Structure and properties of new polyester elastomers composed of poly(trimethylene terephthalate) and poly(ethylene oxide)

Series of PTT-b-PEO copolymers with different composition of rigid PTT and PEO flexible segments were synthesized from dimethyl terephthalate (DMT), 1,3-propanediol (PDO), poly(ethylene glycol) (PEG, M_n = 1000 g/mol) in a two stage process involving transesterification and polycondensation in the melt. The weight fraction of flexible segments was varied between 20 and 70 wt%. The molecular structure of synthesized copolymers was confirmed by ¹H NMR and ¹³C NMR spectroscopy. The superstructure of these polymers was characterized by DSC, DMTA, WAXS and SAXS measurements. It was observed that domains of three types can exist in PTT-b-PEOT copolymers: semi-crystalline PTT, amorphous PEO rich phase (amorphous PEO/PTT blended phase) and semi-crystalline PEO phase. Semi-crystalline PEO phase was observed only at temperature below 0 °C for sample containing the highest concentration of PEO segment. The phase structure, thermal and mechanical properties are effected by copolymer composition. The copolymers containing 30÷70 wt% of PEO segment posses good thermoplastic elastomers properties with high thermal stability. Hardness and tensile strength rise with increase of PTT content in copolymers.     

Plasticization and cocrystallization in LLDPE/wax blends

The structure and thermal properties of linear low‐density polyethylene (LLDPE)/medium soft paraffin wax blends, prepared by melt mixing, were investigated by differential scanning calorimetry (DSC) and small‐ and wide‐angle X‐ray scattering (SAXS and WAXS). The blends form a single phase in the melt as determined by SAXS. Upon cooling from the melt, two crystalline phases develop for blends with more than 10 wt % wax characterized by widely different melting points. The wax acts as an effective plasticizer for LLDPE, decreasing both its crystallization and melting temperature. The higher melting point crystalline phase is formed by less branched LLDPE fractions. On the other hand, the lower melting point crystalline phase is a wax‐rich phase constituted by cocrystals of extended chain wax and short linear sequences of highly branched LLDPE chains. The presence of cocrystals was evidenced by standard DSC results, successive self‐nucleation and annealing (SSA) thermal fractionation and by the detection of a new SAXS signal attributed to the lamellar long period of the cocrystals. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 1469–1482     

Multiaxial deformation of polyethylene and polyethylene/clay nanocomposites: in situ synchrotron small angle and wide angle X‐ray scattering study

A unique in situ multiaxial deformation device has been designed and built specifically for simultaneous synchrotron small angle X‐ray scattering (SAXS) and wide angle X‐ray scattering (WAXS) measurements. SAXS and WAXS patterns of high‐density polyethylene (HDPE) and HDPE/clay nanocomposites were measured in real time during in situ multiaxial deformation at room temperature and at 55 °C. It was observed that the morphological evolution of polyethylene is affected by the existence of clay platelets as well as the deformation temperature and strain rate. Martensitic transformation of orthorhombic into monoclinic crystal phases was observed under strain in HDPE, which is delayed and hindered in the presence of clay nanoplatelets. From the SAXS measurements, it was observed that the thickness of the interlamellar amorphous region increased with increasing strain, which is due to elongation of the amorphous chains. The increase in amorphous layer thickness is slightly higher for the nanocomposites compared to the neat polymer. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Phase transitions in poly(heptane-1,7-diyl biphenyl-4,4′-dicarboxylate). SAXS,WAXS and DSC study

The main-chain thermotropic liquid-crystalline poly(heptane-1,7-diyl biphenyl-4,4′-dicarboxylate) (P7MB) was investigated by time-resolved small-angle X-ray scattering (SAXS), wide-angle X-ray scattering (WAXS), and differential scanning calorimerty (DSC). Nonisothermal crystallisation with different rates of cooling and heating was used. On cooling, two phase transitions are observed, isotropic melt - smectic (I-Sm) and Sm- three-dimensional crystalline structure (Sm-Cr), whereas on heating only one transition is observed, Cr-I transition. The transition enthalpies were calculated. Temperature dependences of d-spacings of all crystalline peaks and of the peak observed at high values of scattering vector in the SAXS region were derived. The temperature dependence of the degree of crystallinity was established, based on the integrated intensities of the crystalline peaks and amorphous halo in WAXS.     

Investigation by combined solid‐state NMR and SAXS methods of the morphology and domain size in polystyrene‐b‐polyethylene oxide‐b‐polystyrene triblock copolymers

The microphase structure of a series of polystyrene‐b‐polyethylene oxide‐b‐polystyrene (SEOS) triblock copolymers with different compositions and molecular weights has been studied by solid‐state NMR, DSC, wide and small angle X‐ray scattering (WAXS and SAXS). WAXS and DSC measurements were used to detect the presence of crystalline domains of polyethylene‐oxide (PEO) blocks at room temperature as a function of the copolymer chemical composition. Furthermore, DSC experiments allowed the determination of the melting temperatures of the crystalline part of the PEO blocks. SAXS measurements, performed above and below the melting temperature of the PEO blocks, revealed the formation of periodic structures, but the absence or the weakness of high order reflections peaks did not allow a clear assessment of the morphological structure of the copolymers. This information was inferred by combining the results obtained by SAXS and ¹H NMR spin diffusion experiments, which also provided an estimation of the size of the dispersed phases of the nanostructured copolymers. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 55–64, 2010     

Hybridization of Nafion membranes with an acid functionalised polysiloxane: Effect of morphology on water sorption and proton conductivity

Polysiloxane-modified hybrid Nafion membranes were prepared by casting a mixture of Nafion solution and a precursor of acid functionalised polysiloxane based on tetraethoxysilane and a mercaptan-organoalkoxysilane.Scanning Electron Microscopy (SEM) and Atomic Force Microscopy analysis revealed that the functionalised polysiloxane was dispersed either as finely nanosized inclusions or as coarse domains depending on the rate of the solvent evaporation during the casting procedure. In particular the slower is the rate of solvent evaporation the more interpenetrated and homogenously dispersed at nanosized level is the polysiloxane inside the Nafion membrane.The hybridization process increases the thermal stability of the membranes of about 50 °C relatively to the unmodified Nafion. Small angle X-ray scattering (SAXS) analysis reveals that the hybrid membranes exhibited the typical morphology of Nafion consisting of distinct hydrophilic and hydrophobic domains.Water vapor sorption and proton conductivity were measured varying the temperature (up to 120 °C) and the water activity conditions (from 0.1 to 0.8). The polysiloxane network always increases the water vapor uptake of the membranes and increases significantly the proton conductivity at higher temperature depending on the type of morphology developed by the manufacturing method. In particular hybrid membranes exhibiting nanosized polysiloxane dispersion show a proton conductivity which is up to one-and-half time higher than Nafion recast membrane at high temperature and low water content.     

Structural evolution of melt-drawn transparent high-density polyethylene during heating and annealing: Synchrotron small-angle X-ray scattering study

The morphological development of melt-drawn transparent high-density polyethylene during heating was investigated employing in-situ synchrotron small-angle X-ray scattering (SAXS) technique. The results confirm that at lower temperatures only meridional scattering peaks aligned perpendicular to the extensional flow direction can be observed, indicating a highly oriented lamellar crystallite structure; whereas at higher temperatures an equatorial streak additional to the layer-like meridional scattering pattern develops, reflecting the presence of shish-kebab-like objects in the specimen under investigation. Upon heating, the average thickness of the kebab crystals remains essentially unaffected below 110 °C, and subsequently the selective melting of the less stable kebabs proceeds yielding thicker layered lamellar crystals. When the temperature is raised to 131 °C, the shish-like formation and the thermally stable kebab crystals melt simultaneously. In addition, the microstructure of the melt-drawn specimen subjected to annealing at elevated temperatures was probed at room temperature. As opposed to the SAXS patterns registered at high temperatures, the SAXS diagram measured after annealing shows no equatorial streak, suggesting that the cylindrical structures could be re-formed. This observation can be explained by assuming that the plate-like kebab crystals with their normal parallel to the stretching direction grow and impinge during cooling to room temperature due to secondary crystallization, which can be verified by in-situ SAXS experiments during annealing and subsequent cooling.     

Time-resolved structural studies in fiber processing

Time-resolved and off-line synchrotron wide-angle and small-angle x-ray scattering (WAXS and SAXS) was used to study the structure formation in poly-p-phenylenebenzobisoxazole (PBO) fibers during various stages of spinning, coagulation, and heating processes. WAXS data could be explained in terms of liquid-crystalline structures of varying degrees of order. A structure model is proposed that is in accordance with the observed SAXS four-point pattern.     

Thermo-optical study of UV cured polyether urethane diacrylate films with dispersed octadecanol

Thermally reversible light scattering (TRLS) films are prepared from ultraviolet (UV) curing of polyether urethane diacrylate (PEUDA) with dispersed low molecular weight 1-octadecanol (OD). Depending on the temperature, the OD domains are crystalline or amorphous and this produce opaque or transparent films in a reversible way. Stable optically transparent and light scattering states are obtained after 100 successive heating–cooling cycles. Moreover, morphologies of the OD domains could be varied significantly with the cure temperature and this led to notable discrepancy in optical properties. By using an UV-mask and curing in two steps at different temperatures, complex patterns could be recorded in the film that were encoded at high temperatures (60 °C) and revealed at low temperatures (i.e., at room temperature), which makes the film a candidate for thermo-optical recording medium.     

Dynamic DSC,SAXS and WAXS on homogeneous ethylene-propylene and ethylene-octene copolymers with high comonomer contents

Ethylene-propylene (EP) and ethylene-octene (EO) copolymers polymerized with the aid of homogeneous vanadium and metallocene catalysts were compared by DSC and time-resolved simultaneous SAXS-WAXS-DSC at scanning rates of 10 and 20°C min^?1 using synchrotron radiation. An EP copolymer with a density of 896 kg m^?3 (about 89 mol % ethylene) after compression moulding gave orthorhombic WAXS reflections. The crystallinity as a function of temperature [w ^c (T)] calculated from these reflections using the two-phase model was in good agreement withw ^c (T) calculated fromc _p measurements using DSC. Thec _p measurements also enabled calculation of the baselinec _p and the excessc _p. The SAXS measurements revealed a strong change in the long period in cooling and in heating. The SAXS invariant as a function of temperature showed a maximum in both cooling and heating, which could be explained from the opposing influences of the crystallinity and the electron density difference between the two phases. Two EO copolymers with densities of about 871 kg m^?3 (about 87 mol% ethylene) no longer showed any clear WAXS reflections, although DSC and SAXS measurements showed that these copolymers did crystallize. The similarity between the results led to the conclusion that the copolymers, though based on different catalyst systems — vanadium and metallocene — did not have strongly different sets of propagation probabilities of chain growth during polymerization. On the basis of a Monte Carlo simulation model of crystallization and morphology, based on detailed knowledge of the microchain structure, the difference between WAXS on the one hand and DSC and SAXS on the other could be explained as being due to loosely packed crystallized ethylene sequences in clusters. These do cause the density and the electron density of the cluster to increase (which is measurable by SAXS) and the enthalpy to decrease (which is measurable by DSC) but the clusters are too small and/or too imperfect to give constructive interference in the case of WAXS. Of an EP copolymer with an even lower ethylene content (about 69 mol %), the crystallization and melting processes could still be readily measured by DSC and SAXS, which proves that these techniques are eminently suitable for investigating the crystallization and melting behaviour of the copolymers studied.     

Synchrotron SAXS and WAXS Studies on Changes in Structural and Thermal Properties of Poly[(R)‐3‐hydroxybutyrate] Single Crystals during Heating

Summary: The annealing and melting behavior of poly[(R)‐3‐hydroxybutyrate] (P(3HB)) single crystals were followed in real time by synchrotron small‐ (SAXS) and wide‐angle X‐ray scattering (WAXS) measurements. The real‐time SAXS measurements revealed that the P(3HB) single crystal exhibits a discontinuous increase of lamellar thickness during heating. The structural changes as observed by SAXS and WAXS were in response to the thermal properties of single crystals characterized by differential scanning calorimetry.

A series of two‐dimensional small‐angle X‐ray scattering patterns of P(3HB) single crystal mats during the lamellar thickening process.     

Confined lamella formation in crystalline-crystalline poly(ethylene oxide)-b-poly(ɛ-caprolactone) diblock copolymers

The real time and in situ investigation of the crystallization process and structure transitions of asymmetric crystalline-crystalline diblock copolymers from the melt was performed with synchrotron simultaneous SAXS/WAXS. The asymmetric poly(ethylene oxide)-b-poly(ε-caprolactone) diblock copolymers were chosen for the present study. It was shown that the short blocks crystallized later than the long blocks and final lamellar structure was formed in all of the asymmetric diblock copolymers. The final lamellar structure was confirmed by AFM observation. The SAXS data were analyzed with different methods for the early stage of the crystallization. The Guinier plots indicated that there were no isolated domains formed before the formation of lamellae in the asymmetric diblock copolymers during the crystallization process. Debye-Bueche plots implied the formation of correlated domains during crystallization.     

Study on the rapid deswelling mechanism of comb-type N-isopropylacrylamide gels

The shrinking mechanism of comb-type grafted poly(N-isopropylacrylamide) gel was investigated by fluorescence spectroscopy and small-angle X-ray Scattering (SAXS). The SAXS reveals that the microdomain structure with characteristic dimension of 460 Å is developed in the comb-type grafted poly(N-isopropylacrylamide) gel during the shrinking process. Fluorescence spectroscopy together with SAXS observation suggests that the freely mobile characteristics of the grafted chains are expected to show the rapid dehydration to make tightly packed globules with temperature, followed by the subsequent hydrophobic intermolecular aggregation of the dehydrated graft chains. The dehydrated grafted chains created the hydrophobic cores, which enhance the hydrophobic aggregation of the networks. These aggregations of the NIPA chains contribute to an increase in void volume, which allow the gel having a pathway of water molecules by the phase separation.     

Polymorphism in yttrium molybdate Y2Mo3O12

Yttrium molybdate (Y₂Mo₃O₁₂) has been prepared by non-hydrolytic sol–gel chemistry. The phase evolution upon heating was investigated using in situ and ex situ heat treatments combined with powder X-ray diffraction. This method has led to the isolation of two orthorhombic phases with different atomic connectivity. Yttrium adopts 6- and 7-coordinate sites in the Pbcn and Pba2 structures, respectively. Cocrystallization of both phases was observed in a narrow temperature range, suggesting that crystallization kinetics play a major role in phase formation. It was found that the Pba2 phase is the stable polymorph below 550 °C, and converts to Pbcn at higher temperatures.     

The effect of glucose and temperature on the in vivo efficiency of photochemotherapy with meso-tetra-hydroxyphenyl-chlorin

Balb/c athymic nude mice bearing WiDr human colon adenocarcinoma have been employed to investigate the effect of glucose administration, cooling or slight heating on the anti-tumor activity of photochemotherapy (PCT) with meso-tetra-hydroxyphenyl-chlorin (mTHPC). An apparent delay in the tumor growth is found by combining PCT with either single or multiple injections of glucose. The anti-tumor effect of PCT is slightly enhanced by cooling the tumor to 5°C. Cooling also enhances the efficiency of PCT and glucose injection combined. Heating the tumor to 37°C has no significant effect on either PCT alone or on the combination of PCT and glucose injection. Furthermore, the kinetics of the accumulation of mTHPC in tissue have been studied. Single or multiple injections of glucose have an enhancing effect on the accumulation of mTHPC in the tumor.     

Characterization of pore structure in metal-organic framework by small-angle X-ray scattering

MOF-5-like crystals were studied by small-angle X-ray scattering (SAXS) to reveal, both quantitatively and qualitatively, their real structural details, including pore surface characteristics, pore shape, size distribution, specific surface area (SSA), spatial distribution, and pore-network structure. A combined SAXS and wide-angle X-ray scattering (WAXS) experiment was conducted to investigate the variation of the pore structure with the MOF-5 crystalline phase produced at different cooling rates. The SSA of the MOF-5 crystals synthesized herein spanned a broad range from approximately 3100 to 800 m2/g. The real pore structures were divided into two regimes. In regime I the material consisted mainly of micropores of radius approximately 8 A as well as mesopores of radius 120 approximately 80 A. The structure in regime II was a fractal network of aggregated mesopores with radius >or=32 A as the monomer, reducing SSA and hydrogen uptake capacity at room temperature. The two regimes can be manipulated by controlling the synthesis parameters. The concurrent evolution of pore structure and crystalline phase during heating for solvent removal was also revealed by the in-situ SAXS/WAXS measurement. The understanding of the impact of the real pore structure on the properties is important to establish a favorable synthetic approach for markedly improving the hydrogen storage capacity of MOF-5.     

Preparation and properties of new flame retardant unsaturated polyester nanocomposites based on layered double hydroxides

The preparation of new layered double hydroxides/unsaturated polyester (LDH/UP) nanocomposites was performed and the effect of LDH on the resin properties was studied. Two different organo-LDHs have been prepared, adipate-LDH (A-LDH) and 2-methyl-2-propene-1-sulfonate-LDH (S-LDH); in order to evaluate the influence of these nanofillers, samples with two different concentrations were dispersed in the matrix. The physical, thermal, mechanical and fire reaction properties of nanocomposites were studied. Intercalated layered structures were observed for the different organo-LDH loadings (1 and 5 wt%). Mechanical properties studied under flexural tests show that incorporation of organo-LDH in the resin reduces the flexural strength of polyester resin while the flexural modulus is unchanged for the S-LDH/UP composites and increased with 1 wt% of A-LDH. Adding 1 wt% of A-LDH to the resin produces an important reduction on the flexural strength, but an increase of the flexural modulus. The study of fire reaction properties, using cone calorimeter, suggested a significant reduction in the UP flammability, by 46 and 32%, by incorporating 1 wt% of A-LDH and 5 wt% S-LDH, respectively. Mass loss curves show enhanced char formation with the different loads tested while the amount of evolved smoke remains quite unchanged.     

Anomalous rheology in a nanostructured diblock copolymer/hydrocarbon system and its kinetic origin

Nanostructured squalane solutions (5–20 wt %) of a diblock copolymer, poly(styrene‐b‐hydrogenated isoprene), were prepared by a cosolvent‐casting method. The as‐cast solutions behaved as viscous liquids with terminal flow behavior at room temperature. Upon heating, the solutions gelled, and they did not return to their starting liquidlike state upon cooling. Small‐angle X‐ray scattering (SAXS) revealed a random array of spherical micelles in the as‐cast solutions, which were hypothesized to be in a nonequilibrium state. This abnormal solidification with increasing temperature was correlated with the formation of body‐centered‐cubic (BCC) structures. Isothermal SAXS and rheology measurements also indicated that the rate of formation of BCC structures in the as‐cast solutions increased with temperature. A diffusion‐controlled nucleation‐and‐growth mechanism was proposed for the ordering process in the as‐cast polystyrene‐b‐hydrogenated polyisoprene/squalane solutions. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1496–1505, 2004     

Preparation and properties of thermosensitive hydrogel microcapsules

Temperature-sensitive hydrophilic gel microcapsules have been newly prepared. That is, poly ( -lysineisopropylamide–terephthalic acid) microcapsules containing water have been obtained by an interfacial polymerization at a water/oil interface between -lysineisopropylamide and terephthaloyldichloride. The microcapsule changes its size between 33 and 35°C. Under 33°C, the microcapsules are fully spherical and can be redispersed in distilled water, while are aggregated above 35°C. The microcapsules, which are observed to show aggregation above 33°C, can be redispersed by decreasing temperature within a few second. The thermosensitive morphological changes of the microcapsules are thus reversible. Also, it has been shown that the permeability of sodium chloride through the microcapsule membrane changes remarkably between 33 and 35°C, while it is kept almost constant independent of temperature between 25 and 33°C or between 35 and 55°C. The permeability of solutes is higher under 33°C than that above 35°C. Such thermosensitive properties result from the fact that the polymer membrane has isopropylamide groups. That is, -lysineisopropylamide has a chemical structure similar to N-isopropylacrylamide, the polymer of which, poly (N-isopropylacrylamide), is a thermosensitive hydrogel having its phase transition temperature around 33°C.     

Rhodamine-conjugated acrylamide polymers exhibiting selective fluorescence enhancement at specific temperature ranges

A simple copolymer, poly(NIPAM-co-RD), consisting of N-isopropylacrylamide (NIPAM) and rhodamine (RD) units, behaves as a fluorescent temperature sensor exhibiting selective fluorescence enhancement at a specific temperature range (25–40 °C) in water. This is driven by a heat-induced phase transition of the polymer from coil to globule. At low temperature, the polymer exists as a polar coil state and shows very weak fluorescence. At >25 °C, the polymer weakly aggregates and forms a less polar domain within the polymer, leading to fluorescence enhancement. However, at >33 °C, strong polymer aggregation leads to a formation of huge polymer particles, which suppresses the incident light absorption by the RD units and shows very weak fluorescence. In the present work, effects of polymer concentration and type of acrylamide unit in the polymer have been investigated. The increase in the polymer concentration in water leads to a formation of less polar domain even at low temperature and, hence, widens the detectable temperature range to lower temperature. Addition of N-n-propylacrylamide (NNPAM) or N-isopropylmethacrylamide (NIPMAM) component to the polymer, which has lower or higher phase transition temperature than that of NIPAM, enables the aggregation temperature of the polymer to shift. This then shifts the detectable temperature region to lower or higher temperature.