顶空固相微萃取-气相色谱法测定海洋沉积物中的丁基锡化合物

三丁基锡化合物(TBT)广泛用于船舶的防污涂料,在海水中容易降解为二丁基锡化合物(DBT)和一丁基锡化合物(MBT),对敏感生物产生毒性~([1,2]).丁基锡一旦进入水环境后,可最终积累到海底底泥中,半衰期长达30年,对水生生物产生长期危害,因此,准确测定底泥中的丁基锡含量具有重要意义.固相微萃取集采样、浓缩、进样为一体,适合于复杂基体中的痕量物质的检测~([3]),本研究以东海海洋沉积物为检测对象,测定其中一丁基锡、二丁基锡和三丁基锡的含量.     

顶空固相微萃取技术用于海产品中丁基锡化合物的测定

采用顶空固相微萃取技术对生物样品中丁基锡化合物进行测定。用醋酸溶液浸提海产品中的丁基锡化合物,分析物经氢化衍生后用顶空固相微萃取方法富集,再以气相色谱分离,表面发射火焰光度检测器测定。整个过程简单快速,且无需消耗大量有毒的有机溶剂。方法的线性范围0～ 2000 ng/g (以锡的含量表示),相关系数 0.993?5 ～ 0.994?8 ,最低检测限(按S/N=3计算)3.4～52.4 ng/g (以锡的含量表示)。用该方法对贻贝标准参考物质CRM477进行测定,3种丁基锡化合物测定值的相对误差为0.     

气相色谱/质谱法测定水和沉积物中雄激素与孕激素

建立了气相色谱/质谱联用(GC-MS)技术同时测定水和沉积物中雄激素二氢睾酮、睾丸激素、雄烯二酮和孕激素孕酮的分析方法.分别确定了沉积物微波辅助萃取条件(萃取溶剂、萃取温度和萃取时间)和水样固相萃取条件(固相萃取柱、洗脱溶剂和水样pH值).结果表明:微波辅助萃取最优条件是乙酸乙酯为萃取溶剂,在120℃萃取15 min;以Oasis HLB为固相萃取柱,水样调节至pH4,采用乙酸乙酯为洗脱溶剂,固相萃取效果佳.以三甲基碘硅烷为催化剂,N-甲基-N-三甲基硅基三氟乙酰胺为衍生化试剂,将目标化合物分子结构上的羟基和酮基同步衍生化,并确定了衍生化过程的最佳反应温度为40℃,反应时间为20 min,满足了GC-MS分析该类物质的要求.水和沉积物中4种目标化合物检出限分别为0.1 ～ 0.5 ng/L和0.6 ～ 0.8ng/g,定量限分别为0.4 ～ 1.8 ng/L和1.9 ～2.6 ng/g,加标回收率分别为89.3％ ～ 101.4％和77.3％ ～92.1％,相对标准偏差(RSD)均小于9％.采用本方法对洱海水和沉积物样品进行了分析.     

加速溶剂萃取法提取海洋沉积物中正构烷烃的方法研究

采用加速溶剂萃取法(ASE)提取了海洋沉积物中的正构烷烃,并对ASE的萃取剂比例、萃取温度、静态萃取时间以及循环次数等实验条件进行优化。结果表明,当样品长碳链正构烷烃含量较高或需要检测长碳链正构烷烃含量时,可使用甲醇-二氯甲烷(1∶3)作为萃取剂;而甲醇-二氯甲烷(1∶9)适用于短碳链正构烷烃含量较高或需要检测短碳链正构烷烃含量的样品。加速溶剂萃取提取沉积物中正构烷烃的最佳条件为:萃取温度150℃,静态提取时间15 min,循环3次。在优化条件下,测定沉积物样品中正构烷烃的精密度除C15为20%外,其余为3%~14%,替代物回收率为84%~114%。相比于传统的索氏提取法,该方法的工作效率高、回收率高、精密度良好,适用于沉积物样品中正构烷烃的定量分析。     

顶空固相微萃取-气相色谱表面发射火焰光度检测法测定底泥中的丁基锡化合物

固相微萃取可用于多种样品基体中挥发、半挥发性有机化合物的测定。将固相微萃取技术应用于底泥样品中丁基锡化合物的富集和萃取,以气相色谱分离结合表面发射火焰光度检测器检测,方法灵敏、快速,一丁、二丁、三丁基锡的检测限可达16.9、1.58和0.17ng/g。     

沉积物中痕量多环芳烃湿法与干法提取的比较研究

以美国环保局(EPA)优先控制的16种多环芳烃(polycyclic aromatic hydrocarbons, PAHs)为研究对象,建立了湿法超声波辅助萃取技术提取沉积物中痕量PAHs的可靠方法,对萃取剂、萃取功率、萃取次数和萃取时间进行了优化.并与传统干法超声辅助萃取进行了比较,湿法超声波辅助萃取的PAHs回收率为57% ～125%,而干法超声波辅助萃取PAHs的回收率为48% ～113%,对相对分子质量小的PAHs如萘～芴的回收率,湿法明显高于干法.该文建立的湿法超声辅助萃取适用于沉积物和泥土中痕量PAHs的快速测定.     

高效液相色谱-电感耦合等离子质谱法分析海洋沉积物中有机锡的形态

建立了高效液相色谱-电感耦合等离子质谱(HPLC-ICP-MS)测定海洋沉积物中二丁基锡(DBT)、三丁基锡(TBT)、二苯基锡(DPhT)及三苯基锡(TPhT)的形态分析方法。通过改变流动相组分比例,使4种有机锡达到基线分离。比较不同提取方法对标准参考物质PACA-2中有机锡的提取效率。以V(乙腈)∶V(H2O)∶V(乙酸)=55∶33∶12(含5%三乙胺,pH 3.0)为提取剂时,超声提取效率最高(>91.5%),其加标回收率均大于96%。本方法对DBT,TBT,DPhT和TPhT的检出限分别达到0.7,0.75,0.45和0.4μg/kg。对浓度范围为0.5～100μg/kg有机锡混合标准溶液进行测定,4种有机锡回归系数均大于0.998。利用本方法对几种海洋沉积物样品和海产品中的有机锡进行测定,在部分沉积物样品中检测到了DBT和TBT,部分海产品中测到了少量TBT和TPhT。     

超声辅助-分散液相微萃取/高效液相色谱法测定沉积物中双酚A及其衍生物

建立了超声辅助-分散液相微萃取/高效液相色谱测定沉积物中双酚A,四溴双酚A,四溴双酚A双烯丙基醚,四溴双酚A双(2,3-二溴丙基)醚的方法。对萃取剂与分散剂的种类与用量、超声时间、盐效应及p H等萃取条件进行了优化。在优化的条件下,此方法的线性范围为0.1~100 mg/L,线性相关系数(r)为0.9996~0.9999。样品平均回收率为83%~91%,相对标准偏差为1.8%~4.9%。检出限(S/N=3)为0.01~0.15μg/L。方法可用于实际水库沉积物中双酚A及其衍生物的测定。     

气相色谱-质谱法测定纺织助剂中的有机锡

建立了纺织助剂中二丁基锡(dibutyltin, DBT)、三丁基锡(tributyltin, TBT)及三苯基锡(triphenyltin, TPhT)化合物的气相色谱-质谱联用(gas chromatography-mass spectrometry, GC-MS)检测方法。在乙酸-乙酸钠缓冲溶液(pH 4.0)中,用正己烷超声萃取(对疏水性样品)或振荡萃取(对亲水性样品)试样中的有机锡,然后以四乙基硼化钠的四氢呋喃溶液为衍生化试剂进行衍生化,用GC-MS测定,依据保留时间和选择离子定性,外标法定量。实验结果表明,在0.1～8.0 mg/L(对于DBT和TBT)或0.1～4.0 mg/L(对于TPhT)的范围内,有机锡化合物的浓度（以有机锡阳离子计）与其衍生物峰面积呈良好的线性关系,线性相关系数(r2)为0.9994～0.9998,检出限为0.003～0.005 mg/L; 4种聚氨酯类助剂基质中3种有机锡化合物的平均加标回收率为92.6%～108.0%,相对标准偏差为2.5%～10.2%。该方法的技术指标满足纺织助剂中有机锡化合物的测定要求。     

漩涡辅助-分散液液微萃取-高效液相色谱法测定沉积物中的多环芳烃

建立了漩涡辅助萃取(VAE)分散液液微萃取(DLLME)高效液相色普法(HPLC)测定水系沉积物中多环芳烃(PAHs)的方法。对萃取剂和分散剂的种类及体积、萃取时间、盐效应及pH值等参数进行了优化。在优化条件下,方法检出限为2.3～6.8 ng/g,线性范围为10～2100 ng/g,相关系数0.9986～0.9994,低、中、高3个浓度水平的平均加标回收率分别为85.2%±4.7%,85.0%±5.0%和85.0%±5.1%,平均相对标准偏差(RSD)分别为5.7%,6.1%和5.7%。采用本方法对实际沉积物样品中PAHs进行分析,所有沉积物样品中均检出PAHs,3组不同采样深度沉积物样品中PAHs平均含量分别为73.3,49 8和28.3 ng/g,平均加标回收率分别为84.8%±4.8%,83.1%±4.7%和84.6%±4.6%。     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.