MoO₃ crystals. This process was accompanied by the partial nonuniform supporting of vanadium oxide crystals onto the surface of molybdenum oxide to increase the V/Mo ratio on the sample surface. In this case, the particle size of oxides decreased and the specific surface areas of samples increased. It was found that the treatment of the oxide mixture in air (dry treatment) resulted in the most significant decrease in the sizes of V₂O₅ and MoO₃ crystals and a growth in the specific surface area. The amorphization of the parent oxides and the formation of MoV₂O₈ were observed as the treatment time was increased; in this case, an excess of amorphous vanadium oxide was supported onto the surface of this compound. It was found that, in all types of mechanochemical treatment, the binding energies of the core electrons of vanadium and molybdenum remained almost unchanged to indicate the constancy of the oxidation states of these elements. Mechanochemical treatment resulted in an increase in the activity of the samples in n-butane and benzene oxidation reactions and in an increase in the selectivity of maleic anhydride formation. In this case, an increase in the specific catalytic activity of the samples correlated with a decrease in the crystallite size of vanadium oxide, whereas selectivity correlated with an increase in the relative concentration of the V₂O₅ plane (010). In these reactions, samples after dry treatment exhibited a maximum activity, which can be related to the formation of MoV₂O₈.     

Synthesis and study of solid acid materials SnO<Subscript>2</Subscript>/B<Subscript>2</Subscript>O<Subscript>3</Subscript>

SnO₂/B₂O₃ samples were produced by a reaction between SnCl₄, H₃BO₃, and (NH₂)₂CO in a boiling aqueous solution. The Sn: B molar ratio in these samples was 1: 1, 1: 2, and 1: 3. The phase composition and degree of crystallinity of these materials was studied. The surface acidity of the samples was analyzed by the method based on a temperature-programmed reaction of dehydration of 2-methyl-3-butyn-2-ol. Thermal transformations of SnO₂/B₂O₃ samples were examined by means of differential-thermal analysis.     

Magnetic,Electrical and Thermal Studies of Polypyrrole-Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> Nanocomposites

This research paper comprises of the synthesis of polypyrrole (PPy)-Fe₂O₃ nanocomposites by employing the in situ chemical oxidative polymerization method. The concentration of the filler material was adjusted between 10–50 wt % of PPy. The synthesized nanocomposites were characterized by using X-ray diffraction (XRD). Magnetic analysis and DC electrical conductivity of the samples were carried out using vibrating sample magnetometer (VSM) and two probe DC conductivity method, point towards magnetically active and electrically conductive samples. The magnetic parameters under applied magnetic field demonstrated that the values of coercivity (H _c ), saturation magnetization (M _s ) and remanence (M _r ) can be tailored by carefully controlling the amount of dopant material into the nanocomposites indicating their suitability for controllable switching devices and microwave absorption applications. The DC electrical conductivity showed an increase up to 20 wt % of filler material and thereafter a decrease in the conductivity of nanocomposites with increase in filler content is observed. Thermogravimetric analysis (TGA) showed an increase in thermal stability with an increase in ferrite content in nanocomposites.     

Solid Solutions of the System V<Subscript>2</Subscript>O<Subscript>5</Subscript>-V<Subscript>2</Subscript>O<Subscript>4</Subscript>-TiO<Subscript>2</Subscript> in Air

Gravimetry in combination with X-ray phase analysis, X-ray crystallography, and X-ray densitometry were used to determine the contents of V⁵⁺, V⁴⁺, and Ti⁴⁺ ions and vacancies in solid solutions formed by the reaction of V₂O₅ with TiO₂ in air at atmospheric pressure.     

High-temperature X-ray study of the formation and delamination of manganese-alumina spinel Mn<Subscript>1.5</Subscript>Al<Subscript>1.5</Subscript>O<Subscript>4</Subscript>

The behavior of the manganese-alumina system with Mn:Al = 1:1 on heating in air and vacuum was studied. The starting samples were mixtures of β-Mn₃O₄, α-Mn₂O₃, and γ-Al₂O₃. On heating to 950°C in air, the samples were partially oxidized into α-Mn₂O₃, and corundum α-Al₂O₃ formed along with mixed manganese-alumina cubic spinel, whose composition was close to Mn₂AlO₄. In vacuum at 1200°C, the starting sample with a ratio of Mn:Al = 1:1 transformed into the manganese-alumina spinel Mn_1.5Al_1.5O₄, which retained its cubic structure after slow cooling in vacuum. When cooled in air, this solid solution delaminated, and a nanocrystalline Mn_2.8Al_0.2O₄ phase formed, whose structure was β-Mn₃O₄ type tetragonal spinel.     

Molten salt synthesis and characterization of fast ion conductor Li<Subscript>6.75</Subscript>La<Subscript>3</Subscript>Zr<Subscript>1.75</Subscript>Ta<Subscript>0.25</Subscript>O<Subscript>12</Subscript>

The limited electrochemical stability and the flammability of the liquid electrolytes presently used in Li-ion batteries stimulates the search for alternatives including ceramic solid electrolytes. Moreover, solid electrolytes also fulfil crucial functions in various large-scale energy storage systems, e.g. as anode-protecting membranes in aqueous Li-air batteries. Here, the processing of the solid electrolytes Li₇La₃Zr₂O₁₂ is studied for applications in Li-air batteries. Molten salt method (MSM) was adopted previously on synthesis of simple oxides; to the best of our knowledge, we report for the first time the adaptation of the MSM to prepare this class of solid electrolytes. As a model compound, we prepared the garnet-related Li_6.75La₃Zr_1.75Ta_0.25O₁₂. It has been prepared by using stoichiometric amounts of La₂O₃, ZrCl₄, and Ta₂O₅ in excess 0.88 M LiNO₃:0.12 M LiCl molten salt. Subsequently, samples were heated to various temperatures in the range 600–900 °C for 6 h in air in a recrystallized alumina crucible and finally washed with distilled water to remove excess salts. The obtained Li_6.75La₃Zr_1.75Ta_0.25O₁₂ electrolyte powder was characterized by X-ray diffraction, scanning electron microscopy, X-ray photoelectron spectroscopy, Raman, and impedance spectroscopy as well as surface area measurements. The cubic single phase was obtained for samples prepared at temperatures ≥700 °C. The effects of washing with water or aqueous LiOH solution on the structure and conductivity of the phases will be discussed.