丙烯酸酯改性水性聚氨酯乳液的制备及性能研究

采用共聚的方法制备出丙烯酸酯改性的水性聚氨酯共聚乳液(PUA乳液),并对PUA乳液的制备方法和工艺、耐溶剂性、机械稳定性进行了初步的研究。结果表明,具有IPN结构的PUA乳液耐溶剂性、机械稳定性比水性PU有明显的提高。     

聚丙烯酸酯改性水性聚氨酯的制备

在回顾聚丙烯酸酯改性水性聚氨酯的研究历史基础上，系统地介绍了聚丙烯酸酯改性水性聚氨酯乳液（PUA）的制备方法，其中包括聚氨酯（PU）和聚丙烯酯（PA）的直接掺混法、PU和PA的乳液共聚法，接枝法，互穿网络法，核壳聚合法，对这些方法做了简单的评述，对其应用范围及前景进行了初步探讨。     

蒽醌型蓝色扩链剂及其PUA共聚物乳液的制备与性能

首先以1-甲氨基-4-溴-蒽醌和2-氨基-2-甲基-1,3-丙二醇为原料,通过取代反应合成了蒽醌型蓝色扩链剂1-(1,1-二(羟甲基))乙氨基-4-甲氨基蒽醌(HMEMAQ),并将其与N,N-二(2-羟乙基)丙烯酰胺作为扩链剂合成出聚氨酯预聚体,然后经与甲基丙烯酸甲酯和丙烯酸丁酯的接枝乳液共聚合制备出了性能稳定的共聚型蓝色聚氨酯-丙烯酸酯共聚物(PUA)乳液.然后用1H-NMR、FTIR、UV-Vis吸收光谱、粒度和电位分析、氙灯老化等方法对HMEMAQ的化学结构、PUA乳液及乳胶膜的性能进行了表征.研究发现,在N2气氛下,用偶氮类AIBN作为引发剂可以有效避免PUA乳液合成过程中生色基团的氧化变色现象.当AIBN用量达到不饱和单体的2 wt%时,接枝反应的单体转化率可达到99.9%.HMEMAQ用量对乳液的胶体性质和单体转化率没有明显影响.PUA聚合物和HMEMAQ的UV-Vis吸收光谱保持一致,最大吸收波长均为640.8 nm.与具有相同生色基团的共混型蓝色PUA乳胶膜相比,共聚型PUA乳胶膜的耐光色牢度和耐溶剂色牢度有明显的提高.     

有机硅改性聚氨酯丙烯酸酯细乳液的制备及性能

将自制的聚氨酯大单体与含乙烯基有机硅单体、丙烯酸酯进行共聚反应,通过合适的工艺条件,制备了一系列性能稳定的细乳液。研究了聚合方法、有机硅含量对共聚细乳液及胶膜性能的影响。结果表明,种子细乳液法制得的聚合物结构明确,细乳液粒径均在150 nm左右,分布指数约为0.07,有机硅的引入使乳液胶膜耐水性及耐高温性得到了明显提高。     

阳离子丙烯酸树脂乳液涂饰剂的合成研究

以丙烯酸二乙氨基乙酯及其它丙烯酸酯类、乙烯基类单体作为共聚单体,以过醋酸-双氧水为引发体系,采用核-壳乳液共聚方法,对阳离子丙烯酸树脂的合成进行了研究,结果表明;引发剂体系和乳化剂体系对乳液的性能、乳胶粒的形态结构、聚合物的性能以及工艺过程的平稳性至关重要。该项研究为阳离子丙烯酸系聚合物在制革业中的广泛应用奠定了基础。     

有机硅改性磺酸型聚氨酯/丙烯酸酯复合乳液的制备

将磺酸型聚酯多元醇、异佛尔酮二异氰酸酯(IPDI)和三羟甲基丙烷(TMP)在无有机溶剂参与的情况下进行预缩聚,以硅烷偶联剂γ-氨丙基三乙氧基硅烷(KH550)作为改性剂,加入双官能团单体甲基丙烯酸-β-羟乙酯(HEMA),得到含乙烯基和有机硅封端的聚氨酯作为种子乳液,然后与甲基丙烯酸甲酯(MMA)、丙烯酸丁酯(BA)混合单体共聚,合成了有机硅改性磺酸型聚氨酯/丙烯酸酯复合乳液。红外光谱的表征确定了有机硅改性磺酸型聚氨酯/丙烯酸酯复合乳液的化学结构;透射电子显微镜观察证实了此复合乳液具有明显的核壳结构;热重分析表明,经有机硅和丙烯酸酯改性后,胶膜的最大热失重温度提高了20℃,X射线衍射分析表明胶膜的结晶度降低,有利于提高膜的韧性。力学性能测试及吸水率测试结果表明,当有机硅含量为1.9%时,胶膜的拉伸强度最高达到25.03 MPa,断裂伸长率为328%,此时膜的吸水率最低。     

含氟聚氨酯-丙烯酸酯核壳乳液的制备及性能

以甲基丙烯酸羟乙酯封端的水性聚氨酯作为大分子单体,与甲基丙烯酸甲酯及甲基丙烯酸全氟烷基乙基酯在乳液中进行自由基共聚合,制备出具有核壳结构的水性含氟聚氨酯-丙烯酸酯乳液。通过激光粒度分析仪、FT-IR、DSC、TGA、接触角、力学等表征手段,对乳液及其乳胶膜的结构和性能进行了研究,还着重探讨了甲基丙烯酸全氟烷基乙基酯的含量对乳胶膜性能的影响,结果表明:所制得的材料具有预期结构,并且具有优异的表面性能和力学性能,氟单体的引入使乳胶膜的表面能大大降低,而力学性能明显提高。     

聚氨酯一聚丙烯酸酯共聚乳液的合成研究

以甲基丙烯酸β－羟乙酯封端的聚氨酯大分子单体与丙烯酸酯类单体进行乳液共聚，合成了以聚丙烯酸酯（PA）为主链、聚氨酯（PU）为侧链的接枝共聚物（PA－g－PU）乳液，用IR光谱和^1H NMR光谱对该聚氨酯大分子单体及PA－g－PU接枝共聚物进行了表征，并对影响聚氨酯－聚丙烯酸酯共聚合的因素进行了探讨。结果表明：聚氨酯大分子单体的加入对乳液聚合的速率造成较大的影响。该体系的表观活化自由能为99.39KJ/mol,Rp∝[I]^0.87,Rp∝[S]^0.12。     

聚氨酯/苯丙杂化乳液的合成、表征和特性及其在复膜胶中的应用

由聚氨酯(PU)预聚物、丙烯酸丁酯和苯乙烯单体的乳液聚合制备了聚氨酯-苯乙烯-丙烯酸酯(PUSA)杂化乳液,1H NMR显示所得的PU预聚物由烯烃基团封端。TEM表明,其粒径约为150 nm,且为颜色深浅不同的两部分所组成。随着PU含量的降低,杂化乳液的热稳定性增加。DSC分析表明,所得杂化乳液有单一的T g值,且处于聚氨酯和聚苯丙(PSA)乳液T g值的中间。当将得到的杂化乳液用于纸塑和塑塑复合时,其剥离强度分别为14.1 N/2.5 cm和12.2 N/2.5 cm。     

环状单体与乙烯基单体的杂化共聚

本文研究了在膦腈碱(t-BuP4)催化下各种环状单体和乙烯基单体的杂化共聚,发现己内酯、丙交酯或环碳酸酯与丙烯酸酯或甲基丙烯酸酯能够进行杂化共聚,但环硅氧烷与乙烯基单体、丙烯腈与内酯不能杂化共聚.研究表明,单体与活性中心的匹配决定了杂化共聚能否进行.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

化学计量中不确定度评定研究进展

测量不确定度是表征合理地赋予被测量之值的分散性的参数。本文针对化学计量不确定度评定基础模型仅适用于线性模型、概率分布为正态分布或缩放位移t分布等局限,介绍了近年来不确定度评定的研究热点:蒙特卡罗方法(Monte Carlo Method,MCM),不确定度评定的来源、评定概念、评估方法及其发展过程,扩大了测量不确定度评定与表示的适用范围。     

微量钙的测定方法研究进展

介绍了1995-2006年期间测定微量和痕量钙的方法,如电感耦合等离子体-原子发射光谱法、原子吸收光谱法以及离子色谱法等的工作原理和特点,并说明了其测定微量钙的应用领域。并对微量钙的测定技术进行了展望(引用文献55篇)。