Semi-Preparative High-Performance Liquid Chromatographic Separation of Potato Glycoalkaloids

Abstract

A semi-preparative high-performance liquid chromatographic method has been developed to separate crude mixtures of the potato glycoalkaloids α-chaconine, α-solanine, commersonine and demissine. Milligram quantities of each substance can be obtained within an 8 hour period. A Zorbax semi-preparative NH₂ column and a solvent system of tetrahydrofuran-water-acetonitrile (55:20:25) were employed for the separation. The flow rate was 1.0 ml/min. Glycoalkaloid separations were monitored using both refractive index and ultraviolet detection (215 nm). Further analyses of these glycoalkaloids were done using analytical high-performance liquid chromatography (HPLC) and thin-layer chromatography (TLC) to check compound purity and identity.     

Influence of chamber saturation in thin-layer chromatography on theoretical and experimental parameters of mixture separations

The influence of chamber saturation in thin-layer chromatography on theoretical and experimental parameters of mixture separations were examined. Five different types of chambers for development of chromatograms were taken into consideration. The relation found experimentally differed widely from that calculated using O?cik's equation for different method of carrying out of the chromatographic process. The investigations presented here show the possibility of choosing chromatographic chambers which are optimum for theoretical studies on the process of thin-layer chromatography.     

Comparison of ultra high performance supercritical fluid chromatography,ultra high performance liquid chromatography,and gas chromatography for the separation of synthetic cathinones

A comparison of ultra high performance supercritical fluid chromatography, ultra high performance liquid chromatography, and gas chromatography for the separation of synthetic cathinones has been conducted. Nine different mixtures of bath salts were analyzed in this study. The three different chromatographic techniques were examined using a general set of controlled synthetic cathinones as well as a variety of other synthetic cathinones that exist as positional isomers. Overall 35 different synthetic cathinones were analyzed. A variety of column types and chromatographic modes were examined for developing each separation. For the ultra high performance supercritical fluid chromatography separations, analyses were performed using a series of Torus and Trefoil columns with either ammonium formate or ammonium hydroxide as additives, and methanol, ethanol or isopropanol organic solvents as modifiers. Ultra high performance liquid chromatographic separations were performed in both reversed phase and hydrophilic interaction chromatographic modes using SPP C18 and SPP HILIC columns. Gas chromatography separations were performed using an Elite‐5MS capillary column. The orthogonality of ultra high performance supercritical fluid chromatography, ultra high performance liquid chromatography, and gas chromatography was examined using principal component analysis. For the best overall separation of synthetic cathinones, the use of ultra high performance supercritical fluid chromatography in combination with gas chromatography is recommended.     

Industrial application of green chromatography--I. Separation and analysis of niacinamide in skincare creams using pure water as the mobile phase

In this work, chromatographic separation of niacin and niacinamide using pure water as the sole component in the mobile phase has been investigated. The separation and analysis of niacinamide have been optimized using three columns at different temperatures and various flow rates. Our results clearly demonstrate that separation and analysis of niacinamide from skincare products can be achieved using pure water as the eluent at 60 °C on a Waters XTerra MS C18 column, a Waters XBridge C18 column, or at 80 °C on a Hamilton PRP-1 column. The separation efficiency, quantification quality, and analysis time of this new method are at least comparable with those of the traditional HPLC methods. Compared with traditional HPLC, the major advantage of this newly developed green chromatography technique is the elimination of organic solvents required in the HPLC mobile phase. In addition, the pure water chromatography separations described in this work can be directly applied in industrial plant settings without further modification of the existing HPLC equipment.     

Reversed-phase liquid chromatographic separation and simultaneous profiling of steroidal glycoalkaloids and their aglycones

Improved and simplified reversed-phase liquid chromatographic conditions for the separation and simultaneous profiling of both steroidal glycoalkaloids and their aglycones, having solanidane- or spirosolane-type structures, are described. The most reproducible retention behavior for these ionizable compounds on C18 columns was achieved under isocratic and gradient elution conditions using acetonitrile in combination with triethylammonium phosphate buffer at pH 3.0, when basic functional groups of solutes and silanol groups on the silica are fully protonated minimizing ionic interactions. Gradient elution was the only feasible approach for the simultaneous separation of steroidal glycoalkaloids and their aglycones. A Zorbax SB C18 column, specially designed for low-pH separations, showed good performance in critical separations. The impurities of the commercial tomatine and tomatidine standards were studied and confirmed using mass spectrometric, liquid chromatographic and thin-layer chromatographic methods.     

Semi-preparative gas chromatographic separation of all-trans-perhydrotriphenylene enantiomers on a chiral cyclodextrin stationary phase

Enantiomers of all-trans-perhydrotriphenylene (PHTP) were separated by gas chromatography using heptakis(6-O-tert.-butyldimethylsilyl-2,3-di-O-methyl)-beta-cyclodextrin (TBDMS-beta-CD) as the chiral selector. Conditions for semi-preparative separations were established using a 2 m x 2 mm I.D. packed column and subsequently extended to a 1.8 m x 4 mm I.D. column which enabled separations on a mg scale. The column packing was TBDMS-beta-CD dissolved in SE-54 coated on Chromosorb P AW-DMCS 80-100 mesh. Optimization of the chromatographic conditions (oven temperature, carrier gas flow, and column load) with respect to better efficiency and peak retention resulted in a system capable of separating up to 10 mg of the racemate per day. Purities of separated enantiomers were determined by capillary gas chromatography. Yields and purities of the fractions obtained by single- and double-step separations are compared. Highly enriched enantiomers with purities of up to 99.6% (99.2% ee) were obtained by a single separation step.     

Comparison of log k′ — solvent composition relationships in thinlayer and column chromatography for systems of the type: Silanized silica — water + methanol

Relationships between log k' values of polynuclear hydrocarbons and composition of water/methanol mixtures were determined for HPTLC on RP-18 silica and for HPLC using RP-2 silica. In spite of differences in the adsorbents used, a good correlation between HPLC and TLC parameters was found. In the TLC experiments, a sandwich tank with a modified solvent distributor was used. It has been reported that thin-layer chromatography is a good technique for the preliminary optimization of column chromatographic separations [1–5]. So far, the comparison of TLC and HPLC has been mainly restricted to silica as the adsorbent. Since TLC plates precoated with silanized adsorbents recently became commercially available, it seemed interesting to compare the chromatographic parameters obtained for the “reversed phase” systems with the two techniques (see also ref. 6).     

Application of thin layer and high performance liquid chromatography to the separation and determination of cephalexin in cephradine,in bulk powder and in pharmaceuticals

Summary A thin-layer chromatographic procedure for the quantitative determination of cephalexin in cephradine formulations is described. The thin-layer chromatography is carried out on a silica gel layer and the quantitation is by UV scanning of the chromatogram. The procedure was transferred to high-performance liquid chromatography on a microparticulate silica gel column with a similar eluent system. The cephalexin content of a few commercial cephradine samples is determined by using these techniques. The results of these procedures are compared to those obtained with high-performance liquid chromatography on a C 18 reverse phase column.     

Chromatographic methods for the determination of pesticides in foods.

Chromatography is the most important technique available to the analyst dealing with the determination of pesticide residues in food, feed and environmental samples. Numerous methods for pesticide residues in foods have been developed in the past few years, and this paper reviews some of the most important procedures. A great variety of chromatographic methods, such as solid-phase extractions, column chromatographic clean-up methods, thin-layer, gas, high-performance liquid and supercritical fluid chromatography, and their coupling with sensitive and selective detection methods are surveyed.     

Ultrahigh pressure liquid chromatography using elevated temperature

Fast liquid chromatographic (LC) methods are important for a variety of applications. Reducing the particle diameter (d(p)) is the most effective way to achieve fast separations while preserving high efficiency. Since the pressure drop along a packed column is inversely proportional to the square of the particle size, when columns packed with small particles (<2 microm) are used, ultrahigh pressures (>689 bar) must be applied to overcome the resistance to mobile phase flow. Elevating the column temperature can significantly reduce the mobile phase viscosity, allowing operation at higher flow rate for the same pressure. It also leads to a decrease in retention factor. The advantage of using elevated temperatures in LC is the ability to significantly shorten separation time with minimal loss in column efficiency. Therefore, combining elevated temperature with ultrahigh pressure facilitates fast and efficient separations. In this study, C6-modified 1.0 microm nonporous silica particles were used to demonstrate fast separations using a temperature of 80 degrees C and a pressure of 2413 bar. Selected separations were completed in 30 s with efficiencies as high as 220,000 plates m(-1).     

Active flow management in preparative chromatographic separations: a preliminary investigation into enhanced separation using a curtain flow inlet fitting and segmented flow outlet fitting

Active flow management in the form of curtain flow sample introduction and segmented outlet flow control has been shown to enable sample to elute through a chromatography column under the principles of the "infinite diameter column". Such an elution process avoids the detrimental effects of the heterogeneity of particle-packed chromatographic columns by injecting the sample directly into the radial core region of the column, thus avoiding wall effects. The process described herein illustrates how the principles of the infinite diameter column can be applied using conventional injection devices suitable for long-term analysis that requires robust protocols. Using this approach, sensitivity in separation was 2.5 times greater than conventional chromatography, yielding a product at twice the concentration. Benefits of curtain flow injection are thus relevant to both preparative-scale and analytical-scale separations.     

Studies on azaspiracid biotoxins. I. Ultrafast high-resolution liquid chromatography/mass spectrometry separations using monolithic columns

In this study, the performance of monolithic columns was evaluated for ultrafast liquid chromatography/mass spectrometry (LC/MS) analyses and for high-resolution separations of several azaspiracid biotoxin analogs. Because of their high permeability, monolithic columns offer a number of advantages over conventional packed columns; viz., very low backpressures and relatively flat van Deemter curves at high flow rates. That is, very high flow rates can be used for ultrafast analyses or, by using longer than normal columns, high-resolution separations are possible. In a series of experiments, we varied the mobile phase flow rates between 1 and 8 mL/min, and studied their impact on chromatographic parameters such as retention time, resolution, number of plates and pressure. The chromatographic run times could be reduced to ca. 30 s without a significant change in the separation efficiency. A signal intensity comparison revealed interesting differences between atmospheric-pressure chemical ionization (APCI) and electrospray ionization (ESI) in their flow-rate dependency. An explanation with respect to the behavior as of a mass-flow or a concentration-dependent device is given in the paper. Additionally, the column length was varied between 10 and 70 cm. As a result, the number of theoretical plates increased substantially. In the example shown in the report, an increase from 13 000 plates for a 10-cm column to 80 000 for a 70-cm column is demonstrated. In addition, the potential of the monolithic columns for high-resolution LC/MS separations is shown for a complex biotoxin mixture, which was separated on a 40-cm-long column.     

Column properties and flow profiles of a flat, wide column for high-pressure liquid chromatography

The design and the construction of a pressurized, flat, wide column for high-performance liquid chromatography (HPLC) are described. This apparatus, which is derived from instruments that implement over-pressured thin layer chromatography, can carry out only uni-dimensional chromatographic separations. However, it is intended to be the first step in the development of more powerful instruments that will be able to carry out two-dimensional chromatographic separations, in which case, the first separation would be a space-based separation, LC(x), taking place along one side of the bed and the second separation would be a time-based separation, LC(t), as in classical HPLC but proceeding along the flat column, not along a tube. The apparatus described consists of a pressurization chamber made of a Plexiglas block and a column chamber made of stainless steel. These two chambers are separated by a thin Mylar membrane. The column chamber is a cavity which is filled with a thick layer (ca. 1mm) of the stationary phase. Suitable solvent inlet and outlet ports are located on two opposite sides of the sorbent layer. The design allows the preparation of a homogenous sorbent layer suitable to be used as a chromatographic column, the achievement of effective seals of the stationary phase layer against the chamber edges, and the homogenous flow of the mobile phase along the chamber. The entire width of the sorbent layer area can be used to develop separations or elute samples. The reproducible performance of the apparatus is demonstrated by the chromatographic separations of different dyes. This instrument is essentially designed for testing detector arrays to be used in a two-dimensional LC(x) x LC(t) instrument. The further development of two-dimension separation chromatographs based on the apparatus described is sketched.     

Methods to determine the kinetic performance limit of contemporary chromatographic techniques

By combining separation efficiency data as a function of flow rate with the column permeability, the kinetic plot method allows to determine the limits of separation power (time vs. efficiency) of different chromatographic techniques and methods. The technique can be applied for all different types of chromatography (liquid, gas, or supercritical fluid), for different types of column morphologies (packed beds, monoliths, open tubular, micromachined columns), for pressure and electro‐driven separations and in both isocratic and gradient elution mode. The present contribution gives an overview of the methods and calculations required to correctly determine these kinetic performance limits and their underlying limitations.     

Toxicological evaluation of harmful substances by in situ enzymatic and biological detection in high-performance thin-layer chromatography

The efficiency of a chromatographic analysis method is determined by the selectivity of the chromatographic separation and the specificity of the detection method. In the case of high-performance thin-layer chromatography (HPTLC) the separated components can be detected and quantified directly on the chromatogram by physical and chemical methods. By coupling high-performance thin-layer chromatography with biological or biochemical inhibition tests it was possible to detect toxicologically active substances in situ. A linear relationship was shown between the signal of the inhibition of cholinesterase and the concentration of the inhibitor using a constant enzyme concentration and a constant incubation time. The graph of the inhibition of the luminescence of Photobacterium vibrio fisheri in relation to the concentration of pentachlorophenol (range 20–80 ng) is nearly linear. Measurements were done by using a densitometer or a videodensitometric scanner.     

Comparison of reversed-phase and weak anion-exchange high-performance liquid chromatographic methods for peptide separations

Weak anion-exchange and reversed-phase high-performance liquid chromatographic methods for peptide separations were compared using a tryptic digest of "rat small myelin basic protein". In these experiments, a number of tryptic peptides that were not resolved on the reversed-phase column could be separated on the weak anion-exchange column, and in other instances, as might be expected, reversed-phase chromatography provided better resolution of certain peptides than did the weak anion-exchange method. The results obtained strongly suggest that the combined use of these two methods of separation, which utilize different selectivities, can provide an excellent improvement in resolving power for a number of peptide separations.     

Caffeine Determination in Human Saliva and Urine by TLC and Ultraviolet Absorption Densitometry

A quantitative method using thin-layer chromatography (TLC) plates with concentrating zone and ultraviolet absorption densitometry is described for caffeine (CAF) determination in human saliva and urine. The applicability of the CAF method was tested for saliva and urine from male individuals. The changes of salivary CAF, urinary CAF concentration and of urinary CAF excretion correspond with results of previous investigations using gas chromatography, high performance liquid chromatography, radioimmunoassay or enzyme immunoassay methods. In summary, the thin-layer chromatography/densitometry method here described is easy to perform, reproducible and accurate. Thus, it is suitable for routine analysis of CAF in human saliva or urine, being an effective alternative to other, more expensive and more time-consuming chromatographic or immunological methods.     

Glass capillary gas chromatography with electron-capture detection. Separation of prostaglandins

Glass capillary gas chromatography of the prostaglandins was performed on a system including an all-glass, solventless injector; thermostable methylphenyl-polysiloxane glass capillary columns; and a conventional electron-capture detector fitted with a make-up gas tee. The principal stable metabolites of prostaglandin endoperoxide were separated as perfluorinated derivatives in 35 min. Detection limits equal or exceed those obtained for packed column separations and electron capture detection. Prostaglandin endoperoxide metabolic profiles from mammalian cell cultures were obtained using this system. These profiling studies are not possible with other chromatographic methods because of inferior resolution and sensitivity.