Preparation of polyamide-imides via the phosphorylation reaction. II. Synthesis of wholly aromatic polyamide-imides from N-[p-(or m-) carboxyphenyl]trimellitimides and various aromatic diamines

Wholly aromatic polyamide-imides with high molecular weight (η_inh up to 1.7 dL/g in DMAc–5% LiCl) were obtained by the direct polycondensation reaction of N-[p-( or m-) carboxyphenyl]trimellitimide [p-(or m-)CPTMI] and aromatic diamines by means of di- or triphenyl phosphite in N-methyl-2-pyrrolidone (NMP)-pyridine solution in the presence of lithium or calcium chloride. The factors affecting the phosphorylation reaction were investigated, in particular for the reaction of p-CPTMI and 4,4'-oxydianiline (ODA). Molecular weight of polymers varied with the amount of metal salts and showed maximum values at the concentration of 10-15 wt % in the reaction mixture. Monomer concentration of 0.2 mol/L produced polymer of the highest viscosity. Higher concentrations produced gelation and yielded polymers of low molecular weight. A reaction temperature of about 120°C gave the best results. Among the solvents tested, NMP was significantly the most effective for the reaction. The highest inherent viscosity values, η_inh = 1.35 and 1.58 dL/g, were obtained with triphenyl phosphite (TPP)/monomer and diphenyl phosphite (DPP)/monomer molar ratios of 2.0. Excessive addition of phosphites did not cause a serious deleterious effect on the molecular weight of polymer. Polycondensations of several combinations of p-or m-CPTMI and aromatic diamines were carried out with satisfactory results.     

High-molecular-weight poly(p-phenyleneterephthalamide) by the direct polycondensation reaction with triphenyl phosphite

Poly(p-phenyleneterephthalamide) of high molecular weight was obtained when the polycondensation of terephthalic acid and p-phenylenediamine was carried out in N-methylpyrrolidone (NMP) that contained dissolved CaCl₂ and LiCl in the presence of pyridine. The molecular weight of the polymer obtained varied with the amount of pyridine relative to the metal salts and with the molar ratios of CaCl₂ to LiCl, the maximum η_inh value of 4.5 being obtained under the conditions Py/(CaCl₂ + LiCl) ≈ 2.5 (mol/mol), CaCl₂/LiCl ≈ 1.2 (mol/mol), and LiCl + CaCl₂ ≈ 4 g. Among the solvents tested, NMP was significantly effective for the reaction. Polycondensations of several combinations of other dicarboxylic acids and diamines were carried out with limited success.     

Studies on reactions of the N-phosphonium salts of pyridines. XIV. Wholly aromatic polyamides by the direct polycondensation reaction by using phosphites in the presence of metal salts

Poly-p-benzamide of high molecular weight (η_inh = ～ in H₂SO₄) was obtained by the direct polycondensation reaction of p-aminobenzoic acid (p-ABA) by means of diphenyl and triaryl phosphites in N-methylpyrrolidone (NMP)-pyridine solution containing lithium and calcium chlorides. Molecular weight of polymer varied with the amount of these salts, showing maximum values at the concentration of about 4 wt-% of LiCl or about 8 wt-% of CaCl₂ in the reaction mixture. The reaction temperature at around 80°C gave a polymer of the highest viscosity. The polycondensation reaction was also affected by monomer concentration, solvents, and tertiary amines like pyridine. Similarly, aromatic polyamides with high molecular weight (η_inh values up to 1.34 in H₂SO₄) were prepared from isophthalic acid and aromatic diamines, whereas terephthalic acid gave only low-viscosity polymers.     

Direct polyesterification promoted by a complex of phosphorus oxychloride with LiCl monohydrate

The reaction of benzoic acid and p-chlorophenol with phosphorus oxychloride (POC) was significantly affected by the presence of metal salt hydrates or a mixture of metal salts and water sufficiently aged. Among metal salts examined, LiCl was most effective for the reaction to give quantitative yield of the benzoate. The reaction was assumed to proceed via a complexation of POC with LiCl monohydrate followed by selective hydrolysis of POC by water bound to LiCl. The reaction promoted by a complex derived from POC and LiCl monohydrate in pyridine was successfully used as a new condensing agent for the synthesis of aromatic polyesters by the direct polycondensation or aromatic dicarboxylic acids and bisphenols. Under favorable conditions for aging of POC with LiCl monohydrate and for addition of bisphenols, polymers of moderate to high molecular weights were obtained in quantitative yield. The reaction was applied with limited success to the preparation of a copolymer of high molecular weight from hydroxybenzoic acids.     

Preparation and Characterization of New Optically Active Poly(amide-imide)s from N,N′-(bicyclo[2,2,2]oct-7-ene-2,3,5,6-tetra carboxylic)-bis-L-isoleucine and Aromatic Diamines

Five new optically active aromatic poly(amide-imide)s (PAIs) 5a–e were prepared from a direct polycondensation reaction of a new diacid of N,N′-(bicyclo[2,2,2]oct-7-ene-2,3,5,6-tetra carboxylic)-bis-L-isoleucine 3 with various aromatic diamines 4a–e in a medium consisting of triphenyl phosphite (TPP), calcium chloride (CaCl₂), pyridine (Py) and N-methyl-2-pyrrolidone (NMP). The polycondensation reaction produced a series of novel poly(amid-imide)s 5a–e in quantitative yields with inherent viscosities of 0.39–0.51 dL/g. The resulting polymers were fully characterized by means of ¹H-NMR, FT-IR spectroscopy, elemental analyses, inherent viscosity, solubility test, specific rotation and thermal properties of them were investigated using TGA/DTG and differential scanning calorimeter (DSC). The diacid 4 was synthesized by the condensation reaction of bicyclo[2,2,2]oct-7-ene-2,3,5,6- tetracarboxylic dianhydride 1 with L-isoleucine 2 in acetic acid solution.     

Thermotropic copolyesters of a series of aromatic diols with phenylterephthalic acid and 4,4′-oxybisbenzoic acid

Wholly aromatic, liquid crystalline, main chain copolyesters derived from various linearly substituted aromatic diols with mixtures of 2-phenylterephthalic acid and a nonlinear aromatic dicarboxylic acid, 4,4′-oxybisbenzoic acid, were prepared by acidolysis condensation polymerization reactions and characterized for their liquid crystalline properties. The formation of a liquid crystalline phase at elevated temperatures was not prevented by the introduction of up to 50 mol % of the nonlinear diacid in the copolymers, and all of those copolyesters exhibited nematic liquid crystalline phases. Furthermore, the inclusion of a nonlinear monomer was not as effective as was the presence of a phenyl substituent in decreasing the melting transition of these copolymers. All of the copolymers had high glass transition temperatures and high thermal stabilities. © 1993 John Wiley & Sons, Inc.     

Regular Copolyamides. III. Preparation and Characterization of Regular Aliphatic/Aromatic Copolyoxamides

Regular aliphatic/aromatic copolyoxamides were prepared from diamine-oxamides and aromatic diacid chlorides by interfacial and solution polymerization. Solution polymerization in chloroform or dimethylacetamide is preferred for the preparation of large quantities of polymers but interfacial polymerization is most conveniently carried out for the preparation of polymers with high molecular weight. Aromatic diacid chlorides used included the diacid chlorides of terephthalic acid, isophthalic acid, 2,6-pyridinedicarboxylic acid, two isomeric naphthalene dicarboxylic acids, two cyclo-hexanedicarboxylic acid isomers, as well as 1,1-cyclobutane-dicarboxylic acid. Copolymers of diamine-oxamides with mixtures of acid chlorides of isophthalic and pyridine dicarboxylic acid and isophthalic acid/tetrachloroterephthalic acid have also been prepared. Most polymers are film-forming and are soluble in concentrated sulfuric acid, trifluoroacetic acid, and dimethylacetamide (containing several per cent LiCl). A number of these polymers gave dense or asymmetric membranes, particularly the polymers from ethylene diamine as the aliphatic diamine, particularly poly(iminoethyleneimino-oxalyliminoethyleneiminoisophthaloyl) (p-222I). Diamine oxamides with more than two amide groups in the molecules have been prepared, and in one case polymers with aromatic diacid chlorides have been prepared by interfacial polymerization. All regular aliphatic/aromatic copolyoxamides are high-melting and generally decompose above 350°C without melting. They can, however, be fabricated from solution into brittle fibers or into desalination membranes.     

Investigation and radiometric determination of saturated and unsaturated aliphatic monocarboxylic acids and aromatic dicarboxylic acids

Investigations have been carried out on the precipitation of calcium salts of saturated and unsaturated aliphatic monocarboxylic acids and of aromatic dicarboxylic acids. The optimum ethanol/water solvent ratio has been studied at which the sodium, ammonium or triethylammonium salts of the acids have a good solubility, whereas the calcium salts are poorly soluble and can be precipitated. Based on these investigations the radiometric determination of formic acid, palmitic acid, stearic acid, methacrylic acid, oleic acid, and o-, m- and p-phthalic acids has become possible. A linear correlation has been found between the solubilities of the calcium salts of o-, m- and p-phthalic acids and the dielectric constant of the solvent mixture. CaCl₂ solution labelled with⁴⁵CaCl₂ was used for the titrations, with a solvent composition identical to that of the solution to be titrated. Radiometric titrations were carried out in 0.05M solutions for dicarboxylic acids, and in 0.1M solutions for monocarboxylic acids. For palmitic and stearic acids titrations were also carried out in the 0.01M concentration range. The equipment used for titrations was capable of detecting isotopes of soft β-radiation.     

Novel polyesters and polyester/Cloisite 30B nanocomposites based on a new rhodanine-based monomer

A novel bis-diol monomer, 3,3'-bis-(2-hydroxyethyl)-2,2'-dithioxo-[5,5']bithiazolidinylidene-4,4'-dione, was prepared in a one-pot three component reaction and used in a polyesterification reaction with various aromatic dicarboxylic acids using tosyl chloride/dimethylformamide/pyridine system as a condensing agent in order to generate a series of new polyesters. The prepared polyesters were characterized by FTIR spectroscopy and elemental analysis. In the next part, a series of polyester/clay nanocomposites were synthesized through a polyesterification reaction of the synthesized monomer with iso-phthalic acid. Cloisite 30B was used as the filler at different concentrations. Wide-angle X-ray diffraction and transmission electron microscopy studies showed that the organoclay layers are mainly exfoliated in the nanocomposites containing 1 wt % of Cloisite 30B.     

Preparation of polyamides via the phosphorylation reaction. X. A study of higashi reaction conditions

We report a study of the conditions of the phosphorylation reaction for the preparation of aromatic polyamides using the Higashi reaction medium. For poly(p-phenylene terephthalamide) (PPD-T), the optimum conditions are: reaction temperature, 115°C; monomer concentration, C = 0.083 mol/L; and ratio of triphenyl phosphite (TPP) to monomer, 2.0. These optimum conditions produce PPD-T having η_inh = 6.2 dL/g. At temperatures of 120°C and above PPD-T precipitates from the reaction mixture, leading to lower molecular weights. At lower temperatures the reaction mixture gels, and the gel time decreases with increasing reaction temperature. However, polycondensation continues in the gel state. Monomer concentrations C = 0.10 mol/L and above produce precipitation and yield polyamides of lower molecular weight. For the preparation of poly(p-benzamide) (PBA), the optimum ratio of TPP to monomer is 0.6 for either p- aminobenzoic acid or N-4-(4′-aminobenzamido)benzoic acid. In the former case the inherent viscosity of polymer prepared at 115°C showed little dependence upon the concentration of the monomer. The highest value, η_inh = 1.8 dL/g, was obtained with C = 0.40 mol/L and a TPP/monomer ratio of 0.6. However, for the same TPP/monomer ratio, the monomer containing a preformed amide linkage, N-4-(4′-aminobenzamido)benzoic acid, gave PBA with η_inh = 4.6 dL/g when the monomer concentration is 0.33 mol/L. This is the highest value reported for PBA using the phosphorylation reaction. In A?A + B?B polycondensation, examples in which one of the monomers contained one or two preformed amide linkages produced polyamides having η_inh = 7.8 and 8.9 dL/g, respectively.     

Ionic liquids as novel solvents and catalysts for the direct polycondensation of N,N′‐(4,4′‐oxydiphthaloyl)‐bis‐L‐phenylalanine diacid with various aromatic diamines

Ionic liquids (ILs) are often considered green solvents capable of replacing traditional organic solvents and have been extensively studied in materials chemistry and catalysis. In this study, the direct polycondensation of N,N′‐(4,4′‐oxydiphthaloyl)‐bis‐L ‐phenylalanine diacid with various aromatic diamines was performed in IL media. The influence of various reaction parameters, including the nature of the IL cations and anions, the monomer structures, the reaction temperature, and the reaction time, on the yields and inherent viscosities of the resulting optically active poly(amide imide)s (PAIs) were investigated. Direct polycondensation successfully preceded in ILs and triphenyl phosphite (a condensing agent) without any additional extra components, such as LiCl and pyridine, which are used in similar reactions in ordinary molecular solvents. Therefore, ILs can act as both solvents and catalysts. Various high‐molecular‐weight, optically active PAIs were obtained in high yields with inherent viscosities ranging from 0.54 to 0.88 dL/g. This method was also compared with three other classical methods for the polycondensation of the aforementioned monomers. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 6545–6553, 2005     

Polymers containing quaternary ammonium groups based on poly(N-vinylimidazole)

A poly(N-vinylimidazole) (PNVI)—based poly(carboxybetaine) with two methylene groups between the opposite charges was achieved by the nucleophilic addition reaction of the mentioned aminic polymer to the carbon-carbon double bond of acrylic acid (AA). Treatment of poly(carboxybetaine) with concentrated HCl (2 N) for long time leads to the corresponding cationic polyelectrolyte. The poly(carboxybetaine) is soluble in both water and aqueous solutions of salts such as: LiCl, NaCl, NaHCO₃, CaCl₂, Na₂SO₄. In water and in the first three salts, poly(carboxybetaine) exhibits a non-polyelectrolyte behaviour (a linear dependence of reduced viscosities on polymer or salt concentration), while in the remaining two salts, a slight polyelectrolyte behaviour is observed. The cationic polyelectrolyte is soluble in water and aqueous solutions of LiCl, NaCl, CaCl₂ and NaHCO₃, except Na₂SO₄. It has a polyelectrolyte behaviour in all solutions. Also, the binding trends of the added salts by polymers are discussed.     

Synthesis and properties of aromatic polyamides derived from 1,6-bis(4-aminophenoxy)naphthalene and aromatic dicarboxylic acids

A new bis(phenoxy)naphthalene-containing diamine, 1,6-bis(4-aminophenoxy)naphthalene, was synthesized in two steps from the condensation of 1,6-dihydroxynaphthalene with p-chloronitrobenzene in the presence of potassium carbonate, giving 1,6-bis(4-nitrophenoxv)naphthalene, followed by hydrazine hydrate/Pd—C reduction. A series of polyamides were synthesized by the direct polycondensation of the diamine with various aromatic dicarboxylic acids in the N-methyl-2-pyrrolidone (NMP) solution containing dissolved metal salts such as CaCl₂ or LiBr using triphenyl phosphite and pyridine as condensing agents. The polymers were obtained in quantitative yield with inherent viscosities of 0.78–3.72 dL/g. Most of the polymers were soluble in aprotic solvents such as N,N-dimethylacetamide (DMAc), N,N-dimethylformamide (DMF), NMP, and they could be solution-cast into transparent, flexible and tough films. The casting films had tensile strength of 102–175 MPa, elongation at break of 8–42%, and tensile modulus of 2.4–3.8 GPa. The polymers derived from rigid dicarboxylic acids such as terephthalic acid and 4,4′-biphenyldicarboxylic acid exhibited some crystalline characteristics. The glass transition temperatures of the polyamides were in the range of 238–337°C, and their 10% weight loss temperatures were above 487°C in nitrogen and above 438°C in air. © 1995 John Wiley & Sons, Inc.     

Polymerization of acrylamide in various solvents in the presence of Lewis acids

The radical polymerization of acrylamide in various solvents in the presence of Lewis acids has been investigated. Considerable effects of LiBr, LiCl and CaCl₂ on the total reaction rate and the values of k_p and k₁ for polymerization in DMSO or THF have been shown. For the polymerization of acrylamide in aqueous solution, addition of the salts does not affect the kinetic behaviour of the process. The observed effect of salts arises from complexation between the salt and the monomer and/or the propagating radicals.     

Synthesis of high-molecular-weight poly(amide-ester)s by direct polycondensation with diphenyl chlorophosphate

High molecular weight aromatic poly(amide-ester)s were prepared by the direct polycondensation reactions between aromatic dicarboxylic acids and aminophenols under mild conditions in pyridine. The condensing agents examined in this study were diphenyl chlorophosphate (DPCP), DPCP/LiCl, and DPCP/DMF. Addition time of the aminophenols, depending on their nucleophilicities, affected the η_inh values and monomer sequence of the resulting polymer. Their thermal properties were studied in terms of the sequences in the polymer backbones.     

Microwave‐assisted synthesis of optically active poly(amide imide)s derived from diacid chloride containing epiclon and L‐leucine with aromatic diamines

Epiclon [3a,4,5,7a‐tetrahydro‐7‐methyl‐5‐(tetrahydro‐2,5‐dioxo‐3‐furanyl)‐1,3‐isobenzofurandione or 5‐(2,5‐dioxotetrahydrofurfuryl)‐3‐methyl‐3‐cyclohexyl‐1,2‐dicarboxylic acid anhydride] was reacted with L ‐leucine in acetic acid, and the resulting imide acid ( 3 ) was obtained in a high yield. The diacid chloride ( 4 ) was obtained from its diacid derivative 3 by a reaction with oxalyl chloride in dry carbon tetrachloride. The polycondensation reaction of 4 with several aromatic diamines, such as 4,4′‐sulfonyldianiline, 4,4′‐diaminodiphenylmethane, 4,4′‐diaminodiphenylether, p‐phenylenediamine, m‐phenylenediamine, 2,4‐diaminotoluene, and 1,5‐diaminonaphthalene, was developed with a domestic microwave oven in the presence of a small amount of a polar organic medium such as N‐methylpyrrolidone. The polymerization reactions were also performed with two other methods: low‐temperature solution polycondensation in the presence of trimethylsilyl chloride and reflux conditions. A series of optically active poly(amide imide)s with moderate yields and inherent viscosities of 0.12–0.19 dL/g were obtained. All of these polymers were fully characterized by IR, elemental analysis, and specific rotation techniques. Some structural characterizations and physical properties of these optically active poly(amide imide)s are reported. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1077–1090, 2003     

Wholly aromatic chiral polyamides bearing pendant phthalimido and L-isoleucine moities

<正>A potential biodegradable and optically active bulky chiral aromatic amide-imidic diacid monomer,(2S,3S)-5-(3- methyl-2-phthalimidylpentanoylarnino)isophthalic acid(7),containing a rigid phthalimide and flexible L-isoleucine pendant group was synthesized in three steps.New aromatic polyamides including pendant phthalimido groups and flexible side spacers have been synthesized by direct polycondensation reaction of equimolar amounts of different aromatic diamines with an optically active diacid 7,using N-methyl-2-pyrrolidone(NMP) as a solvent and triphenyl phosphite/CaCl_2/pyridine as a condensing agent.These polyamides were characterized by FTIR,~1H-NMR spectroscopy,specific rotation, thermogravimetric and elemental analysis.The resulting polymers have inherent viscosities in the range of 0.21-0.45 dL/g. Amino acid existence in this backbone results in optically active polymers.Due to introduction of bulky and flexible groups in these polyamides,they show improved solubility in polar aprotic solvents such as NMP and dimethylacetamide and also good thermal stability(10%weight loss temperatures in excess of 330℃,and char yields at 600℃in nitrogen higher than 62%).     

Polysilylether: A Degradable Polymer from Biorenewable Feedstocks

The synthesis of polysilylethers (PSEs) using a monomer derived from a biorenewable feedstock is reported. The AB‐type monomer was synthesized from undecenoic acid through hydrosilylation and reduction, and the polymerization was catalyzed by earth‐abundant metal salts. High‐molar‐mass products were achieved, and the degree of polymerization was controlled by varying the amount of an AA‐type monomer in the reaction. The PSEs possess good thermal stability and a low glass‐transition temperature (T_g≈?67 °C). To demonstrate the utility of the PSEs, polyurethanes were synthesized from low‐molar‐mass hydroxy‐telechelic PSEs.     

New poly(amide-imide)s syntheses. I. Soluble high-temperature poly(amide-imide)s derived from 2,5-bis(4-trimellitimidophenyl)-3,4-diphenylthiophene and various aromatic diamines

Novel aromatic poly(amide-imide)s with high inherent viscosities were prepared by direct polycondensation reaction of 2,5-bis(4-trimellitimidophenyl)-3,4-diphenylthiophene ( IV ) and aromatic diamines using triphenyl phosphite in the N-methyl–2-pyrrolidone (NMP)/pyridine solution containing dissolved CaCl₂. The diimide-diacid IV was readily obtained by the condensation reaction of 2,5-bis(4-aminophenyl)-3,4-diphenylthiophene ( III ₁) with trimellitic anhydride. The obtained poly(amide-imide)s showed high thermostability. Their decomposition temperatures at 10% weight loss in nitrogen atmospheres were above 550°C and the anaerobic char yield at 800°C ranged from 48 to 68%. Almost all the poly(amide-imide)s showed high glass transition temperatures above 300°C by differential scanning calorimetry (DSC) measurements. These polymers were readily soluble in various organic solvents and could be cast into transparent, tough, and flexible films. Their casting films showed obvious yield points in the stress-strain curves and had strength at break up to 74.2 MPa, elongation to break up to 70.1%, and initial modulus up to 4.56 GPa. The factors affecting the reaction of diimide-diacid IV and 4,4′-oxydianiline in view of monomer concentration, reaction temperature, and amount of CaCl₂ were also investigated. © 1992 John Wiley & Sons, Inc.     

Fully aromatic thermotropic liquid crystalline polyesters of 3,4′-dihydroxybenzophenone

A series of fully aromatic, thermotropic polyesters, derived from 3,4′-dihydroxybenzophenone and various aromatic dicarboxylic acids, was prepared by the high-temperature solution polycondensation method and examined for thermotropic behavior by a variety of experimental techniques. The aromatic dicarboxylic acids used in this study were 2,6-naphthalenedicarboxylic acid, 4,4′-bibenzoic acid, and terephthalic acid. The two homopolymers of 3,4′-DHB with either 2,6-NDA or 4,4′-BBA formed nematic LC phases at 285°C and 255°C and also exhibited isotropization transitions (T_i) at 317°C and 339°C, respectively. The copolymer of 3,4′-DHB with 50% TA and 50% 2,6-NDA also formed a nematic LC phase and had a broader range of LC phase than that of its respective homopolymers. Two other copolymers of 3,4′-DHB, both containing 50% 4,4′-BBA, also formed nematic LC phases at low T_f values. All of the thermotropic polyesters had high thermal stabilities. © 1994 John Wiley & Sons, Inc.