聚芳基乙炔树脂/杉木粉木材陶瓷的制备与表征

用聚芳基乙炔树脂浸渍杉木粉,固化制得聚芳基乙炔/杉木粉复合材料,经高温炭化得到了一种新型木材陶瓷。 用DTG分析了聚芳基乙炔树脂和复合材料的热稳定性,用XRD、LRS和SEM研究了炭化温度和树脂用量对木材陶瓷物相构成、断面微孔形态和抗压强度的影响。 结果表明,木材陶瓷呈三维多孔结构,孔分布比较均匀;复合材料保持了很高的热分解温度(325 ℃)和残碳率(70%)。 随着炭化温度升高,d002晶面间距由0.3895 nm减小至0.3530 nm,而微晶尺寸Lc和La有不同程度增加。 木材陶瓷的开孔率随炭化温度的升高由31.5%减小至20.1%,而抗压强度由3.0 MPa增大至6.2 MPa。 树脂/杉木粉质量比对木材陶瓷的微孔尺寸和形状有较大影响,但对石墨微晶尺寸影响不明显。     

聚醚酯嵌段共聚物熔体的流变性能

采用毛细管流变仪测定了组成比、聚醚分子量、熔融时间和熔融温度对嵌段聚醚酯熔体表观粘度的影响．结果发现在所研究的温度和切变速率范围内,该结构聚醚酯熔体为假塑性非牛顿流体,其粘度随聚酯段含量的增加而增加,随熔融时间增加而降低,随聚醚分子量的增大而增大．聚醚酯的零切粘度可由Ｓｐｅｎｃｅｒ Ｄｉｌｌｏｎ 公式外推得到,零切粘度对温度的依赖关系服从Ａｎｄｒａｄｅ 公式．     

荧光探针法研究PEO-PPO嵌段共聚物胶束的特性

利用十六烷基罗丹明B作为主要荧光探针，研究了水溶性嵌段共聚物PluronicF－68在水溶液中的胶束化行为．研究表明：PluronicF－68形成胶束的临界胶束浓度与温度有极大关系，随温度的升高，其CMC值急剧下降，并且温度对胶束的性质也有很大影响，温度升高可导致胶束的微观粘度增大，表现出很强的负粘－温效应，并发现引起这种负粘－温效应的主要原因是PluronicF－68分子中聚环氧乙烷（PEO）链随温度升高亲水性变差引起其收缩所致，而由聚环氧丙烷（PPO）形成的内核的微观粘度随温度的升高略有下降．     

γ-Mo2N催化剂上的乙炔选择加氢

 采用固定床连续流动反应器对γ－Mo2N催化剂上的乙炔加氢反应进行了研究．在150℃的反应温度下,乙炔的转化率为95％,乙烯的选择性达到80％,乙烷和丁烯的选择性分别为4％和10％．反应温度和空速的变化对反应产物的选择性没有明显的影响．在同样的反应条件下,钯催化剂上乙炔加氢反应的主要产物是乙烷,产物组成随反应温度和空速的变化而变化．对γ－Mo2N上的乙炔选择加氢生成乙烯的机制进行了解释,认为γ－Mo2N表面上滞留的强吸附的碳氢物种可能有利于乙炔高选择性地生成乙烯．     

微波复合直流等离子体转化天然气制乙炔的研究

利用微波复合直流等离子体对天然气转化制乙炔反应进行了研究. 考察了氢烷比、气体流量、功率等参数对装置的能量利用率以及天然气转化反应的影响, 并考核了微波复合直流等离子体转化天然气制乙炔工艺的稳定性. 实验结果表明: 微波复合直流等离子体装置的能量利用率随等离子体工作气体的流量的增加而提高; 由于微波的作用使传统直流柱状等离子体分化为多根丝状等离子体, 从而使得电极的烧蚀方式由传统的点烧蚀变为面烧蚀, 并大幅度提高等离子体转化天然气工艺的稳定性和电极寿命; 甲烷的转化率和乙炔的收率随功率的增加而提高, 随CH₄/H₂比和气体流量的增加而降低, 在氢烷比为0.9、总气体流量为760 L/min、微波源输出电功率6 kW、直流电源输出功率90 kW时, 甲烷转化率可达84.4%, 乙炔选择性为75.6%, 乙炔收率为63.8%, 乙炔能耗达10.8 kWh•kg^－1; 电极寿命超过200 h.     

聚电解质──壳聚糖浓溶液流变学性质研究：浓度、温度、溶剂pH值和外加盐对粘度及流动性的影响

本工作用日本岩本ＲＰＸ－７０５多功能流变仪测定了在不同浓度，温度，溶剂ｐＨ值和外加盐浓度对壳聚糖在甲酸水溶液中其浓溶液粘度η随剪切速率γ的变化关系，讨论了浓度，温度等对溶液粘度，流动活化能Ｅγ和流动指数ｎ的影响。发现溶剂ｐＨ值减小或溶液中外加盐浓度增加，溶液粘度变小，ｎ增大，表明非牛顿流动性减弱，并且进一步了零剪切粘度ηｏ和外加盐浓度Ｃｓ的依赖关系。     

氰乙基纤维素/二甲基甲酰胺液晶溶液的流变行为

本文通过测定不同浓度的溶液在不同温度和切变速率下的粘度,讨论了氰乙基纤维素/二甲基甲酰胺溶液的流变行为。溶液的流动曲线表明,该溶液是一种假塑性液体。在浓度较高时,存在屈服现象,屈服应力的大小与浓度和温度有关。溶液的浓度—粘度曲线表示出典型的液晶行为。粘度与浓度的关系和屈服应力与浓度的关系相似。溶液的临界浓度随温度的升高而增加。在单相区(各向同性相或液晶相),粘度随温度升高而降低,表观流动活化能大于零。但在两相区,粘度随温度的升高而增大,表观流动活化能小于零。该实验得到的临界浓度与通过光学的方法所得的临界浓度是一致的。     

甲烷在水-叔丁醇混合溶剂中的溶解度

在303.15 K、313.15 K、323.15 K、333.15 K温度下，0－6 MPa压力范围内测定了甲烷在水－叔丁醇混合溶剂中的溶解度．溶剂中叔丁醇的摩尔分数(x_(TBA))从0到1．结果表明，在温度和溶剂组成一定条件下，甲烷的溶解度随其分区的增加而增大，随x_(TBA)的增加，在富水区内，甲烷的溶解度变化较缓慢，当x_(TBA)超过某值时，甲烷的溶解度随x_(TBA)的增加而增大，并且幅度较大；在x_(TBA)约为0－0.045范围内，甲烷的溶解度随温度增加而减小，x_(TBA)约在0.045－0.15范围内，溶解度随温度增加而增加，x_(TBA)约在0.15～1.0范围内，溶解度随温度增加而减小．根据溶解度与温度和溶剂组成的关系可以推测，在303.15－333.15 K、0－6 MPa范围内，水－叙丁醇混合溶剂中仍存在笼合物结构．根据溶解度与温度、压力的关系讨论了甲烷在此混合溶剂中的亨利常数、偏摩尔体积、标准溶解自由能、标准溶解焓和标准溶解熵．     

含氰基离子液体的合成、表征及流变性质研究

摘要合成、 表征了一系列新的含氰基咪唑类离子液体. 测定了该离子液体的密度、 熔点及溶解性等物理性质, 研究了其在稳态、 瞬态和动态条件下的流变行为. 结果表明, 当剪切速率在0.1～50 s^-1范围内时, 其粘度不随剪切速率的变化而变化, 但随温度升高而降低, 粘流活化能随取代基长度变化呈现规律性变化. 对于1-丁基-3-氰乙基咪唑六氟磷酸盐离子液体, 维持剪切速率不变时, 其剪切应力和粘度均不随时间变化, 且随着温度的升高而降低; 在动态条件下, 在线性粘弹区, 复合粘度和损耗模量G″ 随温度升高而降低. 关键词     

聚电解质──壳聚糖浓溶液流变学性质研究：浓度、温度、溶剂pH值和外加盐对粘度及流动性的影响

本工作用日本岩本ＲＰＸ－７０５多功能流变仪测定了在不同浓度、温度、溶剂ｐＨ值和外加盐浓度对壳聚糖在甲酸水溶液中其浓溶液粘度η随剪切速率γ的变化关系．讨论了浓度、温度等对溶液粘度、流动活化能Ｅ_γ和流动指数ｎ的影响．发现溶剂ｐＨ值减小或溶液中外加盐浓度增加，溶液粘度变小，ｎ增大，表明非牛顿流动性减弱，并且进一步讨论了零剪切粘度η_０和外加盐浓度Ｃ_ｓ的依赖关系．     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

Cu0-catalysed 1,3-dipolar cycloadditions of α-amino acid derived N,N-cyclic azomethine imines to ynones

A series of 20 CuAIAC reactions between eight 4-acylamino substituted pyrazolidine-3-one-1-azomethine imines and four terminal ynones were performed using Cu⁰ as catalyst. The corresponding fluorescent cycloadducts were obtained in very high yields upon simple workup. Thus, Cu-metal turned out to be a better catalyst than Cu^I in terms of yield and ease of isolation. Availability of azomethine imines, mild reaction conditions, and simple workup enable a “click” access to libraries of densely substituted 2,3-dihydro-1H,5H-pyrazolo[1,2-a]pyrazol-1-ones. Reactivity of differently substituted dipoles was evaluated experimentally and by quantum chemical methods (DFT).     

Synthesis and antioxidative/anti-inflammatory activity of novel fullerene–polyamine conjugates

(E)-4-(Fullerenopyrrolidin-1-yl)-3-methylbut-2-enoic acid and its corresponding succinimidyl ester, readily obtained through Prato-type modification of C₆₀, were used for the selective N-acylation of polyamines. The thus obtained conjugates were evaluated for their antioxidative and anti-inflammatory activity and their cytotoxicity was determined. Members of this family of compounds showed interesting anti-lipid peroxidation, anti-lipoxygenase and anti-inflammatory activity and comparable cytocompatibility to spermidine.     

Copper-catalyzed multicomponent reactions of 2-iodoanilines,benzylamines, and elemental sulfur toward 2-arylbenzothiazoles

A relatively cheap copper salt-catalyzed, three-component approach providing 2-arylbenzothiazoles in good to excellent yields from readily available 2-iodoanilines, benzylamines, and sulfur powder is reported. This methodology allows preparation of various classes of 2-arylbenzothiazoles and provides a general, reliable approach.