Synthesis and optoelectronic properties of alternating benzofuran/terfluorene copolymer with stable blue emission

The solution processable alternating benzofuran/terfluorene copolymer bearing side oxadiazole groups ( PBF‐OXD ) was synthesized and its optoelectronic properties and color stability were investigated. Electron‐deficient and stereohindered oxadiazole units were used as pendent groups to compensate for the poor electron‐transporting ability of a p‐type polymer backbone, to depress the intermolecular π‐stacking, and to improve solubility while retaining polymer blue emission. PBF‐OXD showed a glass transition at 135 °C and an onset decomposition temperature of ～345 °C. A simple EL device, with the configuration of ITO/PEDOT:PSS/ PBF‐OXD /Ba/Al, displayed a stable blue emission (λ_max = 434 nm), good color purity (full width half‐maximum = 59 nm), maximum brightness of 1400 cd/m², and a maximum luminance efficiency of 0.95 cd/A. The PL and EL spectra changed slightly on annealing and on increasing the applied voltage. These results show that the as‐synthesized copolymer PBF‐OXD had integrated respective functions of its different building blocks and exhibited good thermal and color stability with improved EL performance. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5488–5497, 2009     

Copolymerization of norbornene and 5‐norbornene‐2‐yl acetate using novel bis(β‐ketonaphthylamino)Ni(II)/B(C6F5)3/AlEt3 catalytic system

Vinyl‐type copolymerization of norbornene (NBE) and 5‐NBE‐2‐yl‐acetate (NBE‐OCOMe) in toluene were investigated using a novel homogeneous catalyst system based on bis(β‐ketonaphthylamino)Ni(II)/B(C₆F₅)₃/AlEt₃. The copolymerization behavior as well as the copolymerization conditions, such as the levels of B(C₆F₅)₃ and AlEt₃, temperature, and monomer feed ratios, which influence on the copolymerization were examined. Without combination of AlEt₃, the catalytic bis(β‐ketonaphthylamino)Ni(II)/B(C₆F₅)₃ exhibited very high catalyst activity for polymerization of NBE. Combination of AlEt₃ in catalyst system resulted in low conversion for polymerization of NBE. For copolymerization of NBE and NBE‐OCOMe, involvement of AlEt₃ in catalyst is necessary. Slight addition of NBE‐OCOMe in copolymerization of NBE and NBE‐OCOMe gives rise to significant increase of catalyst activity for catalytic system bis(β‐ketonaphthylamino)Ni(II)/B(C₆F₅)₃/AlEt₃. Nevertheless, excess increase of the NBE‐OCOMe content in the comonomer feed ratios results in decrease of conversion as well as activity of catalyst. The achieved copolymers were confirmed to be vinyl‐addition copolymers through the analysis of FTIR, ¹H NMR, and ¹³C NMR spectra. ¹³C NMR studies further revealed the composition of the copolymer and the incorporation rate was 7.6–54.1 mol % ester units at a content of 30–90 mol % of the NBE‐OCOMe in the monomer feeds ratios. TGA analysis results showed that the copolymer exhibited good thermal stability (T_d > 410 °C) and failed to observe the glass transitions temperature over 300 °C. The copolymers are confirmed to be noncrystalline by WAXD analysis results and show good solubility in common organic solvents. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3990–4000, 2009     

Narrow band gap D–A copolymer of indacenodithiophene and diketopyrrolopyrrole with deep HOMO level: Synthesis and application in field‐effect transistors and polymer solar cells

A novel fused ladder alternating D–A copolymer, PIDT–DPP, with alkyl substituted indacenodithiophene (IDT) as donor unit and diketopyrrolopyrrole (DPP) as acceptor unit, was designed and synthesized by Pd‐catalyzed Stille‐coupling method. The copolymer showed good solubility and film‐forming ability combining with good thermal stability. PIDT–DPP exhibited a broad absorption band from 350 to 900 nm with an absorption peak centered at 735 nm. The optical band gap determined from the onset of absorption of the polymer film was 1.37 eV. The highest occupied molecular orbital level of the polymer is as deep as ?5.32 eV. The solution‐processed organic field‐effect transistor (OFETs) was fabricated with bottom gate/top contact geometry. The highest FET hole mobility of PIDT–DPP reached 0.065 cm² V^?1 s^?1 with an on/off ratio of 4.6 × 10⁵. This mobility is one of the highest values for narrow band gap conjugated polymers. The power conversion efficiency of the polymer solar cell based on the polymer as donor was 1.76% with a high open circuit voltage of 0.88 V. To the best of our knowledge, this is the first report on the photovoltaic properties of alkyl substituted IDT‐based polymers. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis and properties of conjugated copolycondensates consisting of carbazole‐2,7‐diyl and fluorene‐2,7‐diyl

Carbazole and fluorene‐based random and alternating copolycondensates were synthesized to develop high‐performance blue light‐emitting polymers by improving electron injection ability of poly(N‐aryl‐2,7‐carbazole)s that showed intense blue electroluminescence (EL) with good hole‐injection and ‐transport ability. These copolycondensates absorbed light energy at about λ_max = 390 nm in CHCl₃ and 400 nm in film state, and fluoresced at about λ_max = 417 nm in CHCl₃ and 430 nm in the thin film state. Energy gaps between highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) of them were about 2.9 eV, and the energy levels of LUMO situated lower than that of corresponding polycarbazole. Polymer light‐emitting diode devices having configuration of indium tin oxide/poly(3,4‐ethylenedioxythiophene)‐poly(styrenesulfonate)/polymer/CsF/Al using the copolycondensates, poly(N‐arylcarbazole‐2,7‐diyl), and poly(9,9‐dialkylfluorene‐2,7‐diyl), emitted bluish EL at operating voltages lower than 7 V. The device embedded the random copolycondensate showed notably higher performance with maximum luminance of 31,200 cd m^?2 at 11.0 V, and the current efficiencies observed under operating voltages lower than 7 V were higher than those of the other devices. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Excitation Induced Emission Color Change Based on Eu(III)‐Zn(II)‐containing Polymer Complex

A novel polymer P‐1 is prepared by the reaction of the monomer 5,5′‐divinyl‐2,2′‐bipyridine and Salen‐Zn(II) via Heck cross coupling. Interestingly, P‐1 can further incorporate with Eu(TTA)₃·2H₂O to generate copolymer P‐2 with two different metal centers. P‐2 exhibits exceptional dual emissive properties which can be tuned by excitation wavelength. For example, an orange fluorescence can be obtained when P‐2 is excited at 430 nm, whereas a red emission with a huge Stoke shift of 57 nm is observed when it is excited at 345 nm. The high wavelength emission can be attributed to Eu(III) (⁵D₀→⁷F₂), which is lit by an effective photoinduced energy transfer process between P‐1 and the Eu(TTA)₃ complex. The properties of P‐2 have led to a better understanding of the energy transfer process between P‐1 and Eu(TTA)₃ moieties.     

Poly(4,8‐bis(2‐ethylhexyloxy)benzo[1,2‐b:4,5‐b′]dithiophene vinylene): Synthesis,optical and photovoltaic properties

A new benzodithiophene (BDT)‐based polymer, poly(4,8‐bis(2‐ethylhexyloxy)benzo[1,2‐b:4,5‐b′]dithiophene vinylene) (PBDTV), was synthesized by Pd‐catalyzed Stille‐coupling method. The polymer is soluble in common organic solvents and possesses high thermal stability. PBDTV film shows a broad absorption band covering from 350 nm to 618 nm, strong photoluminescence peaked at 545 nm and high hole mobility of 4.84 × 10^?3 cm²/Vs. Photovoltaic properties of PBDTV were studied by fabricating the polymer solar cells based on PBDTV as donor and PC₇₀BM as acceptor. With the weight ratio of PBDTV: PC₇₀BM of 1:4 and the active layer thickness of 65 nm, the power conversion efficiency of the device reached 2.63% with V_oc = 0.71 V, I_sc = 6.46 mA/cm², and FF = 0.57 under the illumination of AM1.5, 100 mW/cm². © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1822–1829, 2010     

Efficient π‐conjugated interrupted host polymer by metal‐free polymerization for blue/green phosphorescent light‐emitting diodes

A new aromatic host polymer poly{[1,4‐bis(9‐decylcarbazole‐3‐yl)‐2,3,5,6‐tetrafluorobenzene‐3,3′‐diyl]‐alt‐[N‐methylisatin‐2‐one‐3,3‐diyl]} (PICzFB) containing carbazole–tetrafluorinebeneze–carbazole moiety in the π‐conjugated interrupted polymer backbone was synthesized by superacid‐catalyzed metal‐free polyhydroxyalkylation. The resulted copolymer PICzFB showed a comparatively wide band gap up to 3.32 eV and high triplet energy (E_T) of 2.73 eV due to confined conjugation by the δ? C bond interrupted polymer backbone. Blue and green light‐emitting devices with PICzFB as host, FIrpic and Ir(mppy)₃ as phosphorescent dopants showed the maximum luminous efficiencies of 5.0 and 27.6 cd/A, respectively. The results suggested that the strategy of incorporating bipolar unit into the π‐conjugated interrupted polymer backbone can be a promising approach to obtain host polymer with high triplet level for solution‐processed blue and green phosphorescent polymer light‐emitting diodes. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1037–1046     

Design and synthesis of dithieno[3,2‐b:2′3′‐d]pyrrole‐based conjugated polymers for photovoltaic applications: consensus between low bandgap and low HOMO energy level

A strategy of the fine‐tuning of the degree of intrachain charge transfer and aromaticity of polymer backbone was adopted to design and synthesize new polymers applicable in photovoltaics. Three conjugated polymers P1 , P2 , and P3 were synthesized by alternating the electron‐donating dithieno[3,2‐b:2′3′‐d]pyrrole (D) and three different electron‐accepting (A) segments ( P1 : N‐(2‐ethylhexyl)phthalimide; P2 : 1,4‐diketo‐3,6‐diphenylpyrrolo[3,4‐c]pyrrole; and P3 : thiophene‐3‐hexyl formate) in the polymer main chain. Among the three polymers, P2 possessed the broadest absorption band ranging from 300 to 760 nm, the lowest bandgap (1.63 eV), and enough low HOMO energy level (?5.27 eV) because of the strong intrachain charge transfer from D to A units and the appropriate extent of quinoid state in the main chain of P2 , which was convinced by the theoretical simulation of molecular geometry and front orbits. Photovoltaic study of solar cells based on the blends of P1 – P3 and [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) demonstrated that P2 :PCBM exhibited the best performance: a power conversion efficiency of 1.22% with a high open‐circuit voltage (V_OC) of 0.70 V and a large short‐circuit current (I_SC) of 5.02 mA/cm² were achieved. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

New preparative procedure for photoluminescent metallopolymers having a biphenyl‐2,2′‐diyl iridium(III) unit bound to a phosphine copolymer ligand

We first prepared polymer‐bound photoluminescent iridium complexes bearing a cyclometalated 2,2′‐biphenylene ligand via an easy procedure in which the metallopolymer was synthesized by the reaction of a metal precursor with a polymer ligand. The iridium compound, [Ir(cod)(biph)Cl]₂ (where cod and biph are 1,5‐cyclooctadiene and biphenyl‐2,2′‐diyl, respectively), was used as the iridium material, and a copolymer built by the radical copolymerization of 4‐styryldiphenylphosphine and methyl methacrylate was employed as the polymer ligand. The obtained metallopolymers were highly crosslinked by iridium atoms forming P? Ir? P bonds. The content of the iridium was experimentally clarified to be in the range of 0.06–0.6 mmol/g of the polymer. Photoluminescence of the iridium polymer in the solid state was observed at 597 nm when the polymer was irradiated at 350 nm. As the Ir content in the copolymer increased to 0.2 mmol/g, the intensity of the luminescence also increased, but more iridium content decreased the intensity. Furthermore, the intensity of the photoluminescence in these photoluminescent polymers depended on the molecular weight of the copolymer ligands. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4204–4213, 2006     

Novel 9,9′‐(1,3‐phenylene)bis‐9H‐carbazole‐containing copolymers as hole‐transporting and host materials for blue phosphorescent polymer light‐emitting diodes

Novel photo‐crosslinkable hole‐transport and host materials incorporated into multilayer blue phosphorescent polymer light‐emitting diodes (Ph‐PLEDs) were demonstrated in this study. The oxetane‐containing copolymers, which function as hole‐transport layers (HTL), could be cured by UV irradiation in the presence of a cationic photoinitiator. The composition of the two monomers was varied to yield three different hole‐transporting copolymers, [Poly(9,9′‐(5‐(((4‐(7‐(4‐(((3‐methyloxetan‐3‐yl)methoxy)methyl)phenyl)octan‐3‐yl)benzyl)oxy)methyl)?1,3‐phenylene)bis(9H‐carbazole)) ( P(mCP‐Ox)‐I , ‐II , and ‐III )]. In addition, monomer 1 was copolymerized with styrene to produce copolymer P(mCP‐Ph) as a host material for bis[2‐(4,6‐difluorophenyl)pyridinato‐C²,N](picolinato)iridium(III) (FIrpic), a blue‐emitting dopant. All mCP‐based copolymers displayed high glass transition temperatures (T_g) of up to 130–140 °C and triplet energies of up to 3.00 eV. The blue Ph‐PLEDs exhibited a maximum external quantum efficiency of 2.55%, in addition to a luminous efficiency of 8.75 cd A^?1 when using the device configuration of indium tin oxide/poly(3,4‐ethylenedioxythiophene):poly(styrene sulfonate)/ P(mCP‐OX)‐III / P(mCP‐Ph) :FIrpic(15 wt %)/3,3′‐[5′‐[3‐(3‐pyridinyl)phenyl][1,1′:3′,1′′‐terphenyl]‐3,3′′‐diyl]bispyridine/LiF/Al. The device bearing P(mCP‐Ox)‐III HTL, containing the highest composition of mCP unit, exhibited better performance than the other devices, which is attributed to induction of more balanced charge carriers and carrier recombination in the emissive layer. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 707–718     

Synthesis,characterization, and electroluminescence of novel copolyfluorenes and their applications in white light emission

New copolyfluorenes (PC8OF0–PC8OF50) comprised of 9,9‐dioctylfluorene and jacketed units 2,5‐bis[(5‐octyloxy‐phenyl)‐1,3,4‐ oxadiazole]‐1‐(3,5‐dibromophenyl)‐benzene (35C8) were synthesized by palladium‐catalyzed Suzuki coupling reaction. They were characterized by molecular weight determination, ¹H NMR, elemental analysis, DSC, TGA, absorption and emission spectroscopy, and cyclic voltammetry (CV). These copolymers were readily soluble in common organic solvents and exhibited high glass transition temperature and thermal stability.The copolymer films showed absorption peaks from 381 nm to 351 nm, and PL peaks from 432 nm to 421 nm with a blue shift originated from 35C8 units. Both the HOMO energy levels and LUMO levels changed little as the content of 35C8 units increased (?5.59 eV to ?5.48 eV and ?2.60 eV to ?2.49 eV). Electroluminescent devices: ITO/PEDOT:PSS[poly(ethylenedioxythiophene):polystyrenesulfonate]/polymer/Ca (25 nm)/Ag(80 nm) (a), ITO/PEDOT:PSS/polymer/TPBI [1,3,5‐ tris(N‐phenylbenzimidazol‐2‐yl)benzene](15 nm)/Mg:Ag(10:1, wt)/Ag (b), and ITO/ PEDOT:PSS/PVK[Poly(N‐vinylcarbazole)]/polymer/TPBI(15 nm)/Ca(25 nm)/Ag(80 nm) (c) were fabricated to investigate the influence of jacketed contents and device architectures on emission characteristics. The maximum brightness and current efficiency of the PC8OF25 device (5097.8 cd/m² and 0.484 cd/A) surpassed those of the PC8OF0 device (3122.8 cd/m² and 0.416 cd/A). The EL emissions of PC8OF0 – PC8OF50 were pure blue and low‐energy excimer emission bands were successfully suppressed, indicating that these copolymers could be good candidates for blue light‐emitting materials. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 4555–4565, 2009     

Tuning photovoltaic performance of 9,9‐dioctylfluorene‐alt‐5,7‐bis(thiophen‐2‐yl)‐2,3‐biphenylthieno[3,4‐b]pyrazine copolymeric derivatives by attaching additional donor units in pendant phenyl ring

A class of the 9,9‐dioctylfluorene‐alt‐5,7‐bis(thiophen‐2‐yl)‐2,3‐biphenylthieno [3,4‐b]pyrazine copolymeric derivatives (PFO‐3ThPz‐D) attaching additional donor (D) units in the pendant phenyl ring with a D‐A D structure was synthesized and investigated, where the additional D unit is a substituent group of fluorene, carbazole, and triphenylamine (Tpa). Their photovoltaic properties were significantly tuned by these pending donor units. Among these copolymers, the PFO‐3ThPz‐Tpa exhibited the best photovoltaic properties in the bulk heterojunction polymeric solar cells (BHJ‐PSC). The maximum power conversion efficiency (PCE) of 2.09% and the highest circuit current density (J_sc) of 7.91 mA/cm² were obtained in the cell using a blend of PFO‐3ThPz‐Tpa and PC₆₀BM (1:3, w/w) as active layer, which are 2.5 and 1.8 times higher than those corresponding levels in the other cell using the parent PFO‐3ThPz‐Ph copolymer instead of PFO‐3ThPz‐Tpa as donor, respectively. While PC₆₀BM was replaced by PC₇₀BM, the PFO‐3ThPz‐Tpa‐based BHJ‐PSC exhibited better photovoltaic properties with PCE of 3.08% and J_sc of 10.3 mA/cm². This work demonstrated that attaching donor units into the D‐A‐based copolymeric side‐chain is a simple and effective method to improve the photovoltaic properties for the resulting copolymers. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis and properties of poly(1‐naphthylacetylene) and poly(9‐anthrylacetylene)

Polymerizations of 1‐naphthylacetylene (1‐NA) and 9‐anthrylacetylene (9‐AA) by various transition metal catalysts were studied, and properties of the polymers were clarified. 1‐NA polymerized with WCl₆‐based catalysts to offer dark purple polymers in good yield. Especially, a binary catalyst composed of WCl₆ and Ph₃Bi gave a polymer with high molecular weight (M_w = 140×10³) and sufficient solubility in common solvents. The use of Mo and Rh catalysts, in contrast, resulted in the formation of insoluble red poly(1‐NA)s. 9‐AA gave insoluble polymers by both WCl₆‐ and MoCl₅‐based catalysts in moderate to good yields. Copolymerization of 9‐AA with 1‐NA by WCl₆–Ph₃Bi provided a soluble copolymer which exhibited the largest third‐order nonlinear optical susceptibilities (χ⁽³⁾(−3ω; ω, ω, ω) = 40×10⁻¹²) among all the substituted polyacetylenes synthesized so far. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 277–282, 1999     

High‐efficiency blue light‐emitting polymers based on 3,6‐silafluorene and 2,7‐silafluorene

A novel blue‐emitting polymer based on 3,6‐silafluorene and 2,7‐silafluorene was synthesized via the Suzuki polycondensation. The resulting polymers are readily soluble in common organic solvents, such as toluene, xylene, THF, and chloroform. The thermal, electrochemical, photophysical, and electroluminescence properties of the resulting polymers were investigated. The device fabricated from the copolymer with a configuration of ITO/PEDOT:PSS/PVK/polymer/Ba/Al exhibited an external quantum efficiency of 1.95%, a luminous efficiency of 1.69 cd A^?1 and a maximal brightness of 6000 cd m^?2. It has been found that the incorporation of the 3,6‐silafluorene unit into the poly(2,7‐silafluorene) main chain can not only improve the color purity of the devices from the resulting copolymer but also enhance its device efficiency. Moreover, no undesired long‐wavelength green emission was observed in the PL spectra of P36‐27SiF90 compared to that of PFO with a dominating emission at 500–600 nm after thermal annealing at 200 °C for 8 h. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4941–4949, 2007     

Poly[(R)‐3‐hydroxybutyrate)]/poly(styrene) blends compatibilized with the relevant block copolymer

A novel triblock copolymer PS–PHB–PS based on the microbial polyester Poly[(R)‐3‐hydroxybutyrate)] (PHB) and poly(styrene) (PS) was prepared to be used as compatibilizer for the corresponding PHB/PS blends. It was prepared in a three‐step procedure consisting of (i) transesterification reaction between ethylene glycol and a high‐molecular‐weight PHB, (ii) synthesis of bromo‐terminated PHB macroinitiator, and (iii) atom transfer radical polymerization polymerization of styrene initiated by the PHB‐based macroinitiator. Fourier transform infrared, gel permeation chromatography, ¹H‐, and ¹³C‐NMR spectroscopies were used to determine the molecular structure and/or end‐group functionalities at each step of the procedure. Although thermogravimetric analysis showed that the block copolymer underwent a stepwise thermal degradation and had better thermal stability than their respective homopolymers, differential scanning calorimetry displayed that the PHB block in the copolymer could not crystallize, and thus generating a total amorphous structure. Atomic force microscopy images indicated that the block copolymer was phase segregated in a well‐defined morphological structure with nanodomain size of ～40 nm. Contact angle measurements proved that the wettability properties of the block copolymer were in between those of the PHB and PS homopolymers. Blends analyzed for their morphology and thermal properties showed good miscibility and had well‐defined morphological features. Polymer blends exhibited lower crystallinity and decreased stiffness which was proportional to the amount of compatibilizer content in the blends. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

PL and EL behavior of near‐red luminescent metallopolymer easily prepared from phosphine‐containing copolymer and chloro{bis(1‐phenylisoquinolinato‐N,C2′)}iridium(III), and its monomeric analog

We successfully developed phosphorescent cyclometallated iridium‐containing metallopolymers, which are near‐red luminescent iridium complexes bearing phosphine‐containing copolymers used as polymer ligands, and investigated their photoluminescence and electroluminescence behavior. The phosphine copolymer ligand made from methyl methacrylate and 4‐styryldiphenylphosphine can be used as an anchor, which coordinates luminescent iridium units to form the metallopolymer easily. Organic light‐emitting diodes were fabricated from the metallopolymer and its nonpolymer analog, [IrCl(piq)₂PPh₃]. These complexes exhibited quite similar luminescence behavior, except for emission from the free‐phosphine‐units in the polymer side chain and their energy‐transferring properties from host to guest materials. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 4366–4378, 2009     

Synthesis and characterization of indenofluorene‐based copolymers containing 2,5‐bis(2‐thienyl)‐N‐arylpyrrole for bulk heterojunction solar cells and polymer light‐emitting diodes

Two novel alternating π‐conjugated copolymers, poly[2,8‐(6,6′,12,12′‐tetraoctyl‐6,12‐dihydroindeno‐[1,2b]fluorene‐ alt‐5(1‐(2,6‐diisopropylphenyl)‐2,5‐di(2‐thienyl)pyrrole) ( P1 ) and poly[2,8‐(6,6′,12,12′‐tetraoctyl‐6,12‐dihydroindeno‐[1,2b]fluorene‐ alt‐5(1‐(p‐octylphenyl)‐2,5‐di(2‐thienyl)pyrrole) ( P2 ), were synthesized via the Suzuki coupling method and their optoelectronic properties were investigated. The resulting polymers P1 and P2 were completely soluble in various common organic solvents and their weight‐average molecular weights (M_w) were 5.66 × 10⁴ (polydispersity: 1.97) and 2.13× 10⁴ (polydispersity: 1.54), respectively. Bulk heterojunction (BHJ) solar cells were fabricated in ITO/PEDOT:PSS/polymer:PC₇₀BM(1:5)/TiO_x/Al configurations. The BHJ solar cell with P1 :PC₇₀BM (1:5) has a power conversion efficiency (PCE) of 1.12% (J_sc= 3.39 mA/cm², V_oc= 0.67 V, FF = 49.31%), measured using AM 1.5 G solar simulator at 100 mW/cm² light illumination. We fabricated polymer light‐emitting diodes (PLEDs) in ITO/PEDOT:PSS/emitting polymer:polyethylene glycol (PEG)/Ba/Al configurations. The electroluminescence (EL) maxima of the fabricated PLEDs varied from 526 nm to 556 nm depending on the ratio of the polymer to PEG. The turn‐on voltages of the PLEDs were in the range of 3–8 V depending on the ratio of the polymer to PEG, and the maximum brightness and luminance efficiency were 2103 cd/m² and 0.37 cd/A at 12 V, respectively. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3169–3177, 2010     

Addition polymerization of norbornene using bis(β‐ketoamino)nickel(II)/tris(pentafluorophenyl)borane catalytic systems

Norbornene polymerizations proceeded in toluene with bis(β‐ketoamino)nickel(II) {Ni[CH₃C(O)CHC(NR)CH₃]₂ [R = phenyl ( 1 ) or naphthyl ( 2 )]} complexes as the catalyst precursors and the organo‐Lewis compound tris(pentafluorophenyl)borane [B(C₆F₅)₃] as a unique cocatalyst. The polymerization conditions, such as the cocatalyst/catalyst ratio (B/Ni), catalyst concentration, monomer/catalyst ratio (norbornene/Ni), polymerization temperature, and polymerization time, were studied in detail. Both bis(β‐ketoamino)nickel(II)/B(C₆F₅)₃ catalytic systems showed noticeably high conversions and activities. The polymerization activities were up to 3.64 × 10⁷ g of polymer/mol of Ni h for complex 1 /(B(C₆F₅)₃ and 3.80 × 10⁷ g of polymer/mol of Ni h for complex 2 /B(C₆F₅)₃, and very high conversions of 90–95% were maintained; both polymerizations provided high‐molecular‐weight polynorbornenes with molecular weight distributions (weight‐average molecular weight/number‐average molecular weight) of 2.5–3.0. The achieved polynorbornenes were confirmed to be vinyl‐addition and atactic polymers through the analysis of Fourier transform infrared, ¹H NMR, and ¹³C NMR spectra, and the thermogravimetric analysis results showed that the polynorbornenes exhibited good thermal stability (decomposition temperature > 410 °C). © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4733–4743, 2007     

Hydroxyl‐ and amine‐terminated hyperbranched polyurethanes using AB2‐type azide monomers: Synthesis,characterization, fluorescence,and charge‐transfer complexation studies

Novel AB₂‐type azide monomers such as 3,5‐bis(4‐methylolphenoxy)carbonyl azide (monomer 1) , 3,5‐bis(methylol)phenyl carbonyl azide (monomer 2) , 4‐(methylol phenoxy) isopthaloyl azide (monomer 3) , and 5‐(methylol) isopthaloyl azide (monomer 4) were synthesized. Melt and solution polymerization of these monomers yielded hydroxyl‐ and amine‐terminated hyperbranched polyurethanes with and without flexible ether groups. The structures of theses polymers were established using FT‐IR and NMR spectroscopy. The molecular weights (M_w) of the polymers were found to vary from 3.2 × 10³ to 5.5 × 10⁴ g/mol depending on the experimental conditions used. The thermal properties of the polymers were evaluated using TGA and DSC: the polymer obtained from monomer ( 1 ) exhibited lowest T_g and highest thermal stability and the polymer obtained from monomer ( 2 ) registered the highest T_g and lowest thermal stability. All the polymers displayed fluorescence maxima in the 425–525 nm range with relatively narrow peak widths indicating that they had pure and intense fluorescence. Also, the polymers formed charge transfer (CT) complexes with electron acceptor molecules such as 7,7,8,8‐tetracyano‐quino‐dimethane (TCNQ) and 1,1,2,2‐tetracyanoethane (TCNE) as evidenced by UV‐visible spectra. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3337–3351, 2009     

Radical ring‐opening copolymerization behavior of vinyloxirane: Synthesis of copolymer from 2‐isopropenyl‐3‐phenyloxirane and styrene and its functionalization

The radical ring‐opening copolymerization of 2‐isopropenyl‐3‐phenyloxirane (1) with styrene (St) was examined to obtain the copolymer [copoly(1‐St)] with a vinyl ether moiety in the main chain. The copolymers were obtained in moderate yields by copolymerization in various feed ratios of 1 and St over 120 °C; the number‐average molecular weights (M_n) were estimated to be 1800–4200 by gel permeation chromatography analysis. The ratio of the vinyl ether and St units of copoly(1‐St) was estimated with the ¹H NMR spectra and varied from 1/7 to 1/14 according to the initial feed ratio of 1 and St. The haloalkoxylation of copoly(1‐St) with ethylene glycol in the presence of N‐chlorosuccinimide produced a new copolymer with alcohol groups and chlorine atoms in the side group in a high yield. The M_n value of the haloalkoxylated polymer was almost the same as that of the starting copoly(1‐St). The incorporated halogen was determined by elemental analysis. The analytical result indicated that over 88% of the vinyl ether groups participated in the haloalkoxylation. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3729–3735, 2000