Influence of water content on failure of phenolic composites in fire

This paper evaluates the structural performance of flame resistant phenolic matrix composites exposed to fire. Experimental fire tests were performed on a glass-phenolic composite under combined static loading and one-sided radiant heating. The reduction to the tension and compression failure strengths of the phenolic composite was measured in these tests for heat flux conditions ranging from 10 kW/m² (∼225 °C) to 75 kW/m² (∼700 °C). It was discovered that the failure strengths of the phenolic composite decreased rapidly in the event of fire, particularly under compressive loading when failure occurred more rapidly than under tensile loading. The phenolic composite, despite having high flame resistance, loses strength more rapidly and fails sooner than a more flammable vinyl ester composite. The study shows that greater flammability resistance does not necessarily result in better structural performance in fire. The poor structural performance of the phenolic composite was due to explosive delamination damage and cracking caused by vaporisation of water in the matrix phase. It is shown that removing water from phenolic composites by natural or artificial ageing reduces the incidence of delamination cracking and thereby improves the materials' structural performance in fire. It is concluded that phenolic composites do not provide good structural performance in fire, even though they have low flame and smoke properties. However, reducing the water content in the matrix phase below about 10% can greatly improve the structural performance of phenolic composites during fire.     

Study on ablative properties and mechanisms of hydrogenated nitrile butadiene rubber (HNBR) composites containing different fillers

The ablative properties of hydrogenated nitrile butadiene rubber (HNBR) composites filled with fumed silica, organically modified montmorillonite (OMMT), or expanded graphite (EG) were examined. The HNBR/OMMT composite has the lowest linear ablation rate and the highest mass ablation rate and does not tend to be carbonized. On the other hand, the HNBR/EG composite has the highest linear ablation rate and the lowest mass ablation rate, and is prone to carbonization. The ablative properties of the HNBR/silica composite are between those of HNBR/OMMT and HNBR/EG. From the viewpoint of thermal shielding capability, the HNBR/OMMT has the best ablation resistance. Thermogravimetric analysis (TGA) on different HNBR composites indicated that the filler type has no significant effect on the thermal stability of the composites. To understand the ablation mechanisms, the char layers of different HNBR composites after ablation experiments were characterized by scanning electron microscopy (SEM), energy disperse X-ray spectroscopy (EDS), and wide-angle X-ray diffraction (WAXD). The results showed that the porosity in the char layers of the HNBR/OMMT composite was the highest and the corresponding structure was the loosest of the three composites. The montmorillonite (MMT) dispersed in HNBR experienced phase transition, melting and vaporization when exposed to the flame with the temperature over 2000 °C. Fumed silica only melted at such situation. On the other hand, the EG kept their original crystalline structures after the ablation test. Based on these results, the effect of the filler type on the ablation mechanisms of the HNBR composites was discussed.     

Mechanical,acoustical and flammability properties of SBR and SBR-PU foam layered structure

In this work a layer structure from styrene butadiene rubber (SBR) composites and PU foam with improved flame retardancy property and high sound absorption coefficient at frequency range (200–500 Hz). Different types of flame retardants; iron (acrylic-co-acrylamide) as metal chelate (MC), magnesium hydroxide (MOH) and sodium tripolyphosphate (STP) were blended with SBR. The type and loading level of flame retardant had a great effect on filler dispersion and consequently on mechanical properties of SBR. MOH exhibited the best dispersion as indicated from scanning electron microscope (SEM), and SBR/MOH samples had almost the highest crosslink density (16.04*10⁻⁵ g⁻¹ mol) and the best mechanical properties where the tensile strength was improved by 32.7% at 40 phr MOH. Horizontal burning rate of SBR composites indicated that MC and MOH reduced the rate of burning of SBR at all loading levels. TGA data presented that the addition of flame retardants to SBR increased the maximum decomposition temperature in all composites. A double and triple layer structures of SBR composite and PU foam was designed. The effect of 2.5 cm air cavity on the sound absorption coefficient of SBR-PU foam layered structure was studied. The presence of air cavity behind the layered structure improved the sound absorption in the range of (200–500 Hz) better than the existence of it between the layers. The triple-layer structure gave higher sound absorption coefficient at lower frequencies than that obtained with the double-layer structure where it reached to ≥0.98 at 315 Hz.     

Preparation and properties of an efficient smoke suppressant and flame‐retardant agent for thermoplastic polyurethane

APP@ETA, as a new type of flame retardant, was prepared by chemically modifying ammonium polyphosphate (APP) with ethanolamine (ETA) and applied to thermoplastic polyurethane (TPU) in this study. Then, the smoke suppression properties and flame‐retardant effects of APP@ETA in TPU composites were evaluated using smoke density test, cone calorimeter test, etc. And, the thermal degradation properties of flame‐retardant TPU composites were investigated by thermogravimetric analysis/infrared spectrometry. The smoke density test results indicated that APP@ETA could obviously improve the luminous flux of TPU composites in the test with or without flame. The cone calorimeter test results showed that total smoke release, smoke production rate and smoke factor of the composites with APP@ETA were significantly decreased than those of the composites with APP. For example, when the loading of APP@ETA or APP was 12.5 wt%, the total smoke release of the sample with APP@ETA decreased to 3.5 m²/m² from 6.0 m²/m², which was much lower than that of the sample with APP, reduced by 41.7%. The thermogravimetric analysis results demonstrated that APP@ETA could decrease the initial decomposition temperature and improve the thermal stability at high temperature for TPU composites. Copyright © 2017 John Wiley & Sons, Ltd.     

Epoxy resin containing polyphenylsilsesquioxane: Preparation,morphology, and thermomechanical properties

Polyphenylsilsesquioxane (PPSQ) was incorporated into an epoxy resin to prepare organic–inorganic composites, and two strategies were adopted to afford composites with different morphologies. Phase separation induced by polymerization occurred in the physical blending system. However, nanostructured composites were obtained when a catalytic amount of aluminum triacetylacetonate was added to mediate the reaction between PPSQ and diglycidyl ether of bisphenol A (DGEBA). The intercomponent reaction significantly suppressed the phase separation on the micrometer scale. Organic–inorganic composites with different morphologies displayed quite different thermomechanical properties. Both differential scanning calorimetry and dynamic mechanical analysis showed that the nanostructured composites possessed higher glass‐transition temperatures than the phase‐separated composites with the same loading of PPSQ, although the intercomponent reaction between PPSQ and DGEBA reduced the crosslinking density of the epoxy matrix. This result was ascribed to the presence of nanosized PPSQ domains in the nanostructured composites, which acted as physical crosslinking sites and thus reinforced the epoxy networks. The nanoreinforcement of the PPSQ domains afforded the enhanced dynamic storage modulus for the nanostructured composites in comparison with the phase‐separated composites with a PPSQ concentration less than 15 wt %. In terms of thermogravimetric analysis, the organic–inorganic composites displayed improved thermal stability and flame retardancy. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1093–1105, 2006     

Synthesis of a novel polyphosphazene/triazine bi‐group flame retardant in situ doping nano zinc oxide and its application in poly (lactic acid) resin

A novel polyphosphazene/triazine bi‐group flame retardant in situ doping nano ZnO (A4‐d‐ZnO) was synthesized and applied in poly (lactic acid) (PLA). Fourier transform infrared (FTIR), solid state nuclear magnetic resonance (SSNMR), X‐ray photoelectron spectroscopy (XPS), scanning electron microscope (SEM), transmission electron microscope (TEM), and energy dispersive spectrometer (EDS) were used to confirm the chemical structure of A4‐d‐ZnO. The thermal stability and the flame‐retardant properties of the PLA composites were characterized by thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), limiting oxygen index (LOI), vertical burning test (UL‐94), and micro combustion calorimeter (MCC) test. The results of XPS showed that A4‐d‐ZnO has been synthesized, and the doping ratio of ZnO was 7.2% in flame‐retardant A4‐d‐ZnO. TGA results revealed that A4‐d‐ZnO had good char forming ability (40 wt% at 600°C). The results of LOI, vertical burning test, and MCC showed that PLA/5%A4‐d‐ZnO composite acquired a higher LOI value (24%), higher UL94 rating, and lower pk‐HRR (501 kW/m²) comparing with that of pure PLA. It indicated that a small amount of flame‐retardant A4‐d‐ZnO could achieve great flame‐retardant performance in PLA composites. The catalytic chain scission effect of A4‐d‐ZnO could make PLA composites drip with flame and go out during combustion, which was the reason for the good flame‐retardant property. Moreover, after the addition of A4‐d‐ZnO, the impaired mechanical properties of PLA composites are minimal enough.     

Synthesis and application of a dual functional P/N/S‐containing microsphere with enhanced flame retardancy and mechanical strength on EP resin

A phosphazene derivative flame retardant with a highly cross‐linked microsphere structure, named poly(cyclotriphosphazene‐c‐sulfonyldiphenol) (PCPS) microspheres, were synthesized by 1‐pot reaction and then applied on flame retarded epoxy (EP) resin. The microstructure and chemical composition of PCPS microspheres were characterized using scanning electron microscopy, transmission electron microscopy, and element mapping. The thermal stability of PCPS microspheres and PCPS/EP composites was explored through thermogravimetric analysis. Thermogravimetric data showed that the PCPS microspheres have excellent thermal stability, and the char yield is about 43% at the end of 800°C. The incorporation of PCPS microspheres significantly increased the char yield of PCPS/EP composites. The flammability was investigated by limited oxygen index tests and cone calorimeter. The limited oxygen index value of PCPS/EP composite was increased to 29.8 from 26.6 when 3 wt% of PCPS microspheres was added. Compared with neat EP, the flame retardancy was greatly improved. The peak heat release rate and smoke production rate of PCPS/EP composites were reduced by 45.0% and 43.6%, respectively. The mechanical properties including tensile strength and modulus were both improved due to the enhancement of PCPS microspheres. The PCPS microspheres act as a dual function for improving both the flame resistance and mechanical strength of PCPS/EP system.     

Mechanical and flame‐retardant properties and thermal decomposition of vinyl ester resin modified by different phenyl silsesquioxanes

The mechanical properties and fire resistance of vinyl ester resin (VER) composites containing cage‐shaped octaphenyl silsesquioxane (OPS), incompletely cage‐shaped phenyl silsesquioxane (PhT₇POSS), and ladder‐shaped phenyl silsesquioxane (PPSQ) were investigated. The POSS structure and dispersion have a great influence on the mechanical properties, thermal stability, and decomposition process of VER composites. The bending strength at break and modulus of the VER‐POSS composites were enhanced obviously, especially for VER‐PPSQ composite and VER‐OPS composite, respectively. In addition, PhT₇POSS‐based VER composites revealed the lower values of the peak heat release rate, total heat release, and total smoke release in cone calorimetry tests due to the formation of dense carbon/silica protective layers that acted as a barrier to heat and mass transfer. Moreover, the flame‐retardant mechanisms of condensed phase and gas phase were also investigated in detail. These results illustrate VERs modified by OPS, PhT₇POSS, and PPSQ are providing an applicable method to fabricate the composites with excellent flame‐retardant and mechanical properties.     

Microencapsulated Ammonium Polyphosphate with Polyurethane Shell: Application to Flame Retarded Polypropylene/Ethylene-propylene Diene Terpolymer Blends

Microencapsulated ammonium polyphosphate with polyurethane resin (PUMAPP) was prepared by in situ polymerization and characterized by X-ray photoelectron spectroscopy (XPS). The flame retardation of PUMAPP/dipentaerythritol(DPER) and ammonium polyphosphate (APP)/DPER flame retarded polypropylene (PP)/ethylene propylene diene rubber (EPDM) composites were studied using limiting oxygen index (LOI), UL-94 test and cone calorimeter. Results demonstrated that the flame retardancy of the PP/EPDM/PUMAPP/DPER composites was better than that of the PP/EPDM/APP/DPER composites at the same additive loading. Real time Fourier transform infrared (FTIR) and thermogravimetric analysis (TG) were used to study the thermal degradation and stability of the PP/EPDM/PUMAPP/DPER composite. The hydrolytic stability of the flame retarded PP/EPDM composites was studied. It was found that the microencapsulation of APP with the PU resin leaded to a decrease in the particle's water solubility. Moreover, the synergistic effect of vinyltrimethoxysilane (VTMS) on the PP/EPDM/PUMAPP/DPER composite was also investigated.     

Effect of unsaturated hydroxyl-fatty acid modified nano-CaCO3 on the morphological and rheological behavior of PP

A modified nano-calcium carbonate (R-CCR) was prepared by coating a layer of unsaturated hydroxylfatty acid on the surface of CCR powders using a solid state method; the latter were commercial nano-CaCO₃ modified with stearic acid. FTIR studies indicate that the modifier is combined on the surface of CaCO₃. PP/EPDM/nano-CaCO₃ ternary composites were prepared by a melt-mixing method. SEM and TEM were utilized to examine the morphology of the composites. The tensile fractured surface of PP/EPDM/R-CCR showed a fibroid morphology and large-scale yield deformation. The impact fractured surface showed that the amount of cavities in the PP/EPDM/R-CCR system was increased, however their size diminished obviously. R-CCR particles were dispersed uniformly in the PP matrix, and their compatibility was distinctly improved as compared to CCR when the amount of R-CCR was 15 h⁻¹. The tensile strength remained nearly constant (reduced from 27.6 MPa to 27.5 MPa), while the impact strength increased from 9.6 kJ/m² to 15.4 kJ/m² as CCR was replaced by R-CCR. Meanwhile, the bending strength and bending modulus also increased correspondingly. Furthermore, the impact strength of PP/EPDM/R-CCR was maintained at a high level (15.4 kJ/m²), which was more than the sum of that of PP/EPDM and PP/R-CCR (6.6 kJ/m² and 6.1 kJ/m² respectively). This indicates that the R-CCR and EPDM have a significant synergistic toughening effect on PP while maintaining the strength and modulus of virgin PP. Both the storage modulus G′ and loss modulus G″ of PP/EPDM and PP/EPDM/R-CCR composites increase with increasing frequency, but the values of G′ and G″ of the tertiary composite are relatively higher than those of the binary system. The loss factor and viscosity decrease with increasing frequency, but there is little difference between tertiary and binary composites. The apparent viscosity η of the tertiary system containing R-CCR is lower than that of the tertiary system containing CCR and virgin PP. The viscosity of the composites sig-nificantly decreases with increasing shear rate. The mea-sured mechanical properties of the composites indicate that replacing CCR with R-CCR for binary composites could simultaneously enhance the toughness and strength of PP. __________ Translated from Acta Polymerica Sinica, 2008, 4 (in Chinese)     

Synergistic effects of organo‐sepiolite and zinc borate on the fire retardancy of polypropylene

Polypropylene (PP)/sepiolite/zinc borate (BZn) composites were prepared by melt extrusion after pre‐modification of sepiolite with cetyltrimethylammonium bromide. The synergistic effects of organo‐sepiolite (OSEP) and BZn on the fire retardancy of PP were studied. X‐ray diffraction and transmission electron microscopy were used to characterize the morphology of the composite. Thermogravimetric analysis, cone calorimetric analysis, limiting oxygen index, and the UL‐94 protocol (Demaisheng technology Co. Ltd.,Shenzhen,China) were used to assess the thermal stability and fire retardancy of the composites. The fire retardancy of PP was greatly improved by introducing OSEP and BZn. The reduction in peak heat release rate for PP/BZn composites at 10% BZn loading is 62% compared with pristine PP, but increased to 78% for PP/10%BZn/10%OSEP composite. Other fire retardant parameters were also improved. The fire performance index of PP/10%BZn/10%OSEP composite was 0.045 sm²/kW compared with 0.014 sm²/kW of pristine PP. The average mass loss rate was 12.1 g/sec/m² for the composite with both additives compared with 30.1 g/sec/m² for pristine PP; the smoke production rate decreased by 37% from 0.117 m²/s of pristine PP to 0.074 m²/s of PP/OSEP/BZn. The char residue of composite increased from 0.6% in pristine PP to 12.19% in the composite. The limiting oxygen index increased from 17.1 in pristine PP to 20.8 in the composite: all the samples could obtain a UL‐94 horizontal burn rating. Copyright © 2013 John Wiley & Sons, Ltd.     

Effects of melamine polyphosphate and halloysite nanotubes on the flammability and thermal behavior of polyamide 6

Melamine polyphosphate (MPP) and halloysite nanotubes (HNT) were introduced to polyamide 6 (PA6) by melt blending in order to improve the fire resistance. PA6 composite containing 12% flame retardants with good spinnability was obtained. The flammability of PA6 composite was characterized by limiting oxygen index (LOI), UL‐94 vertical burning and cone calorimeter (CONE) tests. The results indicated that the LOI value could reach 24.0 vol.% and UL‐94 rating could achieve V2 level at the presence of 12% flame retardants. CONE data demonstrated that peak heat release rate was significantly reduced from 554 kW/m² of neat PA6 to 368 kW/m² of the sample containing flame retardants. Thermal analysis indicated that the thermal stability and char formation were improved by the presence of flame retardants. The morphology of residue char was characterized by scanning electron microscopy; and it suggested that a network‐structured protective char layer had been formed. The possible synergism between MPP/HNT and their flame retardant mechanism was also analyzed and discussed. Copyright © 2014 John Wiley & Sons, Ltd.     

Synergistic effects of cerium phosphate and intumescent flame retardant on EPDM/PP composites

An intumescent flame retardant system composed of ammonium polyphosphate (APP) and pentaerythritol (PER) was used for flame retarding ethylene–propylene–diene‐modified elastomer (EPDM)/polypropylene (PP) blends. Cerium phosphate (CeP) was synthesized and the effect on flame retardancy and thermal stability of EPDM/PP composites based on intumescent flame retardant (IFR) were studied by limiting oxygen index (LOI), UL‐94, and thermogravimetic analysis (TGA), respectively. Scanning electron microscopy (SEM) and Fourier transform infrared spectrometry (FTIR) were used to analyze the morphological structure and the component of the residue chars formed from the EPDM/PP composites, and the mechanical properties of the materials were also studied. The addition of CeP to the EPDM/PP/APP/PER composites gives better flame retardancy than that of EPDM/PP/APP/PER composites. TGA and RT‐FTIR studies indicated that an interaction occurs among APP, PER, and EPDM/PP. The incorporation of CeP improved the mechanical properties of the materials. Copyright © 2010 John Wiley & Sons, Ltd.     

Enhanced surface free energy of UHMWPE fibers and its interfacial adhesion behavior to PI resins

Mechanical properties of composites made up of ultra‐high‐molecular‐weight polyethylene (UHMWPE) fiber, polyimide (PI), and TiO₂ particles were investigated. The hybrid composite of 20 vol% of UHMWPE fiber with TiO₂ showed tensile strength greater than UHMWPE fiber/PI composite. A positive hybrid effect in tensile strength is obtained. It is observed that addition of small amount of TiO₂ to UHMWPE fiber/PI increased the tensile strength of the composite by 28%. With increase in TiO₂ loading to 1 to 3 vol%, the impact strength of the hybrid composite is increased from 55 KJ/m² to 69 KJ/m². This maximum value is more than one and a half times greater than the impact strength of neat UHMWPE fiber/PI composite.     

Synergistic fire safety improvement between oyster shell powder and ammonium polyphosphate in TPU composites

In this article, oyster shell powder (OSP) was used as fire safety agent with ammonium polyphosphate (APP) in thermoplastic polyurethane (TPU) composites. The synergistic fire safety improvement between OSP and APP was intensively investigated using limiting oxygen index (LOI), UL‐94, smoke density test (SDT), and cone calorimeter test (CCT). There is a good synergistic effect of reducing the fire hazards when OSP was used with APP in TPU. The peak heat release rate (pHRR) of the sample with 2.0‐wt% OSP and 8.0‐wt% APP decreased to 86.8 kW/m² from 175.7 kW/m² of the sample with only 10.0‐wt% APP. The SDT results showed that the luminous flux of sample OSP2/APP8 was up to 28.9% at the end of experiment with flame, which was much higher than that of pure TPU (1.5%). The thermal stability and thermal decomposition of TPU composites were characterized by thermogravimetric analysis/Fourier infrared spectrum analysis (TG‐IR). The result revealed the inert gasses (including CO₂ and water vapor) produced by the reaction between OSP and APP. A char formed on the surface of composites, hindered the flame spread, reduced the release of combustible gas, and restricted the precursor of smoke into combustion zone.     

Comparative study on the effect of partial replacement of silica or calcium carbonate by bentonite on the properties of EPDM composites

The effects of the partial replacement of silica or calcium carbonate (CaCO₃) by bentonite (Bt) on the curing behaviour, tensile and dynamic mechanical properties and morphological characteristics of ethylene propylene diene monomer (EPDM) composites were studied. EPDM/silica/Bt and EPDM/CaCO₃/Bt composites containing five different EPDM/filler/Bt loadings (i.e., 100/30/0, 100/25/5, 100/15/15, 100/5/25 and 100/0/30 parts per hundred rubber (phr)) were prepared using a laboratory scale two-roll mill. Results show that the optimum cure (t₉₀) and scorch (t_S2) time decreased, while the cure rate index (CRI) increased for both composites with increasing Bt loading. The tensile properties of EPDM/CaCO₃/Bt composites increased with the replacement of CaCO₃ by Bt from 0 to 30 phr of Bt. For EPDM/silica/Bt composites, the maximum tensile strength and E_b were obtained at a Bt loading of 15 phr, with enhanced tensile modulus on further increase of Bt loading. The dynamic mechanical studies revealed a strong rubber-filler interaction with increasing Bt loading in both composites, which is manifested by the lowering of tan δ at the glass transition temperature (Tg) for EPDM/CaCO₃/Bt composites and tan δ at 40 °C for EPDM/silica/Bt composites. Scanning electron microscopy (SEM) micrographs proved that incorporation of 15 phr Bt improves the dispersion of silica and enhances the interaction between silica and the EPDM matrix.     

Property correlations for composites based on ethylene propylene diene rubber reinforced with flax fibers

EPDM composites filled with short flax fibers were prepared by melt blending procedure. The effects of fiber loading on the mechanical, thermal and water uptake characteristics were studied. The physico-mechanical, morphological thermal properties and water absorption behavior were discussed using tensile testing, differential scanning calorimetry, thermogravimetrical analysis and scanning electron microscopy. Scanning electron microscopy revealed that the flax fibers were well dispersed in the polymer matrix. The tensile strength and hardness of the composites were found to be improved at higher fiber loading. The water absorption pattern of EPDM/fiber composites at room temperature follows a Fickian behavior for composites with 10, 15 and 20 phr flax fiber.     

Construction of crosslinking network structures by adding ZnO and ADR in intumescent flame retardant PLA composites

Different proportion of nano zinc oxide (nano ZnO) and chain extender (ADR) were combined with the intumescent flame retardant and then added into the PLA matrix. The thermal stability, flame retardant performance, and mechanical properties were studied. The gel content results showed that crosslinking structures were obtained after the addition of nano ZnO and ADR, which were generated by the catalytic chain scission effect of nano ZnO and chain extension effect of ADR. With addition of 1% nano ZnO and 1.6% ADR, the gel content of flame retardant PLA composite reached the highest value (14.2%). Meanwhile, the corresponding flame retardant PLA composite with 1% nano ZnO and 1.6% ADR, named FRPLA/ZnO/ADR-1, exhibited an overall improved properties including the flame retardant properties and mechanical performance, which passed the UL94 V-0 level with a limiting oxygen index value of 40.1%. Compared to FRPLA (flame retardant PLA without ZnO and ADR), the peak heat release rate and the total smoke production of FRPLA/ZnO/ADR-1were reduced by 60% and 67% respectively, and the final mass improved from 12% to 38%. In addition, the tensile strength and elongation at break of FRPLA/ZnO/ADR-1 increased by 25%, 14% compared with that of FRPLA. The impact strength was 15.1 kJ/m², which is similar to the pure PLA (15.6 kJ/m²). It indicated that the addition of nano ZnO and ADR could balance the flame retardant performance and the mechanical properties of the flame retardant PLA.     

Intumescent flame retardation and silane crosslinking of PP/EPDM elastomer

This study deals with the silane crosslinking and intumescent flame retardation of polypropylene/ethylene‐propylene‐diene copolymer (PP/EPDM) elastomers. The effect of silane crosslinking on the flame retardancy of the PP/EPDM composites containing melamine phosphate (MP) and dipentaerythritol (DPER) was studied by limiting oxygen index, UL 94 and cone calorimetry tests. The chemical composition of the silane crosslinked and flame retarded PP/EPDM composites treated at different temperatures was studied by X‐ray photoelectron spectroscopy and real time Fourier transform infrared (FTIR) spectrometry. Thermal decomposition and crystallization behavior of the PP/EPDM composites were investigated using thermogravimetric analysis and differential scanning calorimetry, respectively. Moreover, the mechanical properties of the composites were also studied. It is found that the flame retardancy, mechanical properties, and thermal decomposition behavior of the composites are influenced by silane grafting and crosslinking. Copyright © 2008 John Wiley & Sons, Ltd.     

Synergistic flame retardant effects of nano-kaolin and nano-HAO on LDPE/EPDM composites

A novel flame retardant system composed of nano-kaolin and nano-HAO (nano-sized hydroxyl aluminum oxalate) was used for flame retarding the low density polyethylene (LDPE)/ethylene propylene diene rubber (EPDM) blends. Results of fire testing showed that nano-kaolin and nano-HAO exhibited excellent synergistic effects on the flame retardancy of the LDPE/EPDM composites. When 12 wt% nano-kaolin took the place of 12 wt% nano-HAO in the composites, the LOI of the composites increased from 31.0% to 35.5% and the composites could meet the UL94V-0 standard. Through thermogravimetric and differential thermal analysis (TG-DTA) it was found that nano-HAO mainly affected the degradation of the experimental composites chemically. Meanwhile, results of scanning electronic microscope (SEM) and Fourier transformation infrared spectra (FTIR) of the composites on the char layer revealed that nano-kaolin mainly affected the transfer process physically by aggregating with nano-HAO and thus the synergistic effect on flame retardancy appeared.