Magnesium ion-conducting gel polymer electrolytes dispersed with fumed silica for rechargeable magnesium battery application

Effect of fumed silica dispersion on poly(vinylidene fluoride-co-hexafluoropropylene)-based magnesium ion-conducting gel polymer electrolyte has been studied using various physical and electrochemical techniques. The composite gel electrolytes are free-standing and flexible films with enough mechanical strength. The optimized composition with 3 wt.% filler offers a maximum ionic conductivity of ∼1.1 × 10⁻² S cm⁻¹ at ∼25 °C with good thermal and electrochemical stabilities. The Mg²⁺ ion conduction in the gel nanocomposite film is confirmed from the cyclic voltammetry, impedance spectroscopy, and transport number measurements. The space-charge layers formed between filler particles and gel electrolyte are responsible for the enhancement in ionic conductivity. The applicability of the gel nanocomposite to a rechargeable battery is examined by fabricating a prototype cell consisting of Mg [or Mg-multiwalled carbon nanotube (MWCNT) composite] and MoO₃ as negative and positive electrodes, respectively. The discharge capacity and the rechargeability of the cell have been improved when Mg metal is substituted by Mg-MWCNT composite. The discharge capacity of the optimized cell has found to be ∼175 mAh g⁻¹ of MoO₃ for an initial ten charge–discharge cycles.     

Cross-linking copolymers of acrylates’ gel electrolytes with high conductivity for lithium-ion batteries

The cross-linking gel copolymer electrolytes containing alkyl acrylates, triethylene glycol dimethacrylate, and liquid electrolyte were prepared by in situ thermal polymerization. The gel polymer electrolytes containing 15 wt% polymer content and 85 wt% liquid electrolyte content with sufficient mechanical strength showed the high ionic conductivity around 5?×?10^?3 Scm^?1 at room temperature. The gel electrolytes containing different polymer matrices were prepared, and their physical observation and conductivity were discussed carefully. The cross-linking copolymer gel electrolytes of alkyl acrylates with other monomers were designed and synthesized. The results showed that copolymerization can improve the mechanical properties and ionic conductivities of the gel electrolytes. The polymer matrices of gels had excellent thermal stability and electrochemical stability. The scanning electron microscope analysis showed the gel electrolyte was the homogeneous structure, and the cross-linking polymer host was the porous three-dimensional network structure, which demonstrated the high conductivity of the gel electrolytes. The gel polymer Li-ion battery was prepared by this in situ thermal polymerization. The cell exhibited high charge-discharge efficiency at 0.1 C. The results of LiFePO4-PEA-Li cell and graphite-PEA-Li cell showed that gel polymer electrolytes have good compatibility with the battery electrodes materials.     

高锂离子电导的有机-无机复合电解质的渗流结构设计

固态聚合物电解质被认为是解决传统液态锂金属电池安全隐患和循环性能的关键材料,但仍然存在离子电导率低,界面兼容性差等问题。近年来,基于无机填料与聚合物电解质的高锂离子电导的有机-无机复合电解质备受关注。根据渗流理论,有机-无机界面被认为是复合电解质离子电导率改善的主要原因。因此,设计与优化有机-无机渗流界面对提高复合电解质离子电导率具有重要意义。本文从渗流结构的设计出发,综述了不同维度结构的无机填料用于高锂离子电导的有机-无机复合电解质的研究进展,并对比分析了不同渗流结构的优缺点。基于上述评述,展望了有机-无机复合电解质的未来发展趋势和方向。     

介孔材料SBA-15改性的复合凝胶聚合物电解质的制备及性能

以聚(甲基丙烯酸甲酯-聚乙二醇二甲基丙烯酸酯)(P(MMA-PEGDMA))共聚物为基体,介孔硅分子筛SBA-15为无机填料制备了复合凝胶聚合物电解质.采用原子力显微镜(AFM)、热重分析(TG)和交流阻抗(AC)等技术对其形貌、热稳定性及电化学性能进行了研究.结果表明:无机填料SBA-15与聚合物基体有较好的相容性;SBA-15的加入改善了聚合物电解质的热稳定性,提高了离子电导率,当W(SBA-15)=0.03时,离子电导率达最大值3.68×lO-3S/cm;并且掺杂SBA-15后,聚合物电解质的电化学稳定性得到了提高,其电化学稳定窗口为4.9V(vs Li /Li),可满足高性能锂离子电池的要求.     

Ionic transport in P(VDF-HFP)-PMMA-LiCF3SO3-(PC + DEC)-SiO2 composite gel polymer electrolyte

Composite gel polymer electrolytes composed of poly(vinylidene fluoride-co-hexafluoropropylene) P(VDF-HFP) and polymethylmethacrylate PMMA polymers, PC + DEC as plasticizer and LiCF₃SO₃ as salt and fumed silica as filler have been synthesized by solvent casting technique with varying plasticizer-filler ratio systematically. Films of thickness in the range of 40-70 μm were characterized by a.c. impedance measurements in the temperature range 303 K to 373 K. Addition of filler to the polymer electrolyte was found to result in an enhancement of the ionic conductivity. A maximum electrical conductivity of ∼1 × 10⁻³ S/cm at 303 K and ∼2.1 × 10⁻³ S/cm at 373 K has been achieved with the dispersion of the SiO₂. FTIR spectral studies confirmed the polymer-salt interaction. XRD patterns exhibit the increased amorphicity in the blended composite gel polymer electrolytes. Scanning electron micrograph shows the dispersion of SiO₂ particle in the polymer electrolyte.     

The network gel polymer electrolyte based on poly(acrylate-co-imide) and its transport properties in lithium ion batteries

Poly (acrylate-co-imide)-based gel polymer electrolytes are synthesized by in situ free radical polymerization. Infrared spectroscopy confirms the complete polymerization of gel polymer electrolytes. The ionic conductivity of gel polymer electrolytes are measured as a function of different repeating EO units of polyacrylates. An optimal ionic conductivity of the poly (PEGMEMA₁₁₀₀-BMI) gel polymer electrolyte is determined to be 4.8 × 10^–3 S/cm at 25 °C. The lithium transference number is found to be 0.29. The cyclic voltammogram shows that the wide electrochemical stability window of the gel polymer electrolyte varies from −0.5 to 4.20 V (vs. Li/Li⁺). Furthermore, we found the transport properties of novel gel polymer electrolytes are dependent on the EO design and are also related to the rate capability and the cycling ability of lithium polymer batteries. The relationship between polymer electrolyte design, lithium transport properties and battery performance are investigated in this research.     

Composite gel membranes: a new class of improved polymer electrolytes for lithium batteries

Novel composite, gel-type polymer electrolytes have been prepared by dispersing selected ceramic powders into a matrix formed by a lithium salt solution contained in a poly(acrylonitrile) (PAN) network. The electrochemical characterization demonstrates that these new types of composite gel electrolytes have high ionic conductivity, wide electrochemical stability and, particularly, high chemical integrity (no liquid leakage) even at temperatures above ambient. These unique properties make the composite gel membranes particularly suitable as electrolyte separators in lithium ion polymer batteries.     

Fabrication and characterization of P(VDF-HFP)/SBA-15 composite membranes for Li-ion batteries

This study reports on the preparation of a composite polymer electrolyte for secondary lithium-ion battery. Poly(vinylidiene fluoride-hexafluoropropylene) (P(VDF-HFP)) was used as the polymer host, and mesoporous SBA-15 (silica) ceramic fillers used as the solid plasticizer were added into the polymer matrix. The SBA-15 fillers with mesoporous structure and high specific surface can trap more liquid electrolytes to enhance the ionic conductivity. The ionic conductivity of P(VDF-HFP)/SBA-15 composite polymer electrolytes was in the order of 10⁻³ S cm⁻¹ at room temperature. The characteristic properties of the composite polymer membranes were examined by using FTIR spectroscopies, scanning electron microscopy (SEM), and an AC impedance method. For comparison, the LiFePO₄/Li composite batteries with a conventional microporous polyethylene (PE) separator and pure P(VDF-HFP) polymer membrane were also prepared and studied. As a result, the LiFePO₄/Li composite battery comprised the P(VDF-HFP)/10 wt.% m-SBA-15 composite polymer electrolyte, which achieves an optimal discharge capacity of 88 mAh g⁻¹ at 20 C rate with a high coulomb efficiency of 95%. It is demonstrated that the P(VDF-HFP)/m-SBA-15 composite membrane exhibits as a good candidate for application to LiFePO₄ polymer batteries.     

Ionic liquid‐based organic–inorganic hybrid electrolytes: Impact of in situ obtained and dispersed silica

Organic–inorganic hybrid electrolytes based on PEO‐NaTFSI‐ionic liquid (HMIMTFSI)‐silica (in situ production via sol gel process) are being reported in this article. The variation in conductivity with ionic liquid (IL) addition has been explained on the basis of number of free TFSI anions evaluated using ATR‐IR data. The deconvolution of the IR spectra of these hybrid electrolytes has given evidence of ion‐pair formation which has been compared vis‐á‐vis the conductivity variation. The hybrid electrolyte with maximum conductivity comprises the highest number of free imide ions and has lowest glass transition temperature. FESEM has displayed a porous and layered surface morphology with dispersed silica nanoparticles. In addition, the optimized hybrid electrolyte has been compared with 5 wt% (limit of mechanical stability) ex situ silica added composite where the temperature cycling of conductivity has shown that the ex situ dispersed hybrid electrolytes do not retrace their conductivity path contrary to the in situ prepared hybrid electrolytes. This behavior has been explained to be due to the hindrance offered by the ex situ added silica in the recrystallization kinetics of PEO. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 207–218     

Improving the performance of all-solid-state supercapacitors by modifying ionic liquid gel electrolytes with graphene nanosheets prepared by arc-discharge

Ionic liquid gel polymers have widely been used as the electrolytes in all-solid-state supercapacitors, but they suffer from low ionic conductivity and poor electrochemical performance. Arc discharge is a fast, low-cost and scalable method to prepare multi-layered graphene nanosheets, and as-made graphene nanosheets （denoted as ad-GNSs） with few defects, high electrical conductivity and high thermal stability should be favorable conductive additive materials. Here, a novel ionic liquid gel polymer electrolyte based on an ionic liquid （EM1MNTF2） and an copolymer （P（VDF-HFP）） was modified by the addition of ad-GNSs as an ionic conducting promoter. This modified gel electrolyte shows excellent thermal stability up to 400 ℃ and a wide electrochemical window of 3 V. An all-solid-state supercapacitor based on commercial activated carbon was fabricated using this modified ionic liquid gel polymer electrolyte, which shows obviously improved electrochemical behaviors compared with those of the corresponding all-solid-state supercapacitor using pure ionic liquid gel polymer electrolyte. Specially, smaller internal resistance, higher specific capacitance, better rate performance and cycling stability are achieved. These results indicate that the ionic liquid gel polymers modified by ad-GNSs would be promising and suitable gel electrolytes for high performance all-solid-state electrochemical devices.     

PEO/LiClO_4纳米SiO_2复合聚合物电解质的电化学研究

将实验室制备的纳米二氧化硅和市售纳米二氧化硅粉末与PEO LiClO4复合 ,制得了复合PEO电解质 .它们的室温离子电导率可比未复合的PEO电解质提高 1～ 2个数量级 ,最高可以达到 1 2 4× 10 - 5S cm .离子电导率的提高有两方面的原因 :一是无机二氧化硅粉末的加入抑制了PEO的结晶 ,是二氧化硅粉末和聚合物电解质之间形成的界面对电导率的提高也有一定的作用 .在进一步加入PC EC(碳酸丙烯酯 碳酸乙烯酯 )混合增塑剂后制得的复合凝胶PEO电解质 ,可使室温离子电导率再提高 2个数量 ,达到 2× 10 - 3 S cm .用这种复合凝胶PEO电解质组装了Li|compositegelelectrolyte|Li半电池 ,并测量了该半电池的交流阻抗谱图随组装后保持时间的变化 ,实验观察到在保持时间为 144h以内钝化膜的交流阻抗迅速增大 ,但在随后的时间内逐渐趋于平稳 ,表明二氧化硅粉末的加入可以有效地抑制钝化膜的生长     

Ion conducting properties of poly(ethylene oxide)-based electrolytes incorporating amorphous silica attached with imidazolium salts

Poly(ethylene oxide) (PEO)-based polymer electrolytes containing amorphous silica attached ionic liquid (IL) were studied in order to improve electrochemical and interfacial properties. An imidazolium salt such as IL was attached to modified ceramic fillers. The modified ceramic fillers were amorphous silica with the immobilized 1-methyl-3-propyl-imidazolium bromide (MPIm-AS). PEO-based polymer electrolytes were prepared by using the solution casting technique. In order to investigate the ionic conductivity, studies on the modified filler addition effects on the ion-conducting behavior of polymer electrolytes having specific amounts of MPIm-AS were carried out. The addition of MPIm-AS in polymer electrolytes has resulted in higher ionic conductivity at room temperature. The structure, crystallinity, and morphology of the solid polymer electrolytes were evaluated using X-ray diffraction, differential scanning calorimetry, and scanning electron microscope measurement. The ionic conductivity was measured by an AC impedance method. The enhanced conductivity was dependent on the decreased crystallinity and the changed morphologies of composites.     

染料敏化太阳电池用聚合物电解质

综述了本研究小组近年来用于染料敏化太阳电池中聚合物电解质的研究概况.设计合成了几类性能优良的聚合物电解质,较好地改进了液体电解质染料敏化太阳电池(DSSC)的使用稳定性,研究结果具有实际应用的价值,并提出了此领域研究今后的发展方向.     

Influence of barium titanate nanofiller on PEO/PVdF-HFP blend-based polymer electrolyte membrane for Li-battery applications

Organic-inorganic hybrid membranes based on poly(ethylene oxide) (PEO) 6.25 wt%/poly(vinylidene fluoride hexa fluoro propylene) [P(VdF-HFP)] 18.75 wt% were prepared by using various concentration of nanosized barium titanate (BaTiO₃) filler. Structural characterizations were made by X-ray diffraction and Fourier transform infrared spectroscopy, which indicate the inclusion of BaTiO₃ in to the polymer matrix. Addition of filler creates an effective route of polymer-filler interface and promotes the ionic conductivity of the membranes. From the ionic conductivity results, 6 wt% of BaTiO₃-incorporated composite polymer electrolyte (CPE) showed the highest ionic conductivity (6 × 10^?3 Scm^?1 at room temperature). It is found that the filler content above 6 wt% rendered the membranes less conducting. Morphological images reveal that the ceramic filler was embedded over the membrane. Thermogravimetric and differential thermal analysis (TG-DTA) of the CPE sample with 6 wt% of the BaTiO₃ shows high thermal stability. Electrochemical performance of the composite polymer electrolyte was studied in LiFePO₄/CPE/Li coin cell. Charge-discharge cycle has been performed for the film exhibiting higher conductivity. These properties of the nanocomposite electrolyte are suitable for Li-batteries.     

A novel composite polymer electrolyte containing room-temperature ionic liquids and heteropolyacids for dye-sensitized solar cells

A novel composite polymeric gel comprising room-temperature ionic liquids (1-butyl-3-methyl-imidazolium-hexafluorophosphate, BMImPF₆) and heteropolyacids (phosphotungstic acid, PWA) in poly(2-hydroxyethyl methacrylate) matrix was successfully prepared and employed as a quasi-solid state electrolyte in dye-sensitized solar cells (DSSCs). These composite polymer electrolytes offered specific benefits over the ionic liquids and heteropolyacids, which effectively enhanced the ionic conductivity of the composite polymer electrolyte. Unsealed devices employing the composite polymer electrolyte with the 3% content of PWA achieved the solar to electrical energy conversion efficiency of 1.68% under irradiation of 50 mW cm⁻² light intensity, increasing by a factor of more than three compared to a DSSC with the blank BMImPF₆-based polymer electrolyte without PWA. It is expected that these composite polymer electrolytes are an attractive alternative to previously reported hole transporting materials for the fabrication of the long-term stable quasi-solid state or solid state DSSCs.     

原位聚合制备的离子液体/聚合物电解质的研究

采用原位聚合制备出新型的BMIPF6/PMMA聚合物电解质透明弹性膜. 研究结果表明, BMIPF6/PMMA聚合物电解质体系在305 ℃时仍具有较好的热稳定性, 其安全性能优于含有机溶剂的传统非水电解质体系. 随着离子液体含量的增加, 其玻璃化转变温度逐渐减小, 离子电导率升高; 且离子电导率与温度的关系服从VTF方程. 其中, 当BMIPF6的质量分数为50%时, 该聚合物电解质的室温离子电导率高达0.15 mS/cm.     

Characterization and properties of ternary P(VdF-HFP)-LiTFSI-EMITFSI ionic liquid polymer electrolytes

Gel polymer electrolytes containing 1-ethyl-3-methylimidazolium-bis (trifluoromethyl-sulfnyl)imide (EMITFSI) ionic liquid were prepared for lithium ion batteries by solution casting method. Thermal and electrochemical properties have been determined for the gel polymer electrolytes. Proper addition of EMITFSI to the P(VdF-HFP)-LiTFSI polymer electrolyte improves the ionic conductivity and electrochemical window to 2.11 × 10⁻³ S cm⁻¹ (30 °C) and 4.6 V. In combination of the prepared ternary P(VdF-HFP)-LiTFSI-EMITFSI ionic liquid polymer electrolytes, Li₄Ti₅O₁₂ anode exhibited two extra voltage plateaus around 1.1 V and 2.3 V except the typical voltage plateau around 1.6 V by possible side reaction between ionic liquid and polymer. LiFePO₄ cathode exhibited high capacity above 140 mA h g⁻¹ and retention of 93.1% due to the suppressed polarization effect caused by enhanced ion transport properties. The high temperature of 80 °C didn't have significant impact on the cycling performance.     

High ionic conductivity of all-solid polymer electrolytes based on polyorganophosphazenes

A series of all-solid polymer electrolytes were prepared by cross-linking new designed poly(organophosphazene) macromonomers. The ionic conductivities of these all-solid, dimensional steady polymer electrolytes were reported. The temperature dependence of ionic conductivity of the all-solid polymer electrolytes suggested that the ionic transport is correlated with the segmental motion of the polymer. The relationship between lithium salts content and ionic conductivity was discussed and investigated by Infrared spectrum. Furthermore, the polarity of the host materials was thought to be a key to the ionic conductivity of polymer electrolyte. The all-solid polymer electrolytes based on these poly(organophosphazenes) showed ionic conductivity of 10⁻⁴ S cm⁻¹ at room temperature.     

Poly(vinylidene fluoride-hexafluoropropylene) (PVdF-HFP) based composite electrolytes for lithium batteries

The composite polymer electrolyte (CPE) membranes, comprising of poly(vinylidene fluoride-hexafluoropropylene) (PVdF-HFP), aluminum oxyhydroxide, (AlO[OH]_n) of two different particle sizes 7 μm/14 nm and LiN(CF₃SO₂)₂ as lithium salt were prepared using solution casting technique. The prepared membranes were subjected to XRD, impedance spectroscopy, compatibility and transport number studies. The incorporation of nanofiller greatly enhanced the ionic conductivity and the compatibility of the composite polymer electrolyte. Also LiCr_0.01Mn_1.99O₄/CPE/Li cells were assembled and their charge-discharge profiles have been made at 70 °C. The film which possesses nanosized filler offered better electrochemical properties than those with micron sized filler. The results are discussed based on Lewis acid-base theory.     

High ionic conductive PVDF-based fibrous electrolytes

The high ionic conductive polymer electrolytes were prepared based on poly(vinylidenefluoride) (PVDF) fibers modified via preirradiation grafting poly(methyl methacrylate) (PMMA). In these polymer electrolytes, the PVDF fibers served as the supporting phase providing dimensional stability, and PMMA acted as the gel phase helping for the trapping liquid electrolyte and substituting the nonconductive PVDF phase to provide contact with electrodes well thus increasing conductive area. The modified PVDF fibrous membranes were used as a polymer electrolyte in lithium ion battery after they were activated by uptaking 1 M LiPF₆/ethylene carbonate–dimethyl carbonate (1:1 vol) liquid electrolyte, which showed a much higher room-temperature ionic conductivity than the pristine PVDF fibrous membrane. The LiCoO₂-mesocarbon microbead coin cells containing the dual-phase fibrous membrane (degree of graft, 111.8%) demonstrated excellent rate performance, and the cell still retained about 86% of discharge capacity at 4C rate, as compared to that at 0.1C rate. The prototype cell showed good cycle performance.