Catalytic activity of lipase immobilized onto ultrathin films of cellulose esters

Ultrathin (approximately 2.0 nm) films of cellulose acetate (CA), cellulose acetate propionate (CAP), and cellulose acetate butyrate (CAB) supported on Si wafers have been prepared by adsorption and characterized by means of ellipsometry, atomic force microscopy (AFM), and contact angle measurements. CA, CAP, and CAB ultrathin films were characterized in air just after their formation and after annealing under reduced pressure at temperature higher than the corresponding melt temperature. Upon annealing, CA, CAP, and CAB ultrathin films became smoother and more hydrophobic, evidencing molecular reorientation at the solid-air interface. CA, CAP, and CAB films were used as supports for the immobilization of lipase. The adsorption of lipase onto annealed films was more pronounced than that onto untreated films, showing the strong affinity of lipase for the more hydrophobic substrates. Enzymatic activity was evaluated by a standard procedure, namely, (spectrophotometric) measurement of p-nitrophenol, the product formed from the hydrolysis of p-nitrophenyl dodecanoate (p-NPD). Lipase immobilized onto hydrophobic films exhibited higher activity than that of free lipase and could be recycled three times while retaining relatively high activity (loss of ca. 30% of original enzymatic activity). The effect of storing time on the activity of immobilized lipase was studied. Compared with free lipase, that immobilized onto more hydrophobic films retained 70% activity after 1 month. More importantly, the latter level of activity is similar to that of free lipase. However, lipase immobilized onto more hydrophilic films retained 50% and 30% activity after 20 and 30 days, respectively. These results are explained in terms of surface wettability and the contribution of the interactions between the polar residues of lipase and the glucopyranosyl moieties of cellulose ester to maintain the natural conformation of immobilized enzyme.     

Characteristics of thin cellulose ester films spin-coated from acetone and ethyl acetate solutions

Spin-coated films of cellulose acetate (CA), cellulose acetate propionate (CAP), cellulose acetate butyrate (CAB) and carboxymethylcellulose acetate butyrate (CMCAB) have been characterized by ellipsometry, atomic force microscopy (AFM) and contact angle measurements. The films were spin-coated onto silicon wafers, a polar surface. Mean thickness values were determined by means of ellipsometry and AFM as a function of polymer concentration in solutions prepared either in acetone or in ethyl acetate (EA), both are good solvents for the cellulose esters. The results were discussed in the light of solvent evaporation rate and interaction energy between substrate and solvent. The effects of annealing and type of cellulose ester on film thickness, film morphology, surface roughness and surface wettability were also investigated. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Solution behavior and surface properties of carboxymethylcellulose acetate butyrate

Solution behavior of carboxymethylcellulose acetate butyrate (CMCAB) in acetone and ethyl acetate has been investigated by small-angle X-ray scattering (SAXS) and capillary viscometry and correlated with the characteristics of CMCAB films. Viscosity and SAXS measurements showed that ethyl acetate is a better solvent than acetone for CMCAB. Thin films of CMCAB were deposited onto silicon wafers (Si/SiO₂) by spin coating. AFM images revealed that CMCAB spin coated films from solutions prepared in ethyl acetate were homogeneous and flat. However, films obtained from solutions in acetone were very rough. Contact angle measurements with polar and apolar test liquids characterized CMCAB surfaces as hydrophobic and allowed estimating the surface energy of CMCAB. Sum frequency generation vibrational spectroscopy was used to understand the role played by solvents and to gain insight about molecular orientation at Si/SiO₂/CMCAB interface.     

Model films of cellulose ID – improved preparation method and characterization of the cellulose film

An optimization study of the preparation of spin-coated cellulose model films from the NMMO/DMSO system on silicon wafers has been made. The study shows that the cellulose concentration ID the solution determines the cellulose film thickness and that the temperature of the solution affects the surface roughness. A lower solution temperature results ID a lower surface roughness at cellulose concentrations below 0.8%. Using the described method, ID ID possible to prepare films with thicknesses of 30–90 nm with a constant surface roughness by changing the cellulose concentration, i.e. by dilution with DMSO. On these films, water has a contact angle less than 20° and about 50% of the material can, according to CP/MAS ¹³C-NMR spectroscopy on corresponding fibrous material, be considered to consist of crystalline cellulose ID type material. ID has further been shown that AFM can be used to determine the thickness of cellulose films, ID both dry and wet states. ID this method, the difference ID height between the top surface and the underlying wafer has been measured at an incision made into the cellulose film. The cellulose films have also been spin-coated with the same technique as on the silicon oxide wafer onto the crystal ID a quartz crystal microbalance (QCM). These model films were found to be suitable for swelling measurements with the QCM. The films were very stable during this type of measurement and films with different amounts of charges gave different swelling responses depending on their charges. As expected, films with a higher charge showed a higher swelling.     

Effect of humidity and solvent vapor phase on cellulose esters films

In the present study the effect of relative humidity (RH) during spin-coating process on the structural characteristics of cellulose acetate (CA), cellulose acetate phthalate (C-A-P), cellulose acetate butyrate (CAB) and carboxymethyl cellulose acetate butyrate (CMCAB) films was investigated by means of atomic force microscopy (AFM), ellipsometry and contact angle measurements. All polymer solutions were prepared in tetrahydrofuran (THF), which is a good solvent for all cellulose esters, and used for spin-coating at RH of (35 ± 5)%, (55 ± 5)% or (75 ± 5)%. The structural features were correlated with the molecular characteristics of each cellulose ester and with the balance between surface energies of water and THF and interface energy between water and THF. CA, CAB, CMCAB and C-A-P films spin-coated at RH of (55 ± 5)% were exposed to THF vapor during 3, 6, 9, 60 and 720 min. The structural changes on the cellulose esters films due to THF vapor exposition were monitored by means of AFM and ellipsometry. THF vapor enabled the mobility of cellulose esters chains, causing considerable changes in the film morphology. In the case of CA films, which are thermodynamically unstable, dewetting was observed after 6 min exposure to THF vapor. On the other hand, porous structures observed for C-A-P, CAB and CMCAB turned smooth and homogeneous after only 3 min exposure to THF vapor.     

三甲基氯硅烷对纳米多孔二氧化硅薄膜的修饰

以正硅酸乙酯为先驱体,采用溶胶-凝胶法,结合旋转涂胶、超临界干燥工艺在硅片上制备了纳米多孔SiO2薄膜.用三甲基氯硅烷(TMCS)对该SiO2薄膜进行了表面修饰,采用FTIR、TG-DTA、AFM和椭偏仪等方法研究了TMCS修饰前后薄膜的结构、形貌、厚度与介电常数等性能.超临界干燥后的SiO2薄膜含有Si－O－Si与Si－OR结构,呈疏水性.在空气中250 ℃以上热处理后SiO2薄膜因含有Si－OH而呈吸水性. TMCS修饰后的SiO2薄膜在温度不高于450 ℃时可保持其疏水性和多孔结构. SiO2薄膜经TMCS修饰后基本粒子和孔隙尺寸增大,孔隙率提高,介电常数可降低至2.5以下.     

Langmuir-Blodgett films of cellulose nanocrystals: preparation and characterization

The goal of this work is the preparation of monolayers of cellulose I nanocrystals providing flat crystalline cellulose surfaces. Suspensions of cellulose nanocrystals were prepared by hydrolyzing ramie and tunicin fibers with sulfuric acid. Due to surface grafted sulfate groups, the negatively charged, rod-like cellulose nanocrystals were found to form stable layers at the air-water interface in the presence of a cationic amphiphilic molecule such as dioctadecyldimethylammonium (DODA) used in this work. These layers were formed at different cellulose-DODA weight ratios, compressed and analyzed by tensiometry, ellipsometry and Brewster angle microscopy. At low cellulose concentrations the layers are discontinuous, becoming dense and homogeneous upon reaching a critical weight ratio, which depends on the aspect ratio of the cellulose nanocrystals. After transfer onto silicon wafers, the surface composition and morphology as well as the thickness of the films were examined by X-ray photoelectron spectroscopy, ellipsometry and atomic force microscopy. The results indicate that they are monolayer films, well structured, relatively smooth and pure. These films offer a crystalline and easily reproducible model cellulose surface.     

Atomically flat gold on elastomeric substrate

We present a procedure to fabricate extremely smooth Au films supported on thin elastomeric (PDMS) substrates. Minimum rms roughness and largest grain size are obtained using Si wafers, coated with native oxide and release layers, as templates for the growth of thermally evaporated Au films. The wafers are held at a temperature of 300 degrees C during deposition. The Au films, up to 200 nm thick, are then transferred onto poly(dimethylsiloxane) substrates which have been previously surface-functionalized with a (3-mercaptopropyl)trimethoxysilane adhesion layer. The resulting Au films have been found by AFM to be extremely smooth with rms-roughness 2.5-4 angstroms and to exhibit a crystalline morphology with flat grains >500 nm in size. Thinner films, down to 20 nm, are grown at lower temperature and are comparably smooth, but with a loss in crystalline morphology. We compare the results of this optimized procedure with other gold films grown on mica sheets as templates and to those produced using Ti-O-Si interfacial chemistry.     

A photoluminescent switch based on the hybrid organized molecular films of decatungsteuropate and some amphiphiles

Hybrid organized molecular films composed of a polyoxometalate, decatungsteuropate (EuW(10)), and amphiphiles such as hexadecyltrimethylammonium bromide (CTAB), n-octadecylamine (ODA) and 4-hexadecylaniline (HDA) were fabricated by Langmuir-Blodgett (LB) technique and their photoluminescent properties were investigated. The hybrid films, which were formed through in situ complex formation at the air/water interface and subsequently transferred onto the solid substrate, were characterized by UV-vis, FT-IR, fluorescence, and AFM measurements. The transferred hybrid films showed red emission characteristic of the Eu(III) ion upon UV irradiation. The photoluminescence of the hybrid films was sensitive to the acid and base gases. When ODA/EuW(10) and HDA/EuW(10) hybrid films were exposed to HCl gas, their photoluminescence disappeared completely. Interestingly, the photoluminescence was recovered upon subsequent exposing the same film to NH(3) gas. Such process could be repeated many times and a switch based on these hybrid films was proposed. On the other hand, the photoluminescent intensity of CTAB/EuW(10) film decreased but never disappeared upon exposing to HCl gas. Similarly, the photoluminescence could also be partially recovered upon exposing to NH(3) gas. Detailed investigation on the spectral changes of the films revealed that the interaction between EuW(10) and CTAB and was different from EuW(10) with ODA or HDA, and protonation of amine group in ODA or HDA induced by HCl gas played an important role in realizing the "on" and "off" photoluminescence switch of the hybrid films.     

阳极氧化TiN薄膜制备N掺杂纳米TiO2薄膜及其可见光活性

室温下通过电泳沉积(EPD)的方法在Ti片表面制备TiN薄膜, 然后对TiN薄膜进行阳极氧化得到N掺杂多孔纳米结构的TiO2薄膜. 利用X射线衍射(XRD), X射线光电子能谱(XPS), 扫描电子显微镜(SEM)及光电化学方法对得到的薄膜进行表征. XRD测试结果表明, 经过阳极氧化并在350 ℃空气气氛中退火1 h的薄膜中存在锐钛矿晶型的TiO2. XPS的结果表明, 样品中的N元素取代部分O, 且N的摩尔分数为0.95%. SEM显示, 经阳极氧化后薄膜表面出现多孔纳米结构. 光电化学测试结果显示, 阳极氧化提高了N掺杂TiO2薄膜在可见光下的光电响应. 经阳极氧化并热处理的薄膜在0 V电位及可见光照射下光电流密度为2.325 μA·cm-2, 而单纯热处理的薄膜在相同条件下光电流密度仅为0.475 μA·cm-2. 阳极氧化得到纳米多孔结构提高了N掺杂纳米TiO2薄膜的表面积, 从而对可见光的响应增大.     

A comparative Langmuir-Blodgett study on a set of covalently linked porphyrin-based amphiphiles: a detailed atomic force microscopic study

A set of covalently linked phenyl-amidophenyl-substituted porphyrin amphiphiles with n-C15H31 tails have been synthesized and completely characterized. These amphiphiles form good Langmuir-Blodgett (LB) films at the air/water interface. Mean molecular areas for the series were measured from the isotherms and found to increase as the number of aliphatic chains increased from one to four. No influence of the subphase pH was observed on the isotherms. LB films can be transferred successfully onto different solid surfaces. The LB films were characterized using tapping mode atomic force microscopy (AFM). Bis-, tris-, and tetra-substituted porphyrins were found to be fairly good film-forming amphiphiles, whereas irregular aggregates were seen in the case of the monosubstituted porphyrin amphiphile. Multilayers were also formed with tetra-substituted amphiphiles on mica. Detailed AFM studies of tetra-substituted amphiphiles have been carried out to investigate the effect of preparation procedure and solid substrates on film formation and transfer. The absorption and fluorescence spectra for the amphiphiles in solution and LB films deposited onto mica and glass were recorded, which demonstrated the successful transfer of LB films onto the substrates and provided more information about the arrangement of porphyrin molecules within the LB films. For comparison, self-assembled monolayers (SAMs) and the cast thin films of the amphiphiles were prepared and characterized.     

Colloidal interactions between asphaltene surfaces in aqueous solutions

Asphaltene at oil/water interfaces plays a dominant role in the recovery of crude oil. In this study, asphaltene monolayer films were deposited on hydrophobic silicon wafers and silica spheres from oil-water interfaces using a Langmuir interfacial trough. The morphology of the deposited asphaltene films was characterized with an atomic force microscope (AFM). The colloidal forces between the prepared asphaltene films in aqueous solutions were measured with AFM to shed light on the stabilization of water or oil droplets coated with asphaltene films. Factors such as solution pH, KCl concentration, calcium addition, and temperature all showed a strong impact on colloidal forces between the prepared asphaltene films. The findings provided a better understanding of asphaltene interfacial films at an oil/water interface in stabilizing bitumen-in-water and water-in-bitumen emulsions.     

Colloidal liquid crystal type assemblies of spheroidal polystyrene core/polyglycidol‐rich shell particles (P[S/PGL]) formed at the liquid‐silicon‐air interface by a directed dewetting process

A method for the preparation of stripe‐like monolayers of microspheroids is described. The particles were obtained from polystyrene core/polyglycidol‐rich shell microspheres by stretching poly (vinyl alcohol) films that contain embedded particles. The stretching was performed under controlled conditions at temperatures above the T_g of the films and particles. The elongated films were dissolved in water, and the microspheroids were subsequently removed and purified from the poly (vinyl alcohol). The aspect ratio (AR) of the particles, which denotes the ratio of the lengths of the longer to shorter particle axes, was determined by the film elongation. The AR values were in the range of 2.9‐7.7. Spheroidal particles with various ARs were deposited onto silicon wafers from an ethanol (EtOH) suspension. The particle concentration and volume of the suspension were the same in each experiment. Evaporation of the EtOH yielded stripes of spherical particles packed into nematic‐type colloidal crystals and assembled into monolayers. The orientation of the stripes after ethanol evaporation was perpendicular to the triphasic (silicon‐ethanol‐air) interface along the silicon substrate. The adsorbed stripes on the wafers were characterized in terms of their interstripe distance (ID), stripe width, and crystal domain size. Nematic‐type spheroid arrangements in the stripes were the dominant structure, which enabled denser packing of the particles into colloidal crystals than that allowed by the smectic‐type arrangements. Furthermore, the number of spheroids adsorbed per surface unit of the silicon wafers was similar for all ARs, but the width and frequency of the spheroid stripes adsorbed on the wafers were different.     

Multitechnique characterization of thin films of immiscible polymer systems: PS–b‐PMMA diblock copolymers and PS–PMMA symmetric blends

Immiscible polymer systems are known to form various kinds of phase‐separated structures capable of producing self‐assembled patterns at the surface. In this study, different surface characterization methods were utilized to study the surface morphology and composition produced after annealing thin polymer films. Two different SIMS techniques—static time‐of‐flight secondary ion mass spectrometry (ToF‐SIMS) and dynamic nano‐SIMS—were used, complemented by x‐ray photoelectron spectrometry (XPS) and atomic force microscopy (AFM). Thin films (spin‐coated onto silicon wafers) of polystyrene (PS)–poly(methyl methacrylate) (PMMA) symmetric blends and diblock copolymers of similar molecular weight were investigated. Surface enrichment by PS was found on all as‐cast samples. The samples were annealed at 160 °C for different time periods, after which the blend and the copolymer films exhibited opposite behaviour as seen by ToF‐SIMS and XPS. The annealed blend surface presented an increase in the PMMA concentration whereas that of copolymers showed a decrease in PMMA concentration compared with the as‐cast sample. For blends, the nano‐SIMS as well as AFM images revealed the formation of phase‐separated domains at the surface. The composition information obtained from ToF‐SIMS and XPS, as well as the surface mapping by nano‐SIMS and AFM, allowed us to conclude that PS formed phase separated droplet‐like domains on a thin PMMA matrix on annealing. The three‐dimensional nano‐SIMS images showed that the PS droplets were supported inside a rim of PMMA and that these droplets continued from the surface like columnar rods into the film until the substrate interface. In the case of annealed copolymer samples, the AFM images revealed topographical features resembling droplet‐like domains on the surface but there was no phase difference between the domains and the matrix. In the case of copolymers, owing to the covalent bonding between the blocks, complete phase separation was not possible. The three‐dimensional nano‐SIMS images showed domain structures in the form of striations inside the film, which were not continuous until the substrate interface. Information from the different techniques was required to gain an accurate view of the surface composition and topographical changes that have occurred under the annealing conditions. Copyright © 2005 John Wiley & Sons, Ltd.     

Surface forces measurements of spin-coated cellulose thin films with different crystallinity

A systematic study of the surface forces between a cellulose sphere and cellulose thin films of varying crystallinity has been conducted as a function of ionic strength and pH. Semicrystalline cellulose II surfaces and amorphous cellulose films were prepared by spin-coating of the precursor cellulose solutions onto oxidized silicon wafers before regeneration in water. Crystalline cellulose I surfaces were prepared by spin-coating wafers with aqueous suspensions of sulfate-stabilized cellulose I nanocrystals. These preparation methods produced thin, smooth films suitable for surface forces measurements. The interaction with the cellulose I was monotonically repulsive at pH 3.5, 5.8, and 8.5 and at 0.1, 1, and 10 mM ionic strengths. This was attributed to the presence of strongly ionizable sulfur-containing groups on the cellulose nanocrystal surfaces. The amorphous film typically showed a steric interaction up to 100 nm away from the interface that was independent of the solution conditions. A range of surface forces were successfully measured on the semicrystalline cellulose II films; attractive and repulsive regimes were observed, depending on pH and ionic strength, and were interpreted in terms of van der Waals and electrostatic interactions. Clearly, the forces acting near cellulose surfaces are very dependent on the way the cellulose surface has been prepared.     

Sisal cellulose and its acetates: generation of films and reinforcement in a one-pot process

This study was undertaken to evaluate both the properties of cellulose acetate films as a function of their degree of substitution (DS) and the possibility of generating reinforcements during film preparation. Sisal was selected for the entire study, among other reasons, because it is a rapidly growing source of cellulose. Cellulose acetates with various DS values were prepared in a homogeneous medium (dimethylacetamide/lithium chloride as the solvent system) and characterized. In DMAc/LiCl, cellulose and cellulose acetate films (mixed or not mixed with sisal cellulose) were successfully prepared and characterized. The films with high DS values exhibited lower hygroscopicity, a distinct morphology (scanning electron microscopy images), and lower tensile strength. In some cases, the films prepared from acetates/cellulose exhibited higher tensile strength and/or storage modulus than the acetate films. This result suggested a reinforcing action of the auto-organized cellulose chains that enabled the generation of both a film and reinforcement in a one-pot process.     

微波法制备聚(苯乙烯-N-异丙基丙烯酰胺)热敏性微球

聚(N-异丙基丙烯酰胺)(PNIPAM),由于其大分子链上同时具有亲水性的酰氨基和疏水性的异丙基,使得PNIPAM的水溶液,在32℃附近具有最低临界溶液温度(LCST)．PNIPAM及其共聚物表现出相转变,产生热敏性质．利用PNIPAM的热敏性质,可以制备多种智能高分子材料．这些高分子材料在生物医学、免疫分析、     

EFFECT OF COMPOSITION AND PROCESSING CONDITION ON MICROSTRUCTURAL PROPERTIES AND DURABILITY OF FLUOROPOLYMER/ACRYLIC BLENDS

Fluoropolymer blends have been widely used as binders for exterior coatings because of their excellent resistance to ultra-violet (UV) radiation as well as to many corrosive chemical agents.It is known that the fluorinated component usually has a lower glass transition temperature and easily crystallizes in the final structure depending upon the blend composition and sample annealing condition.We investigated the effect of blend composition and annealing process (slow and fast cooling) on the surface mor...     

EFFECT OF COMPOSITION AND PROCESSING CONDITION ON MICROSTRUCTURAL PROPERTIES AND DURABILITY OF FLUOROPOLYMER/ACRYLIC BLENDS

 Fluoropolymer blends have been widely used as binders for exterior coatings because of their excellent resistance to ultra-violet (UV) radiation as well as to many corrosive chemical agents. It is known that the fluorinated component usually has a lower glass transition temperature and easily crystallizes in the final structure depending upon the blend composition and sample annealing condition. We investigated the effect of blend composition and annealing process (slow and fast cooling) on the surface morphology and microstructure a poly(vinylidene fluoride)/poly(methyl methacrylate) (PVDF/PMMA) blend before and after UV exposure. Surface and subsurface microstructures were studied by atomic force microscopy (AFM) and laser scanning confocal microscopy (LSCM). Bulk microstructure of PVDF-coatings before and after UV exposure were characterized using small angle neutron and light scattering. Higher PVDF content and a slow cooling process result in larger spherulite crystallite structure and rougher surface morphology. Significant ordering in the spherulite crystallite structure has been observed on the surface and the bulk films after UV exposure.     

Enzymatic degradation of model cellulose films

Enzymatic degradation of model cellulose films prepared by a spin-coating technique was investigated by ellipsometry. The cellulose films were prior to degradation characterized by ellipsometry, contact angle measurements, ESCA (electron spectroscopy for chemical analysis) and AFM (atomic force microscopy). At enzyme addition to preformed cellulose films an initial adsorption was observed, which was followed by a total interfacial mass decrease due to enzymatic degradation of the cellulose films. The degradation rate was found to be constant during an extended time of hours, whereafter the degradation leveled off. In parallel to the decreased interfacial mass, the cellulose degradation resulted in a thinner and more dilute interfacial film. At long degradation times, however, there was an expansion of the cellulose film. The enzyme concentration affected the degradation rate significantly, with a faster degradation at a higher enzyme concentration. The effects of pH, temperature, ionic strength and stirring rate in the cuvette were also investigated.