聚乙二醇蓄热调温性能及其在功能纺织品上的应用

对聚乙二醇(PEG)的自身交联及其与纤维素纤雏之间的交联反应进行了研究，探讨了交联前后PEG热活性的变化，并对PEG在焙烘交联时的受热稳定性以及分子量对热活性的影响进行了讨论。研究表明，PEG发生交联反应后，热性能参教产生偏移，热活性降低；热活性与分子量有直接关系；过高的焙烘温度将导致PEG氧化降解，热活性下降。在适宜的工艺条件下，纺织品经PEG后整理可获得热活性。     

聚富马酸丁二酯的水热老化行为研究

研究了聚富马酸丁二酯(PBF)的水热老化行为,采用凝胶渗透色谱法(GPC)、力学性能测试,示差扫描量热法(DSC)和全反射红外光谱(ATR-FTIR)研究了老化过程中PBF的分子量、力学性能、热性能和表面化学基团含量的变化.研究结果表明,PBF在30℃下具有良好的耐老化性能.温度对PBF老化行为的影响显著,水热老化温度升至60℃,PBF各项力学性能急剧下降,老化20天后样品在水中断裂并形成碎片,力学性能完全丧失,同时数均分子量下降了50%.80℃水热老化5天,样品即断裂并形成碎片,失去结构的完整性,数均分子量下降了87%.老化过程中碳碳双键的含量未发生明显变化,老化降解的机理是水的增塑、溶胀以及酯键水解,聚合物分子链断裂,分子量下降.     

煤改性聚乙烯塑料的降解性能及其机理探讨

通过对力学性能、红外光谱、粘均分子量及扫描电镜的分析,研究了煤/聚乙烯塑料在室内加速老化实验中的降解性能,并运用降解机理对实验过程进行解析及验证。结果表明,煤降解剂引发的交联和降解反应控制了薄膜的强度,使其柔韧性一直降低,且在整个120h光照过程中,断裂伸长率一直呈下降趋势;72h前是聚合物的氧化诱导期及衰变期,之后进入完全降解期。煤在改性塑料光照过程中引发自由基反应,引入羰基,导致聚乙烯大分子断链降解;共聚物的粘均分子量整体呈降低趋势,说明光照促进聚合物的降解,降解和交联交替控制着反应。煤/聚乙烯的光降解过程遵循链引发、链增长、链终止反应机理,在煤大分子光催化作用下,改变了聚乙烯常规光降解过程,加速了聚乙烯大分子断链和分子量降低。运用煤/聚乙烯塑料降解机理,能够解释样品力学性能变化、化学结构中羰基指数变化、分子量降低及降解过程中的现象和规律。     

热稳定剂对PVC紫外光老化过程中微观结构及宏观性能演变的影响

通过UV-Vis、FTIR、DSC、以及色差、力学性能的测试表征,实时追踪分析了在紫外光老化过程中,含Pb、Sn以及Ca-Zn热稳定剂的PVC体系微观结构和宏观性能的演变过程.结果表明,在相同光老化条件下,PVC/Pb、PVC/Sn和PVC/Ca-Zn体系的微观结构变化规律基本一致,过程中主要的化学反应是,大分子吸收光能后,发生脱HCl生成共轭双键的反应、生成羰基的氧化反应、交联反应和降解反应;不同热稳定剂的作用,主要表现在对于微观结构变化的幅度和动力学过程的影响不同.相应地,3种体系的外观色差和力学性能的变化规律也相似,但色差的变化程度和速度以及老化后力学性能的保持率因所含热稳定剂的不同而不同,其中含Sn体系的颜色稳定性最好,含Pb体系的力学性能保持率最高。     

二维相关红外光谱法及标准线性固态模型对天然橡胶热氧老化机理的研究

对天然橡胶复合材料进行了不同时间下的热氧加速老化实验并分析其老化机理.采用红外测试研究天然橡胶在热氧老化过程中可能的基团变化规律,同时对不同老化时间下的红外结果进行二维相关分析,发现老化产物的生成速率依次为酯过氧化物醚;核磁交联密度测试表明总交联密度(XLD)与网链分子量(Mc)及横向弛豫时间(T2)有很好的对应关系,XLD随着老化时间的增加而增加,即天然橡胶热氧老化过程中交联反应占主导地位;示差扫描量热(DSC)测试发现,随着老化时间的增加,玻璃化转变温度(Tg)升高,玻璃化转变区变宽,表明交联反应占主导地位,与核磁交联密度测试结果一致.通过对天然橡胶进行压缩应力松弛实验,采用修正的标准线性固态模型(SLS模型)进行拟合分析,发现在短时热氧老化过程中,老化以氧化和交联反应为主,与核磁交联密度及DSC实验结果一致.     

聚对苯二甲酰对苯二胺纤维的热老化行为与机理研究

在250～400℃空气中对自由状态下对位芳纶进行等温热老化处理,采用万能材料试验机、红外光谱法、广角X射线衍射法、声速法和特性黏数法表征了老化过程中力学性能和结构的变化.结果表明,在老化初期,由于分子链的解取向,强度随时间快速下降;随后的热分解使强度随老化时间继续降低,符合二级反应动力学模型,其热老化表观活化能为32.4kJ/mol.老化样品的强度随温度升高显著下降,但高于350℃时热交联反应变得明显,同时结晶度增大和结晶结构完善,使强度的损失速率减小.老化样品的模量随老化温度的升高而增大,低于350℃时,非晶态分子链的解取向占优,模量较未热老化样品低;升高至350℃时,结晶结构完善占优,表现在第二类晶格畸变参数降低、表观微晶尺寸增大,特别是微晶横向融合使a,b轴方向尺寸显著增大,模量明显高于未老化样品.     

含羧酸稀土光敏剂降解PVC塑料的可降解研究

以羧酸共生稀土作为PVC塑料紫外光氧化降解的光敏剂,采用人工加速老化实验、户外曝晒实验等方法进行降解试验,并用红外光谱,紫外光谱和凝胶色谱等方法对含羧酸共生稀土光敏剂可降解PVC塑料的可降解性能进行了研究。初步探讨了羧酸共生稀土敏化PVC膜光氧化降解的作用机理。结果表明,羧酸共生稀土(如La、Ce、Pr等)对PVC分子的结构具有明显的光敏化降解作用,并具有抑制PVC在光照过程中发生交联的作用。     

含羟酸稀土光敏剂降解PVC塑料的可降解研究

以羧酸共生稀土作为PVC塑料紫外光氧化降解的光敏剂,采用人工加速老化实验、户外曝晒实验等方法进行降解试验,并用红外光谱,紫外光谱和凝胶色谱等方法对含羟酸共生稀土光敏剂可降解PVC塑料的可降解性能进行了研究。初步探讨了羧酸共生稀土敏化PVC膜光氧化降解的作用机理。结果表明,羟酸共生稀土（如La、Ce、Pr等）对PVC分子的结构具有明显的光敏化降解作用,并具有抑制PVC在光照过程中发生交联的作用。     

完全交替结构乙烯-丙烯共聚物的制备与表征

对顺-1,4含量为100%的高顺式聚异戊二烯(HCPI)进行加氢反应,得到了序列结构高度规整的乙烯-丙烯交替共聚物(alt-EP).所用的HCPI有适当的分子量(Mn=41×104)和极窄的分子量分布(Mw/Mn=1.02).HCPI的加氢反应以环烷酸镍和三异丁基铝为催化剂,在60℃和4.0MPa氢压的条件下反应3h,加氢产物的加氢度为100%.GPC测试结果显示所得乙烯-丙烯交替共聚物保持了窄分布的特点,表明HCPI加氢后未发生交联和降解反应;NMR,FTIR和广角X射线衍射测试结果表明此乙烯-丙烯交替共聚物具有高度规整的序列结构,为完全交替结构的乙烯-丙烯共聚物.并通过TGA和DSC对乙烯-丙烯交替共聚物的热性能进行了表征.     

微量氧氛围中八乙烯基POSS低温(180℃)热氧老化机理研究

通过1 H-NMR,13 C-NMR,29 Si-NMR表征物质老化前后结构变化;采用FTIR,MALDI-TOF,ESR,TG-IR联用,DSC等分析手段跟踪老化过程中特征基团、分子量、活性中心、质量损失和焓变情况,对八乙烯基POSS(OVPOSS)在180℃微量氧气氛围的热氧老化行为进行了研究.采用微量氧气方法以减少乙烯基基团热氧老化过程中的过氧化反应,以观察可能存在的其他反应机理.实验表明老化过程中不饱和双键逐渐转化成饱和单键,老化过程存在C自由基中心和放热效应,且分子量增大趋势明显,质量变化略微,说明八乙烯基POSS在微量氧气氛围中的低温(180℃)热氧老化过程存在自由基聚合历程.     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.     

Understanding the Diels-Alder reactivity of 1,2-azaborine analogues

The Diels-Alder reactivity of 1,2-heteroborines (H₄C₄B(H)X, X?=?NH, PH, AsH; O, S, Se) has been computationally explored by means of Density Functional Theory (DFT) calculations. The influence of the HB?=?X fragment on the reactivity of the system has been quantitatively analyzed in detail by means of the so-called Activation Strain Model (ASM) of reactivity. It is found that the interaction between these species and the dienophile is significantly stronger than that computed for their all-carbon isoelectronic counterpart, benzene. In addition, the strain energy plays a key role in the observed reactivity trends. The role of the aromaticity strength of these heteroarenes on the reactivity is also assessed.     

Synthesis of N-substituted carbazolones from α-iodo enaminones via Pd(0)-catalyzed intramolecular coupling under microwave irradiation

A variety of N-aryl and N-alkyl carbazolones were conveniently achieved in good to high yields via Pd₂(dba)₃-mediated intramolecular coupling of N-substituted α-iodo enaminones under microwave irradiation. The Pd(0)-catalyzed cyclization was found to proceed favorably with the more electron-deficient phenyl ring during the reactions involving unsymmetrical N,N-diaryl α-iodo enaminones. This unique property enables the construction of carbazolone skeleton containing nitro substituted benzenoid ring.     

Synthesis of substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles by intramolecular nitrilimine cycloaddition

Both substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles have been synthesized by the 3+2 intramolecular dipolar cycloaddition of nitrilimines to alkynes. This cyclization has been extended to more versatile 3-bromo derivatives by the use of alkynylbromides as dipolarophiles.     

Catalyst free,visible-light promoted photoaddition reactions between C60 and N-trimethylsilylmethyl-substituted tertiary amines for synthesis of aminomethyl-1,2-dihydrofullerenes

An efficient and benign method for the preparation of aminomethyl-substituted fullerenes has been developed. The process, involving catalyst free, visible-light irradiation of 10% EtOH-toluene solutions containing fullerene C₆₀ and N-trimethylsilylmethyl-substituted amines by using a 20 W compact fluorescent lamp, leads to formation of aminomethyl-substituted fullerene adducts in a highly efficient manner. The photoaddition reaction takes place via a pathway initiated by visible light absorption by C₆₀, followed by SET from the amine to the triplet excited state of C₆₀. Ethanol-promoted desilylation of the resulting a minimum radical then generates the corresponding α-amino radical which couples with the C₆₀ radical anion to form the anion precursor of the fullerene adducts. The new approach using visible-light takes place under mild conditions and it does not require the use of photocatalysts. Thus, the method developed in this effort could broadens the range of functionalized fullerene derivatives that can be readily prepared.     

Highly efficient and stereoselective cycloaddition of nitrones to indolyl- and pyrrolylacrylates

The reactions of various nitrones with indolyl- and pyrrolylacrylates proceeds regioselectively with high diastereoselectivity in the case of aldonitrones, and represents an effective method for obtaining new indolyl- and pyrrolyl-substituted isoxazolidine carboxylates stabilized by weak (CH?O) and moderate (NH?N) strength intramolecular hydrogen bonding. The resulting cycloadducts exhibit promising in vitro anti-influenza activities.     

Transition metal-free direct amination of benzoxazoles using formamides as nitrogen sources

A transition metal-free method for the direct amination of benzoxazoles using formamides as nitrogen sources is reported, which was mediated by an inexpensive and environmentally friendly tetrabutylammonium iodide/tert-butyl hydroperoxide system and gave the 2-aminobenzoxazole derivatives with moderate to good yields.     

l-Proline-catalyzed five-component domino reaction leading to multifunctionalized 1,2,3,4-tetrahydropyridines

Multifunctionalized 1,2,3,4-tetrahydropyridines are concisely synthesized in good yields via l-proline-catalyzed or l-proline/FeCl₃-cocatalyzed one-pot multicomponent reactions (MCRs). The MCRs involve a domino hydroamination/prins reaction/Mannich-type reaction/intramolecular dehydration-cyclization process. The molecular structure of 5baa, one of multifunctionalized 1,2,3,4-tetrahydropyridines, was confirmed by single-crystal X-ray diffraction.     

Exploring the scope of the Gewald reaction: Expansion to a four-component process

An efficient four-component reaction was developed to take advantage of the reactivity of the 2-aminothiophene-3-carbonitrile functionality, which is obtained during the classical three-component Gewald reaction. Various α-methylene bearing ketones were reacted with malononitrile, elemental sulfur, and aryl/heteroarylnitrile derivatives in t-BuOH/NaOH to afford 2-arylthieno[2,3-d]pyrimidin-4-amines in high yields. Preliminary studies revealed the photophysical properties of the products and their potential for use as metal sensors.