Shape‐memory effect in hyperbranched poly(ethyleneimine)‐modified epoxy thermosets

A series of shape‐memory epoxy thermosets were synthesized by crosslinking diglycidyl ether of bisphenol A with mixtures of commercially available hyperbranched poly(ethyleneimine) and polyetheramine. Thermal, mechanical and shape‐memory properties were studied and the effect on them of the content and structure of the hyperbranched polymer was discussed. Measurements showed that the glass transition temperature can be tailored from 60 °C to 117 °C depending on the hyperbranched polymer content, and all formulations showed an appropriate glassy/rubbery storage modulus ratio. Shape‐memory programming was carried out at TgE′ given the excellent mechanical properties of the materials, with maximum stress and failure strain up to 15 MPa and 60%, respectively. The resulting shape‐memory behavior was excellent, with maximum shape recovery and shape fixity of 98% as well as a fast shape‐recovery rate of 22%/min. The results show that hyperbranched poly(ethyleneimine) as a crosslinking agent can be used to enhance mechanical and shape‐memory properties with different effects depending on the crosslinking density. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 924–933     

Shape memory induced structural evolution of high performance copolyimides

In this work, two kinds of high temperature shape memory copolyimides were prepared and the shape memory cycles induced structural evolution of macromolecular chains was investigated in detail. The glass transition temperature (T_g) of poly(benzoxazole‐co‐imide) (PI1) and poly(benzimidazole‐co‐imide) (PI2) are 280 °C and 355 °C, respectively. The results show that PI1 could keep stable macromolecular chain structure under shape memory cycles and exhibit outstanding shape memory performance (R_f > 98%, R_r > 97%) under different stretch condition. Whereas, shape memory cycles induced orientation with more ordered macromolecular chains packing is formed for PI2 after several thermal mechanical cycles, which strongly affect physical crosslinking points, thermal mechanical properties as well as shape memory behaviors. The study on macroscopic property and microscopic structure evolution will promote a better understanding of the shape memory effect of polyimides and accelerate development of high performance polyimides for shape memory applications. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 3858–3867     

A review of shape memory polymers bearing reversible binding groups

Shape memory polymers (SMP) can be deformed to a stable, temporary shape and recovered to their original shape by applying a stimulus. These networks rely on the presence of two types of net points to establish their permanent and temporary shapes. Classical strategies to stabilize temporary shapes rely on cooling below T_g/T_m where macromolecules become pinned in a stressed state. Recovery of the SMP usually involves heating to above the transition temperature where the permanent shape is remembered. Employing reversible binding groups (RBGs) in SMPs has emerged as an alternative strategy for stabilizing temporary shapes or imparting recyclability of the permanent shape. The use of dynamic chemistry often engenders additional functionality such as intrinsic self-healing characteristics or alternative shape recovery triggering strategies. SMPs bearing both supramolecular and covalent RBGs will be reviewed with an emphasis on hydrogen bonding, ionic interactions, metal–ligand coordination, and dynamic covalent exchange and addition reactions. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 1340–1364     

Organic–inorganic polyurethanes with double decker silsesquioxanes in the main chains: Morphologies,surface hydrophobicity,and shape memory properties

In this contribution, we reported an investigation of the morphologies, surface hydrophobicity, and shape memory properties of the organic–inorganic polyurethanes with double decker silsesquioxane (DDSQ) in the main chains. It was found that the organic–inorganic polyurethanes were microphase‐separated and that the POSS cages in the main chains were self‐organized into the spherical microdomains with the size of 10–50 nm in diameter. The introduction of POSS cages into the main chains resulted in the enhancement of glass transition temperatures (T_g's). In the meantime, the surface dewettability of the materials was significantly enhanced. X‐ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM) indicates the improvement of the surface hydrophobicity resulted from the enrichment of POSS at the surfaces of the polyurethanes. The mechanical analyses, such as dynamic mechanical analysis (DMA) and creep‐recovery analysis (CRA), indicate that the POSS microdomains dispersed in the polyurethanes behaved as the physical crosslinking sites and promoted the formation of the crosslinked networks. Owing to the introduction of DDSQ into the main chains, the organic–inorganic polyurethanes significantly displayed shape memory properties, in marked contrast to the unmodified and linear polyurethane. The shape memory behavior has been addressed on the formation of the strong physically crosslinked networks in the organic–inorganic polyurethanes. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 893–906     

Influence of matrix glass transition temperature on the memory effect of polymer‐dispersed liquid crystals

In this article, macroinitiators with different glass transition temperature (T_g) were synthesized by reversible additional‐fragmental chain transfer polymerization, and used to prepare polymer‐dispersed liquid crystals (PDLCs) with methyl acrylate. The memory effect of these PDLCs was investigated. The results showed that remarkable memory effect exhibit only in PDLCs with high and low T_g block chain. The possible mechanism responsible for the behavior is sketched. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 729–732, 2010     

Novel interpenetrating networks with shape‐memory properties

Novel polyesterurethane/poly(ethylene glycol) dimethacrylate (PEGDMA) interpenetrating networks (IPNs) with good shape‐memory properties were synthesized using solvent casting method. The star‐shaped oligo[(rac‐lactide)‐co‐glycolide] was coupled with isophorone diisocyanate to form a polyesterurethane network (PULG), and PEGDMA was photopolymerized to form another polyetheracrylate network. IPNs were transparent and gel content exceeded 92%. The values of strain fixity rate and strain recovery rate were above 93%. PULG and PEGDMA networks in IPNs were amorphous and did not show any characteristic diffraction peaks in X‐ray diffraction spectra. Only one glass transition temperature (T_g) of the IPNs between T_g of PEGDMA and PULG was observed, which was proportional to PEGDMA content. PULG and PEGDMA networks were miscible when PEGDMA content was below 50 wt %. The hydrophilicity, transition temperatures, and mechanical properties of IPNs could be conveniently adjusted through variation of network compositions to match the promising potential clinical or medical applications. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 768–775, 2007     

Thiol–norbornene materials: Approaches to develop high Tg thiol–ene polymers

The ability to prepare high T_g low shrinkage thiol–ene materials is attractive for applications such as coatings and dental restoratives. However, thiol and nonacrylated vinyl materials typically consist of a flexible backbone, limiting the utility of these polymers. Hence, it is of importance to synthesize and investigate thiol and vinyl materials of varying backbone chemistry and stiffness. Here, we investigate the effect of backbone chemistry and functionality of norbornene resins on polymerization kinetics and glass transition temperature (T_g) for several thiol–norbornene materials. Results indicate that T_gs as high as 94 °C are achievable in thiol–norbornene resins of appropriately controlled chemistry. Furthermore, both the backbone chemistry and the norbornene moiety are important factors in the development of high T_g materials. In particular, as much as a 70 °C increase in T_g was observed in a norbornene–thiol specimen when compared with a sample prepared using allyl ether monomer of analogous backbone chemistry. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5686–5696, 2007     

Thermo‐/moisture‐responsive shape‐memory effect of poly(2‐ethyl‐2‐oxazoline) networks

In this work, poly(2‐ethyl‐2‐oxazoline) (PEtOx) is crosslinked to realize a moisture‐ and thermo‐responsive shape‐memory polymer. The obtained PEtOx networks exhibit excellent shape‐memory properties with storable strains of up to 650% and recovery values of 100% over at least 10 shape‐memory cycles. The trigger temperature (T_trig) of 68 °C of a PEtOx network at a relative humidity (RH) of 0% decreases with increasing moisture and equals room temperature at an RH of 40%. Thus, programmed PEtOx networks trigger sensitively on a certain temperature/moisture combination and, further, can be programmed as well as triggered at room temperature exclusively by varying humidity. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 1053–1061     

Uniaxial tensile tests and dynamic mechanical analysis of satin weave reinforced epoxy shape memory polymer composite

The utilization of epoxy shape memory polymer composite (SMPCs) as engineering materials for deployable structures has attracted considerable attention in recent decades due to high strength and satisfactory stiffness in comparison with shape memory polymers (SMPs). Knowledge of static and dynamic mechanical properties is essential for analyzing structural behavior and recovery properties, especially for new epoxy SMPCs. In this paper, a new weave reinforced epoxy shape memory polymer composite was prepared with satin weave technique and resin transfer molding technique. Uniaxial tensile tests and dynamic mechanical analysis were carried out to obtain basic mechanical properties and glass transition temperatures, respectively.The tensile strength and breaking elongation of warp specimens were comparable with those of weft specimens. The increment of elastic modulus and hysteresis loop areas became smaller with loading cycles, meaning that cyclic tests could obtain approximate stable mechanical properties. For dynamic mechanical properties, glass transition temperature (T_g) obtained from storage modulus curves was lower than that determined from tan delta curves and T_gs in the warp and weft directions were similar (29.4 °C vs 29.7 °C). Moreover, the storage modulus in response to T_g was two orders of magnitude less than that with respect to low temperature, which demonstrated the easy processibility of epoxy SMPCs near glass transition temperature. In general, this study could provide useful observations and basic mechanical properties of new epoxy SMPCs.     

Recovery stress and work output in hyperbranched poly(ethyleneimine)‐modified shape‐memory epoxy polymers

In this study a series of hyperbranched modified shape‐memory polymers were subjected to constrained shape recoveries in order to determine their potential use as thermomechanical actuators. Materials were synthesized from a diglycidyl ether of bisphenol A as base epoxy and a polyetheramine and a commercial hyperbranched poly(ethyleneimine) as crosslinker agents. Hyperbranched polymers within the structure of the shape‐memory epoxy polymers led to a more heterogeneous network that can substantially modify mechanical properties. Thermomechanical and mechanical properties were analyzed and discussed in terms of the content of hyperbranched polymer. Shape‐memory effect was analyzed under fully and partially constrained conditions. When shape recovery was carried out with fixed strain a recovery stress was obtained whereas when it was carried out with a constraining stress the material performs mechanical work. Tensile tests at Tg^E′ showed excellent values of stress and strain at break (up to 15 MPa and almost 60%, respectively). Constrained recovery performances revealed rapid recovery stress generation and unusually high recovery stresses (up to 7 MPa) and extremely high work densities (up to 750 kJ/m³). The network structure of shape‐memory polymers was found to be a key factor for actuator‐like applications. Results confirm that hyperbranched modified‐epoxy shape memory polymers are good candidates for actuator‐like shape‐memory applications. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 1002–1013     

Actuation design for high‐performance shape memory polyurethanes

A series of shape memory polyurethanes were synthesized from poly(tetramethylene glycol), 4,4‐methylene diphenyl diisocyanate, and 1,3‐butanediol. The prepolymers with different molecular weights (M_c) were capped with 2‐hydroxyl ethylacrylate or 3‐aminopropyltriethoxysilane (APTES) and crosslinked by UV curing or a sol–gel reaction. Variations of the crosslinker functionality (f), subchain density (N), and hard segment content (HSC) produced systematic variations of the glass transition temperature (6–45 °C), accompanied by changes in the mechanical, dynamic mechanical and shape memory properties. More than 95% of shape fixity and 98% of shape recovery up to the fourth cycles were obtained with APTES crosslinked 3000M_c with 30% of HSC. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2013 , 51, 1473–1479     

A new technique for measuring retrograde vitrification in polymer–gas systems and for making ultramicrocellular foams from the retrograde phase

A stepwise temperature‐ and pressure‐scanning thermal analysis method was developed to measure glass‐transition temperature T_g in the two‐phase polymer–gas systems as a function of gas pressure p, and was used to confirm recent theoretical predictions that certain polymer–gas systems exhibit retrograde vitrification, that is, they undergo rubber‐to‐glass transition on heating. A complete T_g‐p profile delineating the glass–rubber phase envelope was established for the PMMA‐CO₂ system. The retrograde vitrification behavior observed, where at certain gas pressures the polymer exists in the rubbery state at low and high temperatures and in the glassy state at intermediate temperatures, was similar to that reported previously based on the creep‐compliance measurements. The existence of the rubbery state at low temperatures was used to generate foams by saturating the polymer with CO₂ at 34 atm and at temperatures in the range −0.2 to 24 °C followed by foaming at temperatures in the range 24 to 90 °C. Foams with very fine cell structure never reported before could be prepared by this technique. For example, PMMA foams with average cell size of 0.35 μm and cell density of 4.4 × 10¹³ cells/g were prepared by processing the low temperature rubbery phase. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 716–725, 2000     

Effects of annealing above Tg on the physical aging of quenched PLLA studied by modulated temperature FTIR

The effect of the annealing few degrees above the glass transition temperature (T_da = 62 °C) on the physical aging (T_pa = 51 °C) of amorphous quenched poly(l ‐lactide) is investigated by an implementation of variable temperature Fourier transform infrared (FTIR). By using a temperature program composed of a linear heating ramp superimposed to a temperature modulation (modulated temperature FTIR), the reversing and nonreversing intensity variation of selected bands, related to high‐energy gg and low‐energy gt conformers, is investigated. It is observed that the annealing above T _g changes irreversibly the conformation distribution of the liquid polymer. The glasses obtained from annealed and nonannealed liquids behave differently, evolving in the physical aging toward their own liquid state and retaining the memory of their original condition before the vitrification. The recovery through T _g of the relaxation occurred in the physical aging depends not only from aging conditions but also by the thermal history of the sample above the T_g. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 174–181     

Carbon nanotube–polyurethane shape memory nanocomposites with low trigger temperature

Ester-based polyurethane (PU) with low glass transition temperature was used to develop shape memory nanocomposites with low trigger temperature. Pristine carbon nanotubes (CNTs) and oxidized CNTs (ox-CNTs) were introduced by melt mixing to improve the mechanical and shape memory properties of the PU matrix. The dispersion of CNTs on the mechanical properties and shape memory behaviors of the nanocomposites were also investigated. The results show that better dispersion of ox-CNTs contributes to more stiffness effect below glass transition temperature (T_g) while lower storage modulus (E′) above T_g. The nanocomposites exhibit high shape fixity and recovery ratio above 98%. The ox-CNT/PU nanocomposite shows higher shape recovery ratio for the first cycle, faster recovery due to better dispersion of CNTs and have potential applications for controlling tags or proof marks in the area of frozen food. The trigger temperature can be tailored by controlling the T_g of the PU matrix or the content of the nanofillers.     

Morphology of polylactic acid crystallized during annealing after uniaxial deformation

Uniaxial deformation of amorphous L -polylactic acid films was performed at two different temperatures at which thermal degradation was minimal, 70 °C or T_g + 10 and 90 °C or T_g + 30. Samples were annealed postdeformation for long times (either 15 or 45 min) to approach equilibrium conditions. Samples deformed and annealed at 70 °C showed low crystallinity and poor crystalline order or crystal size, as determined by wide-angle X-ray diffraction. At 90 °C, high crystallinity and order parameters were observed. In addition, once the oriented chains had crystallized at this temperature, nonoriented chains also underwent crystallization, and a small fraction of nonordered crystal phase was therefore observed after long annealing times. These observations are explained on the basis of different morphologies in samples drawn at the two temperatures. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2013     

The linear rheological responses of wedge‐type polymers

The linear rheological responses of a series of specially designed wedge‐type polymers synthesized by the polymerization of large molecular weight monomers have been measured. These wedge polymers contained large side groups which contained three flexible branch chains per polymer chain unit. The master curves for these polymers were obtained by time temperature superposition of dynamic data at different temperatures from the terminal flow regime to well below the glass transition temperature, T_g. While these polymers maintained a behavior similar to that of linear polymers, the influence of the large side group structure lead to low entanglement densities and extremely low rubbery plateau modulus values, being near to 13 kPa. The viscosity molecular weight dependence was also somewhat higher than that normally observed for linear polymers, tending toward a power law near to 4.2 rather than the typical 3.4 found in entangled linear chains. The glassy modulus of these branched polymers is also found to be extremely low, being less than 100 MPa at T_g ?60 °C. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 899–906     

Effect of composition on the width of the calorimetric glass transition in polymer–solvent and solvent–solvent mixtures

The calorimetric glass‐transition temperature (T_g) and transition width were measured over the full composition range for solvent–solvent mixtures of o‐terphenyl with tricresyl phosphate and with dibutyl phthalate and for polymer–solvent mixtures of polystyrene with three dialkyl phthalates. T_g shifted smoothly to higher temperatures with the addition of the component with the higher T_g for both sets of solvent–solvent mixtures. The superposition of the differential scanning calorimetry traces showed almost no composition dependence for the width of the transition region. In contrast, the composition dependence of T_g in polymer–solvent mixtures was different at high and low polymer concentrations, and two distinct T_g's were observed at intermediate compositions. These results were interpreted in terms of the local length scale and associated local composition variations affecting T_g. The possible implications of these results for the dynamics of miscible polymer blends were examined. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1155–1163, 2004     

Energy storage and strain‐recovery processes in highly deformed semicrystalline poly(butylene terephthalate)

Nonelastic deformation of semicrystalline poly(butylene terephtalate) (PBT) was investigated by calorimetric measurements and strain‐recovery tests. Differential scanning calorimetry on PBT specimens deformed both below and above their glass‐transition temperature (T_g ≈ 50 °C) showed the presence of a broad exothermal peak whose area represents the energy released for the nonelastic strain recovery. This energy became more and more pronounced as the strain level increased, and it decreased as the deformation temperature increased, even if a significant contribution was detected on specimens deformed at temperatures much higher than T_g. For two temperature conditions (21 and 100 °C), strain‐recovery master curves were built showing the following two distinct deformation components: one recoverable with time and another one irreversible, this latter one arising from relatively low levels of strain. The recoverable component can be erased by heating the material at temperatures much higher than its T_g, close to the onset of the melting process. On the other hand, the irreversible strain component does not recover even if the material is brought close to the onset of the crystals melting. The shift factor for the strain‐recovery master curves was compared with the shift factor for the construction of the dynamic storage modulus master curve obtained in the linear viscoelastic regime (small strain). © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 40: 236–243, 2002     

Synthesis and characterization of novel renewable polyesters based on 2,5‐furandicarboxylic acid and 2,3‐butanediol

Novel polyesters from 2,5‐furandicarboxylic acid or 2,5‐dimethyl‐furandicarboxylate and 2,3‐butanediol have been synthesized via bulk polycondensation catalyzed by titanium (IV) n‐butoxide, tin (IV) ethylhexanoate, or zirconium (IV) butoxide. The polymers were analyzed by size exclusion chromatography, nuclear magnetic resonance spectroscopy, Fourier transform infrared spectroscopy (FTIR), matrix‐assisted laser ionization‐desorption time‐of‐flight mass spectrometry, electrospray ionization time‐of‐flight mass spectrometry, electrospray ionization quadruple time‐of‐flight mass spectroscopy, thermogravimetric analysis, and differential scanning calorimetry. Fully bio‐based polyesters with number average molecular weights ranging from 2 to 7 kg/mol were obtained which can be suitable for coating applications. The analysis of their thermal properties proved that these polyesters are thermally stable up to 270–300 °C, whereas their glass transition temperature (T_g) values were found between 70 and 110 °C. Furthermore, a material was prepared with a molecular weight of 13 kg/mol, with a T_g of 113 °C. This high T_g would make this material possibly suitable for hot‐fill applications. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Parameters affecting transition temperatures of poly(lactic acid‐co‐polydiols) copolymer‐based polyester urethanes and their shape memory behavior

A series of polyester urethanes (PEUs) comprising poly(lactic acid‐co‐polydiol) copolymers as a soft segment, 4,4′‐diphenylmethane diisocyanate (MDI) and 1,4‐butanediol (BDO) as a hard segment were systematically synthesized. Soft segments, which were block copolymers of L ‐lactide (LA) and polydiols such as poly(ethylene glycol) and poly(trimethylene ether glycol), were prepared via ring opening polymerization. Glass transition temperatures (T_g) of the obtained PEUs were found strongly dependent on properties of copolymer soft segments. By simply changing composition ratio, type and molecular weight of polydiols in the soft segment preparation step, T_g of PEU can be varied in the broad range of 0–57°C. The synthesized PEUs exhibited shape memory behavior at their transition temperatures. PEUs with hard segment ratio higher than 65 mole percent showed good shape recovery. These findings suggested that it is important to manipulate molecular structure of the copolymer soft segment for a desirable transition temperature and design optimal soft to hard segment ratio in PEU for good shape recovery. Copyright © 2011 John Wiley & Sons, Ltd.