Cr3＋／MgF2氟化催化剂的制备及其对合成二氟甲烷反应的催化性能

 用混合法制备了Cr3＋／MgF2氟化催化剂，以CH2F2（HFC－32）的合成为目标反应考察了制备条件对催化剂性能的影响．结果表明，在N2气氛中焙烧的催化剂的比表面积及其氟化活性高于空气中焙烧的催化剂；在300～500℃的N2气氛中焙烧时，催化剂的活性随焙烧温度升高而降低；随活化温度的升高，催化剂活性增高，在350℃达最大值；Cr含量为10％时，催化剂的孔容、比表面积和活性最大．DSC和TGA结果表明，载体MgF2在500℃以下未发生热分解和晶形转变，Cr3＋／MgF2催化剂也具有较高的稳定性．再生性能、使用寿命及对CF3CH2F（HFC－134a）合成的催化活性评价实验表明，Cr3＋／MgF2催化剂在使用300h后仍保 持较高的活性，且易于再生．     

还原温度对超细K－Co－Mo催化剂合成低碳醇性能的影响

 用溶胶－凝胶法合成了K－Co－Mo催化剂．样品经不同温度还原后，用于低碳醇的合成．XRD和HRTEM结果表明，样品是超细粒子，粒子尺寸为2～5nm．考察了催化剂的还原温度和反应条件对催化剂性能的影响．实验结果表明，还原温度对催化剂的活性有较大的影响，最佳还原温度为500℃．最佳反应温度范围为310～330℃．升高压力和空速可以提高醇的收率和选择性．在空速14400h－1，压力6．0MPa和温度310℃的条件下，醇的选择性为55．8％，收率为520．0g／（kg·h），MeOH／C2＋OH为0．27．催化剂稳定性良好，在200h的寿命实验中，活性基本不变．与文献中催化剂相比，超细K－Co－Mo催化剂对合成醇具有较高的活性和选择性，尤其是对C2＋OH的合成明显高于其他合成醇催化剂体系．     

Co/SiO2催化剂合成重质烃的反应性能

 对近期筛选出的一种重质烃合成反应性能良好的Co／SiO2催化剂进行了500h的寿命试验,考察了在不同反应温度、压力和空速条件下催化剂的反应性能．结果表明,随着反应的进行,催化剂合成重质烃的选择性基本保持不变,但催化剂的活性缓慢下降;经原位再生后,催化剂活性可基本恢复到原来的水平．烃产物主要由烷烃组成,C5＋中烯烃仅占2．25％,产物主要集中在C12～C20馏分段,水相产物中含3．56％～6．56％的有机含氧化合物,其中主要是低碳醇．     

SO_4~(2-)/ZrO_2催化剂上正丁烷异构化反应

考察了活化温度、反应温度、空速、Ｈ２／Ｃ４比和载Ｐｔ对ＳＯ２－４／ＺｒＯ２催化剂的正丁烷异构化反应活性和稳定性的影响．较高的Ｈ２／Ｃ４比可提高ＳＯ２－４／ＺｒＯ２催化剂的稳定性和稳态活性．催化剂负载Ｐｔ后，可降低反应原料中的Ｈ２／Ｃ４比．积炭是造成反应初始阶段催化剂迅速失活的主要原因，经烧炭再生以后这部分失活可以完全恢复     

水热处理对纳米HZSM－5沸石酸性质及其降低汽油烯烃性能的影响

 采用水蒸气和碱性氨水蒸气在500℃下对纳米HZSM－5沸石催化剂进行了水热处理改性，并用XRD，IR，NH3－TPD和XRF对催化剂进行了表征．以降低FCC汽油（≤70℃馏分）烯烃含量为探针反应，考察了不同水热处理介质对催化剂酸性质和催化性能的影响．结果表明，经不同介质水热处理后，纳米HZSM－5沸石中约10％的Al2O3被脱除，总酸量降低，导致积炭失活的强酸中心明显减少；不同水热处理介质对催化剂的总酸量没有明显影响，而对酸中心类型分布的影响较大．水热处理改性使催化剂活性的稳定性明显改善，初始活性降低．同时，水热处理改性降低了催化剂对芳构化反应的催化活性，提高了对异构化反应的催化活性．采用氨水（0．5mol／L）蒸气处理的纳米HZSM－5催化剂其降烯烃催化活性更为稳定．在给定的反应条件下，FCC汽油的烯烃含量（φ）由65．9％降低到约26％，产物中烯烃、芳烃（主要是C7～C9芳烃）和烷烃含量分别保持在25％，19％和55％左右，辛烷值基本不变．     

Pd-SiW12/SiO2催化剂上乙烯直接氧化制乙酸的反应机理

 利用积分反应器和微分反应器对Pd－SiW12／SiO2催化剂上乙烯直接氧化生成乙酸的反应机理进行了探讨．乙烯在积分反应中氧化的主要产物为乙酸（选择性为77．6％），很少生成乙醛（选择性仅为8．1％）；而在微分反应中氧化的主要产物是乙醛（选择性为98．4％）．在微分反应中分别以乙醛和乙醇为主反应物时，乙醛氧化完全生成乙酸，选择性为100％，而乙醇氧化生成乙酸的选择性低于0．15％．可以认为，在Pd－SiW12／SiO2催化剂上，水蒸气存在下乙烯主要经由中间物乙醛而生成乙酸．通过对含有不同组分和不同还原条件处理的催化剂活性的比较，认为目的反应主要发生在Pd与SiW12相互接触的部位，催化剂中的Pd0是活性Pd物种的主要形态．     

CsCuHPVAsMoO杂多化合物对异丁烯选择性氧化反应的催化性能

 用组合法合成了CsCuHPVAsMoO系列杂多化合物催化剂，并采用FT－IR，H2－TPR，NH3－TPD和TG－DTA等方法对催化剂进行了表征．在自制固定床反应器中对异丁烯进行选择性氧化，考察了Cs，Cu和As含量、催化剂焙烧温度及反应条件对催化剂催化性能的影响．结果表明，Cs的引入有利于提高催化剂的选择性；Cu和As的引入在提高催化剂活性的同时，也提高了催化剂的选择性；当焙烧温度为340℃时，催化剂的活性和选择性最高．组成为Cs0．1Cu0．2HxPVAs0．2Mo10Oy的催化剂对异丁烯具有很强的选择性氧化能力，在最佳反应条件下，甲基丙烯酸、甲基丙烯醛和乙酸的收率分别可达52．84％，12．05％和18．21％．     

合成气制低碳烯烃用Fe／AC催化剂的制备及性能表征

 研究了以活性炭（AC）作为载体制备的铁基催化剂，通过对不同铁盐、活性炭和助剂的筛选，研制出对合成气转化为低碳烯烃具有高活性和高选择性的催化剂．对反应前及反应过程中催化剂体相结构的XRD测试结果表明，Fe－Cu－K／AC催化剂在反应前主要由α－Fe，Fe3O4和Cu0组成，经合成气反应后主要由α－Fe，Fe5C2，Fe7C3，Cu0和K2O组成．Fe－Mn－K／AC催化剂的晶体结构主要以Fe嵌入MnO中形成的（Fe，Mn）O结构存在．实验中得出的α－Fe，FexCy及（Fe，Mn）O与激光热解法制备的催化剂的的晶体结构相似．对催化剂的制备方法进行了筛选，考察了不同助剂Cu，Mn，Si和K等元素对催化剂性能的影响．结果表明，以草酸铁为铁源，椰壳炭为载体制备的Fe－Mn－K／AC催化剂的催化效果最佳，在空速600h－1，压力1．5MPa和温度320℃条件下，CO转化率可达97．4％，C＝2～C＝4选择性可达68．0％．     

酸化粘土负载ZnCl2催化剂的制备及其对苯苄基化反应的催化性能

 以酸化粘土矿物蒙脱土为载体，采用浸渍蒸发法制备了蒙脱土负载的ZnCl2固体酸催化剂，并以苯与苄基氯的苄基化反应评价了其催化性能．考察了催化剂制备条件、苄基化反应条件和催化剂的再生性能，比较了负载前后催化剂的活性．利用XRD，TG－DTA和FT－IR等技术对催化剂的结构和表面酸性进行了表征．结果表明，较适宜的催化剂制备条件为：原矿土经30％硫酸酸化处理4h，ZnCl2负载量为2．0mmol／g，催化剂于250～350℃焙烧活化．过量的苯和较高的反应温度有利于提高苄基氯的转化率，催化剂与苄基氯的用量比为1．5g／mol．产物二苯甲烷的收率最高可达83．5％．表征分析表明，蒙脱土酸化处理后层状结构遭到破坏，比表面积增大，负载和活化处理使ZnCl2与蒙脱土载体的羟基之间发生了化学键合，提高了蒙脱土表面的总酸量，从而提高了催化剂的催化活性．     

甲烷部分氧化反应的镧改性Ni／γ-Al2O3催化剂研究

采用Na2CO3-NaOH为沉淀剂共沉淀制备La改性的镍基氧化铝催化剂，对甲烷部分氧化反应表现出高的活性和选择性。La的加入有效地抑制了大颗粒的NiAl2O3的形成，保持了相当高比例的活性镍组分，提高了催化剂的催化活性；而且加入La可以抑制氢氧化铝或氧化铝的物相转变，提高载体稳定性。活性测试结果表明共沉淀制备的20％镍含量的800℃焙烧La改性镍基氧化铝催化剂在800℃反应温度下XCH4，Sco和SH2分别达到100％，95．95％，99．87％，且催化剂在15h内活性几乎没有下降，显示了很好的催化性能和稳定性。通过对不同温度还原的催化剂的活性测试和TPR表征，得出无定型NiAl2O。还原出的Ni^0是甲烷部分氧化反应的主要活性组分。     

Sc2MgGa2 and Y2MgGa2

Scandium magnesium gallide, Sc₂MgGa₂, and yttrium magnesium gallide, Y₂MgGa₂, were synthesized from the corresponding elements by heating under an argon atmosphere in an induction furnace. These intermetallic compounds crystallize in the tetragonal Mo₂FeB₂‐type structure. All three crystallographically unique atoms occupy special positions and the site symmetries of (Sc/Y, Ga) and Mg are m2m and 4/m, respectively. The coordinations around Sc/Y, Mg and Ga are pentagonal (Sc/Y), tetragonal (Mg) and triangular (Ga) prisms, with four (Mg) or three (Ga) additional capping atoms leading to the coordination numbers [10], [8+4] and [6+3], respectively. The crystal structure of Sc₂MgGa₂ was determined from single‐crystal diffraction intensities and the isostructural Y₂MgGa₂ was identified from powder diffraction data.     

Zur Kenntnis der Dialkalimetalldichalkogenide β-Na2S2, K2S2, α-Rb2S2, β-Rb2S2, K2Se2, Rb2Se2, α-K2Te2, β-K2Te2 und Rb2Te2

On Dialkali Metal Dichalcogenides β-Na₂S₂, K₂S₂, α-Rb₂S₂, β-Rb₂S₂, K₂Se₂, Rb₂Se₂, α-K₂Te₂, β-K₂Te₂ and Rb₂Te₂ The first presentation of pure samples of α- and β-Rb₂S₂, α- and β-K₂Te₂, and Rb₂Te₂ is described. Using single crystals of K₂S₂ and K₂Se₂, received by ammonothermal synthesis, the structure of the Na₂O₂ type and by using single crystals of β-Na₂S₂ and β-K₂Te₂ the Li₂O₂ type structure will be refined. By combined investigations with temperature-dependent Guinier-, neutron diffraction-, thermal analysis, and Raman-spectroscopy the nature of the monotropic phase transition from the Na₂O₂ type to the Li₂O₂ type will be explained by means of the examples α-/β-Na₂S₂ and α-/β-K₂Te₂. A further case of dimorphic condition as well as the monotropic phase transition of α- and β-Rb₂S₂ is presented. The existing areas of the structure fields of the dialkali metal dichalcogenides are limited by the model of the polar covalence.     

Crystal Structures of [Bu2Sn(O2PPh2)2], [Ph2Sn(O2PPh2)2], and [PhClSn(O2PPh2)OMe]2. Raman Spectra of [Ph2Sn(O2PPh2)2] and [PhClSn(O2PPh2)OMe]2

[(n‐Bu)₂Sn(O₂PPh₂)₂] ( 1 ), and [Ph₂Sn(O₂PPh₂)₂] ( 2 ) have been synthesized by the reactions of R₂SnCl₂ (R=n‐Bu, Ph) with HO₂PPh₂ in Methanol. From the reaction of Ph₂SnCl₂ with diphenylphosphinic acid a third product [PhClSn(O₂PPh₂)OMe]₂ ( 3 ) could be isolated. X‐ray diffraction studies show 1 to crystallize in the monoclinic space group P2₁/c with a = 1303.7(1) pm, b = 2286.9(2) pm, c = 1063.1(1) pm, β = 94.383(6)°, and Z = 4. 2 crystallizes triclinic in the space group , the cell parameters being a = 1293.2(2) pm, b = 1478.5(4) pm, c = 1507.2(3) pm, α = 98.86(3)°, β = 109.63(2)°, γ = 114.88(2)°, and Z = 2. Both compounds form arrays of eight‐membered rings (SnOPO)₂ linked at the tin atoms to form chains of infinite length. The dimer 3 consists of a like ring, in which the tin atoms are bridged by methoxo groups. It crystallizes triclinic in space group with a = 946.4(1) pm, b = 963.7(1) pm, c = 1174.2(1) pm, α = 82.495(6)°, β = 66.451(6)°, γ = 74.922(6)°, and Z = 1 for the dimer. The Raman spectra of 2 and 3 are given and discussed.     

Thermal decomposition of Me3SnO2PCl2, Me2Sn(O2PCl2)2 and Ph3SnO2PCl2

TG and DTA studies on Me₃SnO₂PCl₂, Me₂Sn(O₂PCl₂)₂ and Ph₃SnO₂PCl₂ were carried out under dynamic argon atmosphere. The results show that the decomposition proceeds in different stages leading to the formation of Sn₃(PO₄)₂ as a stable product. This compound was characterized by IR spectroscopy. Decomposition schemes involving reductive elimination reactions were proposed.     

Electrochemical study of (NEt4)2Cl2FeS2MoS2 and (NEt4)2Cl2FeS2MoS2FeCl2

Summary The ability of [MoS₄]^2–, anions to be used as ligands for transition metal ions has been widely demonstrated, especially with Fe²⁺. The present study has been restricted to linear complexes such as (NEt₄)₂ [Cl₂FeS₂MoS₂] and (NEt₄)₂[Cl₂FeS₂MoS₂FeCl₂]. Their electrochemical properties are described: upon electrochemical reduction, these compounds yield MoS₂, as a black precipitate, and an iron complex in solution, assumed to be [SFeCl₂]^2–. The electrochemical reduction goes through two electron transfers, coupled with the breakdown of the molecular skeleton: a DISPl and an ECE mechanism. Depending on the solvent, the following equilibrium may be observed: [Cl₄Fe₂MoS₄]^2–[Cl₂FeMoS₄]^2–+FeCl₂. The equilibrium constant, K_D, was evaluated by differential pulse polarography. K_D is tightly related to the donor number of the solvent.     

The alkali hypophosphites KH2PO2, RbH2PO2 and CsH2PO2

The structures of the hypophosphites KH₂PO₂ (potassium hypophosphite), RbH₂PO₂ (rubidium hypophosphite) and CsH₂PO₂ (caesium hypophosphite) have been determined by single‐crystal X‐ray diffraction. The structures consist of layers of alkali cations and hypophosphite anions, with the latter bridging four cations within the same layer. The Rb and Cs hypophosphites are isomorphous.     

Formal [(2+2)+2] and [(2+2)+(2+2)] nonconjugated dienediyne cascade cycloadditions

[reaction: see text] Fluoranthene 2 and heptacycle 3 are easily accessible from the reaction of diyne 1 and norbornadiene (NBD) in the presence of the rhodium catalyst. The unusual [(2+2)+(2+2)] adduct 3 was confirmed by the X-ray crystal structure analysis.