制备条件对CdWO4纳米棒的光致发光性能的影响

以Na₂WO₄和CdCl₂为主要原料，在130 ℃水热制备了CdWO₄纳米棒，并用扫描电镜(SEM)、透射电镜(TEM)、粉末X射线衍射(XRD)和能谱元素分析(EDS)对产物进行了表征。结果表明，产物为长约100 nm，直径10～30 nm的CdWO₄纳米棒。研究了不同反应条件下制备的CdWO₄纳米棒的光致发光性能。     

系列纳米结构锰氧化物的水热合成

以KMnO₄为锰源、抗坏血酸(AA)为还原剂,采用水热法制备系列纳米结构锰氧化物。通过调节反应物的物质的量的比、水溶液的pH值、反应温度和反应时间,制备出了不同纳米结构的锰氧化物,包括Mn₃O₄纳米粒子、MnOOH、α-MnO₂和β-MnO₂纳米棒。采用XRD和TEM测试技术对合成产物进行了表征,同时对其反应机理进行了探讨。     

硼酸镍纳米棒溶胶-凝胶法合成及表征

以硝酸镍、硼酸和柠檬酸为原料,采用溶胶凝胶法于150 ℃形成咖啡色干凝胶,再于750 ℃焙烧得到硼酸镍纳米棒。采用XRD、SEM、TEM和FTIR对产物结构和形貌进行表征。结果表明产物为分布均匀的Ni₃(BO₃)₂纳米棒,纳米棒的长度受硝酸镍和硼酸的物质的量之比影响,硼酸用量越大,长度越大。当n_Ni3(BO3)2∶n_N3BO3=1∶3时,纳米棒直径为200~300 nm,长度为2~3 μm。对硼酸镍纳米棒的生长机理进行了探讨, 结果表明, 柠檬酸与镍离子反应产生网状结构的配合物,促使镍源均匀地分散在网格间,为硼酸镍纳米棒的生成提供有利的反应空间。     

氧化镓纳米带的合成和发光性质研究

采用化学气相沉积法，以碳纳米管作还原剂还原Ga₂O₃粉末，生成的气态Ga₂O和载气Ar中的微量O₂反应，在多孔氧化铝模板上沉积得到了Ga₂O₃纳米带。用扫描电子显微镜，透射电子显微镜和选区电子衍射对产物的结构和形态进行表征，发现产物为β-Ga₂O₃纳米带，宽度在20～500 nm之间，厚度为5～100 nm，长度可达几十微米。产物中还有几微米宽的Ga₂O₃纳米片。光致发光谱结果表明β-Ga₂O₃纳米带能发射蓝光和紫外光。文中还简单推测了β-Ga₂O₃纳米带的形成机理。     

载有C60的TiO2纳米粒子光催化活性

以水溶性C₆₀和TiO₂粒子为前驱体,采用水热法制备了载有C₆₀的锐钛矿型TiO₂纳米粒子。应用X射线衍射、透射电子显微镜、红外光谱、紫外-可见漫反射光谱、荧光光谱对产物进行了表征。以对-硝基苯酚为模型污染物研究了产物的光催化活性,结果表明适量负载C₆₀可以提高TiO₂纳米粒子的光催化活性,C₆₀起着传输电子、促进TiO₂光生载流子分离的作用,且经7次循环使用后对-硝基苯酚的降解效率仍能达到74%。讨论了载有C₆₀的TiO₂纳米粒子光催化降解对-硝基苯酚的机理。     

氧化铟八面体、纳米带、锯齿状纳米线和纳米链的可控合成

在N₂/H₂O混合气流中将硅片上金覆盖的金属铟颗粒加热到800 ℃制备出了不同形貌的In₂O₃纳米结构, 在距铟源不同距离处依次得到In₂O₃的八面体、纳米带、锯齿状纳米线和纳米链. 采用拉曼光谱、扫描电镜、X射线衍射和透射电镜对产物进行了表征分析. 结果表明, 八面体、纳米带、锯齿状纳米线和纳米链均为立方相单晶结构的In₂O₃. 基于气-固和气-液-固生长机理详细分析了八面体、纳米带、锯齿状纳米线和纳米链的生长过程, 提出了不同形貌In₂O₃纳米结构的生长模式.     

反相微乳液法制备纳米Al2O3颗粒及其形成反应机理的研究

通过聚乙二醇辛基苯基醚(曲拉通X-100)/正丁醇/环己烷/水溶液形成的体系, 采用反相微乳液法合成了Al₂O₃纳米粒子. 对前驱体进行热分析(TG-DTG-DTA), 确定了合适的煅烧温度为1150 ℃. 采用X射线衍射(XRD)、透射电镜(TEM)、紫外可见分光光度法(UV-vis)分别对产物的结构、粒度和形貌进行了表征, 考察了微乳液中水与表面活性剂的物质的量之比(ω_o)、煅烧温度和煅烧时升温速率等关键因素对产物形貌和晶相的影响, 并通过分析进一步揭示了Al₂O₃纳米粒子的形成机理. 结果表明, 控制ω_o为10、煅烧温度为1150 ℃可得到分散性好、粒径分布均匀的Al₂O₃纳米粒子, 且2 ℃/min的升温速率更有利于产物向稳定的α晶相转变.     

反相微乳液法制备纳米Al2O3颗粒及其形成反应机理的研究

通过聚乙二醇辛基苯基醚(曲拉通X-100)/正丁醇/环己烷/水溶液形成的体系, 采用反相微乳液法合成了Al₂O₃纳米粒子. 对前驱体进行热分析(TG-DTG-DTA), 确定了合适的煅烧温度为1150 ℃. 采用X射线衍射(XRD)、透射电镜(TEM)、紫外可见分光光度法(UV-vis)分别对产物的结构、粒度和形貌进行了表征, 考察了微乳液中水与表面活性剂的物质的量之比(ω_o)、煅烧温度和煅烧时升温速率等关键因素对产物形貌和晶相的影响, 并通过分析进一步揭示了Al₂O₃纳米粒子的形成机理. 结果表明, 控制ω_o为10、煅烧温度为1150 ℃可得到分散性好、粒径分布均匀的Al₂O₃纳米粒子, 且2 ℃/min的升温速率更有利于产物向稳定的α晶相转变.     

静电纺丝技术制备Y2O3∶Eu3+纳米带及其发光性质

采用静电纺丝技术制备了PVP/[Y(NO₃)₃+Eu(NO₃)₃]复合纳米带,将其进行热处理,获得了Y₂O₃∶Eu³⁺纳米带。采用XRD、FTIR、SEM、TEM、荧光光谱等技术对焙烧后的样品进行了表征。结果表明：600 ℃焙烧即可获得Y₂O₃∶Eu³⁺纳米带,800 ℃时结晶更为良好,产物属于立方晶系。纳米带表面光滑,由平均直径为30 nm的小颗粒紧密排列而成,为多晶结构。随着温度升高,纳米带宽度减小。焙烧800 ℃获得的Y₂O₃∶Eu³⁺纳米带的发光性质优于焙烧600 ℃的Y₂O₃∶Eu³⁺纳米带。与体材料相比,该纳米带的激发光谱Eu³⁺-O^2-电荷迁移态(CTB)发生红移,发射光谱发生蓝移。     

不同形貌纳米CoWO4的水热法制备及气敏性能

以Co（NO₃）₂·6H₂O、Na₂WO₄·2H₂O为主要原料,去离子水为溶剂,利用水热法在不同条件下制备了一系列的纳米CoWO₄,用XRD、TEM和比表面分析仪对产品的物相、形貌和比表面积进行了表征。较系统地探讨了水热条件（反应混合物pH值、反应时间、反应温度等）对产物物相和形貌的影响,并研究了不同形貌产品对甲醛、乙醇、氨气、苯和丙酮等的敏感性能。结果表明：水热条件对产品的物相和形貌有影响,在不同水热条件下,可成功制备CoWO₄纳米颗粒、纳米立方体及纳米棒;以纳米颗粒、纳米立方体及纳米棒样品制成的气敏元件对被试气体有不同程度的响应,其中以纳米颗粒为基的元件在210℃对1000μL·L^-1NH₃灵敏度为3.3。     

Preparation and characterization of a novel DABCO-based ionic liquid supported on Fe3O4@TiO2 nanoparticles and investigation of its catalytic activity in the synthesis of quinazolinones

In this study, quinazolinone derivatives have been synthesized via a suitable and efficient procedure by one-potmulti-component reactions of 3-amino-1,2,4-triazole or 2-aminobenzimidazole, dimedone and aromatic aldehydes in the presence of Fe₃O₄@TiO₂-IL as nanocatalyst under solvent-free condition. The products were prepared in good to excellent yields using Fe₃O₄@TiO₂-IL magnetic nanocatalyst. The Fe₃O₄@TiO₂ magnetic nanoparticles (MNPs) were prepared using beet juice extract and functionalized with IL based on DABCO. Moreover, the core-shell structured magnetic Fe₃O₄@TiO₂-IL has been characterized by different techniques such as ¹H-NMR, FT-IR, VSM, XRD, SEM, TGA, TEM and EDX. To the best of our knowledge, the prepared ionic liquid displayed a good protective and activator agent for magnetic nanocatalyst.     

CoFe2O4@SiO2-NH2-CoII NPs catalyzed Hantzsch reaction as an efficient,reusable catalyst for the facile,green, one-pot synthesis of novel functionalized 1,4-dihydropyridine derivatives

A magnetically heterogeneous CoFe₂O₄@SiO₂-NH₂-Co^II nanoparticle was synthesized by the immobilization of Co (II) complex onto CoFe₂O₄@SiO₂ nanoparticles, and the heterogeneous magnetic nanocatalyst was characterized by XRD, TEM, TGA, EDX, and FT-IR techniques. Then, the green and reusable method was introduced for a multicomponent synthesis of 1,4-dihydropyridine derivatives via Hantszch reaction. The synthesis of 1,4-dihydropyridine derivatives was proceeded by the reaction of aldehyde, ethyl acetoacetate, and ammonium acetate in the presence of this magnetic nanocatalyst in EtOH/Water (1:1). Simple work-up, short reaction times, excellent yields (60–96%) as well as green solvent are some advantages of this novel approach, and the corresponding products were purified with no need for chromatographic separation.     

Synthesis of SrFe12O19 magnetic nanoparticles by EDTA complex method

A modified polyacrylamide gel route was used to prepare SrFe₁₂O₁₉ magnetic nanoparticles; ethylenediaminetetraacetic acid (EDTA) was used as a carboxyl chelating agent. The phase purity, morphology and magnetic properties of as-prepared samples were analyzed via X-ray diffraction (XRD), Raman spectroscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM) and vibrating sample magnetometery (VSM). XRD analysis indicates that high-purity SrFe₁₂O₁₉ magnetic nanoparticles can be synthesized at 700°C in air. The characteristic peaks of as-prepared sample at 210, 283, 321, 340, 381, 411, 432, 475, 532, 618, 686, and 726 cm^–1 were observed in Raman spectra. SEM and TEM show that the synthesized SrFe₁₂O₁₉ magnetic nanoparticles are uniform with the mean particle size of ~60 nm. VSM measurement shows that the maximum magnetic energy product (BH)_max of sample prepared using EDTA as a chelating agent is higher than that of sample prepared using citric acid as a chelating agent.

     

Hydrothermal synthesis of monodisperse Fe3O4 nanoparticles based on modulation of tartaric acid

In this paper, monodisperse Fe₃O₄ nanoparticles with single crystalline structure were synthesized via a facile environment-friendly method. And the size of the nanoparticles ranges from 10 nm to 15 nm. As-synthesized Fe₃O₄ were characterized by X-ray diffraction instrument (XRD), X-ray photoelectron spectroscopy (XPS), Fourier transform infrared (FT-IR) spectrometer and field emission transmission electron microscope (FE-TEM). The effect of tartaric acid (TA) amount on products was investigated by XRD and TEM. The results indicated that TA could commendably modulate the crystalline phase, morphology and size of nanometer Fe₃O_4. A possible generated mechanism of Fe₃O₄ crystals was proposed in virtue of UV–vis absorption spectra. Besides, the magnetic properties of as-synthesized Fe₃O₄ were detected.     

Microwave-Assisted Elemental-Direct-Reaction Route to Nanocrystalline Copper Sulfides Cu9S8 and Cu7S4

Non-stoichiometric copper sulfides Cu₉S₈ and Cu₇S₄ nanocrystallites were synthesized by the reaction between elements S and Cu under microwave radiation for several minutes. The products were analyzed by using XRD, TEM, XPS, ICP and PL.     

Synthesis,characterization and electrochemical behavior of LiNi1−xBaxO2 (x = 0.0, 0.1, 0.2, 0.3 and 0.5) cathode materials

LiNiO₂ and Ba-doped LiNiO₂ were synthesized by a simple solid state reaction, and used as cathode active materials for lithium rechargeable batteries. Physical properties of the synthesized products are discussed in the light of structural (TG/DTA, XRD, TEM, SEM with EDAX) and spectroscopic (FTIR) measurements. XRD results show that the compounds are similar to LiNiO₂ in structure. TEM and SEM analyses were used to examine the particle size, nature and morphological aspects of the synthesized oxides. The composition of the materials was explored by EDAX analysis. Performances of lithiated oxides as cathode materials in lithium-ion batteries and substitutive effect on electrochemical properties have been investigated by cyclic voltammetry and galvanostatic charge–discharge cycling. By substitution of Ni with Ba, in LiNi_0.8Ba_0.2O₂ has yielded better cycling results compared to all other materials revealed through charge–discharge studies.     

Superparamagnetic Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> Nanoparticles Decorated Multiwalled Carbon Nanotubes: Preparation via Cyclic Microwave Approach and Their Drug Release Behavior

Superparamagnetic Fe₃O₄ nanoparticles decorated multiwalled carbon nanotubes were synthesized by cyclic microwave method and the effect of different reaction parameters on the products were also investigated. The as synthesized products were characterized by XRD, TEM, SEM, EDS, FT-IR, VSM, and Uv–Vis spectroscopy. It was observed that precursors’ concentration ratio had great effect on the particle size and decorating quality. Also the effect of the other parameters including irradiation power and time on product size and uniformity of the product were also investigated. The best products with desired particle size distribution obtained when irradiation power and reaction time were 900 W and 6 min, respectively. Aspirin and acetaminophen were applied as a model drug and the drug release behavior of the composite was investigated. It was observed that the drug discharge was highly dependent to the pH and can be tuned by applying magnetic field.     

室温下合成纺锤形貌六方相NaLnF_4(Ln=Nd,Sm,Eu,Gd,Tb)纳米颗粒

室温下合成长250nm,宽100nm的纺锤形貌六方相的NaNdF4。NaEuF4,NaSmF4,NaGdF4和NaTbF4也用同样的方法获得。产物用XRD,TEM,HRTEM,FESEM和PL进行表征。PL光谱显示合成的NaEuF4的激发波长是394nm。NaEuF4有4个特征发射谱带,分别是591,615,650和681nm。     

Synthesis of bioactive magnetic nanoparticles spiro[indoline-3,4′-[1,3]dithiine]@Ni (NO3)2 supported on Fe3O4@SiO2@CPS as reusable nanocatalyst for the synthesis of functionalized 3,4-dihydro-2H-pyran

New bioactive magnetic nanoparticles of spiro[indoline-3,4′-[1,3]dithiine]@Ni (NO₃)₂ supported on Fe₃O₄@SiO₂@CPS were synthesized in five steps. The structure of synthesized magnetic nanoparticles was identified by using Energy-Dispersive X-ray spectroscopy (EDX), Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM), X-Ray Diffraction (XRD), Thermal Gravimetric Analysis (TGA), Infrared spectroscopy (FT-IR), Inductively Coupled Plasma-Optical Emission Spectroscopy (ICP-OES), Vibrating Sample Magnetometer (VSM) and Brunauer Emmett Teller (BET) surface analysis. Antimicrobial activity of the synthesized magnetic nanoparticles based on MIC (Minimum Inhibitory Concentration) and MBC (Minimum Bactericidal Concentration) and MFC (Minimum Fungicidal Concentration) values were also examined. Furthermore, the synthesized magnetic nanoparticles exhibited appropriate catalytic properties in the synthesis of the 3,4-dihydro-2H- pyran derivatives.     

反应溶剂对Bi2S3粉体形貌的影响

利用溶剂热法在不同反应溶剂中制备了不同尺寸的Bi2S3纳米管和纳米棒.利用XRD、SEM、TEM、选区电子衍射(SAED)和高分辨透射电镜(HRTEM)对其结构和形貌进行了表征.结果表明,所制备的产物是结晶良好的正交相Bi2S3,反应溶剂的表面张力、粘度大小和反应溶剂中的比例影响纳米粉体的形貌和尺寸.紫外-可见光吸收光谱测量表明,由于尺寸效应所有粉体的吸收谱相对于正交相的Bi2S3块体都出现蓝移.