Pre‐Irradiation Grafting of Styrene/Divinylbenzene onto Poly(tetrafluoroethylene‐co‐hexafluoropropylene) from Non‐Solvents

Pre‐irradiation grafting of styrene/divinylbenzene (DVB) onto poly(tetrafluoroethylene‐co‐hexafluoropropylene) (FEP) films was studied with respect to the influence of solvent. Particularly favorable grafting conditions with long radical lifetimes and reasonably high polymerization rates were achieved with solvents that are precipitants for the newly formed polystyrene, e.g., low‐molecular‐mass alcohols like ⁱPrOH, AcOH, their mixtures with H₂O, and H₂O/surfactant systems. Using one of these solvents significantly extended the range of accessible graft levels, and a specific degree of grafting was obtained at a much lower monomer concentration and irradiation dose than with grafting in a good solvent such as toluene. As practical consequences, the monomer was used more efficiently, and the radiation damage of the perfluorinated base material was reduced with the result of improved mechanical properties of the grafted films.     

Radiation‐induced graft modification of knitted poly(ethylene terephthalate) fabric for collagen immobilization

Radiation‐induced graft co‐polymerization of methacrylic acid and N‐vinyl‐2‐pyrrolidone mixture from poly(ethylene terephthalate) knitted fabrics were conducted using a preirradiation method. The influence of the graft conditions, such as irradiation dose, reaction time, monomer concentration and temperature on the degree of grafting was determined. It was found that there is a limiting irradiation dose of 40 kGy above which the degree of grafting does not increase. An increase in the monomer concentration from 20 to 40% and an increase in temperature from 60 to 80°C gave a higher initial rate of grafting as well as higher equilibrium graft levels. The characterization of the fabric was carried out by attenuated total reflectance infrared spectroscopy (ATR‐IR), X‐ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM). The grafted fabric surface, carrying negatively charged carboxylate ions, was shown to attract collagen, being positively charged to provide bioreceptive surfaces. Copyright © 2007 John Wiley & Sons, Ltd.     

Kinetics of surface‐initiated atom transfer radical polymerization

Although atom transfer radical polymerization (ATRP) is often a controlled/living process, the growth rate of polymer films during surface‐initiated ATRP frequently decreases with time. This article investigates the mechanism behind the termination of film growth. Studies of methyl methacrylate and methyl acrylate polymerization with a Cu/tris[2‐(dimethylamino)ethyl]amine catalyst system show a constant but slow growth rate at low catalyst concentrations and rapid growth followed by early termination at higher catalyst concentrations. For a given polymerization time, there is, therefore, an optimum intermediate catalyst concentration for achieving maximum film thickness. Simulations of polymerization that consider activation, deactivation, and termination show trends similar to those of the experimental data, and the addition of Cu(II) to polymerization solutions results in a more constant rate of film growth by decreasing the concentration of radicals on the surface. Taken together, these studies suggest that at high concentrations of radicals, termination of polymerization by radical recombination limits film growth. Interestingly, stirring of polymerization solutions decreases film thickness in some cases, presumably because chain motion facilitates radical recombination. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 386–394, 2003     

Synthesis of thermo‐responsive microgels in supercritical carbon dioxide using ethylene glycol dimethacrylate as a cross‐linker

Herein, we report the preparation of thermo‐responsive polymers in a green medium. The white, dry, fine powders were obtained directly from the cross‐linking polymerization of N‐isopropylacrylamide (NIPA) in supercritical carbon dioxide (scCO₂) at pressures ranging from 10 to 28 MPa utilizing ethylene glycol dimethacrylate (EGDMA) as a cross‐linker. The effects of reaction pressure, cross‐linker ratio, initiator concentration, and reaction time were investigated. In the presence of this cross‐linker (26.4% w/w), much smaller poly(N‐isopropylacrylamide) (PNIPA) microgels (<0.2 µm diameter) were formed, and it was shown that the particle size and the morphology of the polymer were strongly dependent on the cross‐linker ratio in scCO₂. Copyright © 2009 John Wiley & Sons, Ltd.     

Kinetic analysis of surface‐initiated SET‐LRP of poly(N‐isopropylacrylamide)

The single‐electron transfer living radical polymerization (SET‐LRP) of N‐isopropylacrylamide (NIPAM) from silicon wafer modified with an initiator layer composed of 2‐bromopropionyl bromide (2‐BPB) fragments is described. The amount of Cu(0) generated in situ by the disproportination of Cu(I) to Cu(0) and Cu(II) in the presence of 2,2′‐bipyridine (2,2′‐bpy) ligand and N,N‐dimethylformamide (DMF) solvent at 90 °C is dependent on the ratio of [CuBr]/[CuBr₂]. By proper selection of the [CuBr]/[CuBr₂] ratio, well‐controlled SET‐LRP polymerization of NIPAM was observed such that the thickness of the layer consisting of chains grown from the surface increased linearly with the molecular weight of chains polymerized in solution in identical. In addition, the calculation of grafting parameters, including surface coverage, σ (mg/m²); grafting density, Σ (chain/nm²); and average distance between grafting sites, D (nm), from the number‐average molecular weight, M _n (g/mol), and ellipsometric thickness, h (nm), values indicated the synthesis of densely grafted poly(NIPAM) films and allowed us to predict a “brush‐like” conformation. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Cellulose‐based macroinitiator for crosslinked poly(butyl methacrylate‐co‐pentaerythritol triacrylate) oil‐absorbing materials by SET‐LRP

Cellulose produced from cotton fibers was used as substrate for synthesis of oil‐absorbing materials by single electron transfer‐living radical polymerization. The cellulose macroinitiator was prepared by esterification of hydroxyl group with 2‐bromoisobutyryl bromide (BiBB), followed by grafting with butyl methacrylate (BMA) and pentaerythritol triacrylate (PETA) to render a three‐dimensional architecture. The polymerization was catalyzed by Cu(0) powder/hexamethylenetetramine (HMTA) and performed in N,N‐dimethylformamide (DMF). Effects of cellulose, catalyst, reaction temperature, and time were investigated in detail. The maximum oil absorption to chloroform and toluene could reach 29.0 and 15.4 g·g^?1, respectively. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Synthesis and characterization of silica–polyvinyl imidazole core–shell nanoparticles via combination of RAFT polymerization and grafting‐to method

The silica–polyvinyl imidazole core–shell nanoparticles (silica/PVI NPs) with controlled shell thickness and narrow distribution size were fabricated via “grafting‐to” method. First, O‐ethyl xanthate terminated PVI with various chain lengths was produced via the reversible addition–fragmentation chain transfer (RAFT) polymerization using O‐ethyl‐S‐phenyl dithiocarbonate (EPDC) as RAFT agent. Next, three synthesized PVI of different molecular weights (3.4, 6.6, and 11 kg/mol) were successfully grafted to the methacrylate modified silica NPs from solution by radical mediated grafting‐to method. These core–shell NPs were then characterized by Fourier transform infrared spectroscopy (FTIR), X‐ray photoelectron spectrum measurements (XPS), transmission electron microscopy (TEM), and thermogravimetric analysis (TGA). Polyvinyl imidazole molecular weight, reaction time, polymer concentration, and reaction temperature were all used to control the grafting reaction for PVI grafting densities and shell thicknesses. The highest grafting density obtained was close to 1.2 chains/nm² and was achieved for 3.4 kg/mol PVI at 80°C. The prepared silica/PVINP displayed efficient antifouling properties and stability in concentrated sodium chloride aqueous solutions over a broad pH range for a period of at least 7 days. Copyright © 2017 John Wiley & Sons, Ltd.     

Thiol‐acrylate main‐chain liquid‐crystalline elastomers with tunable thermomechanical properties and actuation strain

The purpose of this study was to investigate the influence of cross‐linking on the thermomechanical behavior of liquid‐crystalline elastomers (LCEs). Main‐chain LCE networks were synthesized via a thiol‐acrylate Michael addition reaction. The robust nature of this reaction allowed for tailoring of the behavior of the LCEs by varying the concentration and functionality of the cross‐linker. The isotropic rubbery modulus, glass transition temperature, and strain‐to‐failure showed strong dependence on cross‐linker concentration and ranged from 0.9 MPa, 3 °C, and 105% to 3.2 MPa, 25 °C, and 853%, respectively. The isotropic transition temperature (T_i) was shown to be influenced by the functionality of the cross‐linker, ranging from 70 °C to 80 °C for tri‐ and tetra‐functional cross‐linkers. The magnitude of actuation can be tailored by controlling the amount of cross‐linker and applied stress. Actuation increased with increased applied stress and decreased with greater amounts of cross‐linking. The maximum strain actuation achieved was 296% under 100 kPa of bias stress, which resulted in work capacity of 296 kJ/m³ for the lowest cross‐linked networks. Overall, the experimental results provide a fundamental insight linking thermomechanical properties and actuation to a homogenous polydomain nematic LCE networks with order parameters of 0.80 when stretched. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 157–168     

Kinetic study of preirradiation grafting of acrylic acid onto poly(tetrafluoroethylene–perfluorovinyl ether) copolymer

A kinetic study has been made on the preirradiation grafting of acrylic acid (AAc) onto poly(tetrafluoroethylene–perfluorovinyl ether) (PFA) film. The effect of grafting conditions was investigated. The dependences of the grafting rate on preirradiation dose and monomer concentration was found to be of the order of 0.5 and 1.3, respectively. The final degree of grafting was found to increase with dose and monomer concentration. However, it decreases as the grafting temperature increase. The overall activation energy for the graft polymerization was calculated from Arrhenius plots to be 5.6 kcal/mol. The activation energy for this grafting system was found to be independent of preirradiation dose used in the range from 10 to 100 kGy. The relationship between the grafting rate and film thickness gave a negative first-order dependence. The results suggest that the grafting proceeds by radical mechanism with bimolecular termination of growing chain radicals. It was reasonable concluded that this grafting proceeds from the surface to the center of film with progressive monomer diffusion through the grafted layer which swells in the monomer solution.     

A Polystyrene‐Cross‐Linking Tricyclohexylphosphine: Synthesis,Characterization and Applications to Pd‐Catalyzed Cross‐Coupling Reactions of Aryl Chlorides

A polystyrene‐cross‐linking tricyclohexylphosphine (PS‐TCP) was synthesized through radical emulsion polymerization of 4‐tert‐butylstyrene as a monomer and tris(trans‐4‐styrylcyclohexyl)phosphine as a threefold cross‐linker. The PS‐TCP showed enhanced ligand performance compared to the corresponding polystyrene‐triphenylphosphine hybrid PS‐TPP and tricyclohexylphosphine in Pd‐catalyzed Suzuki–Miyaura and Buchwald–Hartwig reactions of aryl chlorides.     

Atom‐transfer radical grafting polymerization of 2‐methacryloyloxyethyl phosphorylcholine from silicon wafer surfaces

2‐Methacryloyloxyethyl phosphorylcholine (MPC), a biomimetic monomer, was grafted from silicon wafer surfaces at room temperature by combining self‐assembly of initiator and surface‐initiated atom transfer radical polymerization. Two methods were used to control the grafting process. One was to add free initiator to the reaction system; the other was to add excess deactivator. The grafting densities up to 0.3 chains/nm² were obtained. The surface thickness increased linearly with MPC conversion. The thickness depended on catalyst and monomer concentrations, as well as activator/deactivator ratio. Poly(MPC) layers of >100 nm thick were obtained by optimizing the polymerization conditions. A second block of either poly(MPC) or poly[2‐(dimethylamino)ethyl methacrylate] was also grown from the grafted poly(MPC), demonstrating the system livingness. X‐ray photoelectron spectroscopy was used to examine the surface chemical compositions showed good agreement with the theoretical values. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2931–2942, 2004     

Controlled grafting of cellulose esters using SET‐LRP process

Here, we present the first example of application of single‐electron transfer living radical polymerization (SET‐LRP) process to a controlled grafting of cellulose esters, cellulose diacetate (CDA), and cellulose acetate butyrate (CAB). The cellulose ester macroinitiators with various functionality densities have been prepared by acylation of the backbones with 2‐bromoisobutyryl (BrIB) and dichloroacetyl (DCA) groups, respectively. Methacrylate monomers were polymerized using DCA‐functionalized macroinitiators in the presence of pentamethyldiethylene triamine as a ligand. At 30 °C, the reaction is rather slow, reaching about 10% conversion after 3 to 6 h of polymerization, whereas the higher temperature (60 °C) perceptibly speeds up the polymerization so that methyl methacrylate (MMA) conversion is ～30% after 5 h. Graft copolymers with random‐type and diblock‐type grafts having amphiphilic character were also synthesized. For acrylate grafting (BuA and t‐BuA), BrIB‐functionalized macroinitiators are more convenient in a combination with a low concentration of Cu(0) and Me₆TREN as a ligand and polymerization is detectably faster even at the lower temperature than that of MMA. Kinetic studies show “living” character of both the graftings. Important advantages of SET‐LRP, compared with classic ATRP, are (i) higher polymerization rate, (ii) lower extent of recombination of the growing grafts and (iii) negligible coloration of the products with catalytic residua, so that the prepared polymers do not require additional careful purification. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

ATRP of MMA under 60Co γ‐irradiation at room temperature

In this work, atom transfer radical polymerization (ATRP) of methyl methacrylate (MMA) was successfully carried out at room temperature (25 °C) under ⁶⁰Co γ‐irradiation environment. The polymerization proceeded smoothly with high conversion (>90%) within 7 h. The polymerizations kept the features of controlled radical polymerization: first‐order kinetics, well‐predetermined number‐average molecular weights (M_n,GPC), and narrow molecular weight distributions (M_w/M_n < 1.25). ¹H NMR spectroscope and matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry confirmed that poly(methyl methacrylate) (PMMA) chain was end‐capped by the initiator moieties. The Cu(II) concentration could reduce to 20 ppm level while keeping good control over molecular weights. This is the first successful example for the ATRP of MMA under ⁶⁰Co γ‐irradiation at room temperature. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Low‐temperature controlled free‐radical polymerization of vinyl monomers in the presence of a novel cyclic dixanthate under γ‐ray irradiation

The free‐radical polymerization of methyl acrylate (MA) has been studied in the presence of a novel cyclic dixanthate under γ‐ray irradiation (80 Gy min^?1) at room temperature (～28 °C), ?30 °C, and ?76 °C respectively. The resultant polymers have controlled molecular weights and relatively narrow molecular weight distributions, especially at low temperatures (i.e., ?30 and ?76 °C). The polymerization control may be associated with the temperature: the lower the temperature is, the more control there is. Matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry analysis of poly(methyl acrylate) (PMA) samples shows that there are at least three distributions: [3‐(MA)_n‐H]⁺ cyclic polymers, [3‐(MA)_n‐THF‐H]⁺, and [3‐(MA)_n‐(THF)₂‐H]⁺ linear PMAs. The relative content of the cyclic polymers markedly increases at a lower temperature, and this may be related to the reduced diffusion rate and the suppressed chain‐transfer reaction at the low temperature. It is evidenced that the good control of the polymerization at the low temperature may be associated with the suppressed chain‐transfer reaction, unlike reversible addition–fragmentation chain transfer polymerization. In addition, styrene bulk polymerizations have been performed, and gel permeation chromatography traces show that there is only one cyclic dixanthate moiety in the polymer chain. This article is the first to report the influence of a low temperature on controlled free‐radical polymerizations. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2847–2854, 2007     

Cross‐linking photopolymerization of monoacrylate initiated by benzophenone

The chain‐end structure of the photopolymerized acrylate using benzophenone as an initiator was investigated as well as polymerization behavior. Dodecyl acrylate was used as a monomer in this study. Gelation occurred during ultraviolet (UV) irradiation, whereas a cross‐linker was not employed. Conversion‐time profile below gel point gave a linear first‐order plot suggesting that the steady‐state was held throughout polymerization. Matrix‐assisted laser desorption/ionization time‐of‐flight mass spectra of the resultant polymer indicated that most polymers had an acryloyl group at one of the chain‐ends, while some polymers had an acryloyl group at each chain‐end. The cross‐linking reaction leading to gelation would have been caused by the subsequent copolymerization of the residual monomer with the latter polymer having two acryloyl groups. Dissolved oxygen in the monomer solution influenced the polymer structure giving hydroxyl group at chain‐end. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 1545–1553     

Surface‐initiated atom transfer radical polymerization grafting of poly(2,2,2‐trifluoroethyl methacrylate) from flat silicon wafer surfaces

Poly(2,2,2‐trifluoroethyl methacrylate) (PTFEMA), a partially fluorinated polymer, was directly grafted from silicon wafer surfaces by a surface‐initiated atom‐transfer radical polymerization (ATRP). The polymer layer thickness increased linearly with monomer conversion and molecular weight of free polymers in solution. The thickness was mainly determined by the experimental conditions such as activator/deactivator ratio, monomer/catalyst ratio, and monomer concentration. PTFEMA layers of more than 100‐nm thick were obtained. The grafted PTFEMA chains were “living” and allowed the extension of a second block of PMMA. X‐ray photoelectron spectroscopy study showed that the chemical compositions at the surfaces agreed well with their theoretical values. A novel surface‐attachable difunctional initiator was also synthesized and applied to the grafting of PTFEMA. The grafting density was doubled using this difunctional initiator, from 0.48 to 0.86 chains/nm². © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1252–1262, 2006     

Visible light‐induced living surface grafting polymerization for the potential biological applications

A novel visible light‐induced living surface grafting polymerization was developed by a strategy in which isopropyl thioxanthone (ITX) was first photoreduced under UV light and sequentially coupled onto the surface of polymeric substrates, and the produced isopropyl thioxanthone‐semipinacol (ITXSP) “dormant” groups were subsequently reactivated under visible light to initiate a surface grafting polymerization. By using glycidyl methacrylate (GMA) and low‐density polyethylene (LDPE) films as models, a “living” surface grafting polymerization initiated by ITXSP under visible light at room temperature was observed. Both the surface grafting chain length versus grafting conversion of monomer and the grafting polymerization rate versus monomer concentration demonstrated a linear dependence, which is in accord with the known characteristics of living polymerization. The livingness rendered it possible to accurately control the thickness of the grafted layer by simply altering the irradiation time. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Phys, 2009     

Efficient synthesis of monodisperse,highly crosslinked,and “living” functional polymer microspheres by the ambient temperature iniferter‐induced “living” radical precipitation polymerization

The facile and efficient one‐pot synthesis of monodisperse, highly crosslinked, and “living” functional copolymer microspheres by the ambient temperature iniferter‐induced “living” radical precipitation polymerization (ILRPP) is described for the first time. The simple introduction of iniferter‐induced “living” radical polymerization (ILRP) mechanism into precipitation polymerization system, together with the use of ethanol solvent, allows the direct generation of such uniform functional copolymer microspheres. The polymerization parameters (including monomer loading, iniferter concentration, molar ratio of crosslinker to monovinyl comonomer, and polymerization time and scale) showed much influence on the morphologies of the resulting copolymer microspheres, thus permitting the convenient tailoring of the particle sizes by easily tuning the reaction conditions. In particular, monodisperse poly(4‐vinylpyridine‐co‐ethylene glycol dimethacrylate) microspheres were prepared by the ambient temperature ILRPP even at a high monomer loading of 18 vol %. The general applicability of the ambient temperature ILRPP was confirmed by the preparation of uniform copolymer microspheres with incorporated glycidyl methacrylate. Moreover, the “livingness” of the resulting polymer microspheres was verified by their direct grafting of hydrophilic polymer brushes via surface‐initiated ILRP. Furthermore, a “grafting from” particle growth mechanism was proposed for ILRPP, which is considerably different from the “grafting to” particle growth mechanism in the traditional precipitation polymerization. © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Hairy polymeric nanocapsules with ph‐responsive shell and thermoresponsive brushes: Tunable permeability for controlled release of water‐soluble drugs

The hairy poly(methacrylic acid‐co‐divinylbenzene)‐g‐poly(N‐isopropylacrylamide) (P(MAA‐co‐DVB)‐g‐PNIPAm) nanocapsules with pH‐responsive P(MAA‐co‐DVB) inner shell and temperature‐responsive PNIPAm brushes were prepared by combined distillation–precipitation copolymerization and surface thiol‐ene click grafting reaction using 3‐(trimethoxysilyl)propyl methacrylate‐modified silica (SiO₂‐MPS) nanospheres as a sacrificial core material. The well‐defined PNIPAm was synthesized by a reversible addition fragmentation chain transfer (RAFT) polymerization. The chain end was converted to a thiol by chemical reduction. The PNIPAm was integrated into the nanocapsules via thiol‐ene click reaction. The surface thiol‐ene click reaction conduced to tunable grafting density of PNIPAm brushes. The grafting densities decreased from 0.70 chains nm^?2 to 0.15 chains nm^?2 with increasing the molecular weight of grafted PNIPAm chains. Using water soluble doxorubicin hydrochloride (DOX·HCl) as a model molecular, the tunable shell permeability of the nanocapsule was investigated in detail. The permeability constant can be tuned by controlling the thickness of the P(MAA‐co‐DVB) inner shell, the grafting density of PNIPAm brushes, and the environmental pH and temperature. The tunable shell permeability of these nanocapsules results in the release of the loaded guest molecules with manipulable releasing kinetics. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2202–2216     

A versatile and rapid coating method via a combination of plasma polymerization and surface‐initiated SET‐LRP for the fabrication of low‐fouling surfaces

In this work, we demonstrate the potential of surface‐initiated single electron transfer living radical polymerization for surface modification applications that confer low‐fouling properties. The versatility of the technique, which can be applied to a wide variety of substrates, has been displayed by the successful grafting of a range of monomers after immobilizing a bromine initiator on the surface via plasma polymerization. The thickness of the grafted surfaces can be controlled through variation of reaction parameters such as monomer concentration, reaction time, and the ratio between catalyst and ligand. Furthermore, the low‐fouling properties of the resulting surfaces were demonstrated against fully concentrated serum proteins and adhesive fibroblast cells, via grafting of N‐hydroxyethyl acrylamide (N‐HEA) or [2‐(methacryloyloxy)ethyl]dimethyl‐(3‐sulfopropyl) ammonium hydroxide (SBMA). This rapid and versatile coating technique, which has the ability to be applied to a wide range of substrates, can be performed in aqueous conditions without the exclusion of atmospheric oxygen, and shows excellent potential for the surface modification of biomaterial surfaces that require low‐fouling properties. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 2527–2536