首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 46 毫秒
1.
聚电解质PDDA/PSS层层自组装膜的渗透汽化性能   总被引:1,自引:0,他引:1  
采用聚电解质层层自组装(LbL)技术, 在不同盐浓度下制备了聚(二烯丙基二甲基氯化铵)/聚苯乙烯磺酸钠(PDDA/PSS) 多层自组装膜, 并用于渗透汽化性能的研究. 重点考察了组装溶液中NaCl的浓度、组装层数及操作温度对自组装膜的异丙醇脱水性能的影响. 同时, 用扫描电镜观测了不同条件下制备膜的表面形貌. 结果表明, 在高NaCl含量的聚电解质溶液中只需组装几个双层的LbL膜, 即能获得较高的分离因子和较大的通量, 并解释了该LbL膜呈现反“trade-off”现象的原因.  相似文献   

2.
研究了一种光响应偶氮聚电解质(PEAPE)在不同pH值条件下的自组装,重点讨论了pH值对静电逐层自组装以及对光响应性能的影响.研究表明,在所研究的pH范围内,pH值越低,越有利于生成吸光度高的自组装膜,对应的自组装膜厚度也越大.红外光谱分析表明,偶氮聚电解质在不同pH溶液中存在不同的电离情况.pH值越低,用于自组装的溶液中的聚合物链上的电荷数越少,链构象越卷曲.解释了不同pH值条件下自组装膜吸光度和厚度差别的原因.  相似文献   

3.
银/聚电解质复合纳滤膜的制备及表征   总被引:2,自引:1,他引:1  
利用层层自组装技术(LbL),采用原位还原方法在聚醚砜(PES)基膜上制备了银/聚电解质复合纳滤膜.SEM分析表明:膜表面结构致密,Ag粒子在复合膜中分布均匀,粒径100~200 nm,UV-vis图谱证明膜中粒子为Ag粒子,所得银/聚电解质纳滤膜呈现出优异的抗菌性能.[PSS/PDADMAC]3[PAS/PAH-Ag]3PSS膜对负二价离子显示出较高的截留性能,达到93%.  相似文献   

4.
以聚(乙烯-alt-马来酸酐)为原料,通过与R-(+)-α-苯乙胺的酰胺化反应,合成了一种新型的旋光聚电解质聚[乙烯-alt-R-N-(1-苯乙基)马来酰胺酸],利用红外吸收光谱、紫外吸收光谱、核磁共振氢谱和旋光度数据对其结构进行表征.聚[乙烯-alt-R-N-(1-苯乙基)马来酰胺酸]与聚二甲基二烯丙基氯化铵(PDDA)逐层静电自组装过程的紫外跟踪测试结果表明,带相反电荷的聚电解质间能够形成稳定增长的自组装膜,多层膜组装量随双层数指数增大.  相似文献   

5.
将壳聚糖(CS)溶液和透明质酸钠(SH)溶液共混,制备成CS-SH复合聚电解质溶液,并对溶液中所形成的胶粒进行了粒径分布和ZETA电位表征。用冷冻干燥法除去溶剂,制备了CS-SH复合聚电解质纳米纤维膜。用FT-IR对其结构进行分析,并用SEM对其形貌进行了表征。并将复合聚电解质纳米纤维膜作为疏水性药物紫杉醇(PTX)的载药体系,研究了其药物释放行为。结果表明,PTX在该载体中的释放较为平缓,这可以延长药物的有效时间,降低给药次数,增强治疗效果,降低药物的毒副作用。  相似文献   

6.
设计合成了甲基丙烯酸二甲氨基乙酯(DM)含量为9.69%的丙烯酸甲酯共聚物(CPA),将制得的5-氯甲基-8-羟基喹啉(CHQ)挂接到CPA上,得到季铵型高分子化8-羟基喹啉(CPA-HQ)后,与金属离子Li+配位得到CPA-HQ-Li.化合物结构通过红外、紫外和荧光光谱等表征.多层超薄膜用CPA-HQ-Li和聚阴离子电解质(全氟磺酸)通过静电自组装制得.自组装膜的紫外和荧光相对于溶液(溶剂为四氢呋喃)发生了红移,膜的紫外吸收强度随组装膜层数增加线性增大,荧光强度随膜层数增加线性递减.高分子化8-羟基喹啉锂溶液和自组装膜的紫外和荧光光谱与文献报道一致.实验结果表明这种材料可用于有机电致发光器件(OLEDs)的制备.  相似文献   

7.
采用杂化碳酸钙微球作为模板, 利用LbL技术, 选择聚苯乙烯磺酸钠(PSS), 烯丙基胺的盐酸盐(PAH)和二烯丙基二甲基胺盐酸盐(PADA)聚电解质, 分别组装了PAH/PSS(弱/强)聚电解质胶囊和PADA/PSS(强/强)聚电解质微胶囊. 除去模板后得到了球形良好、分散均匀的聚电解质微胶囊. 研究结果表明, 利用杂化碳酸钙微球作为聚电解质微胶囊的模板, 得到的微胶囊的囊壁厚而致密, 同时, 由于组装采用的聚电解质的种类不同, 囊壁的微观形貌有较大差异.  相似文献   

8.
合成了单体1,4-双(3-磺酰化丙氧基)-2,5-二碘苯与2,6-二乙炔基吡啶,利用Heck-Sonogashira偶联反应制备了间位聚亚吡啶基亚乙炔基共轭聚电解质m-PPYPE-SO3Na,对单体以及聚合物进行了红外光谱与核磁氢谱表征.测试了该共轭聚电解质m-PPYPE-SO3Na的紫外-可见吸收光谱与荧光发射光谱.研究了该共轭聚电解质的溶液光物理性质,发现该聚电解质具有荧光发射的溶剂依赖性以及浓度依赖性,在水溶液中存在聚集.在聚合物溶液浓度为1×10-6mol/L左右时,聚集发射基本消失,说明此时在溶液中聚合物的聚集程度已经比较低.该聚电解质在水溶液中与表面活性剂之间存在一定的相互作用,加入非离子型高分子表面活性剂聚乙烯吡咯烷酮(PVP)的聚合物水溶液荧光显著增强,表明该表面活性剂破坏聚电解质的聚集.该共轭聚电解质的溶液光物理性质表明其具有成为水溶性荧光探针的应用潜力.  相似文献   

9.
静电组装金纳米粒子制备局域表面等离子体共振传感膜   总被引:4,自引:1,他引:3  
采用聚电解质自组装技术制备局域表面等离子体共振(LSPR)传感膜的方法, 在玻璃基片上依次沉积聚电解质PDDA, PSS和PVTC, 并通过静电吸附构建胶体金纳米粒子自组装膜形成LSPR传感膜. 利用扫描电镜对LSPR传感膜表面形貌以及膜中金纳米粒子的粒径进行了表征, 同时通过紫外-可见消光光谱对其灵敏度和渗透深度等重要参数进行检测. 研究结果表明, 所制备的LSPR传感膜粒子分布均匀、单分散性好、稳定性高、重现性好; 消光峰位对样品溶液折射率的检测灵敏度为71 nm/RIU, 相应的峰强检测灵敏度为0.21 AU/RIU, 对表面吸附层的渗透深度约为16 nm.  相似文献   

10.
由聚电解质自组装多层膜制备微孔薄膜   总被引:1,自引:0,他引:1  
带有相反电荷的聚电解质通过静电作用交替沉积可以得到自组装多层膜,由于这种技术可操作性强,用途广泛,近十几年来已有了大量的研究.聚电解质多层膜在一定条件下可以形成纳米孔和微米孔.Fu等研究了聚丙烯酸和聚乙烯基吡啶组成的氢键自组装多层膜在碱溶液中溶去其中的聚丙烯酸后,剩下的聚乙烯基吡啶重构形成微孔薄膜.Mendelsohn等发现将聚丙烯酸和聚烯丙基胺自组装而成的多层膜浸入pH=2.4左右的溶液中可制备微孔薄膜.但这些方法并不能使强聚电解质多层膜形成多孔结构。  相似文献   

11.
真空薄膜浓缩装置的研制及应用研究   总被引:14,自引:0,他引:14  
袁珂  俞莉 《分析化学》2005,33(9):1358-1360
介绍了真空薄膜浓缩装置的构造、特征、工作原理及使用方法,并将真空薄膜浓缩法与旋转薄膜浓缩法的工作效率及对热敏性成分含量的影响进行了比较研究。结果表明,两法相比,前者具有仪器容量大、浓缩速度快、浓缩液受热时间短、操作简单及工作效率高等优点。  相似文献   

12.
For a system of flexible polymer molecules, the concepts of two concentrations, namely the segmental and the molecular concentrations, have been proposed in this paper. The former is equivalent to the volume fraction. The latter can be defined as the number of the gravity centers of macromolecules in a unit volume. The two concentrations should be correlated with each other by the conformational function of the polymer chain and should be discussed in different thermodynamic equations. On the basis of these concepts it has been proved that the Flory-Huggins entropy of mixing should be the result of the mixing “ideal gases of the gravity centers of macromolecules“. The general correlation between the free energy of mixing and the scattering function (structural factor) of polymer blends has been studied based on the general fluctuation theory. When the Flory-Huggins free energy of mixing is adopted, the de Gennes scattering function of a polymer blend can be derived.  相似文献   

13.
高镍三元正极材料由于高容量和高工作电压被认为是下一代锂离子电池有力的候选者,然而循环稳定性和热稳定性不佳限制了其广泛应用. 镍钴锰/铝三元浓度梯度正极材料的梯度设计可以在保证高容量的同时兼具优良的循环稳定性,因而在过去十年中得到了广泛研究. 本文综述了锂离子电池镍钴锰/铝三元浓度梯度材料最新的研究进展,论文首先总结了梯度材料的不同合成方法,并阐述了核壳浓度梯度材料和全浓度梯度材料的研究方向. 其次,介绍了浓度梯度材料的结构表征手段并揭示性能改善的原因. 最后讨论了目前该材料产业化的难点,并提出了可能的解决方案.  相似文献   

14.
利用链段浓度和链头浓度的概念,根据热力学涨落理论,给出了聚合物二元共混体系deGennes散射函数的一个普遍的热力学证明,指出了这个函数和Flory-Huggins共混自由能公式一样,也依赖于忽略构象涨落的假设.  相似文献   

15.
提出一种微混合器混合性能的评价方法.在样品盒中注入不同浓度罗丹明B溶液并用体视显微镜观察捕获图像,通过Image J软件读取图像灰度值,建立不同深度下溶液的浓度-灰度值函数关系,运用此关系式将T型微混合器3种不同深度(0.1、 0.2和0.4 mm,质量浓度0.05 %的罗丹明B溶液和去离子水作为配对流体)混合实验中捕获的图像中各像素点上的灰度值转换为浓度值,绘制浓度等高线图及浓度频数分布图,分析各自混合情况,最后引入浓度混合指数概念及计算公式,分析3种深度混合器内不同截面上的混合程度.此方法从定性和定量两方面分析了微尺度下混合腔深度对微混合的影响程度,具有一定的应用价值.  相似文献   

16.
Cellulose was dissolved rapidly in 9.5 wt.‐% NaOH/4.5 wt.‐% thiourea aqueous solution pre‐cooled to ?5 °C to prepare cellulose solution with different concentrations. The rheological properties of the cellulose solutions in wide concentration regimes from dilute (0.008 wt.‐%) to concentrated (4.0 wt.‐%) at 25 °C were investigated. On the basis of data from the steady‐shear flow test, the critical overlap (c*), the entanglement (ce) and the gel (cg) concentrations of the cellulose solution at 25 °C were determined, respectively, to be 0.10 wt.‐%, 0.53 wt.‐% and 2.50 wt.‐%, in accordance with the results of storage modulus (G′) versus c by dynamic test. Moreover, the Cox‐Merz deviation at relatively low concentrations was in good agreement with the micro‐gel particles in dilute regime. As the cellulose concentration increased, a homogeneous 3‐dimensional network formed in the cellulose solution in the concentrated regime, and further increasing of the concentration led to micro‐phase separation as determined by the time‐temperature superposition (tTS). So far, this complex cellulose solution has been successfully described by the concentration regime theory for the first time, and the relatively molecular morphologies in each regime have been determined, providing useful information for the applications of the cellulose solution systems.

  相似文献   


17.
多孔介质内的扩散有分子扩散和表面扩散两种。在吸附温度较高时 ,表面扩散可忽略 ,而在温度较低的吸附过程中 ,两种扩散均须考虑。Schneider和Smith[1 ] 曾用色谱法探讨了一种计算扩散系数的方法。他们认为等温吸附呈线性变化 ,引入了曲折系数 ,计算出分子扩散系数 (下称气相扩散系数 ) ,表面扩散系数 (下称吸附相扩散系数 )则由综合扩散系数减去分子扩散系数得到。文献 [2 ]则认为吸附过程非线性变化 ,服从Frundlich方程或Langmuir方程。从质量平衡方程得出相对吸附量方程 ,再求出各扩散系数。前一种方法将…  相似文献   

18.
《Analytical letters》2012,45(6):1035-1045
Abstract

A freeze concentration method was tested for its ability to concentrate uncharacterized organic carbon, measured by TOC analyzer, in tap water derived from a surface water reservoir in eastern Massachusetts. Freeze concentration was carried out in polypropylene bottles of 2 liter volume, stirred at either 140 rpm or 400 rpm, and placed in a freezer at either -15°C or -25°C. No effect of stirring speed or freezer temperature on the recovery efficiency was found except possibly at high (>10x) concentration factors. For theoretical concentration factors below approximately ten, measured TOC was reproducible but substantially less than the theoretical value (e.g., for a theoretical value of 10, the measured concentration factor was only 4.3. At higher concentration factors, the ratio of the actual to theoretical concentration decreased further and became variable from experiment to experiment. Lack of quantitative recovery of TOC indicates the likelihood that selective concentration of different components of this material occurred.  相似文献   

19.
The purpose of this work is to determine the values of critical premicelle concentration (CPMC), first critical micelle concentration (FCMC) and second critical micelle concentration (SCMC) of surfactants using a common spectrofluorophotometer by recording resonance Rayleigh scattering (RRS) signal without any probe. The plot of the RRS intensities at the maximum scattering wavelength (I(RRS)(max)) versus surfactant concentrations (c) was constructed to obtain the I(RRS)(max)-c curve. From the inflexions in I(RRS)(max)-c curve, the CPMC, FCMC and SCMC values of a surfactant can be obtained sensitively. The FCMC of some anionic, cationic and nonionic surfactants such as sodium dodecyl sulfate (SDS), sodium dodecyl benzene sulfonate (SDBS), cetyltrimethylammonium bromide (CTAB), cetylpyridinium chloride (CPC), Tween-20, and Tween-80 were determined by RRS method and the values are in good agreement with those obtained from conductivity and surface tension measurements and literature values. The CPMC and SCMC of SDS and CTAB were also determined by RRS method respectively and the values conform to literature values too. Furthermore, RRS method can also be used to determine the FCMC of an amphiphilic macromolecule-hemoglobin, whose structure resembles a surfactant. From the experimental results, it is concluded that RRS method can be applied to the simultaneous determination of the CPMC, FCMC and SCMC values in a sensitive, accurate and no probe way.  相似文献   

20.
多烷基苯磺酸钠水溶液的表面性质   总被引:8,自引:0,他引:8  
研究了多烷基苯磺酸钠的结构, 特别是侧链碳原子数的增加, 对其表面活性的影响, 并与其它烷基苯磺酸钠进行了比较. 结果表明, 随着苯环上侧链碳原子数的增加, 多烷基苯磺酸钠的临界胶束浓度(cmc)降低, 但侧链上CH2降低cmc的程度远小于主链上CH2的作用. 当侧链碳原子数增加时, 多烷基苯磺酸钠的饱和吸附量(Γmax)降低, 表现出与主链不同的变化规律. 从多烷基苯磺酸钠的结构解释了cmc和Γmax的变化规律.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号