可见光响应光催化剂Ag/AgCl@NH2-UiO-66的制备及其光催化性能

采用气相扩散-沉积-光还原法制备了可见光响应复合光催化剂Ag/AgCl@NH_2-UiO-66。通过X射线衍射(XRD)、电子扫描显微镜(SEM)、X射线能谱(EDS)、紫外可见漫反射光谱及X射线光电子能谱(XPS)等对催化剂的结构进行了表征。结果表明Ag/AgCl@NH_2-UiO-66具有优良的光催化活性,可见光条件下(λ≥420nm)对20mg·L~(-1)罗丹明的降解效率14min即可达到98%。     

W18O49/NH2-UiO-66复合催化剂的高效光催化CO2环加成

以2-氨基对苯二甲酸（H₂ATA）为配体,通过溶剂热法合成了Zr基MOF：NH₂-UiO-66,继而以氯化钨为前驱体,通过溶剂热法实现了富含氧空位的缺陷氧化钨（W₁₈O₄₉）在NH₂-UiO-66上的原位生长,构建了具有典型Ⅱ型异质结的复合光催化剂W₁₈O₄₉/NH₂-UiO-66。通过粉末X射线衍射、扫描电子显微镜、X射线光电子能谱和紫外可见漫反射光谱对催化剂的组成与结构进行了表征。在室温常压、模拟太阳光下,以氧化苯乙烯为模型底物,对所有样品的光催化活性进行了考察,W₁₈O₄₉/NH₂-UiO-66展现了最高的碳酸苯乙烯酯产率（58 mmol·g^-1·h^-1）。     

Z型Ag-Cu2O/BiVO4光催化剂的光催化还原CO2性能

利用简单的化学还原沉积法将 Cu₂O纳米球和 Ag纳米颗粒均匀包裹在十面体 BiVO₄表面,成功构建了一种具有高效电荷载流子分离/转移特性的Z型异质结光催化剂Ag-Cu₂O/BiVO₄。Ag-Cu₂O/BiVO₄在可见光下光催化CO₂还原为CO的产率可达5.37 μmol·g^-1·h^-1,分别是纯 BiVO₄和 Cu₂O的 35.80倍和 6.30倍。通过 X射线粉末衍射(XRD)、X射线光电子能谱(XPS)、扫描电子显微镜(SEM)、X射线能谱(EDS)、紫外可见漫反射光谱(UV-Vis DRS)、光致发光(PL)光谱、瞬态光电流响应(TPC)和电化学阻抗谱(EIS)对 Ag-Cu₂O/BiVO₄的晶体结构、形貌、组成、能带结构和吸光能力等进行了系统表征分析,并提出了其光催化体系还原CO₂的催化机理。     

溶剂热法制备Ag/TiO2纳米材料及其光催化性能

以乙醇为溶剂, 钛酸四丁酯为前驱体, 用溶剂热法制备了Ag表面修饰的负载型纳米二氧化钛光催化剂. 利用X射线衍射(XRD)、N₂吸附-脱附(BET)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)、紫外-可见(UV-Vis)光谱等技术对其进行了系统的表征, 以亚甲基蓝(MB)溶液的脱色降解为模型反应, 考察了不同Ag含量样品的光催化性能. 结果表明: 用溶剂热法制备的样品中TiO₂皆为锐钛矿相, 金属Ag颗粒沉积在TiO₂表面, 粒径为2 nm左右, 比表面积较溶胶凝胶法制备的样品大大增加, 最高可达151.44 m²·g^-1; UV-Vis光谱和光催化实验表明: Ag修饰使TiO₂对光的吸收能力大大增强, 吸收带边红移至可见光区, 亚甲基蓝在该复合材料上的光催化降解反应遵循一级反应动力学模型; 溶剂热法制备样品的光催化性能明显好于溶胶凝胶法制备的样品, 在紫外光和可见光下, Ag摩尔分数为5%的样品表现出最佳的光催化活性.     

溶剂热法制备Ag/TiO2纳米材料及其光催化性能

以乙醇为溶剂, 钛酸四丁酯为前驱体, 用溶剂热法制备了Ag表面修饰的负载型纳米二氧化钛光催化剂. 利用X射线衍射(XRD)、N₂吸附-脱附(BET)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)、紫外-可见(UV-Vis)光谱等技术对其进行了系统的表征, 以亚甲基蓝(MB)溶液的脱色降解为模型反应, 考察了不同Ag含量样品的光催化性能. 结果表明: 用溶剂热法制备的样品中TiO₂皆为锐钛矿相, 金属Ag颗粒沉积在TiO₂表面, 粒径为2 nm左右, 比表面积较溶胶凝胶法制备的样品大大增加, 最高可达151.44 m²·g^-1; UV-Vis光谱和光催化实验表明: Ag修饰使TiO₂对光的吸收能力大大增强, 吸收带边红移至可见光区, 亚甲基蓝在该复合材料上的光催化降解反应遵循一级反应动力学模型; 溶剂热法制备样品的光催化性能明显好于溶胶凝胶法制备的样品, 在紫外光和可见光下, Ag摩尔分数为5%的样品表现出最佳的光催化活性.     

溶剂热法制备Ag/TiO2纳米材料及其光催化性能

以乙醇为溶剂, 钛酸四丁酯为前驱体, 用溶剂热法制备了Ag表面修饰的负载型纳米二氧化钛光催化剂. 利用X射线衍射(XRD)、N₂吸附-脱附(BET)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)、紫外-可见(UV-Vis)光谱等技术对其进行了系统的表征, 以亚甲基蓝(MB)溶液的脱色降解为模型反应, 考察了不同Ag含量样品的光催化性能. 结果表明: 用溶剂热法制备的样品中TiO₂皆为锐钛矿相, 金属Ag颗粒沉积在TiO₂表面, 粒径为2 nm左右, 比表面积较溶胶凝胶法制备的样品大大增加, 最高可达151.44 m²·g^-1; UV-Vis光谱和光催化实验表明: Ag修饰使TiO₂对光的吸收能力大大增强, 吸收带边红移至可见光区, 亚甲基蓝在该复合材料上的光催化降解反应遵循一级反应动力学模型; 溶剂热法制备样品的光催化性能明显好于溶胶凝胶法制备的样品, 在紫外光和可见光下, Ag摩尔分数为5%的样品表现出最佳的光催化活性.     

溶剂热法制备Ag/TiO2纳米材料及其光催化性能

以乙醇为溶剂, 钛酸四丁酯为前驱体, 用溶剂热法制备了Ag表面修饰的负载型纳米二氧化钛光催化剂. 利用X射线衍射(XRD)、N₂吸附-脱附(BET)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)、紫外-可见(UV-Vis)光谱等技术对其进行了系统的表征, 以亚甲基蓝(MB)溶液的脱色降解为模型反应, 考察了不同Ag含量样品的光催化性能. 结果表明: 用溶剂热法制备的样品中TiO₂皆为锐钛矿相, 金属Ag颗粒沉积在TiO₂表面, 粒径为2 nm左右, 比表面积较溶胶凝胶法制备的样品大大增加, 最高可达151.44 m²·g^-1; UV-Vis光谱和光催化实验表明: Ag修饰使TiO₂对光的吸收能力大大增强, 吸收带边红移至可见光区, 亚甲基蓝在该复合材料上的光催化降解反应遵循一级反应动力学模型; 溶剂热法制备样品的光催化性能明显好于溶胶凝胶法制备的样品, 在紫外光和可见光下, Ag摩尔分数为5%的样品表现出最佳的光催化活性.     

溶剂热法制备Ag/TiO2纳米材料及其光催化性能

以乙醇为溶剂, 钛酸四丁酯为前驱体, 用溶剂热法制备了Ag表面修饰的负载型纳米二氧化钛光催化剂. 利用X射线衍射(XRD)、N₂吸附-脱附(BET)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)、紫外-可见(UV-Vis)光谱等技术对其进行了系统的表征, 以亚甲基蓝(MB)溶液的脱色降解为模型反应, 考察了不同Ag含量样品的光催化性能. 结果表明: 用溶剂热法制备的样品中TiO₂皆为锐钛矿相, 金属Ag颗粒沉积在TiO₂表面, 粒径为2 nm左右, 比表面积较溶胶凝胶法制备的样品大大增加, 最高可达151.44 m²·g^-1; UV-Vis光谱和光催化实验表明: Ag修饰使TiO₂对光的吸收能力大大增强, 吸收带边红移至可见光区, 亚甲基蓝在该复合材料上的光催化降解反应遵循一级反应动力学模型; 溶剂热法制备样品的光催化性能明显好于溶胶凝胶法制备的样品, 在紫外光和可见光下, Ag摩尔分数为5%的样品表现出最佳的光催化活性.     

溶剂热法制备Ag/TiO2纳米材料及其光催化性能

以乙醇为溶剂, 钛酸四丁酯为前驱体, 用溶剂热法制备了Ag表面修饰的负载型纳米二氧化钛光催化剂. 利用X射线衍射(XRD)、N₂吸附-脱附(BET)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)、紫外-可见(UV-Vis)光谱等技术对其进行了系统的表征, 以亚甲基蓝(MB)溶液的脱色降解为模型反应, 考察了不同Ag含量样品的光催化性能. 结果表明: 用溶剂热法制备的样品中TiO₂皆为锐钛矿相, 金属Ag颗粒沉积在TiO₂表面, 粒径为2 nm左右, 比表面积较溶胶凝胶法制备的样品大大增加, 最高可达151.44 m²·g^-1; UV-Vis光谱和光催化实验表明: Ag修饰使TiO₂对光的吸收能力大大增强, 吸收带边红移至可见光区, 亚甲基蓝在该复合材料上的光催化降解反应遵循一级反应动力学模型; 溶剂热法制备样品的光催化性能明显好于溶胶凝胶法制备的样品, 在紫外光和可见光下, Ag摩尔分数为5%的样品表现出最佳的光催化活性.     

溶剂热法制备Ag/TiO2纳米材料及其光催化性能

以乙醇为溶剂, 钛酸四丁酯为前驱体, 用溶剂热法制备了Ag表面修饰的负载型纳米二氧化钛光催化剂. 利用X射线衍射(XRD)、N₂吸附-脱附(BET)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)、紫外-可见(UV-Vis)光谱等技术对其进行了系统的表征, 以亚甲基蓝(MB)溶液的脱色降解为模型反应, 考察了不同Ag含量样品的光催化性能. 结果表明: 用溶剂热法制备的样品中TiO₂皆为锐钛矿相, 金属Ag颗粒沉积在TiO₂表面, 粒径为2 nm左右, 比表面积较溶胶凝胶法制备的样品大大增加, 最高可达151.44 m²·g^-1; UV-Vis光谱和光催化实验表明: Ag修饰使TiO₂对光的吸收能力大大增强, 吸收带边红移至可见光区, 亚甲基蓝在该复合材料上的光催化降解反应遵循一级反应动力学模型; 溶剂热法制备样品的光催化性能明显好于溶胶凝胶法制备的样品, 在紫外光和可见光下, Ag摩尔分数为5%的样品表现出最佳的光催化活性.     

Solvent extraction separation of In/III/-Tl/III/ and Hg/II/-Cd/II/-Co/II/ with sulphoxides

Solvent extraction studies have been made on some metals: In/III/-Tl/III/ and Hg/II/-Cd/II/-Co/II/, from ammonium thiocyanate solutions by dialkyl sulphoxides. Separation of these metals from one another can be achieved by suitable choice of the extracted conditions. The nature of the extractable metal species has been elucidated.     

Simultaneous propane dehydrogenation andco2hydrogenation overCrOx/SiO2catalyst

Summary Single reverse water-gas shift (RWGS) and dehydrogenation of propane with CO₂(DH-CO₂) reactions in the presence and absence of the CrO_x/SiO₂ catalyst have been studied between 673 and 873 K. It was found that the CrO_x/SiO₂ catalyst is active both in the dehydrogenation of propane and in the RWGS reactions. The obtained results suggest that the dehydrogenation of propane to propene in the presence of CO₂on CrO_x/SiO₂can be facilitated by the RWGS reaction.</o:p>     

Synthesis of chlorobis/β-diketonato/oxotechnetium/V/ and tris/β-diketonato/technetium/III/ complexes

Chlorobis/-diketonato/ oxotechnetium/V/ complexes [TcOCl/-dik/₂, -diketone=acetylacetone, benzoylacetone and dibenzoylmethane] were newly synthesized using macroamount of⁹⁹Tc. These complexes were further separated into geometrical isomers. Furthermore, an improvement of the yields for the syntheses of tris/-dike-tonato/technetium/III/ complexes [Tc/-dik/₃, -diketone=acetylacetone, benzoylacetone and 2-thenoyltrifluoroacetone] was examined using Tc/III/-thiourea complexes as a starting material.     

Direct synthesis of dimethyl carbonate ?from CH3OH AND CO2 by H3PW12O40/CexTi1-xO2 catalyst

Summary Ce_xTi_1-xO₂ and H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ catalysts were prepared using a sol-gel method, and applied to the direct synthesis of dimethyl carbonate from methanol and carbon dioxide. H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ showed a better catalytic performance than the corresponding Ce_xTi_1-xO₂, due to the bifunctional catalysis of Br?nsted acid sites (provided by H₃PW₁₂O₄₀) and base sites (provided by Ce_xTi_1-xO₂). H₃PW₁₂O₄₀/Ce_0.1Ti_0.9O₂ showed the highest catalytic performance among the H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ catalysts.     

An investigation of the promotional effect of propylene or propane traces on the activity of sulfatedPt/g-Al2O3andPt-Sn/g-Al2O3inCH4combustion

Summary A strong promoting effect of the presence of C₃H₈or C₃H₆was determined for the combustion of CH₄in excess oxygen, over pre-sulfated 1%Pt/g-Al₂O₃and pre-sulfated 1%Pt-2%Sn/g-Al₂O₃catalysts.</o:p>     

LixNi0.8-yCo0.2ZnyOp的合成及电化学性能研究

A series of single-phase Li_xNi_0.8-yCo_0.2Zn_yO_p(0.96 ≤x≤ 1.10， 0 ≤y≤ 0.05， 2 ≤p≤ 2(1+y) ) (different in the y values) were synthesized by a two-step solid state reaction method， in which LiOH·H₂O， Zn-doped spherical Ni(OH)₂ and Co₂O₃ were used as the precursors. The ICP-AES analyses proved that the Zn-doped compounds synthesized had the nonstoichiometric form. The results of the XRD， SEM identified that the uniform particles of the as-prepared materials having a good layered structure were fine， narrowly distributed and well crystallized. The electrochemical performance test was carried out and the results showed that the as-prepared Zn-doped materials had not only a high capacity， but also a better cycling stability characterization than the un-doped one. The Li_1.06Ni_0.75Co_0.22Zn_0.03O_2.03 material has an initial reversible capacity as high as 160.5mAh·g^-1; and a first discharge efficiency 89.2%， and exhibits satisfactory cyclic stability with 90% retainable capacity after 50 cycles.     

Crystal structure of Na3PO4 · 12H2O

The crystal structure of trisodium monophosphate hemihydrate was determined. The space group is $\text{C2}\text{c}$ and a unit cell contains eight formula units. The unit cell dimensions of $\text{Na}{}_3\text{PO}{}_4\text{·}\text{1}\text{2}\text{H}{}_2\text{O}$ are a = 9.631(3), b = 5.416(2), c = 16.938(8) Å, β = 102.60(5)°. The final R value is 0.027 for a set of 1430 independent reflections. This atomic arrangement is mainly a three-dimensional network of distorted NaO₆ octahedra. The hydrogen bonding scheme is given.     

Visible light-sensitive yellow TiO2−xNx and Fe-N co-doped Ti1−yFeyO2−xNx anatase photocatalysts

Nitrogen substituted yellow colored anatase TiO_2−xN_x and Fe-N co-doped Ti_1−yFe_yO_2−xN_x have been easily synthesized by novel hydrazine method. White anatase TiO_2−δ and N/Fe-N-doped samples are semiconducting and the presence of ESR signals at g ∼1.994-2.0025 supports the oxygen vacancy and g∼4.3 indicates Fe³⁺ in the lattice. TiO_2−xN_x has higher conductivity than TiO_2−x and Fe/Fe-N-doped anatase and the UV absorption edge of white TiO_2−x extends in the visible region in N, Fe and Fe-N co-doped TiO₂, which show, respectively, two band gaps at ∼3.25/2.63, ∼3.31/2.44 and 2.8/2.44 eV. An activation energy of ∼1.8 eV is observed in Arrhenius log resistivity vs. 1/T plots for all samples. All TiO₂ and Fe-doped TiO₂ show low 2-propanol photodegradation activity but have significant NO photodestruction capability, both in UV and visible regions, while standard Degussa P-25 is incapable in destroying NO in the visible region The mid-gap levels that these N and Fe-N-doped TiO₂ consist may cause this discrepancy in their photocatalytic activities.     

Carbon black and propylene oxidation over Ru/CoxMgyAl2Oz catalysts

The effects of Co_xMg_yAl₂O_z mixed oxides composition and ruthenium addition on the oxidation of propylene and carbon black (CB) were investigated. Different reactive cobalt and ruthenium oxide species were formed following calcination at 600 °C. The addition of ruthenium was beneficial for the CB oxidation under “loose contact” conditions and for propylene oxidation when the cobalt content was intermediate to low. The calculated activation energy for CB oxidation was decreased from 151 kJ mol⁻¹ for the uncatalyzed reaction to 111 kJ mol⁻¹ over the best catalyst.     

Structure refinement, dielectric, pyroelectric and Raman characterizations of Ba1−xLax(1−y)/2Euxy/2Nax/2TiO3 solid solution

The perovskite-type oxides Ba_1−xLa_x(1−y)/2Eu_xy/2Na_x/2TiO₃ (0?x?0.5 and xy=0.04) were synthesized and characterized by X-ray diffraction as well as dielectric measurements and Raman spectroscopy. The crystal structure of these ceramics has been determined by the Rietveld refinement powder X-ray diffraction data at room temperature. These compounds crystallize at room temperature in tetragonal space group P4mm for 0?x?0.1 and in the cubic group for 0.2?x?0.5. The phase transition temperature T_C (or T_m) decreases as x content increases. The degree of diffuseness of the phase transition is more pronounced for higher x content, implying the existence of a composition-induced diffuse phase transition of the ceramics with x?0.1. The evolution of the Raman spectra was studied as a function of various compositions at room temperature. The polarization state was checked by pyroelectric measurements.