Rapid analysis of aflatoxins B1, B2, and ochratoxin A in rice samples using dispersive liquid–liquid microextraction combined with HPLC

A novel, simple, and rapid method is presented for the analysis of aflatoxin B₁, aflatoxin B₂, and ochratoxin A in rice samples by dispersive liquid–liquid microextraction combined with LC and fluorescence detection. After extraction of the rice samples with a mixture of acetonitrile/water/acetic acid, mycotoxins were rapidly partitioned into a small volume of organic solvent (chloroform) by dispersive liquid–liquid microextraction. The three mycotoxins were simultaneously determined by LC with fluorescence detection after precolumn derivatization for aflatoxin B₁ and B₂. Parameters affecting both extraction and dispersive liquid–liquid microextraction procedures, including the extraction solvent, the type and volume of extractant, the volume of dispersive solvent, the addition of salt, the pH and the extraction time, were optimized. The optimized protocol provided an enrichment factor of approximately 1.25 and with detection of limits (0.06–0.5 μg/kg) below the maximum levels imposed by current regulations for aflatoxins and ochratoxin A. The mean recovery of three mycotoxins ranged from 82.9–112%, with a RSD less than 7.9% in all cases. The method was successfully applied to measure mycotoxins in commercial rice samples collected from local supermarkets in China.     

Simultaneous determination of four aflatoxins and ochratoxin A in ginger and related products by HPLC with fluorescence detection after immunoaffinity column clean‐up and postcolumn photochemical derivatization

Ginger, a widely used spice and traditional Chinese medicine, is prone to be contaminated by mycotoxins. A simple, sensitive, and reproducible method based on immunoaffinity column clean‐up coupled with HPLC and on‐line postcolumn photochemical derivatization with fluorescence detection was developed for the simultaneous determination of aflatoxins (AFs) B₁, B₂, G₁, G₂, and ochratoxin A (OTA) in 25 batches of gingers and related products marketed in China for the first time. The samples were first extracted by ultrasonication with methanol/water (80:20, v/v) and then cleaned up with immunoaffinity columns for analysis. Under the optimized conditions, the LODs and LOQs for the five mycotoxins were 0.03–0.3 and 0.1–0.9 μg/kg, respectively. The average recoveries ranged from 81.3–100.8% for AFs and from 88.6–99.5% for OTA at three spiking levels. Good linearity was observed for the analytes with correlation coefficients all >0.9995. All moldy gingers were contaminated with at least one kind of the five investigated mycotoxins, while none of them were found in normal gingers. Ginger powder samples were contaminated slightly with the contamination levels below the LOQs, while ginger tea bags were mainly contaminated by OTA at 1.05–1.19 μg/kg and ginger black tea bags were mainly contaminated by AFs at 3.37–5.76 μg/kg. All the contamination levels were below the legally allowable limits.     

Graphene‐coated magnetic‐sheet solid‐phase extraction followed by high‐performance liquid chromatography with fluorescence detection for the determination of aflatoxins B1, B2, G1, and G2 in soy‐based samples

A new method named graphene‐coated magnetic‐sheet solid‐phase extraction based on a magnetic three‐dimensional graphene sorbent was developed for the extraction of aflatoxins prior to high‐performance liquid chromatography with fluorescence detection. The use of a perforated magnetic‐sheet for fixing the magnetic nanoparticles is a new feature of the method. Hence, the adsorbent particles can be separated from sample solution without using an external magnetic field. This made the procedure very simple and easy to operate so that all steps of the extraction process (sample loading, washing, and desorption) were carried out continuously using two lab‐made syringe pumps. The factors affecting the performance of extraction procedure such as the extraction solvent, adsorbent dose, sample loading flow rate, ionic strength, pH, and desorption parameters were investigated and optimized. Under the optimal conditions, the obtained enrichment factors and limits of detection were in the range of 205–236 and 0.09–0.15 μg/kg, respectively. The relative standard deviations were <3.4 and 7.5% for the intraday (n = 6) and interday (n = 4) precisions, respectively. The developed method was successfully applied to determine aflatoxins B₁, B₂, G₁, and G₂ in different soy‐based food samples.     

Development of a multi‐mycotoxin liquid chromatography/tandem mass spectrometry method for sweet pepper analysis

A multi‐mycotoxin method was developed for the simultaneous determination of trichothecenes (nivalenol, deoxynivalenol, 3‐acetyldeoxynivalenol, 15‐acetyldeoxynivalenol, neosolaniol, fusarenon‐X, diacetoxyscirpenol, HT‐2 toxin, T‐2 toxin), aflatoxins (aflatoxin‐B₁, aflatoxin‐B₂, aflatoxin‐G₁ and aflatoxin‐G₂), Alternaria toxins (alternariol, alternariol methyl ether and altenuene), fumonisins (fumonisin‐B₁, fumonisin‐B₂ and fumonisin‐B₃), ochratoxin A, zearalenone, beauvericin and sterigmatocystin in sweet pepper. Sweet pepper was extracted with ethyl acetate/formic acid (99:1, v/v). After splitting up the extract, two‐thirds of the extract was cleaned up using an aminopropyl column followed by an octadecyl column. The remaining part was cleaned up using a strong anion‐exchange column. After recombination of both cleaned parts of the sample extract, the combined solvents were evaporated and the residue was dissolved in mobile phase; 20 µL was injected into the chromatographic system, so only one run was used to separate and detect the mycotoxins in positive electrospray ionization using selected reaction monitoring. The samples were analyzed with a Micromass Quattro Micro triple quadrupole mass spectrometer (Waters, Milford, MA, USA). The mobile phase consisted of variable mixtures of water and methanol, 1% acetic acid and 5 mM ammonium acetate. The limits of detection of the multi‐mycotoxin method varied from 0.32 µg.kg^?1 to 42.48 µg.kg^?1. The multi‐mycotoxin liquid chromatography/tandem mass spectrometry (LC/MS/MS) method fulfilled the method performance criteria required by the Commission Regulation (EC) No 401/2006. Sweet peppers inoculated by Fusarium species were analyzed using the developed method. Beauvericin (9–484 µg.kg^?1) and fumonisins (fumonisin‐B₁ up to 4330 µg.kg^?1, fumonisin‐B₂ up to 4900 µg.kg^?1, and fumonisin‐B₃ up to 299 µg.kg^?1) were detected. Copyright © 2008 John Wiley & Sons, Ltd.     

Ionic‐liquid‐based dispersive liquid–liquid microextraction combined with magnetic solid‐phase extraction for the determination of aflatoxins B1, B2, G1, and G2 in animal feeds by high‐performance liquid chromatography with fluorescence detection

A novel two‐step extraction technique combining ionic‐liquid‐based dispersive liquid–liquid microextraction with magnetic solid‐phase extraction was developed for the preconcentration and separation of aflatoxins in animal feedstuffs before high‐performance liquid chromatography coupled with fluorescence detection. In this work, ionic liquid 1‐octyl‐3‐methylimidazolium hexafluorophosphate was used as the extractant in dispersive liquid–liquid microextraction, and hydrophobic pelargonic acid modified Fe₃O₄ magnetic nanoparticles as an efficient adsorbent were applied to retrieve the aflatoxins‐containing ionic liquid. Notably, the target of magnetic nanoparticles was the ionic liquid rather than the aflatoxins. Because of the rapid mass transfer associated with the dispersive liquid–liquid microextraction and magnetic solid phase steps, fast extraction could be achieved. The main parameters affecting the extraction recoveries of aflatoxins were investigated and optimized. Under the optimum conditions, vortexing at 2500 rpm for 1 min in the dispersive liquid–liquid microextraction and magnetic solid‐phase extraction and then desorption by sonication for 2 min with acetonitrile as eluent. The recoveries were 90.3–103.7% with relative standard deviations of 3.2–6.4%. Good linearity was observed with correlation coefficients ranged from 0.9986 to 0.9995. The detection limits were 0.632, 0.087, 0.422 and 0.146 ng/mL for aflatoxins B₁, B2, G1, and G2, respectively. The results were also compared with the pretreatment method carried out by conventional immunoaffinity columns.     

Development of an economic ultrafast liquid chromatography with tandem mass spectrometry method for trace analysis of multiclass mycotoxins in Polygonum multiflorum

Rapid, economic, and highly effective determination of multiple mycotoxins in complex matrices has given huge challenges for the analytical method. In this study, an economic analytical strategy based on sensitive and rapid ultrafast liquid chromatography coupled to hybrid triple quadrupole/linear ion trap mass spectrometry technique was developed for the determination of seven mycotoxins of different chemical classes (aflatoxin B₁, B₂, G₁, and G₂, ochratoxin A, T‐2 toxin, and HT‐2 toxin) in Polygonum multiflorum. Target mycotoxins were completely extracted using a modified quick, easy, cheap effective, rugged, and safe method without additional clean‐up steps. The types of extraction solvents and adsorbents for the extraction procedure were optimized to achieve high recoveries and reduce coextractives in the final extracts. Due to significant matrix effects for all analytes (≤68.9% and ≥110.0%), matrix‐matched calibration curves were introduced for reliable quantification, exploring excellent linearity for the seven mycotoxins with coefficients of determination >0.9992. The method allowed high sensitivity with limit of detection in the range of 0.031–2.5 μg/kg and limit of quantitation in the range of 0.078–6.25 μg/kg, as well as satisfactory precision with relative standard deviations lower than 8%. Recovery rates were between 74.3 and 119.8% with relative standard deviations below 7.43%. The proposed method was successfully applied for 24 batches of P. multiflorum samples, and six samples were found to be positive with aflatoxin B₁, B₂, G₁, or ochratoxin A. The method with significant advantages, including minimum analytical time, low time and solvent consumption, and high sensitivity, would be a preferred candidate for economic analysis of multiclass mycotoxins in complex matrices.     

Simultaneous determination of major type‐B trichothecenes and the de‐epoxy metabolite of deoxynivalenol in chicken tissues by HPLC–MS/MS

In this study, a specific and sensitive LC–MS/MS method for the simultaneous analysis of type‐B trichothecenes (deoxynivalenol, 3‐acetyldeoxynivalenol, and 15‐acetyldeoxynivalenol) and the de‐epoxy metabolite of deoxynivalenol (de‐epoxy‐deoxynivalenol) in chicken muscle, liver, kidney, and fat tissues was developed and validated. The method involved an extraction step using ethyl acetate, followed by the evaporation of the supernatant, which was further purified by an Oasis HLB SPE cartridge (Waters, Milford, MA, USA). Chromatographic separation was performed on a C₁₈ column by detection with MS in multiple‐reaction monitoring mode and using a gradient elution program with 0.1% formic acid in water and methanol. The correlation coefficients (r) for each calibration curve were >0.99 within the experimental concentration range. The extraction recoveries ranged from 73.7 to 106.4%, with intraday and interday RSD < 11.6% at three levels of concentrations of 2, 10, and 100 μg/kg. The decision limits and the detection capabilities of the analytes in the chicken tissues ranged from 0.16 to 0.92 and 0.68 to 2.07 μg/kg, respectively. The results demonstrated the applicability of this sensitive procedure to the determination of trichothecenes in chicken tissue samples.     

Development of a sensitive and reliable high performance liquid chromatography method with fluorescence detection for high-throughput analysis of multi-class mycotoxins in Coix seed

As an edible and medicinal plant, Coix seed is readily contaminated by more than one group of mycotoxins resulting in potential risk to human health. A reliable and sensitive method has been developed to determine seven mycotoxins (aflatoxins B₁, B₂, G₁, G₂, zearalenone, α-zearalenol, and β-zearalenol) simultaneously in 10 batches of Coix seed marketed in China. The method is based on a rapid ultrasound-assisted solid–liquid extraction (USLE) using methanol/water (80/20) followed by immunoaffinity column (IAC) clean-up, on-line photochemical derivatization (PCD), and high performance liquid chromatography coupled with fluorescence detection (HPLC-FLD). Careful optimization of extraction, clean-up, separation and detection conditions was accomplished to increase sample throughput and to attain rapid separation and sensitive detection. Method validation was performed by analyzing samples spiked at three different concentrations for the seven mycotoxins. Recoveries were from 73.5% to 107.3%, with relative standard deviations (RSDs) lower than 7.7%. The intra- and inter-day precisions, expressed as RSDs, were lower than 4% for all studied analytes. Limits of detection and quantification ranged from 0.01 to 50.2 μg kg⁻¹, and from 0.04 to 125.5 μg kg⁻¹, respectively, which were below the tolerance levels for mycotoxins set by the European Union. Samples that tested positive were further analyzed by HPLC tandem electrospray ionization mass spectrometry for confirmatory purposes. This is the first application of USLE-IAC-HPLC-PCD-FLD for detecting the occurrence of multi-class mycotoxins in Coix seed.     

Simultaneous determination of aflatoxin B1, B2, G1, and G2 in corn powder,edible oil,peanut butter,and soy sauce by liquid chromatography with tandem mass spectrometry utilizing turbulent flow chromatography

A novel fully automated method based on dual column switching using turbulent flow chromatography followed by liquid chromatography with tandem mass spectrometry was developed for the determination of aflatoxin B₁, B₂, G₁, and G₂ in corn powder, edible oil, peanut butter, and soy sauce samples. After ultrasound‐assisted extraction, samples were directly injected to the chromatographic system and the analytes were concentrated into the clean‐up loading column. Through purge switching, the analytes were transferred to the analytical column for subsequent detection by mass spectrometry. Different types of TurboFlow^TM columns, transfer flow rate, transfer time were optimized. The limits of detection and quantification of this method ranged between 0.2–2.0 and 0.5–4.0 μg/kg for aflatoxins in different matrixes, respectively. Recoveries of aflatoxins were in range of 83–108.1% for all samples, matrix effects were in range of 34.1–104.7%. The developed method has been successfully applied in the analysis of aflatoxin B₁, B₂, G₁, and G₂ in real samples.     

Monodisperse silica nanoparticles coated with gold nanoparticles as a sorbent for the extraction of phenol and dihydroxybenzenes from water samples based on dispersive micro‐solid‐phase extraction: Response surface methodology

A selective and sensitive method was developed based on dispersive micro‐solid‐phase extraction for the extraction of hydroquinone, resorcinol, pyrocatechol and phenol from water samples prior to high‐performance liquid chromatography with UV detection. SiO₂, SiO₂@MPTES, and SiO₂@MPTES@Au nanoparticles (MPTES = 3‐mercaptopropyltriethoxysilane) were synthesized and characterized by scanning electronic microscopy, thermogravimetric analysis, differential thermogravimetric analysis, and infrared spectroscopy. Variables such as the amount of sorbent (mg), pH and ionic strength of sample the solution, the volume of eluent solvent (μL), vortex and ultrasonic times (min) were investigated by Plackett–Burman design. The significant variables optimized by a Box–Behnken design were combined by a desirability function. Under optimized conditions, the calibration graphs of phenol and dihydroxybenzenes were linear in a concentration range of 1–500 μg/L, and with correlation coefficients more than 0.995. The limits of detection for hydroquinone, resorcinol, pyrocatechol, and phenol were 0.54, 0.58, 0.46, and 1.24 μg/L, and the limits of quantification were 1.81, 1.93, 1.54, and 4.23 μg/L, respectively. This procedure was successfully employed to determine target analytes in spiked water samples; the relative mean recoveries ranged from 93.5 to 98.9%.     

Extraction of aflatoxins from food samples using graphene‐based magnetic nanosorbents followed by high‐performance liquid chromatography: A simple solution to overcome the problems of immunoaffinity columns

In this research, magnetic graphene nanoparticles were prepared and used as adsorbents for preconcentrating the aflatoxins in rice, wheat, and sesame samples. For this purpose, graphene was synthesized by Hummer's method. Magnetically modified graphene formed by the deposition of magnetite (Fe₃O₄) on graphene was used for the separation of aflatoxins B₁, B₂, G₁, and G₂ from the samples. The extractants were subsequently analyzed with high‐performance liquid chromatography and fluorescence detection. Parameters affecting the efficiency of the method were thoroughly investigated. The measurements were done under the optimized conditions. For aflatoxins B₁, B₂, G₁, and G₂, limits of detection were 0.025, 0.05, 0.05, and 0.075 ng/g and limits of quantification were 0.083, 0.16, 0.16, and 0.23 ng/g, respectively. Accuracy was examined by the determination of the relative recovery of the aflatoxins. The relative recovery of aflatoxins B₁, B₂, G₁, and G₂ were quite satisfactory (between 64.38 and 122.21% for food samples). Relative standard deviations for within laboratory repeatability (n = 6) were in the range from 1.3 to 3.2. The application of this sorbent for the separation and concentration of the mentioned aflatoxins from food samples was examined.     

Detection of 13 mycotoxins in feed using modified QuEChERS with dispersive magnetic materials and UHPLC–MS/MS

An analytical method for the simultaneous determination of 13 mycotoxins in feed by magnetic dispersive solid‐phase extraction combined with ultra‐high performance liquid chromatography and tandem mass spectrometry was developed. The samples were extracted with acetonitrile/water (80:20, v/v, containing 3% acetic acid), and separated by centrifugation after salting‐out, and then treated with magnetic adsorbents to remove interferences. The separation of target mycotoxins was performed on an ACQUITY UPLC HSS T3 column using a mobile phase consisting of 1 mmol/L ammonium acetate with 0.1% formic acid and methanol by gradient elution. Good linearities for the 13 mycotoxins were achieved with correlation coefficients over 0.99, and the recoveries of mycotoxins were in the range of 89.3–112.6% at spiking at levels of 5, 20, and 100 μg/kg, with relative standard deviations of 0.9–10.4%. Based on the functional magnetic materials (MDN@Fe₃O₄, PSA@Fe₃O₄, ZrO_2@Fe₃O₄) applied in dispersive solid‐phase extraction, the pretreatment process is more convenient and it is beneficial to reduce the experimental cost by reusing the recycled magnetic materials. It is a simple, rapid, and environmentally friendly analytical method for the determination of mycotoxins in feed.     

High‐throughput multipesticides residue analysis in earthworms by the improvement of purification method: Development and application of magnetic Fe3O4‐SiO2 nanoparticles based dispersive solid‐phase extraction

As a key representative organism, earthworms can directly illustrate the influence of pesticides on environmental organisms in soil ecosystems. The present work aimed to develop a high‐throughput multipesticides residue analytical method for earthworms using solid–liquid extraction with acetonitrile as the solvent and magnetic material‐based dispersive solid‐phase extraction for purification. Magnetic Fe₃O₄ nanoparticles were modified with a thin silica layer to form Fe₃O₄‐SiO₂ nanoparticles, which were fully characterized by field‐emission scanning electron microscopy, transmission electron microscopy, Fourier‐transform infrared spectroscopy, X‐ray diffractometry, and vibrating sample magnetometry. The Fe₃O₄‐SiO₂ nanoparticles were used as the separation media in dispersive solid‐phase extraction with primary secondary amine and ZrO₂ as the cleanup adsorbents to eliminate matrix interferences. The amounts of nanoparticles and adsorbents were optimized for the simultaneous determination of 44 pesticides and six metabolites in earthworms by liquid chromatography with tandem mass spectrometry. The method performance was systematically validated with satisfactory results. The limits of quantification were 20 μg/kg for all analytes studied, while the recoveries of the target analytes ranged from 65.1 to 127% with relative standard deviation values lower than 15.0%. The developed method was subsequently utilized to explore the bioaccumulation of bitertanol in earthworms exposed to contaminated soil, verifying its feasibility for real sample analysis.     

Dispersive solid‐phase extraction followed by vortex‐assisted dispersive liquid–liquid microextraction based on the solidification of a floating organic droplet for the determination of benzoylurea insecticides in soil and sewage sludge

A novel dispersive solid‐phase extraction combined with vortex‐assisted dispersive liquid–liquid microextraction based on solidification of floating organic droplet was developed for the determination of eight benzoylurea insecticides in soil and sewage sludge samples before high‐performance liquid chromatography with ultraviolet detection. The analytes were first extracted from the soil and sludge samples into acetone under optimized pretreatment conditions. Clean‐up of the extract was conducted by dispersive solid‐phase extraction using activated carbon as the sorbent. The vortex‐assisted dispersive liquid–liquid microextraction based on solidification of floating organic droplet procedure was performed by using 1‐undecanol with lower density than water as the extraction solvent, and the acetone contained in the solution also acted as dispersive solvent. Under the optimum conditions, the linearity of the method was in the range 2–500 ng/g with correlation coefficients (r) of 0.9993–0.9999. The limits of detection were in the range of 0.08–0.56 ng/g. The relative standard deviations varied from 2.16 to 6.26% (n = 5). The enrichment factors ranged from 104 to 118. The extraction recoveries ranged from 81.05 to 97.82% for all of the analytes. The good performance has demonstrated that the proposed methodology has a strong potential for application in the multiresidue analysis of complex matrices.     

Simple magnetization of Fe3O4/MIL‐53(Al)‐NH2 for a rapid vortex‐assisted dispersive magnetic solid‐phase extraction of phenol residues in water samples

The present work describes a simple route to magnetize MIL‐53(Al)‐NH₂ sorbent for rapid extraction of phenol residues from environmental samples. To extend the applications and performances of the metal‐organic frameworks in the field of adsorption materials, we combined the properties of metal‐organic frameworks and magnetite to decrease the extraction time and simplify the extraction process as well. In this study, a simple and quick vortex‐assisted dispersive magnetic solid phase extraction method for the extraction of ten United States Environmental Protection Agency's priority phenols from water samples prior to analysis by high‐performance liquid chromatography with photodiode array detection was proposed. The developed method exhibits a rapid enrichment of the target analytes within 10 s for extraction and 10 s for desorption. Low detection limits of 1.8‐41.7 µg/L and quantitation limits of 6.0‐139.0 µg/L with the relative standard deviations for intra‐ and interday analyses less than 12% were achieved. Satisfactory recoveries in the range of 80‐111% with the relative standard deviations less than 11% demonstrated that Fe₃O₄/MIL‐53(Al)‐NH₂ is promising sorbent in the field of magnetic solid‐phase extraction for environmental samples.     

New application of chitosan‐grafted polyaniline in dispersive solid‐phase extraction for the separation and determination of phthalate esters in milk using high‐performance liquid chromatography

Chitosan‐grafted polyaniline was synthesized and applied as a sorbent for the preconcentration of phthalate esters in dispersive solid‐phase extraction. By coupling dispersive solid‐phase extraction with high‐performance liquid chromatography and response surface methodology (central composite design), a reliable, sensitive, and cost‐effective method for simultaneous determination of phthalate esters including dimethyl phthalate, di‐n‐butyl phthalate, and di(2‐ethylhexyl)phthalate was developed. The morphology of sorbent had been studied by scanning electron microscopy and its chemical structure confirmed by Fourier transform infrared spectroscopy. Under optimum condition, good linearity was observed in the range of 5.0–5000.0 ng/mL. The limits of detection (S/N = 3) and limits of quantification (S/N = 10) were 0.1–0.3 and 0.3–1 ng/mL, respectively. The relative standard deviations were less than 8.8%. Finally, this procedure was employed for extraction of trace amounts of phthalic acid esters in milk samples, the relative recoveries ranged from 82 to 103%.     

Determination of Aflatoxins in Rice and Maize by Ultra-High Performance Liquid Chromatography–Tandem Mass Spectrometry with Accelerated Solvent Extraction and Solid-Phase Extraction

A fast and reliable ultra-high performance liquid chromatography–tandem mass spectrometry method was developed for the determination of aflatoxins B₁, B₂, G₁, and G₂ in cereal. The analytes were extracted by accelerated solvent extraction with methanol/water (80:20). A polymeric solid-phase extraction column was used for sample preparation. Under optimum conditions, the analyte recoveries for samples spiked at different concentration levels in rice and maize ranged from 71.2 to 94.0%, with relative standard deviations less than 16.4%. Limits of detection (signal-to-noise ratio, 3:1) for the aflatoxins ranged from 0.25 to 0.93 ng/g. The developed method was applied to the determination of aflatoxins in ten rice and maize samples. One maize sample tested positive with an aflatoxin B₁ concentration of 2.7 ng/g.     

Application of ionic‐liquid‐supported magnetic dispersive solid‐phase microextraction for the determination of acaricides in fruit juice samples

In this study, ionic liquid (IL) supported magnetic dispersive solid‐phase microextraction was developed and a systematic investigation was conducted on imidazolium ILs for their extraction performance. This nano‐based pretreatment procedure was then applied for the determination of acaricides in fruit juice samples for the first time. A feature of this technique is that the commonly laborious chemical modification of magnetic nanoparticles (MNPs) was skillfully circumvented. Because of the combination of ILs, dispersive liquid–liquid microextraction, and dispersive MNP solid‐phase microextraction, the extraction efficiency can be significantly improved using commercial MNPs. Parameters of the extraction method were investigated by one‐factor‐at‐a‐time approach. The optimal experimental conditions were as follows: emulsification for 2 min by sonication with the addition of 50 μL [C₆MIM][NTf₂] in the dispersive liquid–liquid microextraction step and vortexing for 90 s after adding 40 mg spherical barium ferrite nanoparticles (20 nm). The desorption time was 2 min. Good linearity (0.5–500 ng/mL) and detection limits within the range of 0.05–0.53 ng/mL were achieved. The application of the proposed method was demonstrated by the analysis of real fruit juice samples, in which recoveries between 85.1 and 99.6% were obtained.     

Development of air‐assisted dispersive micro‐solid‐phase extraction‐based supramolecular solvent‐mediated Fe3O4@Cu–Fe–LDH for the determination of tramadol in biological samples

A simple method, air‐assisted dispersive micro‐solid‐phase extraction‐based supramolecular solvent was developed for the preconcentration of tramadol in biological samples prior to gas chromatography–flame ionization detection. A new type of carrier liquid, supramolecular solvent based on a mixture of 1‐dodecanol and tetrahydrofuran was combined with layered double hydroxide coated on a magnetic nanoparticle (Fe₃O₄@SiO₂@Cu–Fe–LDH). The supramolecular solvent was injected into the solution containing Fe₃O₄@SiO₂@Cu–Fe–LDH in order to provide high stability and dispersion of the sorbent without any stabilizer agent. Air assisted was applied to enhance the dispersion of the sorbent and solvent. A number of analytical techniques such as Fourier transform‐infrared spectrometry, field emission scanning electron microscope, energy‐dispersive X‐ray spectroscopy and X‐ray diffraction measurements were applied to assess the surface chemical characteristics of Fe₃O₄@SiO₂@Cu–Fe–LDH nanoparticles. The effects of important parameters on the extraction recovery were also investigated. Under optimized conditions, the limits of detection and quantification were obtained in the range of 0.9–2.4 and 2.7–7.5 μg L^?1 with preconcentration factors in the range of 450–472 in biological samples. This method was used for the determination of tramadol in biological samples (plasma, urine and saliva samples) with good recoveries.     

Determination of abamectin in citrus fruits using SPE combined with dispersive liquid–liquid microextraction and HPLC–UV detection

A new pretreatment method, SPE combined with dispersive liquid–liquid microextraction, was proposed for the determination of abamectin in citrus fruit samples for the first time. In this method, fruit samples were extracted by ultrasound‐assisted extraction followed by SPE. Then, the SPE was used as a disperser solvent in the next dispersive liquid–liquid microextraction step for further purification and enrichment of abamectin. The effects of various parameters on the extraction efficiency of the proposed method were investigated and optimized. Good linearity of abamectin was obtained from 0.005 to 10.0 mg/kg for B_1a and from 0.05 to 10.0 mg/kg for B_1b with correlation coefficient (r²) of 0.998 for B_1a and 0.991 for B_1b, respectively. The LODs were 0.001 and 0.008 mg/kg (S/N = 3) for B_1a and B_1b, respectively. The relative recoveries at three spiked levels were ranged from 87 to 96% with the RSD less than 11% (n = 3). The method has been successfully applied to the determination of abamectin in citrus fruit samples.