首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 82 毫秒
1.
以草酸盐为前驱体采用两步法制备了一种以CaO-MgO作为活性组分,以CoFe_2O_4作为磁核的磁性固体碱催化剂,并用于大豆油与甲醇的酯交换反应合成生物柴油。对制备的磁性固体碱催化剂进行了磁滞回线、X-射线衍射(XRD)、CO_2-TPD及透射电镜(TEM)表征。考察了不同核壳物质的量比、焙烧温度、反应温度、反应时间、醇油物质的量比以及催化剂用量等因素对大豆油转化为生物柴油产率的影响。结果表明,采用核壳物质的量比为1∶6、焙烧温度为700℃所制备的CaO-MgO@CoFe_2O_4催化剂,当醇油物质的量比为12、催化剂用量为大豆油质量的1.0%时,在65℃下反应时间3 h,生物柴油收率高达97.1%。该催化剂具有较好的重复利用性能,重复利用四次后生物柴油的收率仍可达90%。  相似文献   

2.
桦甸页岩油柴油馏分加氢精制生产清洁燃料油的研究   总被引:3,自引:0,他引:3  
柴油馏分(200℃~360℃)在桦甸页岩油中约占41%。其中,硫、氮及不饱和烃含量较高,含硫化合物以苯并噻吩类及二苯并噻吩类化合物为主,而氮化物中的碱性氮化物和非碱性氮化物的含量相当。实验中分别以硫化态的CoMo/Al2O3及NiW/Al2O3为催化剂,利用固定床小型加氢反应装置,考察了不同工艺条件对桦甸页岩油柴油馏分加氢脱硫及加氢脱氮效果的影响。结果表明,反应温度升高,增大反应压力,降低体积空速,对脱硫、脱氮都是有利的,特别是对加氢脱氮影响最为明显,而氢油体积比的影响相对较小。两种催化剂活性比较发现,对于该页岩馏分油而言,两种催化剂的加氢脱硫效果相差不大,而NiW/Al2O3的加氢脱氮效果却明显好于CoMo/Al2O3。在选择的工艺条件下,对桦甸页岩油柴油馏分进行加氢精制得到的产品油中杂原子和不饱和烃含量低,密度小,芳香烃含量少,可作为优质清洁柴油直接使用。  相似文献   

3.
采用浸渍法,将硫物种直接负载于氧化锆晶体载体表面,经一步焙烧制备了硫化氧化锆催化剂复合材料。采用X-射线衍射(XRD)和傅里叶红外(FT-IR)分别对催化剂的晶相结构和表面基团进行了表征。结果表明:催化剂均呈现出有利于酯交换反应的纯四方相结构,催化剂表面形成了硫物种活性中心。考察了焙烧时间、反应温度、反应时间等生物柴油工艺条件对产物收率的影响规律。研究表明:工艺条件改变均对生物柴油的收率产生影响,其中调变催化反应温度对生物柴油的收率影响程度最为显著,而增加焙烧时间、降低反应温度、缩短反应时间均使得生物柴油的收率下降,其中在焙烧时间为1 h、反应温度为150 ℃及反应时间为6 h的优化合成条件下可获得的脂肪酸甲酯收率高达97.8%。  相似文献   

4.
采用浸渍法将活性氧化钙颗粒负载在介孔二氧化硅(KIT-6)表面,制备了酯交换反应催化剂CaO/KIT-6,并研究了其在大豆油与甲醇酯交换制备生物柴油反应中的催化性能。通过X射线衍射(XRD)、X射线光电子能谱(XPS)、CO_2程序升温脱附(CO_2-TPD)等测试手段对催化剂进行表征。在酯交换反应中,当醇油物质的量比为12、反应温度为65°C、催化剂用量为8%、Ca/Si原子比为0.4、反应时间为2 h时,生物柴油转化率达到99.9%,CaO/KIT-6重复使用五次后催化活性仍保持在90%以上。与CaO及其他负载型催化剂相比,CaO/KIT-6催化剂在较低醇油物质的量之比、较短反应时间展现出更高的催化性能和良好的重复使用性。  相似文献   

5.
钙基负载型固体碱催化酯交换反应活性评价   总被引:4,自引:0,他引:4  
动植物油脂与醇通过酯交换反应制备生物柴油,目前,工业上一般采用NaOH、KOH、NaOCH,等均相催化剂。均相催化剂的缺点是产品后处理复杂,产生大量含碱含油工业废水。而非均相固体碱催化酯交换反应,产品与催化剂分离容易,产品不需要水洗,避免了大量废液的排放。采用非均相固体碱制备生物柴油的文献报道较多,但固体碱的碱中心数、碱中心强度对酯交换反应影响的报道较少。本研究制备了钙基负载型固体碱催化剂,重点研究钙基负载型固体碱的制备工艺条件对碱强度、碱量分布的影响,考察碱强度、碱量分布对催化菜籽油与甲醇的酯交换反应制备生物柴油转化率的影响。  相似文献   

6.
双核碱性离子液体催化棉籽油酯交换制备生物柴油   总被引:14,自引:2,他引:12  
采用两步法制备了五种新型咪唑类碱性双核功能化离子液体化合物,并考察了对棉籽油酯交换制备生物柴油的催化性能。结果表明,咪唑类碱性双核功能化离子液体具有很好的催化活性,其催化活性与阳离子中碳链长度有关。其中,双-(3-甲基-1-咪唑)亚乙基双氢氧化物离子液体的催化活性最好。催化剂量、反应时间、反应温度及醇油比对生物柴油中脂肪酸甲酯含量及选择性影响的研究发现,在催化剂用量为0.4%(质量分数),醇油摩尔比为12,反应温度为55℃,反应时间为4 h时,脂肪酸甲酯的含量和选择性分别达98.5%和99.9%。催化剂7次循环后,产物中脂肪酸甲酯含量仍达到96.2%,单甘酯和双甘酯的含量很少,表明该催化剂重复使用良好。  相似文献   

7.
采用溶胶-凝胶法合成Ca O@Si O_2固体碱催化剂,以聚苯乙烯有机聚合物为硬模板剂和以P123为软模板剂对Ca O的微观形貌进行调控。并将其应用于大豆油与甲醇的酯交换制备生物柴油的反应体系中。通过对Ca O@Si O_2纳米固体碱催化剂进行X射线衍射(XRD)、扫描电子显微镜(SEM)、透射电镜(TEM)、CO_2-TPD及N_2的吸附-脱附(BET)表征发现,不仅制备得到了形貌归整的纳米固体颗粒,而且得到了Ca O包裹在Si O_2表面的核壳结构。进一步考察了不同的硅钙质量比、反应温度、催化剂的用量以及油醇物质的量比对生物柴油收率的影响,生物柴油的收率最高可以达到95.6%。  相似文献   

8.
该大学生创新研究项目以清洁能源为切入点,借助绿色催化剂离子液体催化制备生物柴油。在制备双功能Brönsted酸性离子液体[PSMIM]HSO4的基础上,以多孔氧化硅为载体,采用物理负载法制备固载型催化剂[PSMIM]HSO4/SiO2。并以此为催化剂催化葵花油制备生物柴油,探讨催化剂用量、反应时间、醇油比和反应温度对生物柴油产率的影响。结果表明:醇油比为25:1、催化剂用量为8%、反应温度为160℃、时间为10 h的条件下,生物柴油的转化率达到92.5%。采用FTIR、13C NMR、XRD对催化剂结构进行表征;采用GC-2010气相色谱对生物柴油进行组分分析;并对其密度、运动黏度、凝点等理化性能进行了测定。结果表明所制得的生物柴油基本符合我国生物柴油的标准。本项目的开展不仅在研究成果方面取得了一定的成绩,同时也使学生的创新意识和团队意识,以及教师的教学能力得到提升。  相似文献   

9.
酸性离子液体催化脂肪酸甲酯聚合制备二聚酸甲酯   总被引:1,自引:0,他引:1  
 以 Brönsted-Lewis 酸性离子液体为催化剂, 用于催化生物柴油中不饱和脂肪酸甲酯聚合制备二聚酸甲酯反应, 考察了催化剂种类、催化剂用量、反应温度和时间等因素对聚合反应性能的影响, 得到较佳的反应条件. 结果表明, 当以 1-(3-磺酸)-丙基-3-甲基咪唑氯锌酸盐[HO3S-(CH2)3-mim]Cl-ZnCl2 (ZnCl2 摩尔分数为 0.67) 为催化剂, 生物柴油 15 g, m(生物柴油):m(离子液体) = 15:1, 于 240 oC 下反应 6 h 时, 二聚酸甲酯收率为 63.2%, 其中三聚体含量小于 5%. 另外, 该催化剂重复使用 5 次后, 二聚酸甲酯收率仍超过 63%, 表明其具有较好的重复使用性能. 离子液体的 Brönsted 和 Lewis 酸位的协同效应显著提高了其催化活性.  相似文献   

10.
将强酸性阳离子交换树脂加入塔尔油脂肪酸和甲醇混合液中,并在超声波辐射辅助下得到生物柴油,对生物柴油的制备工艺和性能进行研究,同时建立动力学模型。结果表明,超声波辐射的辅助强化,能有效提高生物柴油的得率;在反应温度65℃、反应时间1h、甲醇与TOFA摩尔比为10∶1、脱水剂用量为TOFA6%、树脂NKC-9用量为TOFA40%的最佳工艺条件下,反应平衡常数可达11.18,生物柴油得率为90.0%。建立的动力学模型补充了超声波辐射辅助酯化反应动力学参数,并用此模型解释了各工艺参数呈现的规律。以廉价的制浆黑液回收物塔尔油脂肪酸为原料制备生物柴油,能有效地降低生物柴油价格,提高其市场竞争力,实现塔尔油高附加值利用,具有良好的发展前景。  相似文献   

11.
The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.  相似文献   

12.
非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。  相似文献   

13.
翟宗玺  刘树深  夏树屏 《化学学报》1990,48(10):946-950
用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。  相似文献   

14.

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

  相似文献   

15.
Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.  相似文献   

16.
Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.  相似文献   

17.
In this review, the research of the author in the field of colloidal systems is summarized. The factors influencing colloidal stability are systematized and analyzed. Examples are presented to illustrate the practical utilization of the theory of stability of colloids and thin films.This review was prepared on the basis of the works of the author, which were awarded the State Premium for 1991 in the field of science and technology, chemistry section.Institute of Physical Chemistry, Russian Academy of Sciences, 117915 Moscow. Translated from Izvestiya Akademii Nauk, Seriya Khimicheskaya, No. 8, pp. 1708–1717, August, 1992.  相似文献   

18.
Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, Mo, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.  相似文献   

19.
20.
The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe2O3. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号