A high-throughput platform for low-volume high-temperature/pressure sealed vessel solvent extractions

A high-throughput platform for performing parallel solvent extractions in sealed HPLC/GC vials inside a microwave reactor is described. The system consist of a strongly microwave-absorbing silicon carbide plate with 20 cylindrical wells of appropriate dimensions to be fitted with standard HPLC/GC autosampler vials serving as extraction vessels. Due to the possibility of heating up to four heating platforms simultaneously (80 vials), efficient parallel analytical-scale solvent extractions can be performed using volumes of 0.5-1.5 mL at a maximum temperature/pressure limit of 200°C/20 bar. Since the extraction and subsequent analysis by either gas chromatography or liquid chromatography coupled with mass detection (GC-MS or LC-MS) is performed directly from the autosampler vial, errors caused by sample transfer can be minimized. The platform was evaluated for the extraction and quantification of caffeine from commercial coffee powders assessing different solvent types, extraction temperatures and times. For example, 141±11 μg caffeine (5 mg coffee powder) were extracted during a single extraction cycle using methanol as extraction solvent, whereas only 90±11 were obtained performing the extraction in methylene chloride, applying the same reaction conditions (90°C, 10 min). In multiple extraction experiments a total of ~150 μg caffeine was extracted from 5 mg commercial coffee powder. In addition to the quantitative caffeine determination, a comparative qualitative analysis of the liquid phase coffee extracts and the headspace volatiles was performed, placing special emphasis on headspace analysis using solid-phase microextraction (SPME) techniques. The miniaturized parallel extraction technique introduced herein allows solvent extractions to be performed at significantly expanded temperature/pressure limits and shortened extraction times, using standard HPLC autosampler vials as reaction vessels. Remarkable differences regarding peak pattern and main peaks were observed when low-temperature extraction (60°C) and high-temperature extraction (160°C) are compared prior to headspace-SPME-GC-MS performed in the same HPLC/GC vials.     

Simultaneous determination of monomethylmercury, monobutyltin, dibutyltin and tributyltin in environmental samples by multi-elemental-species-specific isotope dilution analysis using electron ionisation GC-MS

In this work, the simultaneous determination of four organometallic species (monomethylmercury, monobutyltin, dibutyltin and tributyltin) in environmental samples by using a GC-MS system with electron ionisation has been established. The measurement of isotope ratios in each species was accomplished by selecting the most adequate molecular cluster, and simple mathematical equations were applied to correct the contributions of 13C from the organic groups attached to the tin and mercury atoms. The influence of different parameters such as dwell time on the precision and accuracy of the measured isotope ratios in each target species has also been studied. The determination and the sample preparation procedures presented in this work were first individually validated by analysing several certified reference materials for butyltin compounds (mussel tissue CRM-477 and marine sediment SOPH-1) and for monomethylmercury (tuna fish CRM-464) using an innovative focused microwave technology for the extraction of the species from the solid samples. Additionally, the simultaneous determination of the four species was successfully validated by obtaining quantitative recoveries in spiked natural waters and by analysing the certified reference material BCR-710 (certified in tributyltin and monomethylmercury). The values obtained in such certified tissue were fully in agreement not only with the certified mass fractions but also with the proposed indicative values for mono- and dibutyltin.     

Tartaric acid extraction of organotin compounds from sediment samples

A new extraction method for the determination of tributyltin (TBT), dibutyltin (DBT) and monobutyltin (MBT) in sediments based on extraction with tartaric acid and methanol has been developed. Tin species were extracted from sediment samples using focused microwave technology, then ethylated with sodium tetraethylborate (NaBEt₄) and analyzed by isotope dilution (ID) gas chromatography-mass spectrometry (GC-MS). The advantages of such methodology in comparison with other established extraction methods for the routine speciation analysis of organotin compounds are discussed with respect to sulfur interferences co-extracted from complex matrices.Interferences from elemental sulfur are normally found with acetic acid extraction, but with tartaric acid extraction these interferences were eliminated, demonstrating selective extraction.The accuracy of the analytical procedure was established by analyzing a certified reference material (CRM) (PACS-2, marine sediment) and comparing the results to the certified values. Good agreement between determined and certified values for butyltin compounds was obtained. Finally, some complex sediment samples collected from San Vicente's Bay, Chile, were analyzed with the proposed methodology, demonstrating its potential value for monitoring butyltins in environmental samples with high concentrations of sulfur compounds.     

Is there a future for sequential chemical extraction?

Since their introduction in the late 1970s, sequential extraction procedures have experienced a rapid increase in use. They are now applied for a large number of potentially toxic elements in a wide range of sample types. This review uses evidence from the literature to consider the usefulness and limitations of sequential extraction and thereby to assess its future role in environmental chemical analysis. It is not the intention to provide a comprehensive survey of all applications of sequential extractions or to consider the merits and disadvantages of individual schemes. These aspects have been covered adequately in other, recent reviews. This review focuses in particular on various key issues surrounding sequential extractions such as nomenclature, methodologies, presentation of data and interpretation of data, and discusses typical applications from the recent literature for which sequential extraction can provide useful and meaningful information. Also covered are emerging developments such as accelerated procedures using ultrasound- or microwave energy-assisted extractions, dynamic extractions, the use of chemometrics, the combination of sequential extraction with isotope analysis, and the extension of the approach to non-traditional analytes such as arsenic, mercury, selenium and radionuclides.     

Focused-microwave-assisted strategies for sample preparation

In this work a general discussion is presented about extraction and digestion procedures, assisted by focused-microwave radiation. Applications involving inorganic, organic, and organometallic analytes in different types of samples are presented, taking into account recent literature data. The main advantages of using focused-microwave radiation are highlighted, such as safety, versatility, control of microwave energy released to the sample, and programmed addition of solutions. All these features can be applied properly in sample preparation for speciation analysis. New routes of development are discussed considering partial digestion by acid-vapor and gradual addition of a liquid sample to hot concentrated acids. Some preliminary results using these strategies are presented to demonstrate their potentiality.     

Determination of three capsaicinoids in Capsicum annuum by pressurized liquid extraction combined with LC‐MS/MS

A new method based on pressurized liquid extraction followed by LC‐MS/MS analysis has been developed for the identification and quantification of three capsaicinoids (capsaicin, dihydrocapsaicin, and nordihydrocapsaicin) in extracts of Capsicum annuum. For the recovery of three capsaicinoids, the efficiency levels of ultrasonic‐assisted extraction, microwave‐assisted extraction, Soxhlet extraction, and pressurized liquid extraction were compared under different conditions. Pressurized liquid extraction resulted in higher yields. Pressurized liquid extractions were performed using methanol; temperature was set at 100°C and pressure at 1500 psi. LC analysis was performed on a Waters XBridge? C₁₈ column (150 × 2.1 mm, id 3.5 μm) eluted by a mobile phase of 0.1% formic acid and ACN. Data acquisition was carried out in multiple reaction monitoring transitions mode, monitoring two‐reaction monitoring transitions to ensure an accurate identification of target compounds in the samples. The proposed method is rapid, simple, and could be utilized for the routine analysis of three capsaicinoids in C. annuum samples.     

Sample treatment in chromatography-based speciation of organometallic pollutants.

Speciation analysis is nowadays performed routinely in many laboratories to control the quality of the environment, food and health. Chemical speciation analyses generally include the study of different oxidation state of elements or individual organometallic compounds. The determination of the different chemical forms of elements is still an analytical challenge, since they are often unstable and concentrations in different matrices of interest are in the microg l(-1) or even in the ng l(-1) range (e.g., estuarine waters) or ng g(-1) in sediments and biological tissues. For this reason, sensitive and selective analytical atomic techniques are being used as available detectors for speciation, generally coupled with chromatography for the time-resolved introduction of analytes into the atomic spectrometer. The complexity of these instrumental couplings has a straightforward consequence on the duration of the analysis, but sample preparation to separate and transfer the chemical species present in the sample into a solution to be accepted readily by a chromatographic column is the more critical step of total analysis, and demands considerable operator skills and time cost. Traditionally, liquid-liquid extraction has been employed for sample treatment with serious disadvantages, such as consumption, disposal and long-term exposure to organic solvent. In addition, they are usually cumbersome and time-consuming. Therefore, the introduction of new reagents such as sodium tetraethylborate for the simultaneous derivatization of several elements has been proposed. Other possibilities are based in the implementation of techniques for efficient and accelerated isolation of species from the sample matrix. This is the case for microwave-assisted extraction, solid-phase extraction and microextraction, supercritical fluid extraction or pressurized liquid extraction, which offer new possibilities in species treatment, and the advantages of a drastic reduction of the extraction time and the embodiment into on-line flow analysis systems. This new generation of treatment techniques constitutes a good choice as fast extraction methods for feasible species-selective analysis of organometallic compounds under the picogram level, that can be used for national regulatory agencies, governmental and industrial quality control laboratories, and consequently, for manufacturers of analytical instrumentation.     

Application of microwave digestion to the preparation of sediment samples for arsenic speciation

Several extraction procedures are described allowing arsenic speciation in sediments. The extraction of organometallic compounds such as dimethylarsinic acid or monomethylarsonic acid is quite simple since these compounds are stable in the different extraction media (HCl/ HNO₃, H₃PO₄, ammonium oxalate) and are easily released independent of the extraction mode (magnetic stirring or microwave solubilization). Extraction yields are higher than 96% for these two arsenic forms. An HCl/HNO₃ microwave solubilization procedure allows the quantitative solubilization of mineral arsenic, but the differentiation between the two oxidation states is not possible owing to the oxidation of As(III) to As(V). Extractions with orthophosphoric acid or ammonium oxalate allow the solubilization of mineral arsenic with extraction yields ranging from 90 to 95% and the differentiation between As(III) and As(V). Nevertheless, the amount of As(III) is underestimated owing to its partial oxidation. The usefulness and advantages of microwave solubilization compared with conventional extraction procedures are discussed. Received: 17 May 1996 / Revised: 19 September 1996 / Accepted: 25 September 1996     

Application of microwave digestion to the preparation of sediment samples for arsenic speciation

Several extraction procedures are described allowing arsenic speciation in sediments. The extraction of organometallic compounds such as dimethylarsinic acid or monomethylarsonic acid is quite simple since these compounds are stable in the different extraction media (HCl/ HNO₃, H₃PO₄, ammonium oxalate) and are easily released independent of the extraction mode (magnetic stirring or microwave solubilization). Extraction yields are higher than 96% for these two arsenic forms. An HCl/HNO₃ microwave solubilization procedure allows the quantitative solubilization of mineral arsenic, but the differentiation between the two oxidation states is not possible owing to the oxidation of As(III) to As(V). Extractions with orthophosphoric acid or ammonium oxalate allow the solubilization of mineral arsenic with extraction yields ranging from 90 to 95% and the differentiation between As(III) and As(V). Nevertheless, the amount of As(III) is underestimated owing to its partial oxidation. The usefulness and advantages of microwave solubilization compared with conventional extraction procedures are discussed. Received: 17 May 1996 / Revised: 19 September 1996 / Accepted: 25 September 1996     

Analysis of volatiles in polymers,part II. Supercritical fluid extraction/open tubular GC/MS

Summary Supercritical fluid extraction (SFE) connected to open tubular gas chromatography has been used for the analysis of non-polar to medium polar volatiles entrained in polymers. This polymer sheets, prepared with the aid of a microtome, have been extracted with supercritical carbon dioxide. The influence of sample area/weight ratio and extraction cell volume on the SFE performance has been investigated. Further, quantitative analysis was executed by stepwise extractions.A set of polybutylene terephthalate polymers, originating from different manufactures, has been analysed regarding entrained volatiles.     

A gas chromatographic assay for quantitative analysis of volatiles in solid materials by discontinuous gas extraction

Summary A method has been developed for the quantitative analysis of volatile compounds in solid samples. The method is based on a stepwise gas extraction of the volatiles with subsequent analysis of the extracted material and is termed discontinuous gas extraction. Any quantitative analysis requires an exhaustive extraction, which, however, is often too time-consuming for routine analysis. It is shown how the total amount of each volatile compound can be calculated from only a few extractions. Such a calculation is possible because for analytical purposes it is the information of the extraction process and not the extracted material that is needed. This method is useful for samples which are insoluble, such as certain polymers or residual solvents in printed foils, and which cannot be analyzed quantitatively by headspace gas chromatography, since no calibration solution can be prepared. It is further shown how discontinuous gas extraction can also be used to calibrate headspace analysis. Thus, both methods combine well together in that discontinuous gas extraction provides the accuracy while the headspace analysis gives convenience and speed of sample throughput, particularly if carried out with an automated headspace analyzer.     

Extraction of cations as salts of fatty acids : Analytical and chromatographic separation of beryllium from iron and aluminium

Quantitative extractions of aluminium and ferric ions are carried out in presence of butyric acid. A method has been given for quantitative extraction of beryllium from aluminium and ferric ion in presence of ethylenediaminetetra-acetic acid. Interference has been studied and interference due to phosphate has been avoided by addition of zirconium salt. The method has been applied to thc analysis of beryl.     

The Chemistry of Separations Ligand Degradation by Organic Radical Cations

Solvent based extractions of used nuclear fuel use designer ligands in an organic phase extracting ligand complexed metal ions from an acidic aqueous phase. These extractions will be performed in highly radioactive environments, and the radiation chemistry of all these complexants and their diluents will play a major role in determining extraction efficiency, separation factors, and solvent-recycle longevity. Although there has been considerable effort in investigating ligand damage occurring in acidic water radiolysis conditions, only minimal fundamental kinetic and mechanistic data has been reported for the degradation of extraction ligands in the organic phase. Extraction solvent phases typically use normal alkanes such as dodecane, TPH, and kerosene as diluents. The radiolysis of such diluents produce a mixture of radical cations (R^•+), carbon-centered radicals (R^•), solvated electrons, and molecular products such as hydrogen. Typically, the radical species will preferentially react with the dissolved oxygen present to produce relatively inert peroxyl radicals. This isolates the alkane radical cation species, R^•+ as the major radiolytically-induced organic species that can react with, and degrade, extraction agents in this phase. Here we report on our recent studies of organic radical cation reactions with various ligands. Elucidating these parameters, and combining them with the known acidic aqueous phase chemistry, will allow a full, fundamental, understanding of the impact of radiation on solvent extraction based separation processes to be achieved.     

Cold vapour atomic fluorescence spectrometry and gas chromatography-pyrolysis-atomic fluorescence spectrometry for routine determination of total and organometallic mercury in food samples

Two procedures have been investigated for the quantification of the different forms of mercury in food. A two-stage procedure has been developed to determine firstly total inorganic and organometallic species, and then the full separation of all organomercury species. The procedure involves solubilisation of the samples using alkaline extractions or enzymolysis, followed by the extraction of organic mercury in an organic solvent, preferably a mixture of dichloromethane and hexane (3:2). For the total organic mercury determination, the organic extract is analysed for "total" mercury after nitric acid/peroxide digestion, evaporation of the solvent and detection by cold vapour-atomic fluorescence spectrometry. Full organomercury speciation requires a clean-up step before analysis of the final extract in dichloromethane by gas chromatography coupled to a pyrolyser and an atomic fluorescence detector (GC-pyro-AFS). A detection limit of 6 ng l-1, and reproducibility of 2% was achieved for the CV-AFS method; GC-pyro-AFS yielded 200 ng l-1 and 5% for detection limit and coefficient of variation, respectively. Both procedures were validated with the use of various certified reference materials over a wide range of mercury concentrations, and by spiking experiments. The validated methods were tested successfully on a wide range of commercially available food samples.     

Metal fractionation in olive oil and urban sewage sludges using the three-stage BCR sequential extraction method and microwave single extractions

The conventional three-stage BCR sequential extraction method was employed for the fractionation of heavy metals in sewage sludge samples from an urban wastewater treatment plant and from an olive oil factory. The results obtained for Cu, Cr, Ni, Pb and Zn in these samples were compared with those attained by a simplified extraction procedure based on microwave single extractions and using the same reagents as employed in each individual BCR fraction. The microwave operating conditions in the single extractions (heating time and power) were optimized for all the metals studied in order to achieve an extraction efficiency similar to that of the conventional BCR procedure. The measurement of metals in the extracts was carried out by flame atomic absorption spectrometry. The results obtained in the first and third fractions by the proposed procedure were, for all metals, in good agreement with those obtained using the BCR sequential method. Although in the reducible fraction the extraction efficiency of the accelerated procedure was inferior to that of the conventional method, the overall metals leached by both microwave single and sequential extractions were basically the same (recoveries between 90.09 and 103.7%), except for Zn in urban sewage sludges where an extraction efficiency of 87% was achieved. Chemometric analysis showed a good correlation between the results given by the two extraction methodologies compared. The application of the proposed approach to a certified reference material (CRM-601) also provided satisfactory results in the first and third fractions, as it was observed for the sludge samples analysed.     

Systematic Investigations of Plastic Vials Concerning Their Suitability for Ultratrace Anion Analysis in High-Purity Industrial Applications

Ultratrace anion analysis in high-purity industrial applications is done using commercially available plastic vials to store the eluted liquid samples. Plastic vials are manufactured with materials containing several additives. Such additives might potentially release anionic contaminants, thus degrading the blank quality and determination limits (DL). The durability and thermal stability of several materials was found to be a function of anionic species. Fluorinated materials showed the best results for the majority of anions with the exception of fluoride. For the selective analysis of fluoride, polypropylene was found to be the best vial material, together with glass. Cold water extraction showed better results compared to hot water extraction. Over a long observation period, hot water extraction did not at all improve the performance, indicating that this type of supposedly efficient cleaning of the plastic containers to render them less prone to contaminant release does not hold true.     

Automated high-capacity sorption probe for extraction of organic compounds in aqueous samples followed by gas chromatographic analysis

An automated high-capacity sorption device for GC analysis of ultra trace components has been developed. The scope of the presented technique was to combine the simplicity of solid-phase microextraction (SPME) with the high extraction efficiency of the stir bar sorptive extraction technology. Sorptive extractions of water samples were performed using polydimethylsiloxane (PDMS) rubber tubing (120 microl) mounted onto a glass rod. The sampling procedure was carried out by a robotic autoinjector. Since the setup is fully automated, unattended and precise time-controlled extraction of samples is possible and makes quantitation with non-equilibrium extractions feasible. The sorption probes are easy to exchange, which facilitates off-line/in-field sampling. The system was evaluated with a test mixture of 44 environmentally hazardous compounds. Detection limits were found to be in the sub-ppt region. The performance of the system was demonstrated with the analysis of polycyclic aromatic hydrocarbons in urban snow.     

Analysis of the kinetic stability of yttrium chelates by free-ion selective radiotracer extraction (FISRE)

Within this work the analysis of the kinetic stability of a series of yttrium complexes, i.e., Y-citrate, Y-NTA, Y-CDTA as well as Y-humic acid (Y-HA) has been successfully performed by the free-ion selective radiotracer extraction (FISRE) method. FISRE uses ⁹⁰Y with a high specific activity to perform CHELEX extractions in a buffered aqueous solution at pH 6 in two different modes by monitoring the dissociation and association reactions of the corresponding complexes. Whereas in the case of Y-citrate the dissociation profile could be successfully described in terms of (pseudo) first order kinetics, the other complexes tend to form two species with different kinetic properties, although only one species is predicted by speciation calculations. In the batch FISRE method, all (except Y-NTA) corresponding association rate constants were determined by monitoring the formation rate of the yttrium complexes.     

Low volume microwave digestion for the determination of selenium in marine biological tissues by graphite furnace atomic absorption spectroscopy

A microwave digestion method for the determination of marine biological tissues has been developed to allow determination of selenium in small sample sizes (< 0.1 g). The benefits of this technique include maintaining concentrates in extracts without the subsequent over dilution encountered when using larger vessels, increased sample throughput and reduced loss of volatile material. Freeze dried biological material (< 0.1 g) and nitric acid (1 ml) were placed into 7 ml screw top Teflon vessels which are completely sealed on capping. Two 7 ml vials were placed into larger 120 ml vessels fitted with a Teflon spacer and 10 ml of distilled water. The effects of microwave power and time, and sample mass on selenium recovery from three marine standard reference materials (NIST SRM 1566a Oyster Tissue, NRCC DORM-1 Dogfish Muscle and NRCC TORT-1 Lobster Hepatopancreas) were examined. The optimum conditions: 600 W, 2 min; 0 W, 2 min; 450 W, 45 min, allowed quantitative recoveries of selenium from these and three other standard reference materials (NRCC DOLT-1 Dogfish liver, NIST RM-50 Albacore tuna and IAEA MA-A-2 fish flesh). Studies on sample mass showed that the analysis of sample masses from 0.025 to 0.1 g gave selenium concentrations within the certified range. Six species of selenium: selenite, selenate, selenomethionine, selenocysteine, selenocystamine, and trimethyl selenonium were added to oyster, dogfish, and lobster tissues. Recoveries were near quantitative for all species (94–105%) except trimethyl selenonium (90–101%).     

Enzyme-assisted extraction of arsenic species from plant material

Investigations regarding the transfer and metabolism of arsenic species in plants require mild extraction conditions to conserve the original composition of arsenic species. Beside the use of water or water/methanol for extraction of arsenic species from plant samples, enzymes can assist this procedure by digestion of cellulose and other constituents of cell walls, resulting in a faster, more efficient extraction technique which preserves the arsenic species. The investigations presented here were focused on the stability of certain arsenic species in enzymatic solutions, optimal conditions for their chromatographic separation and detection namely by means of ion chromatography–inductively coupled plasma mass spectrometry and improvements with respect to extraction efficiency. With commercially available enzymes and enzyme mixtures, the digestion rate of soluble starch as model cellulose was determined using high-performance anion exchange chromatography–pulsed amperometric detection analysis of glucose as the major digestion product. The most effective digestion rate (80% within 4?h) was obtained with Viscozyme®. This enzyme mixture was applied to extracted arsenic species from algae and terrestrial plant materials. Qualitative and quantitative differences in the results between enzyme-assisted and water extractions were obtained and discussed. The results show that the application of enzymes in mild extraction protocols should be evaluated as an additional step for the identification of As-metabolics in organisms. Careful selection of suitable enzyme mixtures can overcome the disadvantage that extraction efficiency is very organism-specific.