酸处理对CuY催化剂孔结构及氧化羰基化性能的影响

对NaY分子筛(n_Si/n_Al=2.65)进行了草酸脱铝处理并作为载体采用液相离子交换法制备CuY催化剂, 应用于常压甲醇氧化羰基化合成碳酸二甲酯(DMC)反应。NaY分子筛及其CuY催化剂通过N₂低温吸附-脱附、透射电子显微镜、X射线衍射、²⁹Si固体核磁共振、NH₃吸附程序升温脱附、吡啶吸附红外光谱、H₂程序升温还原、原子吸收等方法进行表征。研究结果表明, 酸处理NaY分子筛后, 骨架铝被脱除, 导致骨架n_Si/n_Al比增加、相对结晶度降低并产生介孔, 有利于产物分子的扩散, 从而影响催化活性。采用4 h、2 mol·L^-1草酸处理NaY分子筛作为载体制备的CuY催化剂显示出较高的催化性能, DMC时空收率和甲醇转化率分别从103.6 mg·g^-1·h^-1和6.3%增加到184.9 mg·g^-1·h^-1和10.2%。产生的介孔能够促进催化剂中铜活性位的可接近性及反应物分子和产物分子的扩散。     

酸处理对CuY催化剂孔结构及氧化羰基化性能的影响

对NaY分子筛(n_Si/n_Al=2.65)进行了草酸脱铝处理并作为载体采用液相离子交换法制备CuY催化剂,应用于常压甲醇氧化羰基化合成碳酸二甲酯(DMC)反应。NaY分子筛及其CuY催化剂通过N₂低温吸附-脱附、透射电子显微镜、X射线衍射、²⁹Si固体核磁共振、NH₃吸附程序升温脱附、吡啶吸附红外光谱、H₂程序升温还原、原子吸收等方法进行表征。研究结果表明,酸处理NaY分子筛后,骨架铝被脱除,导致骨架n_Si/n_Al比增加、相对结晶度降低并产生介孔,有利于产物分子的扩散,从而影响催化活性。采用4 h、2 mol·L^-1草酸处理NaY分子筛作为载体制备的CuY催化剂显示出较高的催化性能,DMC时空收率和甲醇转化率分别从103.6 mg·g^-1·h^-1和6.3%增加到184.9 mg·g^-1·h^-1和10.2%。产生的介孔能够促进催化剂中铜活性位的可接近性及反应物分子和产物分子的扩散。     

介孔调变对CuY催化剂甲醇氧化羰基化反应活性的影响

碱溶液处理NaY分子筛形成的介孔有利于反应物及产物分子的扩散,调节碱溶液浓度可控制Y分子筛中的介孔结构,通过溶液离子交换法制备CuY催化剂,研究了NaY分子筛介孔结构调变对CuY催化剂催化甲醇氧化羰基化反应活性的影响。通过BET、~(29)Si-NMR、XRD、NH_3/CO-TPD、H_2-TPR和TEM等表征及催化活性分析表明,在碱溶液处理过程中,NaY分子筛骨架中的Si(0Al)和Si(1Al)原子被优先脱除,且笼结构坍塌使得临近超笼连接,逐步形成直径为3.47~3.66 nm,孔容介于0.142~0.226cm~3·g~(-1)的介孔,在提高反应物分子和产物分子扩散性能的同时,提高了活性物种的可接近性。随着碱液浓度的增加,CuY催化剂的催化活性先升高后降低。当碱液浓度为0.2 mol·L~(-1)时,NaY分子筛介孔直径为3.47 nm,孔容达到最大(0.226 cm~3·g~(-1)),相应CuY催化剂DMC的时空收率、选择性和甲醇转化率分别达到204.0 mg·g~(-1)·h~(-1)、67.8%和14.0%,活性最佳。     

壳聚糖基多孔碳材料的制备及其超级电容性能

以胶态SiO₂纳米粒子为模板,壳聚糖为碳源,ZnCl2为活化剂,制备了具有不同比表面积和孔体积的氮掺杂介孔碳。采用多种表征手段对碳材料的微观形貌、比表面积和孔道结构进行了表征,探究了壳聚糖与SiO₂纳米粒子的比例以及ZnCl2活化剂对碳材料孔体积和比表面积的影响。结果表明,在未使用活化剂时碳材料(CSi-1.75)的孔体积高达4.53 cm³·g^-1,但其比表面积最小(729 m²·g^-1);使用ZnCl₂作为活化剂制备的碳材料(CSi-1.75-Zn)比表面积为1032 m²·g^-1,但其孔体积下降到1.99 cm³·g^-1,且具有最多的吡啶氮和吡咯氮。在以6.0 mol·L^-1 KOH为电解液的三电极体系中,当电流密度为0.5 A·g^-1时,CSi-1.75-Zn的比电容为344 F·g^-1,而CSi-1.75的比电容仅为255 F·g^-1。这表明碳材料的比表面积对超级电容性能影响最大,而孔体积影响较小。电容贡献分析结果表明,相对于CSi-1.75,CSi-1.75-Zn的双电层电容和赝电容都得到了提高,这表明更大的比表面积和更多的吡啶氮和吡咯氮有利于提高碳材料的超级电容性能。     

以催化裂化废催化剂为原料合成NaY分子筛的研究

针对催化裂化(FCC)废催化剂的回收利用问题,提出了一种废催化剂再利用的方法,即以FCC废催化剂为铝源,合成时只补充部分硅源,采用自制的高效NaY沸石导向剂,水热合成NaY分子筛。同时,以普通的化工原料合成了对比试样Y型分子筛。讨论了不同的FCC废催化剂预处理方式对合成产物性能的影响,发现以经过碱熔活化处理的废催化剂为原料合成的Y分子筛拥有更高的结晶度和纯度。采用X射线衍射、热分析、程序升温脱附法(NH3-TPD)和N₂静态容量吸附法对结晶产物和对比样品的晶体结构,热稳定性、酸性质、比表面积以及孔分布进行了表征。结果显示,以FCC废催化剂为原料完全可以合成出与普通原料性能接近的NaY分子筛。其BET比表面积可以达到615 m²·g^-1,孔体积可达0.38 cm³·g^-1,孔径集中在0.51 nm左右。     

大孔Mo-Ni/Al2O3催化剂的催化裂化柴油加氢性能研究

采用三次纳米自组装合成法,制备了一种以二次纳米自组装Al₂O₃为主体的大孔主客体催化剂FA-40,具有0.78cm³·g^-1的孔容、114m₂·g^-1的比表面积、27nm的平均孔径、6.0nm和40nm的双峰孔结构、孔分布在10~100nm高度集中、低堆积密度为0.56g·cm^-3、活性金属含量高达35.70%。XRD和TEM分析结果显示,活性金属以直径小于2nm的微晶态纳米粒子形式均匀分散于主体表面。采用劣质催化裂化柴油进行20h加氢实验评价,反应趋于稳定时,FA-40的脱硫、脱氮及芳烃饱和率分别达到94.4%、95.5%和67.9%,与F-5相比分别提高了20%、80%和140%。300h的长周期加氢实验表明,FA-40具有良好的加氢性能。     

Zn掺杂Co9S8纳米材料的制备及其在超级电容器和电催化析氢中的应用

采用原位溶剂热生长法设计合成了锌掺杂Co₉S₈纳米颗粒。各种表征技术和性能测试结果表明：锌掺杂Co₉S₈纳米颗粒的孔尺寸为18 nm,比表面积为23 m²·g^-1;同时微量的锌掺杂显著增强了Co₉S₈的电催化析氢（HER）活性及电容器性能。在HER性能测试中,当电流密度为10 mA·cm^-2时电位为-361 mV,电流密度最高可达38.26 mA·cm^-2,且具有优异的循环稳定性。同时在电容器性能测试中具有较高的比电容,当电流密度为1 A·g^-1时,质量比电容和面积比电容分别为235.48 F·g^-1和812.4 mF·cm^-2。     

CoAl2O4/蜂窝陶瓷催化剂的制备及其催化臭氧化性能

采用涂覆法制备了CoAl₂O₄/蜂窝陶瓷催化剂。利用X射线衍射、N₂吸附-脱附和透射电镜等方法对所制备的催化剂进行了表征,并分析了其催化臭氧化降解对苯二酚的效能。结果表明,CoAl₂O₄/蜂窝陶瓷的晶相属于典型的尖晶石结构,具有较大的比表面积、孔容和孔径,分别达到77 m²·g^-1、0.001 7 cm³·g^-1和3.9 nm。CoAl₂O₄/蜂窝陶瓷催化臭氧化对苯二酚的去除率高达81.2%,COD去除率可达47.7%。在叔丁醇存在的条件下,对苯二酚的去除率显著下降,说明CoAl₂O₄/蜂窝陶瓷催化臭氧化遵循羟基自由基机理。     

氮掺杂有序介孔碳-Ni纳米复合材料的制备及电化学性能

以F₁₂₇为模板剂,NiCl₂为镍源,尿素为氮源,间苯二酚甲醛原位聚合树脂为碳源,分别采用均相法和两相法制备Ni-N-OMC-1,Ni-N-OMC-2纳米复合材料.X射线衍射(XRD)、激光拉曼以及透射电子显微镜(TEM)等测试结果表明,复合材料具有有序介孔结构,Ni以金属微粒形式嵌于碳骨架中,提高了有序介孔碳的石墨化程度.X射线光电子能谱测试(XPS)表明尿素热解后以4种形式存在:sp³杂化与C结合的N原子,吡啶N原子,sp²杂化与C结合的N原子以及quaternary-N原子.Ni-N的共改性改变了碳载体的理化性质,有利于Pt纳米粒子的负载与分散.均相法制备的Ni-N-OMC-1复合材料微波负载Pt后,氧还原极限电流密度为5.32mA·cm^-2,氢氧化电化学活性面积高达138.53m²·g^-1,电化学催化活性优于商业20%Pt/C材料(4.49mA·cm^-2,96.98m²·g^-1).     

柠檬酸溶液中NaY分子筛的脱铝行为

硅铝分子筛有机酸配合脱铝是提高其稳定性、引入介孔的一种重要方法.采用X射线衍射、N₂物理吸附、高分辨透射电镜、傅里叶变换红外光谱、²⁷Al和²⁹Si固体魔角自旋核磁共振光谱等方法研究了NaY分子筛柠檬酸脱铝行为.结果表明,柠檬酸浓度对NaY分子筛骨架Al原子的脱出影响尤为显著.反应起始阶段,分子筛骨架铝原子快速脱出,其晶体结构遭到严重破坏.随着反应的进行,分子筛硅铝比和结晶度皆有所增加,表明其骨架结构可能进行了重新排列.75℃下,0.10 mol/L柠檬酸处理2 h的脱铝分子筛样品,与NaY分子筛样品相比,其骨架硅铝比增加了0.6、外表面增加了17 m²·g^-1,脱铝同时产生了大量无定形硅.     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.