Thienoisoindigo‐based small molecules and narrow bandgap polymers synthesized via C–H direct arylation coupling

Thienoisoindigo (TIIG) has emerged as an attractive building block for high‐performance organic optoelectronic devices. Here we report the first synthesis of a series of π‐conjugated TIIG‐based small molecules and alternating copolymers via direct C–H arylation, which enables the efficient synthesis without use of flammable and toxic orgametallic reagents in fewer steps compared Suzuki and Stille coupling. The direct arylation coupling between TIIG and two respective mono‐bromo aryl reactants clearly shows that the α‐H is more reactive than the β‐H in the thiophene unit of TIIG. The high regioselectivity of TIIG monomer warrants the successful synthesis of high‐quality alternating copolymers with minimal structural defects. PTIIG‐BT polymer synthesized via direct arylation polymerization (DAP) showed comparable molecular weight and hole mobility than the same polymer previously synthesized via Suzuki coupling. Moreover, the two new polymers (PTIIG‐TF and PTIIG‐2FBT) synthesized via DAP showed hole mobility up to 10^?3 cm² V^?1 s^?1 in FET devices fabricated and tested under ambient conditions. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2015–2031     

Novel triarylamine‐based alternating conjugated polymer with high hole mobility: Synthesis,electro‐optical,and electronic properties

Novel bi‐triphenylamine‐containing aromatic dibromide M3 , N,N‐bis(4‐bromophenyl)‐N′,N′‐dipheny‐l,4‐phenylenediamine, was successfully synthesized. The novel conjugated polymer P1 having number‐average molecular weight of 1.31 × 10⁴ was prepared via Suzuki coupling from the dibromide M3 and 9,9‐dioctylfluorene‐2,7‐diboronic acid bis(1,3‐propanediol) ester. Polymer P1 had excellent thermal stability associated with a high glass‐transition temperature (T_g = 141 °C). The hole‐transporting and UV‐vis‐near‐infrared electrochromic properties were examined by electrochemical and spectroelectrochemical methods. Cyclic voltammograms of the conjugated polymer films cast onto indium‐tin oxide‐coated glass substrates exhibited two reversible oxidation redox couples at E_1/2 values of 0.73 and 1.13 V versus Ag/Ag⁺ in acetonitrile solution. The hole mobility of the conjugated polymer P1 revealed ～10^?3 cm² V^?1 s^?1, which is much higher than that of other conjugated polymer systems. The observed UV‐vis‐near‐infrared absorption change in the conjugated polymer film P1 at applied potentials ranging from 0.00 to 1.23 V are fully reversible and associated with strong color changes from pale yellowish in its neutral form to green and blue in its oxidized form. Using a combination of experimental study and theoretical investigation, we proposed an oxidation mechanism based on molecular orbital theory, which explains the cyclic voltammetry experimental results well. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Development of solution‐dispersible hyperbranched conjugated polymer nanoparticles for Fe3+ fluorescent detection and their application in logic gate

Solution‐dispersible hyperbranched conjugated polymer nanoparticles (FT‐HBCPNs) consist of an intrinsic crosslinked rigid skeleton structure of both 9,9‐dihexyl‐fluorene and triphenylamine repeating units, and are synthesized via the miniemulsion Suzuki polymerization, and FT‐HBCPNs for highly selective and sensitive Fe³⁺ fluorescent detection and their application in logic gate at molecular level are successfully developed. FT‐HBCPNs with an average particle size of 10.6 nm can disperse in common organic solvents. FT‐HBCPNs show high selectivity and sensitivity for Fe³⁺ over other commonly co‐existent metal ions in THF solution with a detection limit of 3.65 × 10^?8 mol L^?1. Furthermore, homogeneous transparent thin films of FT‐HBCPNs developed by a simple spin‐coating method can be reversibly quenched by Fe³⁺ with a detection limit of 3.09 × 10^?7 mol L^?1. Using Fe³⁺ and EDTA as chemical inputs and the fluorescence intensity signal as outputs, FT‐HBCPNs films can be utilized as a logic gate at molecular level. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 3694–3700     

Synthesis and characterization of chiral polymer complexes incorporating polybinaphthyls,bipyridine, and Eu(III)

Chiral conjugated polymers P‐1 and P‐2 were synthesized by the polymerization of (S)‐3,3′‐diiodo‐2,2′‐bisbutoxy‐1,1′‐binaphthyl and (S)‐6,6′‐dibromo‐2,2′‐bisbutoxy‐1,1′‐binaphthyl, respectively, with 5,5′‐divinyl‐2,2′‐bipyridine through a Heck cross‐coupling reaction. Chiral polymer complexes P‐C‐1 and P‐C‐2 were obtained by the bipyridine chelating coordination of P‐1 and P‐2 with Eu(TTA)₃·2H₂O (where TTA is 2‐thenoyltrifluoroacetonate). Polymers P‐1 and P‐2 and polymer complexes P‐C‐1 and P‐C‐2 exhibited intense circular dichroism signals, with negative and positive Cotton effects in their circular dichroism spectra. The chiral polymers showed strong green‐blue fluorescence because of the efficient energy migration from the extended π‐electronic structure of the conjugated polymer main to the chiral binaphthyl core. The chiral polymer complexes could have not only polymer fluorescence but also the characteristic fluorescence of Eu(III) (⁵D₀→⁷F₂) at a different excited wavelength. These kinds of chiral polymer complexes incorporating polybinaphthyls, bipyridine, and Eu(III) moieties are expected to provide an understanding of the relationship between the structure and properties of chiral polymer complexes. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 650–660, 2007     

Effect of reaction conditions on the molecular weight and polydispersity of linear poly(arylene ether phosphine oxide)s prepared from an AB monomer

A thorough study of the polymerization behavior of 4‐fluoro‐4′‐hydroxytriphenyl‐phosphine oxide, 2 , under nucleophilic aromatic substitution reactions has been carried out. The synthesis of 2 was achieved in excellent yields by the reaction of bis(4‐fluorophenyl)phenylphosphine oxide, 1 , with one equivalent of potassium hydroxide in DMSO/water. The structure and purity of 2 were confirmed via ¹H, ¹³C, and ³¹P NMR spectroscopy along with elemental analysis. Polymerization reactions of 2 in NMP or DMSO at 180 °C provided the corresponding linear poly(arylene ether phosphine oxide)s, PAEPOs, with number average molecular weights, M_n, ranging from 11,700 to 36,500 Da. All of the polymer samples were completely soluble in chloroform, tetrahydrofuran, DMSO, NMP, and DMAc. The polymerization reactions were accompanied by a competing intramolecular process that resulted in the formation of cyclic oligomeric species that were removed via a final precipitation from methanol. Analysis using ³¹P NMR spectroscopy and size exclusion chromatography (SEC) confirmed that the majority of the lower molecular weight cyclic species were removed via this process. The polymer samples formed tough films when chloroform solutions were slowly evaporated on a glass slide. The PAEPO samples prepared in this study exhibited excellent thermal stability with T_d (5%) values between 503 and 542 in air while the glass transition temperatures ranged from 223 to 237 °C. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2099–2106, 2006     

Efficient fabrication of polymer nanoparticles via sonogashira cross‐linking of linear polymers in dilute solution

The synthesis of single‐chain nanoparticles by palladium‐catalyzed Sonogashira coupling between a terminal alkyne and a di‐halo aryl cross‐linker is reported. Statistical copolymers with trimethylsilyl protected alkyne groups pendent to the linear methacrylate back bones were synthesized using reversible addition‐fragmentation chain transfer polymerization post polymerization de‐protection providing terminal alkyne functionalized linear polymer chains. These linear polymer chains were intramolecularly cross‐linked via bifunctional cross‐linkers. The resulting well‐defined covalently bonded nanoparticles were characterized via triple‐detection size exclusion chromatography where MALS detector provided molecular weight information and viscometric detection characterizes particle size and conformations. The particle size could be readily tuned through polymer molecular weight and by degree of cross‐linking. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 209–217     

Synthesis and properties of new orange red light‐emitting hyperbranched and linear polymers derived from 3,5‐dicyano‐2,4,6‐tristyrylpyridine

Two new orange red light‐emitting hyperbranched and linear polymers, poly(pyridine phenylene)s P1 and P2, were prepared by the Heck coupling reaction. In particular, an A₂ + B₃ approach was developed to synthesize conjugated hyperbranched polymer P2 via one‐pot polycondensation. The polymers were characterized by NMR, Fourier transform infrared, ultraviolet–visible, and elemental analysis. They showed excellent solubility in common solvents such as tetrahydrofuran, CH₂Cl₂, CHCl₃, and N,N‐dimethylformamide and had high molecular weights (up to 6.1 × 10⁵ and 5.8 × 10⁵). Cyclic voltammetry studies revealed that P2 had a low‐lying lowest unoccupied molecular orbital energy level of ?3.22 eV and a highest occupied molecular orbital energy level of ?5.43 eV. The thin film of P2 emitted strong orange‐red photoluminescence at 595 nm. A double‐layer light‐emitting diode fabricated with the configuration of indium tin oxide/P2/tris(8‐hydroxy‐quinoline)aluminum/Al emitted orange‐red light at 599 nm, with a brightness of 662 cd/m² at 7 V and a turn‐on voltage of 4.0 V; its external quantum efficiency was calculated to be 0.19% at 130.61 mA/cm². This indicated that this new electroluminescent polymer (P2) based on 3,5‐dicyano‐2,4,6‐tristyrylpyridine could possibly be used as an orange‐red emitter in polymer light‐emitting displays. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 493–504, 2005     

From single‐chain folding to polymer nanoparticles via intramolecular quadruple hydrogen‐bonding interaction

Single‐chain folding via intramolecular noncovalent interaction is regarded as a facile mimicry of biomacromolecules. Single‐chain folding and intramolecular crosslinking is also an effective method to prepare polymer nanoparticles. In this study, poly(methyl methacrylate‐co?2‐ureido‐5‐deazapterines functionalized ethylene methacrylate) (P(MMA‐co‐EMA‐DeAP)) is synthesized via free radical polymerization. The single‐chain folding of P(MMA‐co‐EMA‐DeAP) and the formation of the nanoparticles in diluted solution (concentration <0.005 mg/mL) are achieved via supramolecular interaction and intramolecular collapsing during the disruption‐reformation process of the hydrogen bonding triggered by water. The size and the morphology of the nanoparticles are characterized by dynamic light scattering, transmission electron microscope, and atomic force microscope. The results show that the size of the nanoparticles depends on the molecular weight of the polymer and the loading of 2‐ureido‐5‐deazapterines functionalized ethylene methacrylate (EMA‐DeAP) on the polymer backbone. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1832–1840     

Thermoresponsive poly(ionic liquid): Controllable RAFT synthesis,thermoresponse, and application in dispersion RAFT polymerization

The thermoresponsive poly(ionic liquid) of poly[1‐(4‐vinylbenzyl)‐3‐methylimidozolium tetrafluoroborate] trithiocarbonate (P[VBMI][BF₄]‐TTC) showing the soluble‐to‐insoluble phase transition in the methanol/water mixture at the upper critical solution temperature (UCST) was synthesized by solution RAFT polymerization and the synthesized P[VBMI][BF₄]‐TTC was employed as macro‐RAFT agent to mediate the RAFT polymerization under dispersion condition to afford the thermoresponsive diblock copolymer nanoparticles of poly[1‐(4‐vinylbenzyl)‐3‐methylimidozolium tetrafluoroborate]‐b‐polystyrene (P[VBMI][BF₄]‐b‐PS). The controllable solution RAFT polymerization was achieved as indicated by the linearly increasing polymer molecular weight with the monomer conversion and the narrow molecular weight distribution. The P[VBMI][BF₄]‐TTC macro‐RAFT agent mediated dispersion polymerization afforded the P[VBMI][BF₄]‐b‐PS nanoparticles, the size of which was uncorrelated with the polymerization degree of the P[VBMI][BF₄] block. Several parameters including the polymerization degree, the polymer concentration and the water content in the solvent of the methanol/water mixture were found to be correlated with the UCST of the poly(ionic liquid). The synthesized poly(ionic liquid) is believed to be a new thermos‐responsive polymer and will be useful in material science. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 945–954     

High performance polymer field‐effect transistors based on polythiophene derivative with conjugated side chain

Poly(3‐[2‐(5‐hexyl‐2‐thienyl) ethenyl]‐2,2′‐bithiophene) ( P2 , see Scheme 1 ) with conjugated thienylvinyl side chain was synthesized by copolymerization of the thiophene units with and without conjugated side chain with Pd‐catalyzed Stille coupling method. For comparison, P1 with the hexyl side chain instead of conjugated side chain was also synthesized. P2 film shows broad absorption in the visible region with absorption edge at about 700 nm. The solution‐processed polymer field‐effect transistors were fabricated and characterized with bottom gate/top contact geometry. The organic field‐effect transistors (OFET) based on P2 showed an average hole mobility of about 0.034 cm²/Vs (the highest value reached 0.061 cm²/Vs) upon annealing at about 180 °C for 30 min, with a threshold voltage of ?1.15 V and an on/off ratio of 10⁴ with n‐octadecyltrichlorosilane (OTS) modified SiO₂ substrate. In comparison, the OFET based on P1 displayed a hole mobility of 8.9 × 10^–4 cm²/Vs and an on/off ratio of 10⁴ with OTS modified SiO₂ substrate. The results indicate that the polythiophene derivative with conjugated thienylvinyl side chain is a promising polymer for the application in polymer field‐effect transistors. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5304–5312, 2009     

Poly(thienylene‐vinylene‐thienylene) with cyano substituent: Synthesis and application in field‐effect transistor and polymer solar cell

A novel conjugated polymer, poly(thienylene‐vinylene‐thienylene) with cyano substituent ( CN‐PTVT ) was synthesized via Stille coupling for the application in air stable field‐effect transistor and polymer solar cell. The polymer was characterized by ¹H NMR, elemental analysis, UV‐vis absorption and photoluminescence spectroscopy, TGA, cyclic voltammetry and XRD analysis. CN‐PTVT exhibits a good thermal stability with 5% weight loss at 306 °C. The FET hole mobility of the polymer reached 5.9 × 10^?3 cm² V^?1 s^?1 with I_on/I_off ratio of 4.9 × 10⁴, which is one of the highest performance among the air‐stable amorphous polymers. The polymer solar cell based on CN‐PTVT as donor and PCBM as acceptor shows a relatively high open‐circuit voltage of 0.82 V and a power conversion efficiency of 0.3% under the illumination of AM1.5, 100 mW/cm². © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 4028–4036, 2009     

Bipyridinophane‐containing conjugated polymers modulated with an intramolecular aromatic C?H/π interaction

Bipyridinophane–fluorene conjugated copolymers have been synthesized via Suzuki and Heck coupling reactions from 5,8‐dibromo‐2,11‐dithia[3]paracyclo[3](4,4′)‐2,2′‐bipyridinophane and suitable fluorene precursors. Poly[2,7‐(9,9‐dihexylfluorene)‐co‐alt‐5,8‐(2,11‐dithia[3]paracyclo[3](4,4′)‐2,2′‐bipyridinophane)] ( P7 ) exhibits large absorption and emission redshifts of 20 and 34 nm, respectively, with respect to its planar reference polymer Poly[2,7‐(9,9‐dihexylfluorene)‐co‐alt‐1,4‐(2,5‐dimethylbenzene)] ( P11 ), which bears the same polymer backbone as P7 . These spectral shifts originate from intramolecular aromatic C? H/π interactions, which are evidenced by ultraviolet–visible and ¹H NMR spectra as well as X‐ray single‐crystal structural analysis. However, the effect of the intramolecular aromatic C? H/π interactions on the spectral shift in poly[9,9‐dihexylfluorene‐2,7‐yleneethynylene‐co‐alt‐5,8‐(2,11‐dithia[3]paracyclo[3](4,4′)‐2,2′‐bipyridinophane)] ( P10 ) is much weaker. Most interestingly, the quenching behaviors of these two conjugated polymers are largely dependent on the polymer backbone. For example, the fluorescence of P7 is efficiently quenched by Cu²⁺, Co²⁺, Ni²⁺, Zn²⁺, Mn²⁺, and Ag⁺ ions. In contrast, only Cu²⁺, Co²⁺, and Ni²⁺ ions can partially quench the fluorescence of P10 , but much less efficiently than the fluorescence of P7 . The static Stern–Volmer quenching constants of Cu²⁺, Co²⁺, and Ni²⁺ ions toward P7 are of the order of 10⁶ M^?1, being 1300, 2500, and 37,300 times larger than those of P10 , respectively. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4154–4164, 2006     

Synthesis and characterization of indenofluorene‐based copolymers containing 2,5‐bis(2‐thienyl)‐N‐arylpyrrole for bulk heterojunction solar cells and polymer light‐emitting diodes

Two novel alternating π‐conjugated copolymers, poly[2,8‐(6,6′,12,12′‐tetraoctyl‐6,12‐dihydroindeno‐[1,2b]fluorene‐ alt‐5(1‐(2,6‐diisopropylphenyl)‐2,5‐di(2‐thienyl)pyrrole) ( P1 ) and poly[2,8‐(6,6′,12,12′‐tetraoctyl‐6,12‐dihydroindeno‐[1,2b]fluorene‐ alt‐5(1‐(p‐octylphenyl)‐2,5‐di(2‐thienyl)pyrrole) ( P2 ), were synthesized via the Suzuki coupling method and their optoelectronic properties were investigated. The resulting polymers P1 and P2 were completely soluble in various common organic solvents and their weight‐average molecular weights (M_w) were 5.66 × 10⁴ (polydispersity: 1.97) and 2.13× 10⁴ (polydispersity: 1.54), respectively. Bulk heterojunction (BHJ) solar cells were fabricated in ITO/PEDOT:PSS/polymer:PC₇₀BM(1:5)/TiO_x/Al configurations. The BHJ solar cell with P1 :PC₇₀BM (1:5) has a power conversion efficiency (PCE) of 1.12% (J_sc= 3.39 mA/cm², V_oc= 0.67 V, FF = 49.31%), measured using AM 1.5 G solar simulator at 100 mW/cm² light illumination. We fabricated polymer light‐emitting diodes (PLEDs) in ITO/PEDOT:PSS/emitting polymer:polyethylene glycol (PEG)/Ba/Al configurations. The electroluminescence (EL) maxima of the fabricated PLEDs varied from 526 nm to 556 nm depending on the ratio of the polymer to PEG. The turn‐on voltages of the PLEDs were in the range of 3–8 V depending on the ratio of the polymer to PEG, and the maximum brightness and luminance efficiency were 2103 cd/m² and 0.37 cd/A at 12 V, respectively. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3169–3177, 2010     

Prepolymerization and postpolymerization functionalization approaches to fluorescent conjugated carbazole‐based glycopolymers via “click chemistry”

Facile prepolymerization and postpolymerization functionalization approaches to prepare well‐defined fluorescent conjugated glycopolymers through Cu(I)‐catalyzed azide/alkyne “Click” ligation were explored. Two well‐defined carbazole‐based fluorescent conjugated glycopolymers were readily synthesized based on these strategies and characterized by ¹H NMR, ¹³C NMR, IR spectra, and UV‐vis spectra. The “Click” ligation offers a very effective conjugation method to covalently attach carbohydrate residues to fluorescent conjugated polymers. In addition, the studies of carbohydrate–lectin interactions were performed by titration of concanavalin A (Con A) to D ‐glucose‐bearing poly(anthracene‐alt‐carbazole) copolymer P‐2 resulting in significant fluorescence quenching of the polymer due to carbohydrate–lectin interactions. When peanut agglutinin (PNA) was added, no distinct change in the fluorescent properties of P‐2 was observed. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2948–2957, 2009     

Sulfonated poly(meta‐phenylene isophthalamide)s as proton exchange membranes

Random and block sulfonated poly(meta‐phenylene isopthalamide)s as proton exchange membranes were synthesized through the Higashi‐Yamazaki phosphorylation method. Polymers with different degrees of sulfonation from 40 to 100 mol percent were prepared by adjusting the molar feed ratio of 5‐sulfoisophthalic acid sodium salt (SIPA) and isophthalic acid (IPA) in the reaction with meta‐phenylene diamine. Creasable polymer films were obtained by casting DMSO polymer solutions and the membrane films could be exchanged to the proton form in strong acid. ¹H NMR spectroscopy and titration confirmed the degree of sulfonation. Thermogravimetric analysis demonstrated good thermal stabilities with 5% weight loss greater than 380 °C. The copolymers with low degrees of sulfonation (DS = 40 mol %) exhibited low water uptake (water uptake < 17 wt %) at room temperature. A segmented multiblock copolymer prepared by preforming a sulfonated block showed lower water uptake at high temperatures than the random polymer with the same DS of 40 mol % and displayed stability in water up to 80 °C. Both random and block copolymers showed higher proton conductivities at high temperature than that of Nafion‐117 under 95% relative humidity. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2582–2592     

Control of vertical distribution of thiophene‐based copolymers containing 4,7‐Dithien‐2‐yl‐benzo[C][1,2,5]thiadiazole and 3,6‐Dithien‐2‐yl‐pyrrolo[3,4‐C]pyrrole‐1,4(2H,5H)‐dione as Side Groups for Photovoltaics

Four new D—A type copolymers with 2D‐conjugated side‐chain identified PfToBT, PbToBT, PfTDPP and PbTDPP, containing two acceptors 4,7‐dithien‐2‐yl‐benzo[c][1,2,5]thiadiazole (DTBT), and diketopyrrolopyrrole (DPP) linked by thiophene donors, are obtained using Pd‐catalyzed Stille‐coupling reaction. These polymers show a broad visible‐near‐infrared absorption band (E_g = 1.79–1.66 eV) and possess a relatively low‐lying HOMO level at ?5.34 to ?5.12 eV. All the polymer:PC₇₀BM blend films showed edge‐on structure and have similar d_π‐spacing values. According to the structure of conjugated side‐chain, the vertical distributions of polymer chains and PC₇₀BM within the BHJ (bulk heterojunction) were different. When DPP used as an acceptor, conjugated side chains of the polymer coexisted with PC₇₀BM in same position. The BHJ film prepared from PfToBT, PbToBT had a discontinuous network between polymer and PC₇₀BM, whereas films from PfTDPP and PbTDPP formed continuous and evenly distributed network between them. This optimized vertical morphology promotes hole transport along respective pathways of polymers and fullerenes in the vertical direction, leading to high J_SC. PbTDPP shows PCE up to 2.9% (Jsc of 9.4 mA/cm², Voc of 0.68 V, and FF of 0.44). © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2746–2759     

Size‐controlled synthesis of soluble‐conjugated microporous polymer nanoparticles through sonogashira polycondensation in confined nanoreactors

Soluble conjugated polymeric nanoparticles were synthesized through Sonogashira polycondensation between different combinations of multifunctional alkynes and aryl halides in structurally well‐defined mesoporous reactors. The growth of the polymeric nanoparticles was controlled by the spatial confinement of the nanoreactors, giving conjugated polymeric nanoparticles with narrow size distribution centered at 5 nm. All the obtained polymers are freely soluble in common solvents and can be fabricated into thin film. Both of the solution and thin film prepared from these polymeric nanoparticles were highly fluorescent, endowing them potential applications in light emitting and other optoelectronic fields. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2285–2290     

Solution polymerization of polybenzimidazole

Polybenzimidazoles (PBI) are an important class of heterocyclic polymers that exhibit high thermal and oxidative stabilities. The two dominant polymerization methods used for the synthesis of PBI are the melt/solid polymerization route and solution polymerization using polyphosphoric acid as the solvent. Both methods have been widely used to produce high‐molecular weight PBI, but also highlight the obvious absence of a practical organic solution‐based method of polymerization. This current work explores the synthesis of high‐molecular weight meta‐PBI in N,N‐dimethyl acetamide (DMAc). Initially, model compound studies examined the reactivity of small molecules with various chemical functionalities that could be used to produce 2‐phenyl‐benzimidazole in high yield with minimal side reactions. ¹H NMR and FTIR studies indicated that benzimidazoles could be efficiently synthesized in DMAc by reaction of an o‐diamine and the bisulfite adduct of an aromatic aldehyde. Polymerizations were conducted at various polymer concentrations (2‐26 wt % polymer) using difunctional monomers to optimize reaction conditions in DMAc which resulted in the preparation of high‐molecular weight m‐PBI (inherent viscosities up to 1.3 dL g^?1). TGA and DSC confirmed that m‐PBI produced via this route has comparable properties to that of commercial m‐PBI. This method is advantageous in that it not only allows for high‐polymer concentrations of m‐PBI to be synthesized directly and efficiently, but can be applied to the synthesis of many PBI derivatives. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 1795–1802     

Preparation and characterization of poly(2‐methacryloyloxyethyl phosphorylcholine)‐block‐poly(D,L‐lactide) polymer nanoparticles

A poly(D,L ‐lactide)–bromine macroinitiator was synthesized for use in the preparation of a novel biocompatible polymer. This amphiphilic diblock copolymer consisted of biodegradable poly(D,L ‐lactide) and 2‐methacryloyloxyethyl phosphorylcholine and was formed by atom transfer radical polymerization. Polymeric nanoparticles were prepared by a dialysis process in a select solvent. The shape and structure of the polymeric nanoparticles were determined by ¹H NMR, atomic force microscopy, and ζ‐potential measurements. The results of cytotoxicity tests showed the good cytocompatibility of the lipid‐like diblock copolymer poly(2‐methacryloyloxyethyl phosphorylcholine)‐block‐poly(D,L ‐lactide). © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 688–698, 2007     

Thermo‐ and pH‐induced self‐assembly of P(AA‐b‐NIPAAm‐b‐AA) triblock copolymers synthesized via RAFT polymerization

A series of environmentally sensitive ABA triblock copolymers with different block lengths were prepared by reversible addition‐fragmentation chain transfer (RAFT) polymerization from acrylic acid (AA) and N‐isopropylacrylamide (NIPAAm). The GPC and ¹H NMR analyses demonstrated the narrow molecular weight distribution and precise chemical structure of the prepared P(AA‐b‐NIPAAm‐b‐AA) triblock copolymers owing to the controlled/living characteristics of RAFT polymerization. The lower critical solution temperature (LCST) of the triblock copolymers could be tailored by adjusting the length of PAA block and controlled by the pH value. Under heating, the triblock copolymers underwent self‐assemble in dilute aqueous solution and formed nanoparticles revealed via TEM images. Physically crosslinked nanogels induced by inter‐/intra‐hydrogen bonding or core‐shell micelle particles thus could be obtained by changing environmental conditions. With a well‐defined structure and stimuli‐responsive properties, the P(AA‐b‐NIPAAm‐b‐AA) copolymer is expected to be employed as a nanocarrier for biomedical applications in controlled‐drug delivery and targeting therapy. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 1109–1118