Highly selective separation and detection of cyromazine from seawater using graphene oxide based molecularly imprinted solid‐phase extraction

A novel molecularly imprinted polymer based on graphene oxide was prepared as a solid‐phase extraction adsorbent for the selective adsorption and extraction of cyromazine from seawater samples. The obtained graphene oxide molecularly imprinted polymer and non‐imprinted polymer were nanoparticles and characterized by scanning electron microscopy. The imprinted polymer showed higher adsorption capacity and better selectivity than non‐imprinted polymer, and the maximum adsorption capacity was 14.5 mg/g. The optimal washing and elution solvents for molecularly imprinted solid phase extraction procedure were 2 mL of acetonitrile/water (80:20, v/v) and methanol/acetic acid (70:30, v/v), respectively. The recoveries of cyromazine in the spiked seawater samples were in the range of 90.3–104.1%, and the relative standard deviation was <5% (n = 3) under the optimal procedure and detection conditions. The limit of detection of the proposed method was 0.7 μg/L, and the limit of quantitation was 2.3 μg/L. Moreover, the imprinted polymer could keep high adsorption capacity for cyromazine after being reused six times at least. Finally, the synthesized graphene oxide molecularly imprinted polymer was successfully used as a satisfied sorbent for high selectivity separation and detection of cyromazine from seawater coupled with high‐performance liquid chromatography.     

Rapid determination of antiviral medication ribavirin in different feedstuffs using a novel magnetic molecularly imprinted polymer coupled with high‐performance liquid chromatography

A novel magnetic molecularly imprinted polymer adsorbing material was successfully synthesized to detect ribavirin in animal feedstuff. Molecularly imprinted polymer was prepared through surface polymerization by using ribavirin as template molecule, methyl methacrylate, and γ‐methacryloxypropyl trimethoxy silane functionalized magnetic mesoporous silica as bifunctional monomers, and ethylene diglycidyl ether as crosslinking agent. The prepared magnetic molecularly imprinted polymer was characterized by scanning electron microscopy and infrared spectroscopy. Static and dynamic adsorption experiments and selective adsorption analysis were performed to evaluate the adsorption and selectivity of magnetic molecularly imprinted polymer. Different experiments were conducted to optimize the magnetic solid‐phase extraction conditions. Under optimal experimental conditions, a magnetic molecularly imprinted solid‐phase extraction coupled with high‐performance liquid chromatography method was successfully developed for ribavirin detection. The established method achieved a satisfactory linear range of 0.20–50 mg/L (R² > 0.99) and a low detection limit (0.081 mg/kg). An average recovery of 92–105% with relative standard deviation of <6.5% was obtained upon the application of the developed method to detect ribavirin in real feedstuff samples. Thus, established method can be used for the rapid and simple separation and detection of added ribavirin in feedstuff.     

Magnetic molecularly imprinted polymer based on dynamically established metal-mediated binding sites for the determination of trace captopril in rat plasma

Therapeutic drug monitoring of captopril, which is a commonly used antihypertensive agent in clinical practice, is necessary. However, matrix effect-induced pretreatment is the bottleneck for determination. Metal-mediated molecularly imprinted polymers, an essential branch of molecularly imprinted polymers with better specificity and selectivity, have been used to separate/enrich analytes from complex matrices. In this work, Cu²⁺ was introduced to dynamically establish the binding sites of metal-mediated molecularly imprinted polymer towards captopril. All evidence demonstrated that the metal-mediated molecularly imprinted polymer based on Cu²⁺ coordination obtained a higher adsorption capacity (81.23 mg/g), faster adsorption rate (adsorption equilibrium within 50 min), and better selectivity (with the unrecognized analog). Subsequently, the Cu²⁺-mediated molecularly imprinted polymer was used as dispersive molecularly imprinted solid-phase extraction to successfully establish an analytical platform for the determination of trace captopril in rat plasma. The enrichment factor was up to 20, the detection limit was as low as 0.16 μg/ml, and the average recovery was in the range of 87.51%–98.28% with a relative standard deviation of less than 3.29%. This study provides a promising reference for the preparation of selective adsorbents to improve pretreatment.     

Preparation of magnetic molecularly imprinted polymer nanoparticles by surface imprinting by a sol–gel process for the selective and rapid removal of di‐(2‐ethylhexyl) phthalate from aqueous solution

Magnetic molecularly imprinted polymer nanoparticles for di‐(2‐ethylhexyl) phthalate were synthesized by surface imprinting technology with a sol–gel process and used for the selective and rapid adsorption and removal of di‐(2‐ethylhexyl) phthalate from aqueous solution. The prepared magnetic molecularly imprinted polymer nanoparticles were characterized using Fourier transform infrared spectroscopy, scanning electron microscopy, thermogravimetric analysis, and vibrating sample magnetometry. The adsorption of di‐(2‐ethylhexyl) phthalate onto the magnetic molecularly imprinted polymer was spontaneous and endothermic. The adsorption equilibrium was achieved within 1 h, the maximum adsorption capacity was 30.7 mg/g, and the adsorption process could be well described by Langmuir isotherm model and pseudo‐second‐order kinetic model. The magnetic molecularly imprinted polymer displayed a good adsorption selectivity for di‐(2‐ethylhexyl) phthalate with respect to dibutyl phthalate and di‐n‐octyl phthalate. The reusability of magnetic molecularly imprinted polymer was demonstrated for at least eight repeated cycles without significant loss in adsorption capacity. The adsorption efficiencies of the magnetic molecularly imprinted polymer toward di‐(2‐ethylhexyl) phthalate in real water samples were in the range of 98–100%. These results indicated that the prepared adsorbent could be used as an efficient and cost‐effective material for the removal of di‐(2‐ethylhexyl) phthalate from environmental water samples.     

Facile and versatile strategy to prepare magnetic molecularly imprinted particles based on the coassembly of magnetic nanoparticles and amphiphilic random copolymers

Magnetic molecularly imprinted polymer nanoparticles for bisphenol A were prepared by coassembling magnetic nanoparticles and amphiphilic random copolymers. Under optimized conditions, bisphenol A as template molecules, magnetic molecularly imprinted polymer particles with regular morphology, small size, good monodispersity, and high content of OA‐Fe₃O₄ were prepared by the coassembly method using P(MMA‐co‐MAA) with monomer ratio of 9:1. These magnetic molecularly imprinted polymer particles could be rapidly collected by an external magnet within 1 min. The saturated adsorption capacity of the magnetic molecularly imprinted polymer for bisphenol A was 201.5 mg/g, and the imprinting factor was 2.5. The separation factors for bisphenol A to β‐estradiol, estriol, and diethylstilbestrol was 3.1, 2.9, and 3.7, respectively. Unlike assembling amphiphilic copolymer in the selective solvent, the coassembly process was simple and rapid. Therefore, the present work provided a facile and versatile approach to construct magnetic molecularly imprinted polymer nanoparticles under mild conditions.     

Preparing molecularly imprinted membranes by phase inversion to separate kaempferol

Molecularly imprinted membranes (MIMs) were studied to separate special target molecule – kaempferol, an important active pharmaceutical ingredient. The kaempferol MIM were prepared by the liquid–solid phase inversion method. The effects of polyphenylene sulfone, LiCl, and ZnCl₂ on membrane performance were studied, a high Flux MIM was prepared, then the kaempferol molecularly imprinted polymer membrane, non‐molecularly imprinted membrane, and non‐molecularly imprinted polymer membrane were prepared to investigate adsorption capacity. From adsorption isotherm curve, the maximum equilibrium adsorption quantity was 890 µg/g, and it was MIM. The MIM and molecularly imprinted polymer membrane give high selectivity towards kaempferol; the non‐molecularly imprinted membrane and non‐molecularly imprinted polymer membrane showed low adsorption quantity and selectivity. The reuse experiment of the MIM indicated that it has good reuse property. All the results showed binding sites were important in the separation process of MIMs. Copyright © 2016 John Wiley & Sons, Ltd.     

Synthesis of a molecularly imprinted polymer on mSiO2@Fe3O4 for the selective adsorption of atrazine

Atrazine contamination of water is of considerable concern because of the potential hazard to human health. In this study, a magnetic molecularly imprinted polymer for atrazine was prepared by the surface‐imprinting technique using Fe₃O₄ as the core, mesoporous silica as the carrier, atrazine as the template, and itaconic acid as the functional monomer. The magnetic molecularly imprinted polymer was characterized by Fourier‐transform infrared spectroscopy, scanning electron microscopy, X‐ray diffraction, and vibration‐sample magnetometry. The binding properties of the magnetic molecularly imprinted polymer toward atrazine were investigated by adsorption isotherms, kinetics, and competitive adsorption. It was found that the adsorption equilibrium was achieved within 2 h, the maximum adsorption capacity of atrazine was 8.8 μmol/g, and the adsorption process could be well described by the Langmuir isotherm model and pseudo‐second‐order kinetic model. The magnetic molecularly imprinted polymer exhibited good adsorption selectivity for atrazine with respect to structural analogues, such as cyanazine, simetryne, and prometryn. The reusability of the magnetic molecularly imprinted polymer was demonstrated for at least five repeated cycles without a significant decrease in adsorption capacity. These results suggested that the magnetic molecularly imprinted polymer could be used as an efficient material for the selective adsorption and removal of atrazine from water samples.     

Preparation and application of magnetic molecularly imprinted polymers for the isolation of chelerythrine from Macleaya cordata

A novel type of magnetic molecularly imprinted polymer was prepared for the selective enrichment and isolation of chelerythrine from Macleaya cordata (Willd) R. Br. The magnetic molecularly imprinted polymers were prepared using functional Fe₃O₄@SiO₂ as a magnetic support, chelerythrine as template, methacrylic acid as functional monomer, and ethylene glycol dimethacrylate as cross‐linker. Density functional theory at the B3LYP/6‐31G (d, p) level with Gaussian 09 software was applied to calculate the interaction energies of chelerythrine, methacrylic acid and the complexes formed from chelerythrine and methacrylic acid in different ratios. The structural features and morphology of the synthesized polymers were characterized by using Fourier transform infrared spectroscopy, X‐ray diffraction, transmission electron microscopy, and vibration sample magnetometry. Adsorption experiments revealed that the magnetic molecularly imprinted polymers possessed rapid kinetics, high selectivity, and a higher binding capacity (7.96 mg/g) to chelerythrine than magnetic molecularly non‐imprinted polymers (2.36 mg/g). The adsorption process was in good agreement with the Langmuir adsorption isotherm and pseudo‐second‐order kinetics models. Furthermore, the magnetic molecularly imprinted polymers were successfully employed as adsorbents for the extraction and enrichment of chelerythrine from Macleaya cordata (Willd) R. Br. The results indicated that the magnetic molecularly imprinted polymers were suitable for the selective adsorption of chelerythrine from complex samples such as natural medical plants.     

Preparation and evaluation of temperature and magnetic dual‐responsive molecularly imprinted polymers for the specific enrichment of formononetin

Thermo‐responsive magnetic molecularly imprinted polymers were prepared by simple surface molecular imprinting polymerization for the selective adsorption and enrichment of formononetin from Trifolium pretense by temperature regulation. Using formononetin as a template, N‐isopropylacrylamide as the thermo‐responsive functional monomer, and methacrylic acid as an assisting functional monomer, the polymers were synthesized on the surface of the magnetic substrate. The results show that imprinted polymers attained controlled adsorption of formononetin in response to the temperature change, with large adsorption capacity (16.43 mg/g), fast kinetics (60 min) and good selectivity at 35°C compared with that at 25 and 45°C. The selectivity experiment indicated that the materials had excellent recognition ability for formononetin and the selectivity factors were between 1.32 and 2.98 towards genistein and daidzein. The excellent linearity was attained in the range of 5–100 μg/mL, with low detection limits and low quantitation limits of 0.017 and 0.063 μg/mL, respectively. Furthermore, the thermo‐responsive magnetic molecularly imprinted polymers were successfully utilized for enriching and purifying formononetin from Trifolium pretense. The analytical results indicate that the imprinted polymers are promising materials for selective identification and enrichment of formononetin in complicated herbal medicines by simple temperature‐responsive regulation.     

Selective enrichment and separation of phosphotyrosine peptides by thermosensitive molecularly imprinted polymers

Novel thermosensitive molecularly imprinted polymers were successfully prepared using the epitope imprinting approach in the presence of the mimic template phenylphosphonic acid, the functional monomer vinylphosphonic acid‐Ti⁴⁺, the temperature‐sensitive monomer N‐isopropylacrylamide and the crosslinker N,N′‐methylenebisacrylamide. The ratio of the template/thermosensitive monomers/crosslinker was optimized, and when the ratio was 2:2:1, the prepared thermosensitive molecularly imprinted polymers had the highest imprinting factor. The synthetic thermosensitive molecularly imprinted polymers were characterized by Fourier transform infrared spectroscopy to reveal the combination and elution processes of the template. Then, the adsorption capacity and thermosensitivity was measured. When the temperature was 28°C, the imprinting factor was the highest. The selectivity and adsorption capacity of the thermosensitive molecularly imprinted polymers for phosphotyrosine peptides from a mixture of three tailor‐made peptides were measured by high‐performance liquid chromatography. The results showed that the thermosensitive molecularly imprinted polymers have good selectivity for phosphotyrosine peptides. Finally, the imprinted hydrogels were applied to specifically adsorb phosphotyrosine peptides from a sample mixture containing phosphotyrosine and a tryptic digest of β‐casein, which demonstrated high selectivity. After four rebinding cycles, 78.9% adsorption efficiency was still retained.     

Molecularly imprinted polymer coating on metal‐organic frameworks for solid‐phase extraction of fluoroquinolones from water

In this work, a novel surface molecularly imprinted polymer with high adsorption capacity, high adsorption rate, and high selectivity for fluoroquinolones was prepared on the surface of UiO‐66‐NH₂, which is a kind of metal‐organic framework. The surface morphology and adsorption properties of this molecularly imprinted polymer were investigated. The maximum adsorption capacity was 99.19 mg/g, and adsorption equilibrium was achieved within 65 s. Combined with reversed‐phase high‐performance liquid chromatography, the molecularly imprinted polymer was used to selectively enrich, separate and analyze fluoroquinolones present in lake water. The results showed that the recoveries of the four fluoroquinolones were 92.6–100.5%, and the relative standard deviations were 2.9–6.4% (n = 3). The novel molecularly imprinted polymer is an excellent adsorbent and has broad application prospects in the enrichment and separation of trace analytes in complex samples.     

Theoretical design,preparation, and evaluation of Ginkgolide B molecularly imprinted polymers

Ginkgolide B is in great demand worldwide on account of its extensive and excellent pharmacological effects, however, it is difficult to separate and purify ginkgolide B. In this study, ginkgolide B molecularly imprinted polymers were prepared by combining software simulation and molecular imprinting technique, and its characterization and adsorption performed evaluation were performed to understand the adsorption behavior of the polymers. The adsorption equilibrium concentration of molecularly imprinted polymers was 0.70 mg/mL, and the adsorption equilibrium time was 4 h. Meanwhile, the adsorption isotherm of the polymers for ginkgolide B fitted well with the Langmuir model, and the adsorption kinetics was in line with the pseudo‐second‐order kinetics. In contrast, the adsorption capacity of molecularly imprinted polymers on ginkgolide B was higher than that of non‐molecular imprinted polymers, with better selectivity and better adsorption after repeated use for six times. The application experiments showed that molecular imprinted polymers have a good adsorption effect in low purity samples. Therefore, the polymers reported herein can be expected to apply in the adsorption and separation of ginkgolide B samples.     

Magnetic deep eutectic solvents molecularly imprinted polymers for the selective recognition and separation of protein

A novel and facile magnetic deep eutectic solvents (DES) molecularly imprinted polymers (MIPs) for the selective recognition and separation of Bovine hemoglobin (BHb) was prepared. The new-type DES was adopted as the functional monomer which would bring molecular imprinted technology to a new direction. The amounts of DES were optimized. The obtained magnetic DES-MIPs were characterized with fourier transform infrared spectrometry (FT-IR), thermogravimetric analysis (TGA), field emission scanning electron microscope (FESEM), dynamic light scattering (DLS), elemental analysis and vibrating sample magnetometer (VSM). The results suggested that the imprinted polymers were successfully formed and possessed a charming magnetism. The maximum adsorption capability (Q_max) and dissociation constant (K_L) were analyzed by Langmuir isotherms (R² = 0.9983) and the value were estimated to be 175.44 mg/g and 0.035 mg/mL for the imprinted particles. And the imprinted particles showed a high imprinting factor of 4.77. In addition, the magnetic DES-MIPs presented outstanding recognition specificity and selectivity so that it can be utilized to separate template protein from the mixture of proteins and real samples. Last but not least, the combination of deep eutectic solvents and molecular imprinted technology in this paper provides a new perspective for the recognition and separation of proteins.     

Synthesis of molecularly imprinted polymer nanoparticles for the fast and highly selective adsorption of sunset yellow

Novel molecularly imprinted polymer nanoparticles were synthesized by precipitation polymerization with sunset yellow as the template and [2‐(methacryloyloxy)ethyl] trimethylammonium chloride as the functional monomer. The molecularly imprinted polymer nanoparticles were characterized by Fourier transform infrared spectroscopy, scanning electron microscopy, transmission electron microscopy, and their specific surface area and thermal stability were measured. The molecularly imprinted polymer nanoparticles had a high adsorption capacity in wide pH range (pH 1–8) for sunset yellow. The adsorption equilibrium only needed 5 min, and the quantitative desorption was very fast (1 min) by using 10.0 mol/L HCl as the eluant. The maximum adsorption capacity of the molecularly imprinted polymer nanoparticles for sunset yellow was 144.6 mg/g. The adsorption isotherm and kinetic were well consistent with Langmuir adsorption model and pseudo‐second‐order kinetic model, respectively. The relative selectivity coefficients of the molecularly imprinted polymer nanoparticles for tartrazine and carmine were 9.766 and 12.64, respectively. The prepared molecularly imprinted polymer nanoparticles were repeatedly used and regenerated ten times without significant absorption capacity decrease.     

Preparation of magnetic molecularly imprinted polymer for dispersive solid‐phase extraction of valsartan and its determination by high‐performance liquid chromatography: Box‐Behnken design

In this work, core/shell magnetic molecularly imprinted polymer nanoparticles were synthesized for extraction and pre‐concentration of valsartan from different samples and then it was measured with high‐performance liquid chromatography. For preparation of molecularly imprinted polymer nanoparticles, Fe₃O₄ nanoparticles were coated with tetraethyl orthosilicate and then functionalized with 3‐(trimethoxysilyl) propyl methacrylate. In the next step, molecularly imprinted polymer nanoparticles were synthesized under reflux and distillation conditions via polymerization of methacrylic acid, valsartan (as a template), azobisisobutyronitrile and ethylene glycol dimethacrylate as cross linking. The properties of molecularly imprinted polymer nanoparticle were investigated by FTIR spectroscopy, field emission scanning electron microscopy, and X‐ray diffraction. Box‐Behnken design with the aid of desirability function was used for optimizing the effect of variables such as the amounts of molecularly imprinted polymer nanoparticles, time of sonication, pH, and volume of methanol on the extraction percentage of valsartan. According to the obtained results, the affecting variables extraction condition were set as 10 mg of adsorbent, 16 min for sonication, pH = 5.5 and 0.6 mL methanol. The obtained linear response (r² > 0.995) was in the range of 0.005–10 µg/mL with detection limit 0.0012 µg/mLand extraction recovery was in the range of 92–95% with standard deviation less than 6% (n = 3).     

Novel molecularly imprinted polymer prepared by nanoattapulgite as matrix for selective solid-phase extraction of diethylstilbestrol

Using nanoattapulgite as matrix, both diethylstilbestrol surface molecularly imprinted polymer and non-imprinted polymer were synthesized in this work. Compared with each other, the diethylstilbestrol surface molecularly imprinted polymer is superior to non-imprinted polymer in adsorption capacity, selectivity and mass transfer property. The maximum static adsorption capacities of diethylstilbestrol surface molecularly imprinted polymer, non-imprinted polymer and nanoattapulgite for diethylstilbestrol was 105.14, 78.54 and 28.50 mg g⁻¹, respectively. As the packing material of solid-phase extraction, the diethylstilbestrol surface molecularly imprinted polymer has been applied to concentrating diethylstilbestrol in pond water and fish samples. A corresponding analytical method to determine diethylstilbestrol has been developed. The limit of detection for diethylstilbestrol in pond water sample and fish samples were 3 μg L⁻¹ and 15 μg kg⁻¹.     

Selective extraction of fungicide carbendazim in fruits using β‐cyclodextrin based molecularly imprinted polymers

Considering the importance of developing a new analytical approach for pesticide residue detection for the sake of ensuring food safety, a β‐cyclodextrin based molecularly imprinted polymer was prepared for selective determination of carbendazim. The polymers consist of a porous and hollow structure demonstrating the selective abundant adsorption sites for carbendazim molecule. The selectivity and adsorption capacity of the imprinted polymers were analyzed with dispersive solid‐phase extraction and analyzed with high performance liquid chromatography coupled with ultraviolet. The results of imprinted polymers were higher than non‐imprinted polymers with the maximum adsorption capacity of 3.65 mg/g within 30 min of total adsorption time. The reusability of the imprinted polymers was determined to evaluate its effectiveness and stability, which proved that the polymers lost 10% efficiency within seven consecutive recycles. The developed method displayed good linearity over the concentration range of 0.05–2.0 mg/L. The recovery percentage of 81.33–97.23 with relative standard deviations of 1.49–4.66% was obtained from spiked apple, banana, orange, and peach samples with a limit of detection of 0.03 mg/L and a limit of quantification of 0.10 mg/L (signal to noise ratio = 3/10). The overall performance of the proposed method evident that this technique provided a desirable outcome and it can be used as a convenient approach, as it qualifies the analytical standards.     

A sensitive electrochemical sensor modified with multi‐walled carbon nanotubes doped molecularly imprinted silica nanospheres for detecting chlorpyrifos

A highly sensitive and convenient electrochemical sensor, based on surface molecularly imprinted polymers and multiwalled carbon nanotubes, was successfully developed to detect chlorpyrifos in real samples. In order to solve the problems like uneven shapes, poor size accessibility, and low imprinting capacity, the layer of the molecularly imprinted polymer was prepared on the surface of silica nanospheres. Moreover, the doping of multiwalled carbon nanotubes greatly improved the electrical properties of developed sensor. Under the optimal conductions, the electrochemical response of the sensor is linearly proportional to the concentration of chlorpyrifos in the range of 5.0 × 10^?12‐5.0 × 10^?8 mol/L with a low detection limit of 8.1 × 10^?13 mol/L. The prepared sensor exhibited multiple advantages such as low cost, simple preparation, convenient use, excellent selectivity, and good reproducibility. Finally, the prepared sensor was successfully used to detect chlorpyrifos in vegetable and fruit.     

Selective separation and determination of quercetin from red wine by molecularly imprinted nanoparticles coupled with HPLC and ultraviolet detection

In this study, a highly sensitive and selective sample pretreatment procedure using molecularly imprinted silica nanoparticles was developed for the extraction and determination of quercetin in red wine samples coupled with high‐performance liquid chromatography with ultraviolet detection. The imprinted silica nanoparticles were prepared in the presence of N‐acryoyl‐l ‐aspartic acid (functional monomer), quercetin (template), azobisisobutyronitrile (initiator) and methylene bisacrylamide (cross‐linker) and methanol/water (porogen) via surface‐initiated reversible addition‐fragmentation chain transfer polymerization. Surface characterization was performed and several imprinting parameters were investigated, and the results indicated that adsorption of quercetin on the imprinted silica nanoparticles followed a pseudo‐first‐order adsorption isotherm with a maximum adsorption capacity at 26.4 mg/g within 60 min. The imprinted silica nanoparticles also showed satisfactory selectivity towards quercetin as compared with its structural analogues. Moreover, the imprinted nanoparticles preserved their recognition ability even after five adsorption–desorption cycles. Meanwhile, the nanoparticles were successfully applied to selective extraction of quercetin from red wine with a high recovery (99.7–100.4%). The limit of detection was calculated to be 0.058 μg/mL with a correlation coefficient 0.9996 in the range of 0.2–50 μg/mL. As a result, the developed selective extraction method using molecular imprinting technology simplifies the sample pretreatment procedure before determination of quercetin in real samples.     

Preparation and characterization of molecularly imprinted polymers based on β‐cyclodextrin‐stabilized Pickering emulsion polymerization for selective recognition of erythromycin from river water and milk

Molecularly imprinted polymers were prepared via β‐cyclodextrin‐stabilized oil‐in‐water Pickering emulsion polymerization for selective recognition and adsorption of erythromycin. The synthesized molecularly imprinted polymers were spherical in shape, with diameters ranging from 20 to 40 µm. The molecularly imprinted polymers showed high adsorption capacity (87.08 mg/g) and adsorption isotherm data fitted well with Langmuir model. Adsorption kinetics study demonstrated that the molecularly imprinted polymers acted in a fast adsorption kinetic pattern and the adsorption features of molecularly imprinted polymers followed a pseudo‐first‐order model. Adsorption selectivity analysis revealed that molecularly imprinted polymers had a much better specificity for erythromycin than that for spiramycin or amoxicillin, and the relative selectivity coefficient values on the bases of spiramycin and amoxicillin were 3.97 and 3.86, respectively. The Molecularly imprinted polymers also showed a satisfactory reusability after four times of regeneration. In addition, molecularly imprinted polymers exhibited good adsorption capacities for erythromycin under complicated environment, that is, river water and milk. These results proved that the as‐prepared molecularly imprinted polymers is a potent absorbent for selective recognition of erythromycin, and therefore it may be a promising candidate for practical applications, such as wastewater treatment and detection of erythromycin residues in food.