Enhancement of CO2 and Toluene Adsorption on a Rare‐Earth Chalcophosphate Aerogel by Post Synthetic Modification with PdCl2

The sol‐gel metathesis reaction was used to synthesize a new family of aerogels called a rare‐earth chalcophosphate aerogel KY(P₂S₆)₂ · K⁺ and the rare‐earth metal cations Y³⁺ connect [P₂S₆]^2– anions to form an amorphous white gel. Supercritical drying of the resulting gel produced porous materials with a BET surface area of 443 m² · g^–1. The adsorption properties of the rare‐earth chalcophosphate aerogel were studied using volatile organic hydrocarbons (VOCs) and gases as adsorptives. The results showed preferential adsorption of toluene vapor over cyclohexane and cyclopentane vapor. The adsorption capacity toward toluene was 703 mg · g^–1. Favored adsorption of CO₂ over CH₄, N₂, or H₂ was also observed for the aerogel: KY(P₂S₆)₂ (CO₂/H₂: 308, CO₂/CH₄: 67, Co₂/N₂: 177). Pd doped aerogel showed significant enhancement toward toluene (1291 mg · g^–1) for 1 wt % Pd @ KY(P₂S₆)₂, (2064 mg · g^–1) for 3 wt % Pd @ KY(P₂S₆)₂ and (1108 mg · g^–1) for 5 wt % Pd @ KY(P₂S₆)₂. It also showed a noticeable improvement in the gas selectivity (CO₂/H₂: 337, CO₂/CH₄: 85, Co₂/N₂: 205) for 1 wt % Pd @ KY(P₂S₆)₂, (CO₂/H₂: 345, CO₂/CH₄: 109, Co₂/N₂: 212) for 3 wt % Pd @ KY(P₂S₆)₂ and (CO₂/H₂: 319, CO₂/CH₄: 73, Co₂/N₂: 187) for 5 wt % Pd @ KY(P₂S₆)₂.     

Porphyrin‐based covalent triazine frameworks: Porosity,adsorption performance,and drug delivery

Two porous porphyrin‐based covalent triazine frameworks (PCTFs), in which porphyrin is incorporated as building block, have been synthesized by the Friedel–Crafts reaction. The copolymer PCTFs show large Brunauer–Emmett–Teller specific surface area of up to 1089 m² g^?1, high CO₂ uptake capacity reaching 139.9 mg g^?1 at 273 K/1.0 bar, and good selectivity for CO₂/CH₄ adsorption attaining 6.1 at 273 K/1.0 bar. The resulting porous solids also can be used as matrices for drug delivery of ibuprofen in vitro. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55 , 2594–2600     

Carbon Aerogels Synthesizd with Cetyltrimethyl Ammonium Bromide (CTAB) as a Catalyst and its Application for CO2 Capture

A series of carbon aerogels were synthesized by polycondensation of resorcinol and formaldehyde using cetyltrimethyl ammonium bromide (CTAB) as a catalyst. The structure and properties of carbon aerogels were characterized by X‐ray diffraction (XRD), Raman, scanning electron microscope (SEM), Fourier transform infrared spectroscopy (FT‐IR), and N₂ adsorption‐desorption technologies. Besides, the CO₂ capture behavior of carbon aerogels was also investigated. It was found that the amount of CTAB affected the structure and morphology of carbon aerogels, thus influenced the CO₂ adsorption behavior. The sample CA‐125 (the ratio of resorcinol and CTAB is 125) had the highest CO₂ adsorption capacity (63.71 cm³ · g^–1 at 1 bar and 24.14 cm³ · g^–1 at 0.15 bar) at 25 °C. In addition, the higher CO₂ adsorption capacity was ascribed to the higher surface area, pore volume and appropriate pore size, as well as the more defects over carbon aerogels.     

基于1,1’-二苯乙炔-3,3’,5,5’-四羧酸微孔铜配位聚合物的合成和气体吸附性质

本文报道了配合物[Cu2(EBTC)(H2O)2]·8H2O·DMF.DMSO(1,EBTC=1,1′-二苯乙炔-3,3′,5,5′-四羧酸根;DMF=N,N-二甲基甲酰胺;DMSO=二甲基亚砜)的合成、晶体结构和吸附性质。1拥有内径为0.85 nm和0.85 nm×2.15 nm的两种孔洞,分别被6个和12个四羧酸根桥联的[Cu2(CO2)4]螺旋桨式结构围绕,并被EBTC连接成三维超分子结构,该结构拥有可容纳溶剂分子的一维孔道。1为(3,4)-连接的fof(sqc1575)拓扑结构,具有非常大的孔体积,其值高达单位晶胞体积的72.8%。去除溶剂分子后的1a表现出永久孔性,其Langmuir表面积为2844 m2·g-1,BET表面积为1 852 m2·g-1。它对H2、CO2、CH4和C2H2具有可观的气体吸附量和相对较高的吸附焓。特别是,在迄今所有已报道的孔性金属-有机材料中,1a在273 K、1.0×105Pa下,表现出最高的乙炔吸附量(252 cm3·g-1)和很高的吸附焓(吸附量为1 mmol·g-1时的吸附焓为34.5 kJ·mol-1)。     

A Robust 3D Cage‐like Ultramicroporous Network Structure with High Gas‐Uptake Capacity

A three‐dimensional (3D) cage‐like organic network (3D‐CON) structure synthesized by the straightforward condensation of building blocks designed with gas adsorption properties is presented. The 3D‐CON can be prepared using an easy but powerful route, which is essential for commercial scale‐up. The resulting fused aromatic 3D‐CON exhibited a high Brunauer–Emmett–Teller (BET) specific surface area of up to 2247 m² g^?1. More importantly, the 3D‐CON displayed outstanding low pressure hydrogen (H₂, 2.64 wt %, 1.0 bar and 77 K), methane (CH₄, 2.4 wt %, 1.0 bar and 273 K), and carbon dioxide (CO₂, 26.7 wt %, 1.0 bar and 273 K) uptake with a high isosteric heat of adsorption (H₂, 8.10 kJ mol^?1; CH₄, 18.72 kJ mol^?1; CO₂, 31.87 kJ mol^?1). These values are among the best reported for organic networks with high thermal stability (ca. 600 °C).     

Comparison of Gas Sorption Properties of Neutral and Anionic Metal–Organic Frameworks Prepared from the Same Building Blocks but in Different Solvent Systems

Two different 3D porous metal–organic frameworks, [Zn₄O(NTN)₂]?10 DMA?7 H₂O ( SNU‐150 ) and [Zn₅(NTN)₄(DEF)₂][NH₂(C₂H₅)₂]₂?8 DEF?6 H₂O ( SNU‐151 ), are synthesized from the same metal and organic building blocks but in different solvent systems, specifically, in the absence and the presence of a small amount of acid. SNU‐150 is a doubly interpenetrated neutral framework, whereas SNU‐151 is a non‐interpenetrated anionic framework containing diethylammonium cations in the pores. Comparisons of the N₂, H₂, CO₂, and CH₄ gas adsorption capacities as well as the CO₂ adsorption selectivity over N₂ and CH₄ in desolvated SNU‐150′ (BET: 1852 m² g^?1) and SNU‐151′ (BET: 1563 m² g^?1) samples demonstrate that the charged framework is superior to the neutral framework for gas storage and gas separation, despite its smaller surface area and different framework structure.     

Carbon dioxide and nitrogen adsorption on porous copolymers of divinylbenzene and acrylic acid

Porous copolymers of divinylbenzene (DVB) and acrylic acid (AA) having DVB:AA ratios of 6:4, 8:2 and 9:1 were prepared following a distillation-precipitation method, using toluene as the porogenic agent. The materials thus obtained, which showed specific surface area in the range of 380–600 m² g^?1 and pore volume in the range of 0.14–0.18 cm³ g^?1, were investigated as possible adsorbents for CO₂ capture from the flue gas of coal-fired power stations. For that purpose, the isosteric heat of adsorption (and CO₂ adsorption capacity) was analysed from N₂ and CO₂ adsorption equilibrium isotherms obtained over a temperature range. For CO₂, q _st resulted to be in the range of 27–31 kJ mol^?1 (the highest value corresponding to the 6:4 sample), while for N₂ a value of q _st ≈ 12 kJ mol^?1 was obtained. Equilibrium adsorption capacity for CO₂ (at ambient temperature and pressure) showed the value of about 1.35 mmol g^?1. These results are discussed in the broader context of corresponding literature data for CO₂ capture using protonic zeolites.     

Carbon dioxide and methane adsorption at high pressure on activated carbon materials

Granular and monolith carbon materials were prepared from African palm shell by chemical activation with H₃PO₄, ZnCl₂ and CaCl₂ aqueous solutions of different concentrations. Adsorption capacity of carbon dioxide and methane were measured at 298 K and 4,500 kPa, and also of CO₂ at 273 K and 100 kPa, in a volumetric adsorption equipment. Correlations between the textural properties of the materials and the adsorption capacity for both gases were obtained from the experimental data. The results obtained show that the adsorption capacity of CO₂ and CH₄ increases with surface area, total pore volume and micropore volume of the activated carbons. Maximum adsorption values were: 5.77 mmol CO₂ g^?1 at 273 K and 100 kPa, and 17.44 mmol CO₂ g^?1 and 7.61 mmol CH₄ g^?1 both at 298 K and 4,500 kPa.     

Water‐Stable Zirconium‐Based Metal–Organic Framework Material with High‐Surface Area and Gas‐Storage Capacities

We designed, synthesized, and characterized a new Zr‐based metal–organic framework material, NU‐1100 , with a pore volume of 1.53 ccg^?1 and Brunauer–Emmett–Teller (BET) surface area of 4020 m²g^?1; to our knowledge, currently the highest published for Zr‐based MOFs. CH₄/CO₂/H₂ adsorption isotherms were obtained over a broad range of pressures and temperatures and are in excellent agreement with the computational predictions. The total hydrogen adsorption at 65 bar and 77 K is 0.092 g g^?1, which corresponds to 43 g L^?1. The volumetric and gravimetric methane‐storage capacities at 65 bar and 298 K are approximately 180 v_STP/v and 0.27 g g^?1, respectively.     

Influence of supercritical drying fluids on structures and properties of low-density Cu-doped SiO2 composite aerogels

The Cu-doped SiO₂ composite aerogels were successfully prepared by sol–gel process and subsequently supercritical drying with ethanol and CO₂. The Cu-doped SiO₂ composite aerogels had porous texture, low density (<100 mg cm^?3) and high specific surface area (>800 m² g^?1), which were investigated by FESEM and nitrogen adsorption desorption porosimetry. The FTIR spectra of the aerogels showed that the ethanol-dried aerogels had been modified by ethyl while the corresponding CO₂-dried aerogels had more Si–OH groups. The phase structure and thermal stability were investigated by XRD and TGA, respectively. Due to the reducibility of ethanol, the copper was crystalline in ethanol-dried sample. The Cu-doped SiO₂ composite aerogels dried with supercritical ethanol had larger pore diameter and better thermal stability under 400 °C in comparison with CO₂-dried composite aerogels. The structures and properties of Cu-doped SiO₂ composite aerogels are obviously affected by supercritical drying conditions. The effect research could instruct the synthesis of different state of Cu in composite aerogels.     

Liquid density,viscosity and spectroscopic studies of binary mixture of tetraethylene glycol + 1,2-ethanediamine for CO2 capture

Thermophysical properties for binary mixture of tetraethylene glycol (T₄EG) (1) + 1,2-ethanediamine (EDA) (2), a potential scrubbing solution for the absorption of CO₂, are very important as well as lacking in the literatures. This work reports densities and viscosities over the entire concentration range for the binary mixture at T = (293.15-318.15) K under atmospheric pressure. According to the experimental density and viscosity values, the mixtures’ excess molar volume (V_m^E), absolute viscosity deviation (?η), excess free energies of activation (?G*^E), apparent molar volumes, partial molar volumes and isobaric thermal expansion coefficient were calculated, respectively. Meanwhile, the V_m^E, ?η and ?G*^E values were fitted by a Redlich–Kister equation to obtain coefficients. To further study, the Fourier transform infrared, UV-Vis and fluorescence spectra of T₄EG + EDA mixtures with various concentrations were measured, and the intermolecular interaction of T₄EG with EDA was also discussed as the formation of –OCH₂CH₂O–H···N(H₂)CH₂CH₂(H₂)N···.     

Equilibrium isotherms and isosteric heat for CO<Subscript>2</Subscript> adsorption on nanoporous carbons from polymers

Four nanoporous carbons obtained from different polymers: polypyrrole, polyvinylidene fluoride, sulfonated styrene–divinylbenzene resin, and phenol–formaldehyde resin, were investigated as potential adsorbents for carbon dioxide. CO₂ adsorption isotherms measured at eight temperatures between 0 and 60 °C were used to study adsorption properties of these polymer-derived carbons, especially CO₂ uptakes at ambient pressure and different temperatures, working capacity, and isosteric heat of adsorption. The specific surface areas and the volumes of micropores and ultramicropores estimated for these materials by using the density functional theory-based software for pore size analysis ranged from 840 to 1990 m² g^?1, from 0.22 to 1.47 cm³ g^?1, and from 0.18 to 0.64 cm³ g^?1, respectively. The observed differences in the nanoporosity of these carbons had a pronounced effect on the CO₂ adsorption properties. The highest CO₂ uptakes, 6.92 mmol g^?1 (0 °C, 1 atm) and 1.89 mmol g^?1 (60 °C, 1 atm), were obtained for the polypyrrole-derived activated carbon prepared through a single carbonization-KOH activation step. The working capacity for this adsorbent was estimated to be 3.70 mmol g^?1. Depending on the adsorbent, the CO₂ isosteric heats of adsorption varied from 32.9 to 16.3 kJ mol^?1 in 0–2.5 mmol g^?1 range. Overall, the carbons studied showed well-developed microporosity and exceptional CO₂ adsorption, which make them viable candidates for CO₂ capture, and for other adsorption and environmental-related applications.     

Self‐Assembly,Spectroscopic and Electrochemical Studies of Nickel(II)‐4,8‐Diazaundecanediamide Complex

The self‐assembly of NiCl₂·6H₂O with a diaminodiamide ligand 4,8‐diazaundecanediamide (L‐2,3,2) gave a [Ni(C₉H₂₀N₄O₂)(Cl)(H₂O)] Cl·2H₂O ( 1 ). The structure of 1 was characterized by single‐crystal X‐ray diffraction analysis. Structural data for 1 indicate that the Ni(II) is coordinated to two tertiary N atoms, two O atoms, one water and one chloride in a distorted octahedral geometry. Crystal data for 1: orthorhombic, space group P 21nb, a = 9.5796(3) Å, b = 12.3463(4) Å, c = 14.6305(5) Å, Z = 4. Through NH···Cl–Ni (H···Cl 2.42 Å, N···Cl 3.24 Å, NH···Cl 158°) and OH···Cl–Ni contacts (H···Cl 2.36 Å, O···Cl 3.08 Å, OH···Cl 143°), each cationic moiety [Ni(C₉H₂₀N₄O₂) (Cl)(H₂O)]⁺ in 1 is linked to neighboring ones, producing a charged hydrogen‐bonded 1D chainlike structure. Thermogrametric analysis of compound 1 is consistent with the crystallographic observations. The electronic absorption spectrum of Ni(L‐2,3,2)²⁺ in aqueous solution shows four absorption bands, which are assigned to the ³A_2g → ³T_2g, ³T_2g → ¹Eg, ³T_2g → ³T_1g, and ³A_2g → ³T_1g transitions of triplet‐ground state, distorted octahedral nickel(II) complex. The cyclic volammetric measurement shows that Ni²⁺ is more easily reduced than Ni(L‐2,3,2)²⁺ in aqueous solution.     

A Polyhedron‐based Metal‐Organic Framework showing high CO2 Adsorption Capacity

A novel porous copper‐based metal‐organic framework {[Cu₂(TTDA)₂]*(DMA)₇}_n ( 1 ) (DMA = N,N‐dimethylacetamide) was designed and synthesized via the combination of a dual‐functional organic linker 5′‐(4‐(4H‐1,2,4‐triazol‐4‐yl)phenyl)‐[1,1′:3′,1′′‐terphenyl]‐4,4′′‐dicarboxylic acid (H₂TTDA) and a dinuclear Cu^II paddle‐wheel cluster. This MOF is characterized by elemental analysis, powder X‐ray diffraction (PXRD), thermo gravimetric analysis (TGA), and single‐crystal X‐ray diffraction. The framework is constructed from two types of cages (octahedral and cuboctahedral cages) and exhibits two types of circular‐shaped channels of approximate size of 5.8 and 11.4 Å along the crystallographic c axis. The gas sorption experiments indicate that it possesses a large surface area (1687 m² · g^–1) and high CO₂ adsorption capacities around room temperature (up to 172 cm³ · g^–1 at 273 K and 124 cm³ · g^–1 at 298 K).     

Control of Interpenetration and Gas‐Sorption Properties of Metal–Organic Frameworks by a Simple Change in Ligand Design

In metal–organic framework (MOF) chemistry, interpenetration greatly affects the gas‐sorption properties. However, there is a lack of a systematic study on how to control the interpenetration and whether the interpenetration enhances gas uptake capacities or not. Herein, we report an example of interpenetration that is simply controlled by the presence of a carbon–carbon double or single bond in identical organic building blocks, and provide a comparison of gas‐sorption properties for these similar frameworks, which differ only in their degree of interpenetration. Noninterpenetrated ( SNU‐70 ) and doubly interpenetrated ( SNU‐71 ) cubic nets were prepared by a solvothermal reaction of [Zn(NO₃)₂] ? 6 H₂O in N,N‐diethylformamide (DEF) with 4‐(2‐carboxyvinyl)benzoic acid and 4‐(2‐carboxyethyl)benzoic acid, respectively. They have almost‐identical structures, but the noninterpenetrated framework has a much bigger pore size (ca. 9.0×9.0 Å) than the interpenetrated framework (ca. 2.5×2.5 Å). Activation of the MOFs by using supercritical CO₂ gave SNU‐70′ and SNU‐71′ . The simulation of the PXRD pattern of SNU‐71′ indicates the rearrangement of the interpenetrated networks on guest removal, which increases pore size. SNU‐70′ has a Brunauer–Emmett–Teller (BET) surface area of 5290 m² g^?1, which is the highest value reported to date for a MOF with a cubic‐net structure, whereas SNU‐71′ has a BET surface area of 1770 m² g^?1. In general, noninterpenetrated SNU‐70′ exhibits much higher gas‐adsorption capacities than interpenetrated SNU‐71′ at high pressures, regardless of the temperature. However, at P<1 atm, the gas‐adsorption capacities for N₂ at 77 K and CO₂ at 195 K are higher for noninterpenetrated SNU‐70′ than for interpenetrated SNU‐71′ , but the capacities for H₂ and CH₄ are the opposite; SNU‐71′ has higher uptake capacities than SNU‐70′ due to the higher isosteric heat of gas adsorption that results from the smaller pores. In particular, SNU‐70′ has exceptionally high H₂ and CO₂ uptake capacities. By using a post‐synthetic method, the C?C double bond in SNU‐70 was quantitatively brominated at room temperature, and the MOF still showed very high porosity (BET surface area of 2285 m² g^?1).     

Preparation and Gas Separation Properties of Metal‐Organic Framework Membranes

Continuous and intergrown metal‐organic framework (MOF) membranes, MIL‐100(In) (MIL represents Materials Institute Lavoisier), were prepared directly on porous anodic alumina oxide (AAO) membranes using an in situ crystallization method. The pore surface of MIL‐100(In) is conferred with polarity due to the presence of the 1, 3,5‐benzenetricarboxylic acid. The thickness of MIL‐100(In) membranes was tuned by varying the reactant concentration of indium chloride and 1, 3,5‐benzenetricarboxylic acid. Single gas permeation measurements on this MOF membrane indicate the large permeances of 0.90 × 10^–6 and 0.81 × 10^–6 mol · m^–2·s^–1·Pa^–1 for CO₂ and CH₄, and relatively high ideal selective factors of 3.75 and 3.38 for CO₂/N₂ and CH₄/N₂, respectively.     

Synthesis of high surface area nanometer magnesia by solid-state chemical reaction

Nanometer MgO samples with high surface area, small crystal size and mesoporous texture were synthesized by thermal decomposition of MgC₂O₄ · 2H₂O prepared from solid-state chemical reaction between H₂C₂O₄ · 2H₂O and Mg (CH₃COO)₂ · 4H₂O. Steam produced during the decomposition process accelerated the sintering of MgO, and MgO with surface area as high as 412 m² · g⁻¹ was obtained through calcining its precursor in flowing dry nitrogen at 520°C for 4 h. The samples were characterized by X-ray diffraction, N₂ adsorption, transmission electron microscopy, thermogravimetry, and differential thermal analysis. The as-prepared MgO was composed of nanocrystals with a size of about 4–5 nm and formed a wormhole-like porous structure. The MgO also had good thermal stability, and its surface areas remained at 357 and 153 m²·g⁻¹ after calcination at 600 and 800°C for 2 h, respectively. Compared with the MgO sample prepared by the precipitation method, MgO prepared by solid-state chemical reaction has uniform pore size distribution, surface area, and crystal size. The solid-state chemical method has the advantages of low cost, low pollution, and high yield, therefore it appears to be a promising method in the industrial manufacture of nanometer MgO. Translated from Chinese Journal of Catalysis, 2006, 27(9): 793–798 (in Chinese)     

Photo-responsive azo MOF exhibiting high selectivity for CO2 and xylene isomers

A combination of azo and acylamide ligands is used in the preparation of metal–organic frameworks. Light response research reveals that under UV–vis irradiation, the CO₂ adsorption of 1 declines as much as 21.4%. 1 exhibits excellent CO₂ adsorption selectivity over CH₄, O₂, CO, and N₂ gasses with IAST selectivity of 21–580 at 293 K. This MOF also has promising potential in separation of xylene isomers in the liquid phase with the adsorption of p-xylene of 265.15, o-xylene of 101.25 and m-xylene of 0 mg g^?1, respectively.     

Nanocage containing metal-organic framework constructed from a newly designed low symmetry tetra-pyrazole ligand

1368-Tetra(1H-pyrazol-4-yl)-9H-carbazole (H₄CTP), a tetra-pyrazole ligand with C_s symmetry, has been synthesized based on a carbazole core. A solvothermal reaction of this ligand with NiCl₂·6H₂O gave a three-dimensional (3-D) metal-organic framework (MOF), [Ni(H₄CTP)Cl₂]·nS (BUT-41), which crystallized in the cubic space group Pm-3 in spite of H₄CPT with a central carbazole core and four peripheral pyrazole rings has low symmetry. The framework of BUT-41 can be regarded as a four-connected 3-D net with the rhr topology when both the organic ligand and the metal center are considered as four-connected nodes. Nanocages with internal diameter of 2 nm are present in the framework of BUT-41, which are formed by interconnecting 12 H₄CTP ligands and 20 Ni(II) ions. Each nanocage connects with six adjacent cages through sharing hexagonal windows with diameter over 7 Å, resulting in 3-D intersecting channels of the MOF. Although the tetra-pyrazole ligand is not deprotonated after coordination with the metal ions, powder X-ray diffraction and N₂ adsorption experiments reveal that the framework of BUT-41 is rigid and permanently porous with the Brunauer-Emmett-Teller surface area up to 1551 m² g^?1. Furthermore, gas adsorption experiments show that this MOF selectively adsorbs CO₂ over N₂ and CH₄.     

[{(CH3)3Si}3C–Li–C{Si(CH3)3}3][Li · 3(OC4H8)] und {(CH3)3Si}3C–Li · O=C(Si(CH3)3)2, zwei neue Addukte des Lithium‐trisylmethanids

[{(CH₃)₃Si}₃C–Li–C{Si(CH₃)₃}₃][Li · 3(OC₄H₈)] and {(CH₃)₃Si}₃C–Li · O=C(Si(CH₃)₃)₂, two New Adducts of Lithium Trisylmethanide Sublimation of (Tsi–Li) · 2 THF (Tsi = –C(Si(CH₃)₃)₃) at 180 °C and 10^–4 hPa gives (Tsi–Li) · 1.5 THF in very low yield. The X‐ray structure determination shows an almost linear [Tsi–Li–Tsi]^– anion connected by short agostic Li…C contacts with the threefold THF‐coordinated Li‐cation. Base‐free Tsi–Li, solved in toluene is decomposed by oxygen, forming the strawberry‐colored ketone O=C(SiMe₃)₂, which forms an 1 : 1 adduct with undecomposed Tsi–Li. The X‐ray structure elucidation of this compound is also discussed.