A Study on Kinetics of the Bronze Powder-Corrosion Development

HCl acid was applied to the surface of the self-prepared Cu-Sn-Pb alloy, and the methods of IR-REF, IR-PAS, XRD, SPM, SEM, TEM and pH were employed to study the forming process and the developing speed of the bronze powder-corrosion Cu_2(OH)_3Cl (PC). It is found that the corrosion develops fast in acid environment at room temperature; the corrosion Cu_2(OH)_3Cl with valence Cu~(2+) forms from alloy through the intermediate corrosion CuCl with valence Cu~+; PC is contagious, which can pollute the fresh bronze alloy from the corroded sample by air; when CuCl is oxidized to produce Cu_2(OH)_3Cl, Cu~(2+) cation forms at the same time, and both the oxidizing reactions have zero-order reaction with respect to O_2 in the air; the P1 formation reaction has first-order reaction with respect to Cull; in enormous distilled water Cu_2(OH)_3Cl forms from CuCl through the intermediate product Cu_2O.All the results above are discussed in the present article, and the mechanism of PC formation is studied further. The r     

氯化亚铜氧化反应的化学动力学初探

多数被发掘的古代青铜文物表面都附着有某些钢锈,其中以粉状锈(Cu_2(OH)_3Cl)对铜器的腐蚀最为严重.迄今已有一些文献介绍粉状锈的生成机理,但对其反应过程的动力学研究尚未见报导。作为青铜合金中含量最丰的元素铜,被氧化腐蚀是分步进行的.本工作主要用X-光衍射及分光光度法对一价铜锈CuCl在潮湿环境中进行氧化反应的速度常数及表观活化能进行测定核算;对反应的中间产物及伴随现象进行分析探讨。     

青铜器文物腐蚀受损原因的研究

以三千多年前商周时代为代表的青铜器是我国金属质地文物中的珍品。本文调查了青铜病的发现‘症状’,对青铜病形成的过程和原因,以小孔腐蚀原理研究了溶液的ＰＨ值和Ｃｌ＾－浓度对青铜腐蚀的影响,进行了模拟闭塞电池内化学和电 化学状态的研究,提出出青铜病的产生机理并探讨符合文物保护要求的青铜器保护处理方法。     

Preparation of YSZ Coated AISI-Type 316L Stainless Steel by the Sol-Gel Coating Method and Its Corrosion Behavior in Molten Carbonate

The effect of heat-treatment conditions on the corrosion behavior of yttria stabilized zirconia (YSZ) coated AISI-type 316L stainless steels in molten carbonate are investigated. YSZ films on stainless steel were prepared by the sol-gel method. While the sample heat-treated at 800°C for 2 hours in air has an uneven surface microstructure with macrocracks, a YSZ coated sample heat-treated in argon has an even microstructure. The polarization resistance and corrosion rate of YSZ coated sample heat-treated in air were deteriorated from 6.948 cm² and 364.7 mpy (millimeter per year) to 3.291 cm² and 769.8 mpy, respectively, by the corrosion for 100 hours due to its poor surface microstructures. At the same experimental condition, meanwhile, those corrosion parameters of YSZ coated sample heat-treated in argon were 15.43 cm² and 164.2 mpy, respectively, and those were improved to 18.83 cm² and 134.6 mpy after the corrosion for 100 hours. This is attributed to the YSZ film with well developed surface microstructures. The concentration profiles of elements and X-ray diffractograms indicate that the oxide layer of YSZ coated sample heat-treated in argon had a triple layer structure composed of outer YSZ film, in between Fe₂O₃ layer, and inner chromium rich layer during corrosion.     

Cu-Ni合金在NaCl溶液中的孔蚀特性

采用慢速电位扫描法和电位台阶计时电流法分别研究铸态铜镍合金以及由机械合金化方法制备的纳米晶铜镍合金于不同浓度NaCl溶液中的孔蚀特性.讨论含Ni量,Cl-浓度等因素对合金孔蚀敏感性的影响,探讨了不同结构合金的孔蚀发展.     

Effect of Sintering Temperature on the Corrosion and Wear Behavior of Protective SiO2-Based Sol-Gel Coatings

Sol-gel hybrid organic-inorganic and inorganic SiO₂-based protective coatings with and without added 3 m glass particles were developed and tested for their corrosion and wear behavior of an stainless steel substrate (AISI316L). The corrosion resistance greatly increases by incorporating glass particles in the sols. The incorporation of particles in the coatings allows the synthesis of thicker crack-free coatings. On the other hand, the corrosion resistance increases for coatings with a higher organic content obtained at lower sintering temperature. These coatings are also highly stable in saline aqueous solutions. However, the wear resistance is badly affected by the hybrid character of the SiO₂ matrix. The optimum coating process in terms of corrosion and wear resistance, appears to be a hybrid system with a dense SiO₂ network achieved at intermediate sintering temperatures.     

Bi(Pb)-Sr-Ca-Cu-O体系中110K超导相的制备和结构研究

The stable superconducting phase with T_c 110 K has been prepared in samples of nominal composition (Bi_(2-x)Pb_x)Sr_2Ca_2Cu_3O_y and (Bi_(2-x)Pb_x)Sr_2Ca_3Cu_5O_y x=0.2, 0.4, 0.6. The crystal strucuure of the superconducting phase (Bi_1.8Pb_0.2)Sr_2Ca_2Cu_3O_y with T_c 106.3 K has been determined in the sample of nominal composition (Bi_1.8Pb_0.2)Sr_2Ca_3Cu_5O_y. It is a nine decker perovskite arrangement by incorporating two extra layers CaCuO_2 in each cell of Bi_2Ca_1Cu_2O_y. The plane of CuO_2 is planar in incorporating layer CaCuO_2. Speace group D~1_(2h)-Pmmm was assigned. Adding Pb is in Bi site, and atomic radius and atomic valence in Bi site was modified, so that it is able to stabilize crystal structure and progress superconducting properties.     

Study on corrosion resistance of electroplating zinc–nickel alloy coatings

Electrodeposited zinc–nickel alloy coatings have been widely adopted for surface treatment of automobile body steel sheet for high corrosion resistance. The corrosion behavior of the coatings has been related with the components of nickel, and the zinc–nickel alloy passive coatings have much higher corrosion resistance than that of zinc–nickel alloy coatings. In the present paper, the corrosion resistance behavior of the zinc–nickel alloy coatings obtained by new process and formulation has been studied by means of the electrochemistry test and neutral salt spray test. And it is discovered that the properties of corrosion resistance of zinc–nickel alloy passive coatings were better than that of zinc passive coatings, Cadmium passive coatings and alloys of electrodeposited cadmium–titanium. The components of corrosion productions, in terms of X‐ray diffraction (XRD), are mainly ZnO, ZnCl₂ · 4Zn(OH)₂ and small quantity of 2ZnCO₃· 3Zn(OH)₂. The component of zinc–nickel alloy coatings has been investigated with Glow Discharge Optical Emission Spectrometry (GDA‐750). And it is found that as the thickness of zinc–nickel alloy coatings increases, the component of zinc increases from beginning to end, but the peak value of nickel appears and an enrichment of nickel in the coatings comes into being. Because the electrodeposited zinc–nickel alloy coatings exhibit different alloy phases as a function of their alloy composition, in this paper, the crystal structure changing with the different component of nickel has been studied in terms of XRD. The result shows that electrodeposited zinc–nickel alloy has different phases: α‐phase, a solid solution of zinc in nickel with an equilibrium solubility of about more than 79% nickel; γ‐phase, an intermediate phase with a composition Ni₅Zn₂₁; η‐phase, a solid solution of nickel in zinc with less than 5% nickel; and δ‐phase (Ni₃Zn₂₂) appeared from η‐phase to α‐phase with increasing content of nickel. Copyright © 2009 John Wiley & Sons, Ltd.     

Atomic Force Microscopy Study of NaOH Corroded Al2O3-TiO2-SiO2 Coatings on Glass

Atomic force microscopy (AFM) was used to study the performance of 80 nm thick Al2O3-TiO2-SiO2 sol-gel coatings on glass substrates following corrosion in 1 M NaOH solutions at 60°C. The as-prepared coatings were homogeneous on a nanoscale and displayed the glass pattern before corrosion. Layers with different compositions behaved differently during the corrosion process. Thus, TiO2 or TiO2-dominated layers had tetragonal-like crystals on their surfaces after corrosion, possibly of anatase composition. On the other hand, layers with a molar ratio Al2O3 : SiO2 near 1 : 2 displayed a pseudo-hexagonal morphology, possibly with a nepheline (Na2O · Al2O3 · 2SiO2) composition. Layers of 5Al2O3-40TiO2-55SiO 2 were corroded is a stepwise fashion and had no special surface morphology.     

Double laminated reduced graphene/Cu_2S/reduced graphene/graphene oxide nanofilms and their photoelectrochemical properties

In this work,an efficient photocatalytic material was prepared directly on Indium tin oxide(ITO)glass substrates by fabricating Cu_2 S and graphene oxide onto graphene for photoelectrochemical(PEC) water splitting.The double laminated reduced graphene/Cu_2S/reduced graphene/graphene oxide(RG/Cu_2S/RG/GO) nanofilms were characterized,and an enhanced photoelectrochemical response in the visible region was discovered.The photocurrent density of the nanofilms for PEC water splitting was measured to be up to 1.98 m A/cm~2,which could be ascribed to the followings:(i) a higher efficiency of light-harvesting because of GO coupling with Cu_2 S that could broaden the absorbing solar spectrum and enhance the light utilization efficiency;(ii) a stepwise structure of band-edge levels in the Cu_2S/GO electrode was constructed;(iii) double laminated electron accelerator(RG) was used in the Cu_2S/GO materials to get better electron-injecting efficiency.     

Study by grazing incident diffraction and surface spectroscopy of amalgams from ancient mirrors

Characterization of four amalgam surfaces, with different alteration degrees from Andalusia historical mirrors, has been carried out by grazing-incidence X-ray diffraction (GIXRD), and other spectroscopic techniques (SEM/EDX, XPS, and REELS). The combination of all these techniques allows determining the corrosion state of the amalgams. The results show that the amalgams are composed in all cases of a binary alloy of tin and mercury. As mercury has high vapour pressure at RT, it slowly segregates and eventually evaporates, it leaves finely divided particles of tin that easily can be oxidize, forming tin monoxide (SnO) and tin dioxide (SnO₂). In one of the samples, most of the amalgam remains unoxidized, since Hg_0.1Sn_0.9 and metallic Sn phases are the major components; in two other samples, Hg_0.1Sn_0.9 and Sn phases are not detected while SnO₂ and SnO phases appear. Finally, in the last studied sample, only SnO₂ phase is detected. The surface analyses of these samples by XPS show that, for most of them an unique chemical species (Sn⁴⁺) is found.      

EIS characterization of corrosion processes of titanium and alloy UNS N10276 in sour environments

Titanium grade 2 (UNS R50400) and nickel-based alloy (UNS N10276) were electrochemically investigated to explore their corrosion susceptibility in sour (H₂S) environments typically found on atmospheric distillation units in crude oil refineries. Electrochemical impedance spectroscopy (EIS) was used to attain the experimental results. Two individual solutions (0.05 mol/l HCl and 0.05 mol/l HCl + 500 ppm H₂S) were utilized in the laboratory work to replicate major corrosive agents present in actual atmospheric distillation systems for a characteristic heavy crude oil produced in Mexico. Metals were examined at pH 1.5, 4, 6, 8, and 10 values for the two solutions to identify the effects of pH modification on corrosion processes. The results disclosed that each metal has dissimilar corrosion susceptibility depending on the pH of the environment. Therefore, pH intervals for which every metal holds minimum susceptibility were identified. In addition, the convenience of controlling the pH of streams within a definite interval (5.5–6.5) is discussed and a few hints on decision-making to improve the operation of atmospheric distillation units are also explained.

Investigation of Glass-Like Sol-Gel Coatings for Corrosion Protection of Stainless Steel Against Liquid and Gaseous Attack

Glass-like sol-gel coatings have been investigated as corrosion protective coatings on stainless steel. Magnesium- and borosilicate coatings with thickness of about 100–700 nm and methyl-modified SiO2 coatings with a thickness of about 2 m were deposited on stainless steel plates by dip-coating. The coatings were densified between 400°C and 500°C in different atmospheres (N2, air) for 1 h. The corrosion protection against gaseous attack was investigated by accelerated corrosion tests, at 800°C in air for 1 h. A corrosion protection factor was calculated from the relation Fe/Fe2O3, determined by XRD on the surface of coated and uncoated samples. Methyl-modified SiO2 coatings showed a protection factor, which was 2 orders of magnitude higher than for the other coatings. Electrochemical investigations were performed on samples submerged in a NaCl solution for 200 h. The corrosion propagation, polarization resistance and impedance vector were measured. For accelerated corrosion tests, polarization intensity curves were determined for high potentials of up to 1 V. Again excellent results were obtained for the methyl-modified SiO2 coatings, which remained passive for 200 h. Results of the salt spray corrosion test, however, showed no corrosion protection by the sol-gel coatings. After 2000 h in the salt spray chamber the steel was corroded and the coatings peeled off. It is concluded that for the further development of these coatings an improved interfacial passivation will be required.     

AM60镁合金在汽车发动机冷却液中的腐蚀电化学行为

研究AM60镁合金在3种(A、B、C)市售汽车发动机冷却液中的腐蚀电化学行为.极化曲线、电化学阻抗谱测试表明,冷却液A对AM60镁合金的腐蚀性最强,B腐蚀性略低于A,C腐蚀性最弱,最适于镁合金汽车发动机使用.冷却液对发动机镁合金材料的腐蚀性与其电阻有关系,电阻越大,腐蚀性越小;冷却液中的乙二醇和添加剂组分在镁合金表面的竞争吸附对镁合金的腐蚀行为也有重要影响.     

Synthesis and magnetic properties of copper(II)-lanthanoid(III)-copper(II) trinuclear complexes with N,N′-bis(2-aminoethyl)-oxamido ligand

Summary Ten novel -oxamido trinuclear complexes, namely Cu₂–(oxae)₂Ln(ClO₄)₃ (Ln = Y, Pr, Sm, Eu, Gd, Tb, Dy, Ho, Er and Yb), where oxae donotes the N,N-bis(2-aminoethyl)-oxamido dianion, were prepared and characterized. The magnetic susceptibility of Cu₂(oxae)₂Gd(ClO₄)₃ was measured over the 4–300 K range and the observed data were successfully simulated by an equation based on the spin Hamiltonian operator . The exchange integrals J _(Gd-Cu) and J _Gd-Cu were found to be 2.37 and –0.71cm^-1, respectively, indicating that very weakly ferromagnetic spin-exchange interaction operates between copper(II) and gadolinium(III) ions.Visiting scholar: Qufu Normal University.     

碱式碳酸铜微球的表面改性和组装

报道了通过分散聚合反应在碱式碳酸铜微球表面锚接聚苯乙烯纳米粒子, 以调节其亲水/亲油性的方法. 结果表明, 锚接的聚苯乙烯纳米粒子尺寸愈大, 所得的改性碱式碳酸铜微球疏水性愈强. 用对油和水润湿性适中的改性碱式碳酸铜微球为乳化剂, 能够制备出稳定的油包水型Pickering乳液. 改性碱式碳酸铜微球组装在Pickering乳液的分散相液滴表面, 形成一个固体壳层. 将Pickering 乳液的分散相水核凝胶化, 合成出分级结构琼脂糖凝胶微球.     

Cu2O立方体的快速制备及模板法制备CuxS纳米笼子

首先以NaBH₄作为强还原剂在CuSO₄溶液中快速形成Cu₂O晶核, 然后以葡萄糖为温和的还原剂和保护剂, 由晶核生长成Cu₂O立方体, 并以其为模板制备中空的球状Cu_xS纳米笼子. 利用透射电子显微镜(TEM), 扫描电子显微镜(SEM), X射线衍射仪(XRD)和紫外-可见(UV-Vis)分光光度计对产物进行表征. 葡萄糖和铜盐的物质的量的比、加热状况、pH等反应条件影响Cu₂O的形貌. Cu_xS纳米笼子的外壳厚度由参与反应的Cu₂O和Na₂S的物质的量的比决定.     

Corrosion inhibition of zinc-plated steel in 0.5, 1 and 1.5 M sulphuric acid by poly(ethylene glycol)

The effect of poly(ethylene glycol) (PEG) 4000 on the corrosion of zinc-plated steel in H₂SO₄ has been investigated over a wide range of conditions. It was found that the corrosion rate depends upon exposure time. The rate of corrosion goes down rapidly to reach a low value, which is an almost constant value within 5 hr under most conditions. This trend was also found by Growock and Lopp for the inhibition of steel corrosion in HCl with 3-phenyl-2-propyl-1-ol. Other workers have linked this slow fall-off in the corrosion rate to film formation. The corrosion rate was found to decrease slowly with increasing PEG concentration, and to increase slowly with acid concentration for all conditions. The effect of temperature on corrosion rate was found to be similar to that of acid concentration. The corrosion rate decreased exponentially with poly(ethylene glycol) concentration. The percentage inhibition reached a value of 48.93 for a PEG concentration of 4 ppm: to double this, the concentration had to be increased to 40,000 ppm. Sulphuric acid titration against sodium hydroxide showed no change in acid concentration during the corrosion protection process, thus supporting the film protection theory     

Electrochemical and Surface Analysis Studies on the Carbon Dioxide Corrosion of X‐65 Carbon Steel

A comprehensive study of the CO₂ corrosion of carbon steel (X‐65) at low partial pressures of CO₂ is reported in this paper. Field emission scanning electron microscopy (FESEM), Raman spectroscopy (RS), synchrotron radiation‐grazing incidence X‐ray diffraction (SR‐GIXRD), and electrode kinetic studies have confirmed that chukanovite, magnetite and siderite are the main corrosion products at low partial pressures of CO₂. Chukanovite forms predominantly in the presence of CO₂, while magnetite was found to be the major corrosion product in the absence of CO₂, although the majority of previous work based on conventional ex‐situ materials characterization techniques has implied that siderite is the main corrosion product. Here, it is shown that the nature of corrosion products is strongly dependent on the experimental conditions at low pressures of CO₂, which has not been elucidated in previous studies. Accordingly, this study has made a significant contribution to identifying the true nature of corrosion scales formed at low partial pressures of CO₂ allowing the development of effective anti‐corrosive agents for the control and prevention of carbon steel corrosion at low CO₂ partial pressures.     

腐蚀金属电极的电化学频域测量研究进展──金属腐蚀与防护研究所电化学研究介绍之一

腐蚀金属电极的电化学频域测量研究进展──金属腐蚀与防护研究所电化学研究介绍之一曹楚南（金属腐蚀与防护国家重点实验室,金属腐蚀与防护研究所,沈阳１１００１５）腐蚀电化学是研究与腐蚀有关的电化学问题,具体的研究对象为腐蚀金属电极。虽然电化学中的基本原理和...