溶剂替换法制备氟铃脲水悬浮剂及其分散稳定性

采用溶剂替换法制备了氟铃脲水悬浮剂,通过测定颗粒的平均粒径Dav和颗粒界面的Zeta电位,研究了分散剂种类、添加量以及有机相中乙醇的加入量对水悬浮剂分散稳定性的影响。 结果表明,在相同条件下,以苯乙烯丙烯酸共聚物(MOTAS)作为分散剂制备的水悬浮剂的分散效果较好;当MOTAS添加质量分数为1%时,Dav最小,Zeta电位绝对值最大,体系分散稳定性最好;在有机相中添加乙醇可以显著提高氟铃脲水悬浮剂的分散稳定性,当有机相中乙醇的加入质量分数增加至31.2%时分散稳定性达到最好。     

体系pH值、乳化温度和电解质离子对异丙甲草胺水乳剂稳定性的影响

通过测定药物液滴的平均粒径和Zeta电位研究了体系pH值、 乳化温度和电解质离子对乳化剂三苯乙烯基苯酚聚氧乙烯醚磷酸酯三乙醇胺盐(SCP)稳定的异丙甲草胺水乳剂稳定性的影响. 结果发现, 体系的pH值影响SCP分子在水中的电离能力, 当pH=9时, SCP完全电离, 能为液滴提供较大的静电稳定作用, 水乳剂稳定性最好; 乳化温度低时, SCP分子向液滴界面扩散慢, 且舒展不完全, 液滴所带负电荷较少, 水乳剂稳定性差; 温度升高后, 水相黏度减小, 布朗运动加剧, 液滴碰撞合并几率增大, 且SCP分子热运动增强, 易从界面逃逸, 液滴间静电斥力减弱, 同时SCP亲水性下降, 水乳剂稳定性变差; 电解质离子会压缩界面双电层, 降低Zeta电位, 液滴带电量减少而聚结, 离子浓度越大, 电荷数越大, 水乳剂稳定性越差. 在相同的离子浓度下, 水合半径小的Ca²⁺压缩双电层能力强于Mg²⁺, 添加Ca²⁺后水乳剂稳定性更差.     

基于Ugi多组分反应的海藻酸酰胺衍生物改性二氧化硅纳米粒子的制备

采用海藻酸酰胺衍生物通过Ugi多组分反应制备了新颖的聚合物-二氧化硅(Oct-Alg-Si O_2)纳米粒子.通过氢核磁共振波谱(~1H NMR)和X射线光电子能谱(XPS)对Oct-Alg-Si O_2的结构和表面元素组分进行了表征.采用透射电子显微镜(TEM)、Zeta电位和激光粒度分析仪对Oct-Alg-Si O_2的形貌、粒径和胶体性能进行了探索.结果表明,海藻酸酰胺衍生物共价接枝到氨基二氧化硅(Si O_2-NH_2)纳米粒子的表面,提高了其平均直径,调控了其Zeta电位,在水介质中能够表现出良好的分散稳定性.以10%的液体石蜡为油相,采用Oct-Alg-Si O_2制备了Pickering乳液.在油水界面能够形成液滴粒径为5.7μm的稳定Pickering乳液.随着水相p H值的增大,乳液体积分数增大,稳定性增强.细胞相容性实验结果表明,Oct-Alg-Si O_2纳米粒子具有极好的生物相容性.     

聚合物分散剂对氟虫脲水悬浮剂分散稳定性的影响

通过测定药物颗粒界面Zeta电位和平均粒径, 研究了聚合物分散剂苯乙烯磺酸聚合物钠盐(GY-D08)用量、pH和盐离子对氟虫脲水悬浮剂分散稳定性的影响, 研究结果表明, 分散剂GY-D08的加入量与水悬浮剂分散效果密切相关, 制备质量分数为5%氟虫脲水悬浮剂的GY-D08最佳用量为2%, GY-D08用量过多或过少都会使分散效果下降; pH影响分散剂GY-D08在水中的电离能力, 当pH=9时, GY-D08分子完全电离, 能为颗粒提供较大的静电位阻, 水悬浮剂分散稳定性最好; Mg²⁺或Ca²⁺压缩颗粒界面的双电层, 降低Zeta电位, 使颗粒因带电量减少而聚结, 导致水悬浮剂分散稳定性变差, 且Mg²⁺或Ca²⁺浓度愈大, 其分散稳定性愈差; 当离子浓度相同时, Ca²⁺压缩双电层的能力比Mg²⁺强, 添加Ca²⁺后的水悬浮剂的分散稳定性更差.     

Zeta电位和界面膜强度对水包油乳状液稳定性影响

通过对表面活性剂、聚合物溶液和煤油体系油水界面剪切黏度和油珠的Zeta电位的测定,考察了界面膜强度和Zeta电位对水包油乳状液稳定性的影响。在煤油、表面活性剂、聚合物聚丙烯酰胺(3530S)或其氧化降解聚合物体系中,含有3530S时,界面膜强度值最大,最大值大于0.10 mN/m,Zeta电位为-18.4 mV,绝对值最大,乳状液最稳定。结果表明,油水界面膜强度和油珠表面的Zeta电位对水包油乳状液稳定性影响较大。界面膜强度和Zeta电位绝对值较大时,乳状液最稳定;当界面膜强度相差不大时,Zeta电位绝对值大的乳状液较稳定,此时双电层对乳状液稳定性起主要作用;当Zeta电位相差不大时,界面膜强度大的乳状液较稳定,此时界面膜强度对乳状液稳定性起主要作用。研究还表明,机械或氧化降解后的聚合物体系,界面剪切黏度和Zeta电位绝对值变小,乳状液稳定性变差。     

胶质液体泡沫的微观结构研究

采用冷冻蚀刻电子显微镜技术(FF-TEM)、小角X射线散射(SAXS)、偏光显微镜以及差示扫描量热分析(DSC)等手段对组成为十二烷基醇聚氧乙烯(3)醚(AEO-3)/正癸烷/十二烷基硫酸钠(SDS)或Tween 80/水的胶质液体泡沫(CLA)体系的微观结构进行了系统分析. 分析结果表明, CLA是由微米级的油相颗粒(富油相)和包围着它的外层水相液膜(富水相)组成, 且在富油相和富水相区内分别有诸如反胶束和胶束或O/W微乳液等超分子聚集体结构存在. 通过对不同组成和不同相体积比(PVR)的CLA之间, 以及与高内相普通乳状液(HIPRE)在粒径大小、组成、制备方法、结构特征、稳定性等方面的比较, 发现CLA与HIPRE具有相似的结构轮廓. 这一结论在一定程度上支持了Princen等有关CLA结构与本质的论点.     

聚乙二醇接枝聚乳酸的自组装纳米微球的制备及性能

对制备的新型聚乙二醇(PEG)接枝聚乳酸(PLA)在水中的自组装性能进行研究, 探讨其作为纳米药物载体的可行性和稳定性. 目测法得到其溶解度为(2.16～4.32)×10^－2 mg•mL^－1; 荧光法得到聚合物的临界胶束浓度为1.12×10^－3 mg•mL^－1; 透射电子显微镜观察显示该聚合物在水中的自组装聚集体为纳米级球形; 动态激光光散射测试微球的粒径和Zeta电位发现, 在微球的制备过程中, 聚合物的亲/疏水性比例、水相介质及水溶液的pH值对它影响显著; 而制备后, 稀释和冷冻对它无显著影响, 改变微球的环境pH值至酸性, 出现聚集, 至碱性无影响. 研究结果显示, 该聚合物在水和磷酸钠盐缓冲液中可形成稳定的纳米微球, 通过微球的制备条件和存在环境可控制其粒径和Zeta电位, 因此根据应用需要, 通过控制其粒径和Zeta电位, 可能提高微球的在体血液循环时间并实现靶向缓释.     

阳离子修饰纳米Pt的合成及其在Nafion膜上的自组装行为研究

以季铵阳离子聚合物为修饰离子、乙醇为还原剂,在水溶液中合成了具有稳定电位的阳离子修饰纳米Pt颗粒,还原过程采用UV-vis光谱监控,粒子形貌采用TEM表征.结果表明,合成体系在45 min左右还原完毕,颗粒粒径约为4.5 nm,呈多晶态结构,粒径分布狭窄,具有良好的分散性.采用Zeta电位测定仪分析了不同pH条件下粒子的电位,选择了合适的组装pH值并运用静电自组装的方法把Pt颗粒成功地组装到Nafion膜表面.同时对该自组装体系的影响因素进行了一些理论分析,并以此对组装过程的动力学性质和组装膜电化学特性进行了解释.     

无皂乳液聚合法制备非球形聚苯乙烯粒子研究

采用苯乙烯(St)、二乙烯基苯(DVB)、甲基丙烯酰氧乙基三甲基氯化铵(DMC)为单体,在乙醇和水混合介质中通过无皂乳液聚合法制备了非球形聚苯乙烯(PS)粒子。通过FT-IR、TEM和激光粒度及电位分析仪对粒子的结构、形貌、粒径以及Zeta电位进行了表征。结果表明,所合成PS粒子均含三种单体结构单元,且形貌上均为非球形;随着DVB用量的增加,PS粒子形貌更趋于球形,粒径和单分散系数均逐渐增加;随DMC用量增加,PS粒子粒径随之增加,单分散系数逐渐减小,表面Zeta电位也逐渐增加;KHCO3用量的增加能使PS粒子粒径和单分散系数均增加;随着醇水比的减小,PS粒子粒径逐渐减小,而单分散系数则逐渐增加。     

丙烯酸酯共聚物无皂水溶胶稳定性的研究

用溶液聚合法合成了四种AA含量不同的丙烯酸酯共聚物(MMA/BA/HEMA/AA)，通过中和AA使共聚物带有—COO~-能起自乳化作用分散于水中而成为无皂水溶胶．TEM观察表明水溶胶粒子呈球状，单分散性好，粒径随AA含量增加而变小，在30～90 nm范围．用电导滴定法测定水溶胶粒子中—COOH和—COO~-的分布，表明绝大部分—COO~-处于粒子表面，并且随AA含量增加，粒子表面的—COO~-增多，Zeta电位增大，这是导致水溶胶的抗电解质稳定性(以C.C.C.值反映)和贮存稳定性(以表现粘度反映)随AA含量增加而提高的主要原因。     

A study on organized assemblies in the sodium alkylcarboxylate/fatty alcohol/water systems

The phase behavior and evolution of self-organized assembling structures in the sodium alkylcarboxylate/fatty alcohol systems were investigated by TEM.With increasing concentration of fatty alcohol,the micelles transform into lamellar La phase,sponge L3 phase,multilamellar vesicle,and transfonn back to lamellar La phase.At higher alcohol concentration,a stable two aqueous phase coexisting region has been observed in this kind of systems after aged two months.Unilamellar vesicles were found both in two separated phases but the vesicle density of the upper phase is much higher than that of the bottom phase.     

环境因素对正负表面活性剂体系相行为的影响

在1:1正负离子表面活性剂混合体系(十二烷基硫酸钠/辛基三甲基溴化铵 SDS-C8NM3Br; 十二烷基硫酸钠/十二烷基三甲基溴化铵,SDS-C12NM3Br)中加入短链脂肪醇 (乙醇,正丙醇,正丁醇),正负离子表面活性剂沉淀溶解,出现表面活性剂双水相.上相有液晶存在,下相有囊泡自发形成.折光率数据和电镜结果表明:上相为表面活性剂富集相,下相表面活性剂浓度较低.混合体系中,出现表面活性剂双水相所需短链脂肪醇的体积百分数,随短链脂肪醇的链长增加而降低.温度升高,出现表面活性剂双水相所需短链脂肪醇的体积百分数降低.对SDS/C8NM3Br/H2O体系的研究结果表明:超声处理,可使混合体系中沉淀向囊泡转化,与短链脂肪醇的加入后的作用类似.     

Antiseptic Nanocapsule Formation via Controlling Polymer Deposition onto Water-in-Oil Miniemulsion Droplets

The stable nanodroplet was prepared by inverse miniemulsion with an aqueous antiseptic solution dispersed in an organic medium of solvent/nonsolvent mixture containing an oil-soluble surfactant and the polymer for shell formation. The change in gradient of the solvent/nonsolvent mixture, obtained by heating at 50 °C, led to the precipitation of the polymer in the organic phase and deposition onto the large interphase of the aqueous miniemulsion droplets. The monodisperse polymer nanocapsule, with the size range of 80–240 nm, dispersed in cyclohexane phase was achieved as a function of surfactant concentration. By variation of polymer content, molecular weight and type, an encapsulation efficiency of 20–100% was obtained as detected by proton-nuclear magnetic resonance spectroscopy measurement. The nanocapsule could be easily transferred into water as continuous phase resulting in aqueous dispersion with nanocapsule containing the antiseptic agent as an aqueous core. The encapsulated amount of the antiseptic agent was evaluated to indicate the durability of the nanocapsule's wall. Additionally, the different types of polymer having glass transition temperature ranging from −60 to 100°C have been successfully used. Currently, the research work on the incorporation of nanocapsules onto natural rubber (NR) latex in order to prepare NR latex glove containing the antiseptic agent nanocapsules is carried out. By using the simple and versatile layer-by-layer (LbL) technique based mainly on an electrostatic interaction between oppositely charged species, the deposition of nanocapsules onto NR latex film has successfully been fulfilled.     

脂肪醇和电解质对丙酸十二铵盐在四氯化碳中增溶水的影响

研究了己醇，辛醇、Ｋｕｉ醇和月桂醇对丙酸十二铵（ＤＡＰ）－四氯化碳反胶束溶液增溶水和氯化钠水溶液的影响，在ＤＡＰ浓度固定时，水增溶量对醇浓度的关系出现极大值，在醇浓度相同时，长碳链醇较短碳链醇有更大的增溶水能力，在固定ＤＡＰ浓度和增溶水量最大时，氯化钠的存在将导致水溶液增溶量的显著下降，乙酸十二铵（ＤＡＡ）、ＤＡＰ和丁酸十二铵（ＤＡＢ ）的四氯化碳溶液对氯化钠水溶液的增溶量随氯化钠浓度的升高而有不     

Removal of organic dyes from water by liquid-liquid extraction using reverse micelles

In the present work, solvent extraction using reverse micelles is proposed for the removal of organic dyes from water. In this approach, the dye is solubilized in the aqueous core of the reverse micelles, which are present in the organic phase. The organic phase is subsequently separated from the aqueous phase leading to signifi-cant removal of dye. Experimental results reveal that the electrostatic interaction between the oppositely charged surfactant head group present in the reverse micelles and the dye molecule plays a key role in the separation. The removal of the anionic methyl orange dye from water is carried out in the presence of cationic hexadecyltrimethyl ammonium bromide surfactant, whereas the removal of the cationic methylene blue dye is carried out in the presence of anionic sodium dodecylbenzene sulfonate surfactant. Amyl alcohol is used as the solvent. The influence of parameters such as dye concentrations, surfactant concentrations, pH, and KCl and NaBr concentrations on the percentage removal of dye was studied. The percentage removal of dye is decreased with the increase in dye concentration in the feed. The increase in surfactant concentration resulted in higher dye removal, because more reverse micelles could be hosted in the organic phase. The increase in aqueous phase pH resulted in enhanced removal of methyl orange from water, while in the case of methylene blue the percentage removal decreased. The increase in KCl and NaBr concentrations resulted in decreased percentage removal of methylene blue, whereas the percentage removal of methyl orange was increased. The effect of pH and salt concentration is explained based on charge transfer mechanism and electrostatic interactions and dye-surfactant complex formation.     

MASS TRANSPORT EFFECTS ON THE STABILITY OF EMULSION: EMULSION FILMS WITH ACETIC ACID AND ACETONE DIFFUSING ACROSS THE INTERFACE

The stability of emulsions is studied using, as a model of two interacting drops, an aqueous film of a surfactant immersed in an oil phase. It is shown that the mass transfer of a solute across the film changes its life-time. This change depends on several parameters as the nature and concentration of the solute. the direction of mass transfer, the time elapsed after the formation of the film. The destabilizing effect, of the transfer is found to be much less pronounced when the solute is in the continuous water phase. The instability is ascribed to the Marangoni effect and/or to liquid flow from the film drawn by diffusion of the solute.     

Kinetics and equilibria associated with the absorption and desorption of water and lithium chloride in an ethylene—vinyl alcohol copolymer

Sorption and desorption equilibria and kinetics for LiCl and H₂O in an ethylene—vinyl alcohol copolymer film containing 70 mole percent vinyl alcohol were investigated at 25°C. The swelling behavior of water in the polymer was characterized by vapor and liquid sorption experiments over a range of water activities. p]The effects of LiCl content on the water sorption kinetics and equilibria in the films are presented and discussed. The kinetics and mechanism of LiCl sorption have also been studied. The amount of salt sorbed into the polymeric films increases linearly with the salt concentration in the external aqueous solutions. Both the rate and the amount of sorbed water increase significantly as the LiCl content increases. p]The desorption of LiCl, previously sorbed into the polymer, was characterized for different salt loadings. The rate of fractional salt release is independent of LiCl concentration in the film. Initially, the salt release is controlled by the nearly constant-rate absorption of water. The salt release, at long times, lags behind the swelling-controlled water uptake, indicating that the salt release is not completely controlled by the water sorption and that diffusion in the swollen polymer matrix contributes significantly to the long term elution of LiCl. Independent thermal analysis experiments suggest the formation of a metal salt—poly(ethylene—vinyl alcohol) complex.     

Influence of a cationic polyelectrolyte on the inverse micellar region of the ternary system sulfobetaine/water/alcohol

The influence of the cationic polyelectrolyte poly(diallyldimethylammonium chloride) on structure formation in the inverse micellar region (L2 phase) of the ternary system 3 (N,N-dimethyldodecylammonio)propanesulfonate/alcohol/water has been investigated. Up to a polymer concentration in the aqueous phase of 10 wt %, an isotropic phase still exists. As the chain length of the alcohol component increases, the isotropic phase region is reduced and shifted in direction to the water corner. The isotropic polyelectrolyte-modified L2 phase of the heptanol-based microemulsion has been studied in much more detail by means of conductometric, rheological, and differential scanning calorimetry measurements. The polyelectrolyte-modified microemulsion phase shows a characteristic low shear viscosity and Newtonian flow behavior. The characteristic features of the nonpercolated microemulsion droplets are the low conductivity and the disappearance of bulk water. One can conclude from the experimental data that the individual nonpercolated polyelectrolyte-stuffed microemulsion droplets are approximately uniform in size. In addition, the area of the polyelectrolyte-modified inverse microemulsion phase with heptanol and octanol depends on the temperature. This means that the area of the L2 region can be increased by the temperature being increased from room temperature to 40 °C. This behavior can be explained by a change in the bending elasticity of the surface film induced by Coulombic interactions between the functional groups of the polyelectrolyte and the surfactant head groups. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 742–751, 2004     

Ion‐Transfer Electrochemistry of Rat Amylin at the Water–Organogel Microinterface Array and Its Selective Detection in a Protein Mixture

The behavior of proteins and polypeptides at electrified aqueous–organic interfaces is of benefit in label‐free detection strategies. In this work, rat amylin (or islet amyloid polypeptide) was studied at the interface formed between aqueous liquid and gelled organic phases. Amylin is a polypeptide that is co‐secreted with insulin from islet beta‐cells and is implicated in fibril formation. In this study, rat amylin was used, which does not undergo aggregation. The polypeptide underwent an interfacial transfer process, from water to the gelled organic phase, under applied potential stimulation. Cyclic voltammetry revealed steady‐state forward and peak‐shaped reverse voltammograms, which were consistent with diffusion‐controlled water‐to‐organic transfer and thin‐film stripping or desorptive back‐transfer. The diffusion‐controlled forward current was greater when amylin was present in an acidic aqueous phase than when it was present in an aqueous phase at physiological pH; this reflects the greater charge on the polypeptide under acidic conditions. The amylin transfer current was concentration dependent over the range 2–10 μM , at both acidic and physiological pH. At physiological pH, amylin was selectively detected in the presence of a protein mixture, which illustrated the bioanalytical possibilities for this electrochemical behavior.