A DSC study of benzoic acid: a suggested calibrant compound

It has been found that cobalt(II, III) oxide, Co₃O₄, lowers the thermal decomposition temperature of Na₂S₂O₈ and K₂S₂O₈ by about 25°C by catalysis, and it therefore acts as a P-type semiconductor at high temperature and atmospheric (air) pressure. Also, this oxide reacts at high temperature with sodium or potassium pyrosulfates to form thermally stable sodium cobalt disulfate, Na₂Co(SO₄)₂ and potassium cobalt trisulfate, K₂Co₂(SO₄)₃, respectively. Binary systems, consisting of a 1 : 3 mole ratio (oxide : persulfate), are established as representing the solid state stoichiometric reaction. X-Ray diffractometry is employed to identify intermediate and final reaction products in general. All calculations are based on data obtained from TG, DTG and DTA curves.     

High temperature reactions of titanium(IV) oxide with some alkali persulfates and their decomposition products

The solid state reactions between TiO₂ and Na₂S₂O₈ or K₂S₂O₈ have been investigated using TG, DTG, DTA, IR, and X-ray diffraction studies in the range of 20 to 1000°C.It has been shown that TiO₂ reacts stoichiometrically (1 : 1) with Na₂S₂O₈ in the range of 160 and 220°C forming the complex sodium monoperoxodisulfato—titanium(IV) as characterized by IR and X-ray analysis. The new complex then decomposes into the reactants above 190°C.An exothermic reaction has been observed between TiO₂ and molten K₂S₂O₇ at mole ratio 1:2 respectively and higher, in the range of 280 and 350°C. The IR and X-ray analyses have shown the formation of a complex namely, potassium tetrasulfato titanium(IV) for which the formula and structure have been proposed. This complex decomposes at higher temperatures into K₂SO₄ and a mixed sulfate of potassium and titanium. The mixed sulfate melts at 620°C and decomposes into K₂SO₄, TiO₂, and the gaseous SO₃.On the other hand, Na₂S₂O₈ decomposes in a special mode producing a polymeric product of Na₁₀S₉O₃₂. Decomposition of this species occurs after melting at 560°C into Na₂SO₄ and sulfur oxides. The decomposition reaction has been proved to be catalysed by TiO₂ itself.     

Solid-state reactions between alkali persulfates and oxides of corundum structure

The effects of three corundum structure oxides, α-Al₂O₃, α-Cr₂O₃, and α-Fe₂O₃, on the thermal decomposition of sodium and potassium peroxodisulfates (persulfates) under non-isothermal static air conditions and using various oxide/persulfate molar ratios, have been thermoanalytically investigated. Compounds such as Na₃Al(SO₄)₃, K₃Al(SO₄)₃, Cr₂(SO₄)₃, K₃Cr(SO₄₃, and Na₃Fe(SO₄)₃ are identified by X-ray diffractometry and conventional chemical analysis. The molar ratios as well as temperatures of the stoichiometric formation for these compounds have been established. At higher temperatures, α-Al₂O₃ acts as a promoter catalyst for the decomposition of pyrosulfate to sulfate, whereas α-Cr₂O₃ behaves as a retarder for the decomposition of persulfate. A eutectic mixture is formed between K₃Al(SO₄) and K₂SO₄ at 675°C. Also, K₃Fe(SO₄)₃ is identified as two crystalline phases.     

Struktur und thermisches Verhalten von Gadolinium(III)-sulfat-Octahydrat Gd2(SO4)3 · 8 H2O

Structure and Thermal Behaviour of Gadolinium(III)-sulfate-octahydrate Gd₂(SO₄)₃ · 8 H₂O . Gd₂(SO₄)₃ · 8 H₂O crystallizes monoclinic with space group C2/c and the lattice constants a = 13.531(7), b = 6.739(2), c = 18.294(7) Å, β = 102.20(8)°. In the structure Gd is coordinated by 4 oxygen atoms of crystal water and 4 oxygens of sulfate giving rise to a distorted square antiprism. During DTA-TG-experiments the title compound first loses crystal water in a two-step mechanism in the temperature range 130–306°C. The resulting Gd₂(SO₄)₃ is amorphous and recrystallization occurs in the range 380–411°C. The so-obtained low-temperature modification β-Gd₂(SO₄)₃, undergoes a monotropic phase transition at about 750°C to the high-temperature form α-Gd₂(SO₄)₃. The powder pattern of this modification was indexed based on monoclinic symmetry with space group C2/c and lattice constants a = 9.097(3), b = 14.345(5), c = 6.234(2) Å, β = 97.75(8)°. The hightemperature modification of gadolinium-sulfate shows decomposition to Gd₂O₂SO₄ at 900°C and, subsequently, decomposition at 1 200°C yields the formation of C-Gd₂O₃.     

Phase ratios in the K2O-V2O4-SO3 system at high sulfur trioxide concentrations

Phase ratios in the three-component oxide system K₂O-V₂O₄-SO₃ in the region of the sulfur trioxide concentrations corresponding to its concentrations in the active component of vanadium catalysts for SO₂ to SO₃ conversion have been studied using powder X-ray diffraction, IR spectroscopy, microscopy, and chemical analysis. Four individual compounds (K₂VO(SO₄)₂, K₂(VO)₂(SO₄)₃, K₂VO(SO₄)₂S₂O₇, and K₂(VO)₂(SO₄)₂S₂O₇) and K₂(VO)₂(SO₄)₂S₂O₇ and VOSO₄-base solid solutions of composition K₂(VO)_2+x (SO₄)_2+x S₂O₇ (0 ≤ x ≤ 1.5) were found in the system. K₂VO(SO₄)S₂O₇ and K₂(VO)₂(SO₄)₂S₂O₇ lose their sulfur trioxide when heated above 350°C under an inert atmosphere, and convert to K₂VO(SO₄)₂ and K₂(VO)₂(SO₄)₃, respectively. This implies that K₂VO(SO₄)₂S₂O₇ and K₂(VO)₂(SO₄)₂S₂O₇, as well as K₂(VO)_2+x (SO₄)_2+x S₂O₇ solid solution, cannot exist in the active component of real industrial catalysts.     

The phase diagram of the system La2(SO4)3Ag2SO4

The phase diagram of the system La₂(SO₄)₃Ag₂SO₄ was studied by DTA, XRD, SEM, and optical methods. One double salt is formed at 67 mole% La₂(SO₄)₃ and this melts incongruently at 876±6°C. A eutectic is formed at 8 mole% La₂(SO₄)₃ and at a temperature of 618±3°C. Suppression of decomposition was effected by the sealed tube method, but some reference is made to experiments conducted with a flowing atmosphere of SO₃, SO₂ and O₂.     

Thermal and X-ray diffraction investigations of some lanthanum(III) and neodymium(III) oxide-alkali persulfate binary systems

Different molar ratios of La₂O₃ or Nd₂O₃:Na₂/K₂S₂O₈ have been prepared, and the results of their TG and DTA investigations, under an atmosphere of static air, are reported. The effects of either La₂O₃ or Nd₂O₃ on the thermal decomposition of the persulfates from ambient to 1050°C, using a derivatograph, have been studied. It has been found that La₂O₃ lowers the initial decomposition temperatures of these alkali persulfates through catalytic activity. Nd₂O₃ shows little or no catalytic effect and therefore it acts as an insulator. Intermediate and final products are identified by X-ray diffraction analysis. The stoichiometric molar ratios of the solid state reactions are 1:3::R₂O₃:M₂S₂O₈. (R = La or Nd. M = Na or K), which give double salts of formulae: NaLa(So₄)₂, KLa(SO₄)₂, NaNd(SO₄)₂, and KNd(SO₄)₂. No sulfates or oxysulfates of lanthanum or neodymium have been identified.     

Stages of thermal decomposition of sodium oxo-salts of sulphur

Thermal behaviour of sodium oxo-salts of sulphur: Na₂SO₄, Na₂S₂O₇, Na₂S₂O₆, Na₂SO₃, Na₂S₂O₅, Na₂S₂O₄, Na₂S₂O₃, Na₂S₃O₆ and of sulphides Na₂S and Na₂S₂ was studied on heating up to 1000°C. The experiments were performed with anhydrous compounds obtained from commercial products by recrystallisation and dehydration. The stage mechanisms of decomposition of anionic sub-lattices of the salts have been proposed basing on the Górski’s morphological classification of simple species. The thermal stability and the stage decomposition mechanisms were correlated with the structure and the potential chemical properties of the salt anions. The thermal decomposition processes were studied by means of thermal analysis, and the decomposition products were identified by means of X-ray phase analysis.     

Physicochemical Analysis of the System Zr(SO<Subscript>4</Subscript>)<Subscript>2</Subscript>–Na<Subscript>2</Subscript>SO<Subscript>4</Subscript>–H<Subscript>2</Subscript>SO<Subscript>4</Subscript>–H<Subscript>2</Subscript>O at 25°С

The solubility in the quaternary water–salt system Zr(SO₄)₂ · 4Н₂О–Na₂SO₄–H₂SO₄–H₂O at 25°C was studied. It was found that, in the system, there is crystallization of not only Na₂SO₄ and Zr(SO₄)₄ · 4H₂O, but also sodium sulfate zirconates Na₂Zr(SO₄)₂(OH)₂ · 0.3H₂O, Na₄Zr(SO₄)₄ · 3H₂O, and Na₂Zr(SO₄)₂ · 3H₂O and two new compounds, S₁ and S₂, which are presumably Na₂ZrO(SO₄)₂ · 2H₂O and Na₂Zr₂O₂(SO₄)₃ · 6H₂O.     

Synthesis and thermal decomposition of potassium peroxotitanate to K2Ti2O5

Potassium peroxotitanate was synthesized by the peroxo method. During the thermal decomposition K₂Ti₂O₅ can be obtained. The isothermal conditions for decomposition of K₂[Ti₂(O₂)₂(OH)₆]·3H₂O were determined on the base of DTA, TG and DSC results. DTA and TG curves were recorded in the temperature range 20 and 900°C at a heating rate of 10°C min^–1. The obtained intermediate compounds were characterized by means of quantitative analysis and IR spectroscopy. The mechanism of thermal decomposition of K₂[Ti₂(O₂)₂(OH)₆]·3H₂O to K₂Ti₂O₅ was studied. The optimal conditions for obtaining K₂Ti₂O₅ were determined (770°C for 10 h).     

Effects of nickel(II) oxide on the thermal decomposition of alkali persulfates

The thermal decomposition of Na₂S₂O₈ and K₂S₂O₈ has been studied derivatographically in the presence of NiO at various molar mixtures. Experiments have proved that the first decomposition stage (persulfate into pyrosulfate) is independent of the amount of the oxide present. During the second decomposition stage (pyrosulfate into sulfate) which occurs in the melt, NiO plays the role of lowering the melting, the initial and final decomposition temperatures of pyrosulfates. The lowest melting temperatures recorded for Na₂S₂O₈ and K₂S₂O₈ are 320 and 280°C, respectively.A mechanism has been proposed to describe the catalytic action of NiO on the thermal decomposition of alkali pyrosulfates. The mechanism makes use of the semiconductivity of NiO and the availability of electron-rich centers in the pyrosulfate group to help the formation of an adsorption complex between them.NiO reacts to some extent with alkali pyrosulfates forming the yellow NiSO₄ and alkali sulfates as separate products.NiO and NiSO₄ form eutectic mixtures with alkali sulfates melting at temperatures lower than those of the pure salts.     

Studies on lanthanoid sulphites: V. thermal decomposition of cerium and neodymium sulphites

The preparation and thermal behaviour of Ce₂(SO₃)₃· 3H₂O, Nd₂(SO₃)₃·6H₂O and Nd₂(SO₃)₃ have been studied. Cerium sulphite undergoes first dehydration which is followed by decomposition to CeO₂ in the temperature range 500 – 850 °C. The decomposition involves two intermediate phases both in air and nitrogen. According to the TG curves the phases in air are Ce₂(SO₃)₂SO₄ and Ce₂SO₃(SO₄)₂. In nitrogen, Ce₂O₂SO₄ was identified and this provides a synthetic route to cerium oxysulphate.Neodymium sulphite decomposes to Nd₂O₂SO₄ when heated in air or in nitrogen up to 950°C. The intermediate levels observed do not correspond to single phases, and the reaction mechanism depends strongly on the experimental conditions.     

Evolved gas analyses on a mixed valence copper(I,II) complex salt with thiosulfate and ammonia by in situ TG-EGA-FTIR and TG/DTA-EGA-MS

Thermal decomposition of a mixed valence copper salt, Na₄[Cu(NH₃)₄][Cu(S₂O₃)₂]₂·0.5NH₃ (1) prepared from pentahydrates of sodium thiosulfate and copper sulphate of various molar ratios in 1:1 v/v aqueous ammonia solution, has been studied up to 1,000 °C in flowing air by simultaneous thermogravimetric and differential thermal analysis coupled online with quadrupole mass spectrometer (TG/DTA-MS) and FTIR spectrometric gas cell (TG-FTIR), in comparison. Compound 1 releases first but very slowly some of the included ammonia till 170 °C, then simultaneously ammonia (NH₃) and sulphur dioxide (SO₂) from 175 to 225 °C, whilst the evolution of SO₂ from thiosulfate ligands continues in several overlapping stages until 410 °C, and is escorted by explicit exothermic heat effects at around 237, 260, 358 and 410 °C. The former two exothermic DTA-peaks correspond to the simultaneous degradation and air oxidation processes of excess thiosulfate anions not reacted by formation of copper sulfides (both digenite, Cu_1.8S and covellite, CuS, checked by XRD) and sodium sulfate, while the last two exothermic peaks are accompanied also by considerable mass gains, as the result of two-step oxidation of copper sulfides into various oxosulfates. The mass increase continues further on until 580 °C, when the sample mass begins to decrease slowly, as a continuous decomposition of the intermediate copper oxosulfates, indicated also by re-evolution of SO₂. At 1,000 °C, a residual mass value of 64.3% represents a stoichiometric formation of Cu^IIO and anhydrous Na₂SO₄.     

Phase equilibria in systems of gallium sulfate with lithium or sodium sulfate

The phase diagrams of binary systems of gallium sulfate with lithium or sodium sulfate were studied for the first time. The Li₂SO₄–Ga₂(SO₄)₃ system is of the eutectic type. The coordinates of the eutectic are (548°C, 30 mol % Ga₂(SO₄)₃). The region of a solid solution based on the high-temperature modification α-Li₂SO₄ is small. In the Na₂SO₄–Ga₂(SO₄)₃ system, compound Na₃Ga(SO₄)₃ forms, which melts incongruently at 585°C. The coordinates of the eutectic are (538°C, 17 mol % Ga₂(SO₄)₃). The region of a solid solution based on α-Na₂SO₄ reaches 8 ± 1 mol % Ga₂(SO₄)₃. The X-ray powder diffraction pattern of Na₃Ga(SO₄)₃ was indexed in a tetragonal unit cell with the parameters a = 9.451(3) Å and c = 7.097(3) Å; the unit cell parameters for an aluminum-containing analog, Na₃Al(SO₄)₃, are a = 9.424(5) Å and c = 7.053(3) Å.     

Structural Characterization of Some Coinage Metal(I) Thiosulfate Complexes, $\rm M^{1}_{a}M\rm ^{2}_{b}(X_{c}) (S_{2}O_{3})_{d}(\cdot eS)$ (M1 = Group 1 Cation,X = Univalent Anion,M2 = CuI,AgI, S = Solvent)

Building on previous single crystal X‐ray structure determinations for the group 1 salts of complex thiosulfate/univalent coinage metal anions previously defined for (NH₄)₉AgCl₂(S₂O₃)₄, NaAgS₂O₃·H₂O and Na₄[Cu(NH₃)₄][Cu(S₂O₃)₂]·NH₃, a wide variety of similar salts, of the form , M¹ = group 1 metal cation, M² = univalent coinage metal cation (Cu, Ag), (X = univalent anion), most previously known, but some not, have been isolated and subjected to similar determinations. These have defined further members of the isotypic, tetragonal series, for M¹ = NH₄, M² = Cu, Ag, X = NO₃, Cl, Br, I, together with the K/Cu/NO₃ complex, all containing the complex anion [M²(SSO₃)₄]^7? with M² in an environment of symmetry, Cu, Ag‐S typically ca. 2.37, 2.58Å, with quasi‐tetrahedral S‐M‐S angular environments. Further salts of the form , n = 1‐3, have also been defined: For n = 3, M² = Cu, M¹/x = K/2.25 or 1 5/6, NH₄/6, (and also for the (NH₄)₄Na/4H₂O·MeOH adduct) the arrays take the form with distorted trigonal planar CuS₃ coordination environments, Cu‐S distances being typically 2.21Å, S‐Cu‐S ranging between 105.31(4)–129.77(4)°; the silver counterparts take the form for M¹ = K, NH₄. For n = 2, adducts have only been defined for M² = Ag, the anions of the M¹ = Na, K adducts being dimeric and polymeric respectively: Na₆[(O₃SS)₂Ag(μ‐SSO₃)₂Ag(SSO₃)]·3H₂O, K₃[Ag(μ‐SSO₃)₂]_(∞|∞)·H₂O; a polymeric copper(I) counterpart of the latter is found in Na₅Cu(NO₃)₂(S₂O₃)₂ ≡ 2NaNO₃·Na₃[Cu(μ‐SSO₃)₂]_(∞|∞). For n = 1, NaAgS₂O₃, the an‐ and mono‐ hydrates, exhibit a two‐dimensional polymeric complex anion in both forms but with different contributing motifs. (NH₄)₁₃Ag₃(S₂O₃)₈·2H₂O takes the form (NH₄)₁₃[{(O₃SS)₃Ag(μ‐SSO₃)}₂Ag], a linearly coordinated central silver atom linking a pair of peripheral [Ag(SSO₃)₄]^7? entities. In Na₆[(O₃SS)Ag(μ‐SSO₃)₂Ag(SSO₃)]·3H₂O, the binuclear anions present as Ag₂S₄ sheets, the associated oxygen atoms being disposed to one side, thus sandwiching layers of sodium ions; the remarkable complex Na₅[Ag₃(S₂O₃)₄]_(∞|∞)·H₂O is a variant, in which one sodium atom is transformed into silver, linking the binuclear species into a one‐dimensional polymer. In (NH₄)₈[Cu₂(S₂O₃)₅]·2H₂O a binuclear anion of the form [(O₃SS)₂Cu(μ‐S.SO₃)Cu(SSO₃)₂]^8? is found; the complex (NH₄)₁₁Cu(S₂O₃)₆ is 2(NH₄)₂(S₂O₃)·(NH₄)₇[Cu(SSO₃)₄]. A novel new hydrate of sodium thiosulfate is described, 4Na₄S₂O₃·5H₂O, largely describable as sheets of the salt, shrouded in water molecules to either side, together with a redetermination of the structure of 3K₂S₂O₃·H₂O.     

Raman spectroscopy evidence of 1:1:1 complex formation during dissolution of WO3 in a melt of K2S2O7:K2SO4

Highly inert yellow solid WO₃ was found to be soluble in considerable amounts in molten K₂S₂O₇ at elevated temperatures (∼650 °C), if only similar molar amounts of sulfates were also present. The dissolution reaction of WO₃ into a melt consisting of a 1:1 molar mixture of K₂S₂O₇ and K₂SO₄ was studied in detail, and Raman spectroscopy was used to characterize the products. In combination with single crystal X-ray crystal structure determination, it was shown that a new dimeric compound, K₈[{W^VIO₂(SO₄)₂}₂(μ-SO₄)₂], was formed and its assigned Raman spectrum at room temperature is given. The WO₂²⁺ cores of the dimeric complex have their symmetrical and antisymmetrical stretching modes ν₁(WO₂²⁺) and ν₃(WO₂²⁺) at around 1054 (strong) and 1042 (weak), and the bending mode ν₂(WO₂²⁺) at around 292 (medium intensity), respectively (positions given in cm⁻¹).     

Oxidizing Elemental Platinum with Oleum under Harsh Conditions: The Unique Tris(disulfato)platinate(IV) [Pt(S2O7)3]2− Anion

For the first time, direct oxidation of elemental platinum by a mineral acid to its tetravalent state was observed in course of the reaction of platinum with oleum (65 % SO₃) in the presence of barium carbonate. The reaction has been carried out in torch‐sealed glass ampoules at 160 °C and gave yellow single crystals of Ba[Pt(S₂O₇)₃](H₂SO₄)_0.5(H₂S₂O₇)_0.5 (triclinic, P$\bar 1$ , Z=2, a=992.05(2), b=1069.07(3), c=1114.22(3) pm, α=69.49(7), β=72.96(2), γ=72.93(1)°, V=1033.95(5) ų). The structure of Ba[Pt(S₂O₇)₃](H₂SO₄)_0.5(H₂S₂O₇)_0.5 exhibits the unique tris‐(disulfato)‐platinate anion [Pt(S₂O₇)₃]^2? with three chelating disulfate groups coordinated to the platinum atom. Charge balance is achieved by the Ba²⁺ ions, which are coordinated by (S₂O₇)^2? groups from the platinate complex and by disordered sulfuric acids and disulfuric acid molecules. Thermal decomposition of the bulk material revealed elemental platinum and barium sulfate as decomposition residual.     

Thermoanalytical behavior of cadmium(II) oxide—alkali persulfate binary systems

The non-isothermal behavior of two binary CdO—persulfate systems has been investigated. The molar ratios and T_i—T_f are established. The temperatures for the α- to β-Na₂SO₄ phase transition, as well as for α- to β- to γ-CdSO₄ of the CdONa₂S₂O₈ system have been fixed. No evidence for the occurrence of the β- to γ-CdSO₄ polymorphic trans-formation has been obtained from the reaction of the CdOK₂S₂O₈ system. This is because of the formation of a CdSO₄/K₂SO₄ eutectic mixture which melts at 653°C, i.e., before the β- to γ-phase change transition, which usually occurs later. No basic cadmium sulfate has been identified. The excess cadmium oxide acts as a p-type semiconductor which accelerates the thermal decomposition of pyrosulfates.     

Zum System V2O5?K2SO4

The phase diagram of the system V₂O₅? K₂SO₄ was established by means of X-ray diffraction and DTA. An endothermal reaction leads to the compound 5V₂O₅·3K₂SO₄ which melts at 510°C, crystallizes needle-shaped and forms hydrates. Eutectics occur at 31 (505°) and 55 mole-% K₂SO₄ (455°C).     

Zur Kenntnis von Natriumarseniten im Dreistoffsystem Na2O?As2O3?H2O bei 6°C

Concerning Sodium Arsenites in the Three Component System Na₂O? As₂O₃? H₂O at 6°C Four phases Na₂(H₂As₄O₈) 1c , NaAsO₂ · 4 H₂O 2c , Na₂(HAsO₃) · 5 H₂O 3c , and Na₅(HAsO₃)(AsO₃) · 12 H₂O 4c have been identified in the system Na₂O? As₂O₃? H₂O at 6°C and characterized by X-ray structural analysis. Polymetaarsenite anions, adopt in 1c and 2c , respectively, octet or doublet single chains.