分散固相萃取气相色谱-负化学离子源质谱法测定大豆和玉米中20种农药的残留量

建立了一种大豆和玉米中20种农药残留量的分散固相萃取气相色谱-负化学离子源质谱分析方法。样品经乙腈提取并浓缩后加入N-丙基乙二胺（PSA）、石墨化碳黑和C18 3种填料进行分散固相萃取净化,气相色谱-负化学离子源质谱分时段选择离子监测技术测定与确证,外标法定量。所有农药在20～400 μg/L范围内线性均良好;方法的定量限(LOQ)均不高于2 μg/kg;在5,10和20 μg/kg 3个添加水平下所有农药的平均回收率均处于70%～130%之间,相对标准偏差(RSD)低于17%;运用该方法检测大豆和玉米样品时没有干扰现象。     

GC-Q-TOF/MS快速筛查测定半夏中322种农药及化学污染物残留

利用GC-Q-TOF/MS检测技术,采用分散固相萃取(DSPE)样品前处理方法,建立了半夏中322种农药及化学污染物残留的筛查方法。探究了样品前处理过程中提取溶剂、缓冲盐体系、净化剂组成和用量对样品提取、净化等方面的影响,最终确定用1%的乙酸乙腈溶液和乙酸-乙酸钠缓冲体系进行提取,复合净化剂净化,GC-Q-TOF/MS测定的筛查方法。结果显示,322种农药及化学污染物中84.2%的化合物筛查限为5μg/kg,14.6%农药及化学污染物的筛查限为10μg/kg;在10,50,100μg/kg的添加水平下,农药及化学污染物的平均回收率分别为70.2%~119.5%,70.6%~119.8%,70.2%~119.9%,相对标准偏差(RSD)分别为0.2%~19.7%,0.2%~19.5%,0.5%~20.0%。与传统的分散固相萃取方法相比,该方法高效、快速,灵敏度高,准确性好,适用于半夏中322种农药及化学污染物残留的快速筛查和定量分析。     

气相色谱-负化学离子源质谱法测定聚氯乙烯塑料中的短链氯化石蜡

建立了用于聚氯乙烯(PVC)塑料中短链氯化石蜡(SCCPs)含量测定的气相色谱-负化学离子源质谱法。采用超声萃取法对PVC塑料中的SCCPs进行萃取,萃取时间为1.5 h;然后用浓硫酸法对萃取溶液进行净化处理;最后用气相色谱-质谱法在负化学电离模式、离子源温度为160℃、甲烷反应气流速为1.5 mL/min等条件下对样品中的SCCPs进行定性定量分析。该方法不受样品中中链氯化石蜡(MCCPs)的干扰,可对样品中的SCCPs进行准确的定量分析。分析的12批次样品均检出SCCPs,含量在0.3×102~3.5×104mg/kg范围内。依据欧盟对SCCP的限值(1%)要求,4批次样品不符合法规要求,不符合率为33.3%。可见,PVC塑料具有较高的SCCPs污染风险。     

五氯亚硝酰合铱酸根[Ir(NO)Cl5][-]在盐酸-磷酸三丁酯体系中的萃取行为

铱在萃取过程中的行为与其存在状态有关.王水溶解含铱物料有[Ir(NO)Cl_5]~-生成,亚硝酸盐配位法分离贵金属时,盐酸酸化可使[Ir(NO_2)_6]~(3-)转变为[Ir(NO)Cl_5]~-。[Jr(NO)Cl_5]~-在溶液中的变化极其复杂,它在冶金过程中必然影响到有关的分离.本文研究[Ir(NO)Cl_5]~-在盐酸-磷酸三丁酯(TBP)体系中的萃取行为,寻求最佳萃取条件.     

固相萃取-气相色谱/负化学电离-质谱法测定酸水解植物蛋白及酱油中的3-氯-1,2-丙二醇

建立了酸水解植物蛋白及酱油中3-氯-1,2-丙二醇(3-MCPD)的固相萃取-气相色谱/质谱测定方法。样品经Aoisa-HBL固相萃取柱萃取,正己烷-乙酸乙酯净化提取,七氟丁酰咪唑衍生,衍生物经气相色谱/负化学电离-质谱（GC/NCI-MS）选择离子模式(SIM)检测，外标法定量。3-MCPD的定量检测限为0.5 μg/kg,平均回收率为92.2%～97.4%,相对标准偏差为3.6%～10.9%。该方法检测灵敏度高，定性定量准确。     

气相色谱-正化学源-质谱联用技术测定葡萄和葡萄酒中多种唑类杀菌剂的残留量

建立了可用于葡萄和葡萄酒中20种唑类杀菌剂残留量的分散型固相萃取-气相色谱-正化学离子源质谱分析方法.葡萄和葡萄酒样品分别用乙腈(含1%冰醋酸)和乙酸乙酯提取,分散型固相萃取法净化,由气相色谱-正化学离子源质谱分时段选择离子监测技术进行测定与确证,外标法定量.20种农药在50～1000 μg/L范围内线性均良好; 所有农药的方法定量限(LOQ)均低于10 μg/kg;在3个添加水平(10, 20和40 μg/kg)下,所有农药的回收率均处于71.2%～102.2%之间, RSD≤10.6%.     

KIO4-四硼酸钠系统阻抑亮绿褪色动力学光度法测定痕量Ir（Ⅳ）

基于H2SO4介质及四硼酸钠缓冲溶液中,80℃水浴中,Ir(Ⅳ)对KIO4氧化亮绿褪色反应具有阻抑作用,据此建立了阻抑动力学光度法测定痕量Ir(Ⅳ)的新方法。阻抑反应(吸光度A)与非阻抑反应(吸光度A0)吸光度差值△A与Ir(Ⅳ)的质量浓度ρ在0.0002～0.08μg/mL范围内呈良好的线性关系,检出限为2.969×10-10g/mL。对1μg/25 mL Ir(Ⅳ)标准溶液测定的相对标准偏差为1.7%(n=11)。测定了动力学参数,反应对Ir(Ⅳ)为一级反应,试验条件下,总反应为准一级反应,表观速率系数为2.883×10-4/s,表观活化能为52.2 kJ/mol。方法用于分子筛和活性炭样品中痕量Ir(Ⅳ)测定,加标回收率在98.1%～104.9%范围,符合痕量分析要求。     

吐温80-硫酸铵-水固液体系萃取分离Rh(Ⅲ)和Ir(Ⅲ)

铑;铱;液固萃取分离;氯化亚锡;吐温80-硫酸铵-水固液体系萃取分离Rh(Ⅲ)和Ir(Ⅲ)     

KBr-乙醇-(NH_4)_2SO_4体系析相萃取分离和富集铱的研究

研究了KBr-乙醇-(NH_4)_2SO_4水体系析相萃取分离和富集铱的行为及与一些金属离子分离的条件.结果表明,(NH_4)_2SO_4能使乙醇的水溶液分成两相,在分相过程中,Ir(Ⅳ)与KBr生成的IrBr_6~(2-)与质子化乙醇(C_2H_5OH~(2+))形成的缔合物[IrBr_6~(2-)][C_2H_5OH~(2+)]_2能被乙醇相完全萃取.当乙醇、KBr和(NH_4)_2SO_4分别为体积分数30%、4.0×10~(-3)mol/J L、0.3 g,mL.pH 3时,Ir(Ⅳ)的萃取率达到99.5%以上,Ga(Ⅲ),Al(Ⅲ),Cr(Ⅲ),Mo(Ⅵ),Fe(Ⅲ),Ni(Ⅱ),Zn(Ⅱ),Co(Ⅱ),Mn(Ⅱ),V(Ⅴ),Ag(Ⅰ),Ru(Ⅲ)和Rh(Ⅲ)基本不被萃取,实现了Ir(Ⅳ)与上述金属离子的分离.     

用X光电子能谱研究铱催化剂的表面性质

用同一浸渍法但焙烧、还原条件不同制成了两种Ir-Al_2O_3催化剂,考察了浸渍、焙烧及还原后各样品的Ir_(4f),Al_(2p)N_(1s)的XPS谱图。表明在制备过程中[IrCl_6]~(-2)在Al_2O_3上为Ir(4),Ir(3),Ir(0)的物类,Ir的化学环境受处理条件的影响,通过用于肼分解反应后,Ir的状态组成无变化,但晶粒显著增大,并有氮残存在表面上。用Ir_(4f),与Al_(2p)谱线的强度比表示Ir的分散度与其它方法对比有一致性。     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.     

Cu0-catalysed 1,3-dipolar cycloadditions of α-amino acid derived N,N-cyclic azomethine imines to ynones

A series of 20 CuAIAC reactions between eight 4-acylamino substituted pyrazolidine-3-one-1-azomethine imines and four terminal ynones were performed using Cu⁰ as catalyst. The corresponding fluorescent cycloadducts were obtained in very high yields upon simple workup. Thus, Cu-metal turned out to be a better catalyst than Cu^I in terms of yield and ease of isolation. Availability of azomethine imines, mild reaction conditions, and simple workup enable a “click” access to libraries of densely substituted 2,3-dihydro-1H,5H-pyrazolo[1,2-a]pyrazol-1-ones. Reactivity of differently substituted dipoles was evaluated experimentally and by quantum chemical methods (DFT).