Polymer electrolyte membranes by in situ polymerization of poly(ethylene carbonate‐co‐ethylene oxide) macromonomers in blends with poly(vinylidene fluoride‐co‐hexafluoropropylene)

Salt‐containing membranes based on polymethacrylates having poly(ethylene carbonate‐co‐ethylene oxide) side chains, as well as their blends with poly(vinylidene fluoride‐co‐hexafluoropropylene) (PVDF‐HFP), have been studied. Self‐supportive ion conductive membranes were prepared by casting films of methacrylate functional poly(ethylene carbonate‐co‐ethylene oxide) macromonomers containing lithium bis(trifluorosulfonyl)imide (LiTFSI) salt, followed by irradiation with UV‐light to polymerize the methacrylate units in situ. Homogenous electrolyte membranes based on the polymerized macromonomers showed a conductivity of 6.3 × 10^?6 S cm^?1 at 20 °C. The preparation of polymer blends, by the addition of PVDF‐HFP to the electrolytes, was found to greatly improve the mechanical properties. However, the addition led to an increase of the glass transition temperature (T_g) of the ion conductive phase by ～5 °C. The conductivity of the blend membranes was thus lower in relation to the corresponding homogeneous polymer electrolytes, and 2.5 × 10^?6 S cm^?1 was recorded for a membrane containing 10 wt % PVDF‐HFP at 20 °C. Increasing the salt concentration in the blend membranes was found to increase the T_g of the ion conductive component and decrease the propensity for the crystallization of the PVDF‐HFP component. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 79–90, 2007     

Characterization and evaluation of commercial poly (vinylidene fluoride)‐g‐sulfonatedPolystyrene as proton exchange membrane

The possibility of developing low‐cost commercial grafted and sulfonated Poly(vinylidene fluoride) (PVDF‐g‐PSSA) membranes as proton exchange membranes for fuel cell applications have been investigated. PVDF‐g‐PSSA membranes were systematically prepared and examined with the focus of understanding how the polymer microstructure (degree of grafting and sulfonation, ion‐exchange capacity, etc) affects their methanol permeability, water uptake, and proton conductivity. Fourier transform infrared spectroscopy was used to characterize the changes of the membrane's microstructure after grafting and sulfonation. The results showed that the PVDF‐g‐PSSA membranes exhibited good thermal stability and lower methanol permeability. The proton conductivity of PVDF‐g‐PSSA membranes was also measured by the electrochemical impedance spectroscopy method. It was found that the proton conductivity of PVDF‐g‐PSSA membranes depends on the degree of sulfonation. All the sulfonated membranes show high proton conductivity at 92°C, in the range of 27 to 235 mScm⁻¹, which is much higher than that of Nafion212 (102 mScm⁻¹ at 80°C). The results indicated that the PVDF‐g‐PSSA membranes are particularly promising membranes to be used as polymer electrolyte membranes due to their excellent stability, low methanol permeability, and high proton conductivity.     

Cross‐linked poly(aryl ether sulfone) membranes for direct methanol fuel cell applications

Partially sulfonated poly(aryl ether sulfone) (PESS) was synthesized and methacrylated via reaction with glycidyl methacrylate (PESSGMA) and cross‐linked via radical polymerization with styrene and vinyl‐phosphonic acid (VPA). The chemical structures of the synthesized pre‐polymers were characterized via FTIR and ¹H NMR spectroscopic methods and molecular weight was determined via GPC. Membranes of these polymers were prepared via solution casting method. The crosslinking of the PESS polymer reduced IEC, proton conductivity, swelling in water, and methanol permeability of the membranes while increasing the modulus and the glass transition temperature. However, the introduction of the VPA comonomer increased the proton conductivity while maintaining excellent resistance to methanol cross‐over, which was significantly higher as compared with both PESS and the commercial Nafion membranes. Membranes of PESSGMA copolymers incorporating VPA, exhibited proton conductivity values at 60 °C in the range of 16–32 mS cm⁻¹ and methanol permeability values in the range of 6.52 × 10⁻⁹ – 1.92 × 10⁻⁸ cm² s⁻¹. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 558–575     

Synthesis and properties of novel sulfonated polyimides containing binaphthyl groups as proton‐exchange membranes for fuel cells

A novel sulfonated diamine monomer, 2,2′‐bis(p‐aminophenoxy)‐1,1′‐binaphthyl‐6,6′‐disulfonic acid (BNDADS), was synthesized. A series of sulfonated polyimide copolymers containing 30–80 mol % BNDADS as a hydrophilic component were prepared. The copolymers showed excellent solubility and good film‐forming capability. Atomic force microscopy phase images clearly showed hydrophilic/hydrophobic microphase separation. The relationship between the proton conductivity and degree of sulfonation was examined. The sulfonated polyimide copolymer with 60 mol % BNDADS showed higher proton conductivity (0.0945–0.161 S/cm) at 20–80 °C in liquid water. The membranes exhibited methanol permeability from 9 × 10^?8 to 5 × 10^?7 cm²/s at 20 °C, which was much lower than that of Nafion (2 × 10^?6cm²/s). The copolymers were thermally stable up to 300 °C. The sulfonated polyimide copolymers with 30–60 mol % BNDADS showed reasonable mechanical strength; for example, the maximum tensile strength at break of the sulfonated polyimide copolymer with 40 mol % BNDADS was 80.6 MPa under high moisture conditions. The optimum concentration of BNDADS was found to be 60 mol % from the viewpoint of proton conductivity, methanol permeability, and membrane stability. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 222–231, 2007     

Novel sulphonated poly (vinyl chloride)/poly (2-acrylamido-2-methylpropane sulphonic acid) blends-based polyelectrolyte membranes for direct methanol fuel cells

Proton-conducting and methanol barrier properties of the proton exchange membrane (PEM), as well as the high cost of direct methanol fuel cell (DMFC) components, are the key determinants of the performance and commercialization of DMFCs. Therefore, this study aimed to develop cost- and performance-effective membranes based on sulphonated poly (vinyl chloride) (SPVC)/poly (2-acrylamido-2-methyl-1-propane sulphonic acid) (PAMPS) blends. Such membranes have been simply prepared by blending SPVC and PAMPS solutions, followed by solvent evaporation via casting. Interaction of SPVC with PAMPS was confirmed by different characterization techniques such as Fourier Transform Infra-red (FTIR) and Raman scattering spectroscopy in which the two characteristic absorption bands of sulfonic groups appeared at 1093 and 1219 cm⁻¹ additionally, strong peaks at around 1656 cm⁻¹ attributed to vibration of amide groups of PAMPS portion in the polymer blend. Furthermore, the interaction of SPVC with PAMPS improves the thermal properties along with ion exchange capacity in turn decreasing the methanol permeability through the membrane in comparison with the SPVC membrane. The IEC of PVC and Nafion 117 membranes were 1.25, 0.91 meq/g; respectively. And the maximum water uptake of PVC and Nafion 117 membranes were 75 and 65.44%; respectively. Methanol permeability value of 7.7 × 10⁻⁷ cm²/s which was noticeably lower than the corresponding value recorded for Nafion® (3.39 × 10⁻⁶ cm²/s). Therefore, these fabricated membranes can be considered a low-cost efficient candidate for use in DMFC, especially for its capability to resolve the methanol cross-over issue.     

Effect of the initial matrix material on the structure of radiation‐grafted ion‐exchange membranes: Wide‐angle and small‐angle X‐ray scattering studies

Seven different fluoropolymer films were used as matrix materials for radiation‐grafted ion‐exchange membranes. The crystallinity and preferred orientation of these membranes were studied with wide‐angle X‐ray scattering, and the lamellar structure of the membranes was examined with small‐angle X‐ray scattering. The crystallinity of poly(vinylidene fluoride) (PVDF)‐based matrix materials varied between 57 and 40%, and the crystallinity of the sulfonated samples varied between 34 and 23%. The lamellar periods of PVDF‐based matrix materials were about 115 Å, and the lamellar periods of poly(ethylene‐alt‐tetrafluoroethylene) and poly(tetrafluoroethylene‐co‐hexafluoropropylene) were 250 and 212 Å, respectively. When the samples were grafted, the lamellar periods increased. Correlation function analysis showed very clearly that the long‐range order decreased because of grafting and sulfonation processes. For those samples that showed good proton conductivity, the lamellar period also increased because of sulfonation. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1539–1555, 2002     

Proton conducting membranes based on poly(vinyl chloride) graft copolymer electrolytes

The direct preparation of proton conducting poly(vinyl chloride) (PVC) graft copolymer electrolyte membranes using atom transfer radical polymerization (ATRP) is demonstrated. Here, direct initiation of the secondary chlorines of PVC facilitates grafting of a sulfonated monomer. A series of proton conducting graft copolymer electrolyte membranes, i.e. poly(vinyl chloride)‐g‐poly(styrene sulfonic acid) (PVC‐g‐PSSA) were prepared by ATRP using direct initiation of the secondary chlorines of PVC. The successful syntheses of graft copolymers were confirmed by ¹H‐NMR and FT‐IR spectroscopy. The images of transmission electron microscopy (TEM) presented the well‐defined microphase‐separated structure of the graft copolymer electrolyte membranes. All the properties of ion exchange capacity (IEC), water uptake, and proton conductivity for the membranes continuously increased with increasing PSSA contents. The characterization of the membranes by thermal gravimetric analysis (TGA) also demonstrated their high thermal stability up to 200°C. The membranes were further crosslinked using UV irradiation after converting chlorine atoms to azide groups, as revealed by FT‐IR spectroscopy. After crosslinking, water uptake significantly decreased from 207% to 84% and the tensile strength increased from 45.2 to 71.5 MPa with a marginal change of proton conductivity from 0.093 to 0.083 S cm^?1, which indicates that the crosslinked PVC‐g‐PSSA membranes are promising candidates for proton conducting materials for fuel cell applications. Copyright © 2008 John Wiley & Sons, Ltd.     

Preparation of novel sulfonated block copolyimides for proton conductivity membranes

In this article novel sulfonated block copolyimides with various diamine compositions and block chain lengths were synthesized by chemical imidization using a two‐pot procedure. The proton conductivities of the block copolyimide membranes were measured as functions of the relative humidity and temperature using four‐point‐probe electrochemical impedance spectroscopy. The proton conductivity of the membranes strongly depended on the block chain lengths and increased with an increase in the block chain lengths. The proton conductivity of NTDA‐BDSA‐b‐6FAP (112/48) as the block copolyimide membrane was approximately 0.35 S cm⁻¹ which indicated a higher value when compared to that determined for Nafion®. Copyright © 2005 John Wiley & Sons, Ltd.     

Synthesis and Characterization of Sulfonated Polyimides Containing Trifluoromethyl Groups as Proton Exchange Membranes

A novel sulfonated diamine, 4,4′‐bis(4‐amino‐3‐trifluoromethylphenoxy) biphenyl 3,3′‐disulfonic acid (F‐BAPBDS), was successfully synthesized by nucleophilic aromatic substitution of 4,4′‐dihydroxybiphenyl with 2‐chloro‐5‐nitrobenzotrifluoride, followed by reduction and sulfonation. A series of sulfonated polyimides of high molecular weight (SPI‐x, x represents the molar percentage of the sulfonated monomer) were prepared by copolymerization of 1,4,5,8‐naphathlenetetracarboxylic dianhydride (NTDA) with F‐BAPBDS and nonsulfonated diamine. Flexible and tough membranes of high mechanical strength were obtained by solution casting and the electrolyte properties of the polymers were intensively investigated. The copolymer membranes exhibited excellent oxidative stability due to the introducing of the CF₃ groups. The SPI membranes displayed desirable proton conductivity (0.52×10⁻¹–0.97×10⁻¹ S·cm⁻¹) and low methanol permeability (less than 2.8×10⁻⁷ cm²·s⁻¹). The highest proton conductivity (1.89×10⁻¹ S·cm⁻¹) was obtained for the SPI‐90 membrane at 80°C, with an IEC of 2.12 mequiv/g. This value is higher than that of Nafion 117 (1.7×10⁻¹ S·cm⁻¹). Furthermore, the hydrolytic stability of the obtained SPIs is better than the BDSA and ODADS based SPIs due to the hydrophobic CF₃ groups which protect the imide ring from being attacked by water molecules, in spite of its strong electron‐withdrawing behaviors.     

Chitosan‐based composite membranes containing chitosan‐coated carbon nanotubes for polymer electrolyte membranes

Considering the poor dispersion and inert ionic conduction ability of carbon nanotubes (CNTs), functionalization of CNTs is a critical issue for their application in polymer electrolyte membranes. Herein, CNTs were functionalized by the polyelectrolyte, chitosan (CS), via a facile noncovalent surface‐deposition method. The obtained CS‐coated CNTs (CS@CNTs) were then incorporated into the CS matrix and fabricated composite membranes. The CS coating can enhance the compatibility between CNTs and the matrix, thus ensuring the homogenous dispersion of CS@CNTs and effectively improved the mechanical properties of the composites. Moreover, the CS coating can make CS@CNTs act as an additional proton‐conducting pathway through the membranes. The CS/CS@CNTs‐1 composite shows the highest proton conductivity of 3.46 × 10⁻² S cm⁻¹ at 80°C, which is about 1.5‐fold of the conductivity of pure CS membrane. Consequently, the single cell equipped with CS/CS@CNTs‐1 membrane exhibits a peak power density of 47.5 mW cm⁻², which is higher than that of pure CS (36.1 mW cm⁻²).     

Synthesis of sulfonated poly(imidoaryl ether sulfone) membranes for polymer electrolyte membrane fuel cells

New sulfonated poly(imidoaryl ether sulfone) copolymers derived from sulfonated 4,4′‐dichlorodiphenyl sulfone, 4,4′‐dichlorodiphenyl sulfone, and imidoaryl biphenol were evaluated as polymer electrolyte membranes for direct methanol fuel cells. The sulfonated membranes were characterized with Fourier transform infrared spectroscopy, thermogravimetric analysis, and proton nuclear magnetic resonance spectra. The state of water in the membranes was measured with differential scanning calorimetry, and the existence of free water and bound water was discussed in terms of the sulfonation level. The 10 wt % weight loss temperatures of these copolymers were above 470 °C, indicating excellent thermooxidative stability to meet the severe criteria of harsh fuel‐cell conditions. The proton conductivities of the membranes ranged from 3.8 × 10^?2 to 5 × 10^?2 S/cm at 90 °C, depending on the degree of sulfonation. The sulfonated membranes maintained the original proton conductivity even after a boiling water test, and this indicated the excellent hydrolytic stability of the membranes. The methanol permeabilities ranged from 1.65 × 10^?8 to 5.14 × 10^?8 cm²/s and were lower than those of other conventional sulfonated ionomer membranes, particularly commercial perfluorinated sulfonated ionomer (Nafion). The properties of proton and methanol transport were discussed with respect to the state of water in the membranes. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5620–5631, 2005     

Preparation and ion conductivities of the plasticized polymer electrolytes based on the poly(acrylonitrile‐ co‐lithium methacrylate)

The polymer electrolytes composed of poly(acrylonitrile‐co‐lithium methacrylate) [P(AN‐co‐LiMA)], ethylene carbonate (EC), and LiClO₄ salts have been prepared. The ion groups in the P(AN‐co‐LiMA) were found to prevent EC from crystallization through their ion–dipole interactions with the polar groups in the EC. This suppression of the EC crystallization could lead to the enhancement of the ion conductivity at subambient temperature. The polymer electrolytes based on the PAN ionomer with 4 mol % ion content exhibited ion conductivities of 2.4 × 10⁻⁴ S/cm at −10°C and 1.9 × 10⁻³ S/cm at 25°C by simply using EC as a plasticizer. In the polymer electrolytes based on the PAN ionomer, ion motions seemed to be coupled with the segmental motions of the polymer chain due to the presence of the ion–dipole interaction between the ion groups in the ionomer and the polar groups in the EC, while the ion transport in the PAN‐based polymer electrolytes was similar to that of the liquid electrolytes. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 247–252, 1999     

P (VDF‐co‐CTFE)‐g‐P2VP amphiphilic graft copolymers: Synthesis,structure, and permeation properties

A series of amphiphilic graft copolymers of poly (vinylidene fluoride‐co‐chlorotrifluoroethylene)‐g‐poly(2‐vinyl pyridine), P (VDF‐co‐CTFE)‐g‐P2VP, with different degrees of P2VP grafting (from 26.3 to 45.6 wt%) was synthesized via one‐pot atom transfer radical polymerization (ATRP). The amphiphilic properties of P (VDF‐co‐CTFE)‐g‐P2VP graft copolymers allowed itself to self‐assemble into nanoscale structures. P (VDF‐co‐CTFE)‐g‐P2VP graft copolymers were introduced into neat P (VDF‐co‐CTFE) as additives to form blending membranes. When two different solvents, N‐methyl‐2‐pyrrolidone (NMP) and dimethylformamide (DMF), were used, specific organized crystalline structures were observed only in the NMP systems. P (VDF‐co‐CTFE)‐g‐P2VP played a pivotal role in controlling the morphology and pore structure of membranes. The water flux of the membranes increased from 57.2 to 310.1 L m^?2 h^?1 bar^?1 with an increase in the PVDF‐co‐CTFE‐g‐P2VP loading (from 0 to 30 wt%) due to increased porosity and hydrophilicity. The flux recovery ratio (FRR) increased from 67.03% to 87.18%, and the irreversible fouling (R_ir) decreased from 32.97% to 12.82%. Moreover, the pure gas permeance of the membranes with respect to N₂ was as high as 6.2 × 10⁴ GPU (1 GPU = 10^–6 cm³[STP]/[s cm² cmHg]), indicating their possible use as a porous polymer support for gas separation applications.     

Synthesis of poly(arylene ether sulfone)‐block‐sulfonated polybutadiene: the selective post‐sulfonation of block copolymers as proton exchange membranes

A series of poly(arylene ether sulfone)‐block‐sulfonated polybutadiene (PAES‐b‐sPB) with different ion exchange capacities (IECs) were synthesized and evaluated as proton exchange membranes (PEMs) for possible applications in fuel cells. These sulfonated block copolymers were synthesized via condensation reaction between modified PAES and PB prepolymers, followed by selective post‐sulfonation of PB blocks using acetyl sulfate as the sulfonating reagent. The sulfonic groups were only attached onto PB blocks due to the high reactivity of double bonds to acetyl sulfate. The success of synthesis and selective post‐sulfonation were all confirmed by the Fourier transform infrared (FT‐IR) and nuclear magnetic resonance (NMR) spectra. PAES‐b‐sPB had good film‐forming ability and thermal stability. Mechanical properties of membranes varied with the sulfonation. The presence of sulfonic groups increased the tensile strength and Young's modulus but decreased the elongation at break. Transmission electron microscopy (TEM) images showed large ionic aggregates in membranes. Phase separation as well as the interconnected sulfonate groups which only localized on flexible PB blocks led to these ionic domains. The proton conductivity increased with the increasing IEC and temperature. With relatively low IEC, most membranes still exhibited sufficient proton conductivity. The above results indicated this strategy could be a prospective choice to prepare novel PEMs. Copyright © 2010 John Wiley & Sons, Ltd.     

Highly proton conducting proton‐exchange membranes based on fluorinated poly(arylene ether ketone)s with octasulfonated segments

A new bisphenol monomer containing a pair of electron‐rich tetra‐arylmethane units was designed and synthesized. Based on this monomer, along with commercial 4,4′‐(hexafluoroisopropylidene)diphenol A and 4,4′‐difluorobenzophenone, a series of novel poly(arylene ether ketone)s containing octasulfonated segments of varying molar percentage (x) (6F‐SPAEK‐x) were successfully synthesized by polycondensation reactions, followed by sulfonation. Tough, flexible, and transparent membranes, exhibiting excellent thermal stabilities and mechanical properties were obtained by casting. 6F‐SPAEK‐x samples exhibited appropriate water uptake and swelling ratios at moderate ion exchange capacities (IECs) and excellent proton conductivities. The highest proton conductivity (215 mS cm⁻¹) is observed for hydrated 6F‐SPAEK‐15 (IEC = 1.68 meq g⁻¹) at 100 °C, which is more than 1.5 times that of Nafion 117. Furthermore, the 6F‐SPAEK‐10 membrane exhibited comparable proton conductivity (102 mS cm⁻¹) to that of Nafion 117 at 80 °C, with a relatively low IEC value (1.26 meq g⁻¹). Even under 30% relative humidity, the 6F‐SPAEK‐20 membrane (2.06 meq g⁻¹) showed adequate conductivity (2.1 mS cm⁻¹) compared with Nafion 117 (3.4 mS cm⁻¹). The excellent comprehensive properties of these membranes are attributed to well‐defined nanophase‐separated structures promoted by strong polarity differences between highly ionized and fluorinated hydrophobic segments. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 25–37     

Styrene grafted ethylene chlorotrifluoroethylene (ECTFE‐g‐PSSA) protonic membranes: Preparation,characterization, and transport mechanism

The main goal of the present work is the development of partially fluorinated, low‐cost proton exchange membranes. The styrene grafted onto commercial ethylene chlorotrifluoroethylene (ECTFE) membranes using solution grafting technique, and after that the membranes were sulfonated. Diluting styrene on ECTFE with a solvent mixture of methanol plus methylene chloride (1:1) was highly effective in promoting the grafting reaction as indicated by the increase in the degree of grafting (DG) to 21.3% compared to other solvents. The DG in ECTFE membranes increased with an increase in the monomer concentration up to 60% and then declined. Fourier transform infrared spectroscopic analysis confirmed grafting and sulfonation onto ECTFE films. The maximum value of proton conductivity for ECTFE‐g‐PSSA film with DG = 21.3% was observed to be 141 mS cm⁻¹, which is also higher than those of Nafion 212 membrane. Furthermore, the activation energy of ECTFE‐g‐PSSA membranes was obtained ranging from 8.27 to 9.726 kJ mol⁻¹. So both proton transport mechanisms (hopping and vehicle) have been commonly accepted. The mobility of the charge carriers calculated from proton conductivity data has robust dependence on the grafting yield and temperature. Moreover, the tensile strength and elongation at break ratio decreases with the increase in DG. The water and methanol uptakes increase up to 0.97% and 30%, respectively, for the highest DG value. Finally, the ECTFE‐g‐PSSA has lower cost and higher conductivity they could be better used instead of Nafion in direct methanol fuel cells.     

Synthesis and properties of new fluorinated polymers bearing pendant imidazole groups for fuel cell membranes operating over a broad relative humidity range

New alternating copolymers comprising a chlorotrifluorinated backbone and imidazole‐terminated pendant ethylene oxide groups have been prepared with a view to their use as a component of proton‐conducting membranes in polymer electrolyte fuel cells. A vinyl ether containing an imidazole (Imi) function protected by a benzyl group (BVI) was first synthesized in a three‐step reaction. It was then copolymerized in solution with chlorotrifluoroethylene (CTFE) by conventional radical copolymerization leading to alternating poly(BVI‐alt‐CTFE) copolymers in good yields. Deprotection of the benzyl group under hydrogen produced a chlorotrifluorinated poly(Imi‐alt‐CTFE) copolymer. The polymer was subsequently used to form blend membranes with sulfonated poly(ether ether ketone) (sPEEK). The conductivity of blend membranes of poly (Imi‐alt‐CTFE) with sPEEK lies in the range of 4–10 mS cm^?1 at 40–70 °C and, for blend membranes rich in poly(Imi‐alt‐CTFE), is little dependent on relative humidity between 30 and 100%. It is surmised that the polymer and membrane composition favor microstructural phase separation into chlorotrifluorinated polymer backbone domains and regions in which imidazole groups are clustered. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 223–231, 2010     

Pore‐filling electrolyte membranes based on microporous polyethylene matrices activated with plasma and sulfonated hydrogenated styrene butadiene block copolymer. Synthesis,microstructural and electrical characterization

In this research a series of pore‐filling electrolyte membranes were prepared, based on a sulfonated and hydrogenated styrene/butadiene block copolymer (SHSBS) and plasma‐treated microporous polyethylene (PE) membranes. The pore‐filling electrolyte membranes were characterized by means of scanning electronic microscopy (SEM), infrared spectroscopy (FTIR‐ATR), and dynamic mechanical analysis (DMA). In addition, the water uptake and methanol/water uptake capacities of these membranes were determined using several methanol in water solutions, as well as the permeability coefficients, for both water and methanol, using a 2 M methanol in water solution and pure methanol. Finally, electrical behavior was recorded by means of electrochemical impedance spectroscopy (EIS) and the four probe technique (FPT). The SEM images recorded show good coating of the pore‐filling electrolyte membranes on the plasma‐treated PE matrices, and DMA shows the proper relaxations of the two components: PE and SHSBS. Furthermore, the methanol/water absorption capacity was observed to diminish with plasma treatment of the matrix. Methanol permeability of the pore‐filling electrolyte membranes is notably lower than that of the Nafion® membrane, ion conductivity moving in the order of 10⁻² S cm⁻¹. Both of these characteristics qualify the experimental membranes as candidates to be applied as proton exchangers in fuel cells (FCs). © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1684–1695, 2008     

Proton‐conductive membranes based on blends of polyimides

We prepared novel proton‐conductivity membranes based on blends of sulfonated polyimides. The blend membranes were prepared from a sulfonated homopolyimide and a sulfonated copolyimide with a solvent‐casting method. The proton conductivities of the blend membranes were measured as functions of the temperature with four‐point‐probe electrochemical impedance spectroscopy. The conductivity of the membranes strongly depended on the sulfonated homopolyimide content and increased with an increase in the content. The proton conductivity of all the blended membranes indicated a higher value than that determined in Nafion at 80 °C, and this may mean that the proton transfer in the blend membranes is responsible for the ionic channels induced by the hydrophobic and hydrophilic domains. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1325–1332, 2007     

Synthesis and Characterization of New Phosphorus Containing Sulfonated Polytriazoles for Proton Exchange Membrane Application

Sulfonated polytriazoles have drawn a great attention as high performance polymers and their good film forming ability. In the present study, a phosphorus containing new diazide monomer namely, bis-[4-(4′-aminophenoxy)phenyl]phenylphosphine was synthesized and accordingly, a series of phosphorus containing sulfonated polytriazoles (PTPBSH-XX) was synthesized by reacting equimolar amount of this diazide monomer (PAZ) in combination with another sulfonated diazide monomer (DSAZ) and a terminal bis-alkyne (BPALK) by the Cu (I) catalyzed azide–alkyne click polymerization. The polymers were characterized by nuclear magnetic resonance (¹H, ¹³C, ³¹P NMR) and Fourier transform infrared spectroscopic techniques. The sulfonic acid content of the copolymers also determined from the different integral values obtained from the ¹H NMR signals. The small-angle X-ray scattering results unfolded the well-separated dispersion of the hydrophilic and hydrophobic domains of the polymers. As a whole, the copolymer membranes displayed sufficient thermal, mechanical, and oxidative stabilities high with high proton conductivity and low water uptake that are essential for proton exchange membrane applications. The copolymers exhibited oxidative stability in the range of 15–24 h and had proton conductivity values were found as high as 38–110 mS cm⁻¹ at 80 °C in completely hydrated condition. Among the all copolytriazoles, PTPBSH-90 (BPALK:DSAZ:PAZ = 100:90:10) having IEC_W = 2.44 mequiv g⁻¹, showed proton conductivity as high as 119 mS cm⁻¹ at 90 °C with an activation energy of 10.40 kJ mol⁻¹ for the proton conduction. © 2020 Wiley Periodicals, Inc. J. Polym. Sci. 2020 , 58, 263–279