Closed-vessel miniaturised microwave-assisted EDTA extraction to determine trace metals in plant materials

The demonstration of an innovative miniaturised closed-vessel microwave-assisted extraction (µMAE) method under the use of EDTA (µMAE-EDTA) for determination of trace metal contents in grassland (Lolio-Cynosuretum) was examined by ICP-OES. The evaluation of the method was done by comparison of the results with another miniaturised closed-vessel microwave HNO₃ method (µMAE-H) and with a macro-scale microwave procedure (MAE-H). Concerning their homogeneity certified plant reference materials (CRMs) were used for validation of the applicability of µMAE-EDTA procedure. For CRMs and 72 real plant samples, no significant differences were found between µMAE-EDTA and MAE-H in the determination of Cd, Co, Cu, Mn, Ni, Pb, and Zn contents. Recovery rates achieved from µMAE-EDTA for CRMs ranged between 100.0–102.6% for the investigated elements. The key characteristics of µMAE-EDTA for determination of trace metal contents in plant samples are: (i) suitability as a high-throughput procedure; (ii) consumption of minimum volume of extracting agent and minimum amount of sample; and (iii) combination of fast, safe and environmentally friendly extraction procedure.     

Influence of digestion methods on the determination of total Al in food samples by ICP-ES

Summary To determine total Al in a variety of food and total diet samples using ICP-ES, HF pre-treatment, prior to wet digestion (HNO₃/HClO₄) seems to be necessary. Compared with results obtained after HF pre-treatment, the determination of Al using pressure microwave digestion with HNO₃ or HNO₃/HClO₄ digestion recovered only between 25–50% Al for dried spinach and flour and 40–75% for total diet samples, respectively. In most cases the addition of 0.25 ml HF (40%) per gram dry mass resulted in maximum Al yield. The results are in acceptable agreement with those obtained by neutron activation analysis (NAA).     

Characteristics of a novel UV-TiO2-microwave integrated irradiation device in decomposition processes

The efficiency of oxidation in wet decomposition procedures for organic materials can be of great importance to the quality of the analytical data from various measurement techniques. A novel, microwave-assisted, high-temperature/high-pressure UV-TiO₂ digestion procedure was developed for the accelerated decomposition of various biological samples. The technique is based on a closed, pressurized, microwave digestion apparatus (MW). UV irradiation is generated by immersed electrodeless Cd discharge lamp operated by the focused microwave field in the single polymer vessel. To enhance oxidation efficiency, a photocatalyst TiO₂ was added to the microwave heated Teflon bomb. Measures of digestion completeness were provided by the appearance of carbon content and determination of trace and minor elements, enabling a comparison of different digestion procedures and sample types. Compared with other digestion systems, unusually low residual carbon contents were obtained. For the organic compounds and biological samples digested, the residual carbon content was 1-2%, corresponding to a decomposition efficiency of 98-99%. The potential of the MW-UV-TiO₂ system was illustrated by the decomposition of four certified reference materials (serum, urine, milk, arsenobetaine solution) and subsequent determination of trace and minor elements. Recoveries between 92% and 107% were found.     

Trace element analysis in CRM of plant origin by inductively coupled plasma mass spectrometry

Three CRMs of plant origin (SRM 1515 Apple Leaves, SRM 1570a Trace Elements in Spinach Leaves, and SRM 1575 Pine Needles) were used for analytical quality assurance of Cr, Mn, Fe, Co, Ni, Cu, Zn, As, Mo, Cd, and Pb determination by ICP-MS. The samples were decomposed using microwave assisted pressurized digestion by HNO₃ and HNO₃ + H₂O₂ mixture and temperature programmed dry ashing. Concentrations of elements in samples were evaluated by external calibration. All samples, blanks, and standards were spiked to 100 μg/L concentration of In and Bi as internal standards. During the measurement, signals of ⁵²Cr, ⁵³Cr, ⁵⁴Fe, ⁵⁵Mn, ⁵⁹Co, ⁶⁰Ni, ⁶²Ni, ⁶³Cu, ⁶⁵Cu, ⁶⁶Zn, ⁹⁵Mo, ¹¹¹Cd, ¹¹²Cd, ¹¹⁵In, ²⁰⁶Pb, ²⁰⁷Pb, ²⁰⁸Pb and ²⁰⁹Bi were monitored. Results of Pb, Cd, Cu, Zn, Mo and Co determination were in good agreement with certified values. In order to obtain accurate results for As at low levels, it was necessary to mathematically correct the analytical signal. This correction effectively eliminates the influence of interfering ArCl⁺ ions. For Cr analysis it is advisable to use as powerful oxidizing conditions during sample decomposition as possible.     

The role of different soil sample digestion methods on trace elements analysis: a comparison of ICP-MS and INAA measurement results

The measurement of trace-element concentration in soil, sediment and waste, is generally a combination of a digestion procedure for dissolution of elements and a subsequent measurement of the dissolved elements. “Partial” and “total” digestion methods can be used in environmental monitoring activities. To compare measurement results obtained by different methods, it is crucial to determine and to maintain control of the bias of the results obtained by these methods. In this paper, ICP-MS results obtained after matrix digestion with modified aqua regia (HCl+HNO₃+H₂O₂) method and two “total” digestion methods (microwave aqua regia+HF and HNO₃+HF) are compared with those obtained by instrumental neutron activation analysis, a non-destructive analytical method for the determination of the total mass concentrations of inorganic components in environmental matrices. The comparison was carried out on eight agricultural soil samples collected in one test area and measured by k₀-INAA and ICP-MS to determine As, Co, Cr, Sb and Zn mass concentration. The bias of results for As, Cd, Co, Cr, Cu, Ni, Pb, Sb and Zn of the three digestion methods were assessed using selected measurement standards. This paper highlights that the digestion procedure is an integral part of the measurement and can affect the measurement result in environmental analysis.     

Comparative study of different digestion procedures using supplementary analytical methods for multielement-screening of more than 50 elements in sediments of the river Elbe

The suitability of four different digestion procedures, i.e. i.) an aqua regia digestion according to DIN 38 414-S7, ii.) a pressure digestion using HNO₃/HF in PTFE-vessels, iii.) a HNO₃/HF + HCl-pressure digestion in PTFE-vessels and iv.) a HNO₃/HF + HCl-pressure digestion using microwave induction, has been evaluated with regard to the quantitative determination of about 50 elements in environmental samples. Three sediments of the river Elbe and two standard reference materials (MESS-1 and NIST 1645) have been employed. The analytical results from the dissolved samples, obtained using inductively coupled plasma mass- and optical emission spectrometry as well as total reflection X-ray fluorescence spectrometry, have been compared with those obtained by instrumental neutron activation analysis. Only digestion procedures using HNO₃/HF with a subsequent evaporation to dryness and dissolution in HCl have led to appropriate results for a wide range of elements (more than 50 elements in total). Because of its low contamination risk and its time saving, the microwave digestion is preferred. For this digestion procedure the accordance among the different instrumental methods used is high (better than 15% deviation) in general. A few elements (16) could be determined quantitatively only by a single method.     

Determination of metal concentrations in lichen samples by inductively coupled plasma atomic emission spectroscopy technique after applying different digestion procedures

Three digestion procedures have been tested on lichen samples for application in the determination of major, minor and trace elements (Al, Ca, Cd, Cr, Cu, Fe, K, Mg, Mn, Na, Ni, Pb, V and Zn) in lichen samples collected in Aegean Region of Turkey by inductively coupled plasma atomic emission spectrometer (ICP-AES). The acid mixture of concentrated HNO₃, H₂O₂ and HF were used. The instrument was optimized using lichen matrix considering RF power, nebulizer pressure, auxiliary flow rate and pump rate. The accuracy of the overall analyses was first estimated by analysis of two certified reference materials. Good agreement between measured and reference values were found for almost all elements. As the second way of determining the accuracy, results obtained from independent analytical techniques (ICP-AES and instrumental neutron activation analysis (INAA)) were compared for all elements by analyzing real samples. Correlation coefficients of two techniques for the elements ranged between 0.70 (Mg) and 0.96 (Fe). Among the three digestion systems, namely microwave, open vessel and acid bomb, microwave digestion system gave the best recovery results. The method detection limit (MDL) was computed using reagent blanks of microwave digestion system since it provides cleaner sample preparation. Detection limit is adequate for all elements to determine the elements in lichen samples. The precision was assessed from the replicate analyses of reagent blanks of microwave digestion system and was found to be less than 1.5% relative standard deviation (R.S.D.).     

ETAAS determination of Cd and Pb in plants

Simple and rapid analytical procedures for the ETAAS determination of Cd and Pb in plant (poplar, clover, plantain) leaves are described. Optimal conditions are presented for the wet digestion of plant matrices with a mixture of nitric acid and hydrogen peroxide along with optimal temperature programmes for subsequent modifier-free electrothermal determination of Cd and Pb. Slurry preparation procedures using tetramethylammonium hydroxide or a mixture of 1 mol/L HNO₃ + 1.5 mol/L H₂O₂ are proposed as another approach for rapid and accurate routine analysis of Cd and Pb in plant leaves. It has been found that single standard addition can be used for quantitative determination in the case of wet digestion ETAAS and standard addition to each analysed matrix is recommended in the case of slurry ETAAS. For all plant leaves investigated good agreement was achieved between the concentrations determined by wet digestion ETAAS and slurry ETAAS. The wet digestion method provides relative standard deviations for Cd ranging from 3% to 17% and for Pb from 2% to 16%. For the slurry method the RSD values are in the range of 4–31% for Cd and 4–30% for Pb, depending for both cases on the magnitude of the measured concentrations. Validity and versatility of the methods are verified by the analyses of standard reference materials. Received: 17 March 1997 / Revised: 2 May 1997 / Accepted: 8 May 1997     

Comparison of open digestion methods and selection of internal standards for the determination of Rh,Pd and Pt in plant samples by ICP-MS

An analytical procedure for the reliable determination of Pd, Pt and Rh in plant samples by inductively coupled plasma-mass spectrometry (ICP-MS) was developed. An ultrasonic nebulizer (USN) was used for sample introduction to improve sensitivity. Under various synthetic plant sample matrix compositions, it was established experimentally that moderate amounts (0.2–2%) of dissolved solids decreased the analyte signals significantly. Internal standardisation with In (for Pd and Rh) and Ir (for Pt) proved to be essential for obtaining correct results. Five open digestion approaches, used for converting solid plant samples to aqueous solution, were also tested for the purpose, namely dry-ashing, dry-ashing followed by HF attack, wet digestion with H₂O₂–HNO₃, wet digestion followed by HF attack and aqua regia digestion. Recovery tests in two spiked plant materials showed that only wet digestions must be used. With these ways, all PGEs could be reliably quantified by USN-ICP-MS without applying a separation or preconcentration step with a good precision (below 10% RSD). The aqua regia procedure was applied to the determination of PGEs in various plant matrices collected along a highway. Results showed that mosses were probably the best choice of samples to monitor the bioaccumulation of PGEs in time.     

Optimization of sample preparation and ICP-MS analysis for determination of 60 elements for characterization of the plant ionome

An ICP-MS method for determination of 60 elements in plant samples is proposed based on optimization of digestion, recommending use of HF besides HNO₃ and H₂O₂ and calibration procedures, using CRMs for construction of calibration curves. Adequate choice of analytical isotopes and various measurement conditions (cold plasma for the determination of Al, Ba, Ca, Fe, K, Mg, Mn, Na, Si and Sr and DRC mode for determination of Ag, As, Ni, Pd, Pt, Se and V) as well as introduction of appropriate corrections lead to determination of as large number of elements with quadropole ICP-MS as with the more expensive SF-ICP-MS. Two measurements are performed: cold plasma and standard/DRC mode. The analytical characteristics of the method are demonstrated by analysis of five CRMs and the agreement of the experimental results with the certified/information/literature values is very good. Detection limits are low enough to permit the determination of all elements but platinum metals at background level. The applicability of the method is demonstrated by analysis of Taraxacum officinale (dandelion) samples collected from regions with different anthropogenic influence. The results indicate high degree of pollution round the Pb-Zn smelter with As, Cd, Cu, Ni, Pb and Zn and increased concentrations of B, Be, Bi, Hg, In, Mn, Sb, Se, Sn, Ti, Tl, V and Zr. The dandelion sample, collected along a highway has increased concentrations of traffic released elements: Pt, Pd, Rh, Ce, La, Pb as well as Cu, Zn, Ba and Rb.     

Voltammetric Determination of Platinum in Plant Material

A very sensitive procedure for the determination of platinum in hydroponically cultivated plant samples (Sinapis alba L and Lolium perenne) is presented. A microwave digestion with HNO₃, HClO₄ and HCl acids with additional UV irradiation is followed by the platinum determination by adsorptive stripping voltammetry at hanging mercury drop electrode. The influence of HNO₃ acid on voltammetric determination of platinum is discussed. For validation of the obtained results the recovery of Pt was examined and the Pt determination by ICP MS was carried out. The highest platinum amounts were found in the roots of the plants, nevertheless the effective transport of platinum to the steams and leaves was also observed.     

Determination of total mercury in environmental and biological samples using k0-INAA, RNAA and CVAAS/AFS techniques: Advantages and disadvantages

The accuracy and precision of the results obtained for total mercury in various environmental and biological samples and certified reference materials (CRMs) by various analytical methods, including k ₀-instrumental neutron activation analysis (k ₀-INAA), radiochemical neutron activation analysis (RNAA) and cold vapour atomic absorption (and atomic fluorescence) spectrometry (CVAAS/AFS) used in routine analysis in our laboratory, were investigated. Three natural matrix reference materials (RMs) from the International Atomic Energy Agency (IAEA), five CRMs from the Institute for Reference Materials and Measurements (IRMM), six CRMs from the National Institute of Standards and Technology (NIST) and one from the Jožef Stefan Institute (IJS) were analyzed. The results obtained show good agreement between certified or assigned values, and between the methods used, except for some data obtained by k ₀-INAA in biological samples. This can be explained by losses during irradiation in semi-open systems (irradiation in plastic ampoules) and/or spectral interferences. This revised version was published online in August 2006 with corrections to the Cover Date.     

Multivariate technique for optimization of digestion procedure by focussed microwave system for determination of Mn, Zn and Fe in food samples using FAAS

This article describes the development by response surface methodology (RSM) of a procedure for iron, zinc and manganese determination by flame atomic absorption spectrometry (FAAS) in food samples after digestion employing a focussed microwave system. A Doehlert matrix was used to find optimal conditions for the procedure through response surface study. Three variables (irradiation power and time and composition of oxidant solution—HNO₃ + H₂O₂) were regarded as factors in the optimization study. The working conditions were established as a compromise between optimum values found for each analyte taking into consideration the robustness of the procedure. These values were 12 min, 260 W and 42% (v/v) for irradiation time, irradiation power and percent of H₂O₂ in solution, respectively. The accuracy of the optimized procedure was evaluated by analysis of certified reference materials and by comparison with a well-established closed vessel microwave dissolution methodology.     

Cyclic neutron activation analysis for determination of selenium in food samples using <Superscript>77m</Superscript>Se

Cyclic neutron activation analysis method was conducted for determination of Se in food samples. High accuracy and good precision were proved by analyzing certified reference materials (CRMs) of chicken (GBW10018), rice (GBW10010) and cabbage (GBW10014). The detection limits for the three CRMs reached 0.16, 0.66 and 1.2 ng after 6 cycles at the 161.9 keV γ-peak from ^77mSe, under a neutron flux of 9.0 × 10¹¹ n cm⁻² s⁻¹ and the conditions of 30 s irradiation, 2 s decay, 30 s counting and 2 s waiting, significantly lower than those of conventional neutron activation analysis without any cycles, which were 0.94, 3.6 and 4.3 ng, respectively.     

Microwave enhanced alkaline digestion of silicate samples for determination of Fe2O3

A novel approach to the study of microwave enhanced alkaline digestion was developed for rapid digestion of silicate samples. By using alkali metal hydroxide solution as microwave digestion solvent, the feasibility and principle of digestion were discussed for the determination of Fe₂O₃ contents in quartz, kaolin, feldspar and soda-lime-silica glass. The results obtained from four standard samples and six real world samples are in good agreement with the certified values, and are comparable to the predicted results from traditional alkaline digestion method. All the above demonstrates that this new proposed method is precise, accurate and can provide a simple, fast and energy saving procedure for the determination of components in silicate samples.     

Determination of mercury and selenium in consumed food items in Libya using instrumental and radiochemical NAA

Summary Instrumental and radiochemical neutron activation analysis (INAA and RNAA, respectively) were used to analyze several consumed food items in Libya for the detection of low level concentrations of mercury and selenium. Selenium was determined using both short- and long-term irradiation, while mercury was determined in the long-term irradiation mode. At RNAA, after wet-ashing of samples in a microwave digestion unit, mercury was extracted with Ni(DDC)₃/CHCl₃, and selenium was precipitated in elemental form with ascorbic acid. For quality control, NIST reference materials were analyzed using the same procedures as for the food samples. The results of the analytical modes used were compared.     

Rapid dissolution of large environmental samples for the determination of fission products

The dissolution of large environmental samples was investigated using a microwave autoclave, capable of digestion conditions of 300 °C and 200 bar, for the application of rapid determination of radionuclides. Six samples of up to 5 g plant material were digested, also eliminating predigestion steps such as ashing and grinding. Batches of forty 1 g samples of plant leaves were also completely digested in 75 minutes. Quantitative recovery of ⁹⁰Sr from 5 g soil samples by leaching with 8M HNO₃ at 200 °C was achieved, whereas ¹³⁷Cs was not completely recovered from the large soil samples using total digestion or leaching (HCl:HNO₃) techniques, but quantitative recovery was achieved using fusion and sinter procedures.     

Instrumental neutron activation analysis of sediment reference materials using the k0-standardization method

An instrumental neutron activation analysis technique has been developed for the determination of As, Au, Ba, Co, Cr, Fe, Hf, Sb, Ta, Th, U, W and Zn in large (10–15 g) geological samples using in-pool irradiation with a SLOWPOKE-2 reactor. The technique allows for the simultaneous irradiation of multiple samples using a neutron flux of between 4·10¹³ and 8·10¹³ n·m^–2·s^–1. The detection limits obtained using the analytical methodology described in this paper are acceptable for exploration geochemistry and the technique has been used to analyze samples collected as part of a metallic minerals survey of Jamaica.     

Multiple small volume microwave-assisted digestions using conventional equipment for multielemental analysis of human breast biopsies by inductively coupled plasma optical emission spectrometry

A multiple microwave-assisted digestion procedure using small PTFE closed vials (6 mL capacity) inserted into conventional microwave digestion vessels has been developed as a fast, efficient and clean methodology for multielemental analysis of human breast biopsies by inductively coupled plasma optical emission spectrometry. This small volume strategy allows drastically diminishing the volume of acid needed for digestion, and in turn, a decrease in sample dilution and an increase in sample throughput is achieved. A 2_IV^4-1 fractional factorial design was used for screening optimization of four variables that can influence the digestion efficiency: (A) nitric acid volume, (B) pre-digestion step, (C) microwave power, and (D) digestion time. A validation study included linearity, precision, detection and quantification limits. Validation against different biological certified reference materials (CRMs) was also performed.The digestion method is suitable for the determination of Al, Ca, Cu, Fe, K, Mg, Mn, P, S and Zn in small size biological samples such as breast biopsies (<30 mg dry mass). Forty-seven biopsies from 39 women were analyzed: 20 samples from healthy women corresponding to mammoplasties and 27 samples from patients suffering from cancer pathology (19 corresponded to tumour and 8 to adjacent normal tissue). A significant accumulation of Al, Ca, Cu, K, Mg, Mn, P and Zn was found in tumour as compared to healthy tissues. When this comparison is made for tumour and adjacent tissues, a significant accumulation of Al, Mg, P and Zn in tumour tissues was observed. Finally, only Ca significantly accumulates in the adjacent tissues as compared to healthy tissues.     

Optimised method of coal digestion for trace metal determination by atomic absorption spectroscopy

Understanding the transport of trace elements through a coal-fired power plant requires reliable analytical methods for these elements in all the ingoing and outgoing mass streams. Coal and different kinds of ashes comprise the most abundant mass streams in such a plant. As a continuation of our previous work, we have optimised a digestion method for the AAS determination of heavy metals in coal samples. It has become evident that complete dissolution of metals in coal samples and accurate results in subsequent analysis can be obtained by means of applying pressurised digestion under microwave heating. The combination of HNO₃ (conc.) and HF (conc.) in the volume ratio of 50?:?1 attacked the sample well enough, and good recoveries for all the metals studied were obtained. Surprisingly good results were obtained also when HNO₃ alone was used as the digestion acid.