Preconcentration of trace amounts of silver ion in aqueous samples on octadecyl silica membrane disks modified with hexathia-18-crown-6 and its determination by atomic absorption spectrometry

A simple and reliable method has been developed to selectively separate and concentrate trace amounts of silver ion from aqueous samples for the subsequent measurement by atomic absorption spectrometry. Ag⁺ ions are absorbed quantitatively during passage of aqueous samples through an octadecyl-bonded silica membrane disk modified by hexathia-18-crown-6. Almost all matrix elements will pass through the disk to drain. The retained Ag⁺ ions are then stripped from the disk with a minimal amount of thiosulfate solution as eluent. The proposed method permitted large enrichment factors of about 200 and higher. The limit of detection of the proposed method is 50 ng Ag⁺ per 1000 mL. The effects of various cationic interferences on the recovery of silver in binary mixtures were studied. The method was applied to the recovery of Ag⁺ ions from different synthetic and water samples. Received: 28 September 1999 / Revised: 2 December 1999 / Accepted: 8 December 1999     

Solid-phase extraction and determination of ultra trace amounts of lead,mercury and cadmium in water samples using octadecyl silica membrane disks modified with 5,5′-dithiobis(2-nitrobenzoic acid) and atomic absorption spectrometry

A simple and fast method for preconcentration and determination of ultra trace amounts of lead(II), mercury(II) and cadmium(II) in water samples is presented. Lead, mercury and cadmium adsorbed quantitatively during passage of water samples (pH?=?7, flow rate?=?20 mL min^?1) through octadecyl silica membrane disks modified with 5,5′-dithiobis(2-nitrobenzoic acid). The retained lead, mercury and cadmium are then stripped from the disk with a minimal amount of 1 M hydrochloric acid solution as eluent, and determined by atomic absorption spectrometry. The influence of flow rates of the eluent and sample solution, the amount of ligand, type and least amount of eluent, pH of sample, effect of other ions and breakthrough volume are determined. The breakthrough volume of the method is greater than 2000 mL for lead and greater than 1500 mL for mercury and cadmium, which results in an enrichment factor of 200 for lead and an enrichment factor of 150 for both mercury and cadmium. The limit of detection of the proposed method is 177, 2 and 13 ng l^?1 for lead, mercury and cadmium, respectively.     

Improvements on the method for determining of <Superscript>210</Superscript>Pb and <Superscript>210</Superscript>Po in lead

An improved method is proposed to determine the content of ²¹⁰Pb in lead using ²¹⁰Po measured by alpha-ray spectrometry. This improved method, which is based on radiochemical separation by DDTC–toluene extraction, employs EDTA and citrate as masking reagents for the lead ions. To selectively extract polonium from an alkaline solution, the pH dependency was examined using a liquid scintillation counting method. And pH 9 was chosen as an extraction condition. Then ²¹⁰Po was electrodeposited on a stainless steel disk, and the chemical recovery was followed by ²⁰⁹Po tracer. The effectiveness of the new method was validated by the agreement with the analytical results from five samples as determined by gamma-ray spectrometry.     

Preconcentration and Determination of Trace Amounts of Heavy Metals in Water Samples Using Membrane Disk and Flame Atomic Absorption Spectrometry

A fast and simple method for preconcentration of Ni^2＋, Cd^2＋, Pb^2＋, Zn^2＋, Cu^2＋ and Co^2＋ from natural water samples was developed. The metal ions were complexed with sodium diethyldithiocarbamate （Na-DDTC）, then adsorbed onto octadecyl silica membrane disk, recovered and determined by FAAS. Extraction efficiency, influence of sample volume and eluent flow rates, effects of pH, amount of Na-DDTC, nature and amount of eluent for elution of metal ions from membrane disk, break through volume and limit of detection have been evaluated. The effect of foreign ions on the percent recovery of heavy metal ions has also been studied. The limit of detection of the proposed method for Ni^2＋, Cd^2＋, Pb^2＋, Zn^2＋, Cu^2＋ and Co^2＋was found to be 2.03, 0.47, 3.13, 0.44, 1.24 and 2.05 ng·mL^-1, respectively. The proposed （DDTC） method has been successfully applied to the recovery and determination of heavy metal ions in different water samples.     

Flame atomic absorption spectrometric determination of μg amounts of Fe (III) ions after solid phase extraction using modified octadecyl silica membrane disks

A simple, rapid and reliable method has been developed to selectively separate and concentrate ultra trace amounts of Fe (III) ions from aqueous samples for the measurement by flame atomic absorption spectrometry (FAAS). By the passage of aqueous samples through an octadecyl silica membrane disk modified by a recently synthesized Schiff base (Bis-(4-nitro phenyl azo) salisilidine-1,3-diamino propane), Fe(III) ions adsorb quantitatively and most of matrix elements will pass through the disk to drain. The retained iron ions are then stripped from the disk by minimal amount of 0.1 mol l^− 1 sulfuric acid as eluent. Extraction efficiency and the influence of pH, flow rates, amount of ligand, type and least amount of stripping acid as eluent were evaluated. The recovery of the iron from aqueous solution on the membrane disk modified with 3 mg Schiff's base was quantitative over pH 2–4.5.     

Preparation of PbS Nanoparticles by Phase-Transfer Method and Application to Pb2+-Selective Electrode Based on PVC Membrane

Abstract

A novel approach to prepare homogeneous PbS nanoparticles by phase-transfer method was developed. The preparatory conditions were studied in detail, and the nanoparticles were characterized by transmission electron microscopy (TEM) and UV-vis spectroscopy. Then a novel lead ion-selective electrode of polyvinyl chloride (PVC) membrane based on these lead sulfide nanoparticles was prepared, and the optimum ratio of components in the membrane was determined. The results indicated that the sensor exhibited a wide concentration range of 1.0 × 10^?5 to 1.0 × 10^?2 mol·L^?1. The response time of the electrode was about 10 s, and the optimal pH in which the electrode could be used was from 3.0 to 7.0. Selectivity coefficients indicated that the electrode was selective to the primary ion over the interfering ion. The electrode can be used for at least 3 months without any divergence in potential. It was successfully applied to directly determine lead ions in solution and used as an indicator electrode in potentiometric titration of lead ions with EDTA.     

Solid phase extraction and determination of lead in soil and water samples using octadecyl silica membrane disks modified by bis[1-hydroxy-9,10-anthraquinone-2-methyl]sulfide and flame atomic absorption spectrometry

A simple, reliable and relatively fast method has been developed to selectively separate and concentrate trace amounts of lead from aqueous samples for the measurement by flame atomic absorption spectrometry. By the passage of aqueous samples through an octadecyl-bonded silica membrane disk modified by a recently synthesized bis(anthraquinone)sulfide, Pb(2+) ions adsorb quantitatively and almost all matrix elements will pass through the disk to drain. The retained lead ions are then stripped from the disk by minimal amount of acetic acid as eluent. The proposed method permitted large enrichment factors of about 300 and higher. The limit of detection of the proposed method is 50 ng Pb(2+) per 1000 ml. The effects of various cationic interferences on the recovery of lead in binary mixtures were studied. The method was successfully applied to the determination of lead in soil and water samples.     

Triazine-modified magnetite nanoparticles as a novel sorbent for preconcentration of lead and cadmium ions

We report on a new sorbent for preconcentration of cadmium and lead ions that is based on triazine-functionalized magnetite nanoparticles that were prepared by direct silylation of magnetic nanoparticles with 3-aminopropyltriethoxysilane-2,4-bis(3,5-dimethylpyrazol)-triazine. The sorbent was characterized by IR spectroscopy, X-ray powder diffraction, scanning electron microscopy, thermal and elemental analysis. The sorbent was applied to the preconcentration of lead and cadmium ions which then were quantified by FAAS. The effects of sample pH value, extraction time, of type, concentration and volume of eluent, and of elution time were optimized. The limits of detection are 0.7 ng mL⁻¹ for Pb(II) ion and 0.01 ng mL⁻¹ for Cd(II). The effects of potentially interfering ions often found in real samples on the recovery in the determination of cadmium and lead ions in real samples were also investigated. The accuracy of the method was confirmed by analyzing the certified reference materials NIST 1571 (orchard leaves) and NIST 1572 (citrus leaves). Finally, the method was successfully applied to the determination of cadmium and lead ions in some fruit samples.

We report on a new sorbent for preconcentration of cadmium and lead ions that is based on triazine-functionalized magnetite nanoparticles. After optimization of the preconcentration step the method was successfully applied to the determination of cadmium and lead ions in some fruit samples

     

“On–off–on” pyrene-based fluorescent chemosensor for the selective recognition of Cu2+ and S2− ions and its utilization in live cell imaging

A new “on–off–on” fluorescence chemosensor (DPD) was designed, synthesized, and characterized based on pyrene and benzothiozole hydrazide. The probe DPD shows high affinity towards Cu²⁺ ions and the DPD-Cu²⁺ ensemble shows high sensitivity towards S²⁻ ions through the displacement method in the presence of other interfering ions. The detection limits of DPD for Cu²⁺ and S²⁻ ions were found to be 0.73 and 0.87 nM, respectively. Furthermore, the receptor was effectively applied to recognize Cu²⁺ and S²⁻ ions in real samples and live A549 cells through imaging studies.     

Flame atomic absorption determination of palladium in solutions after preconcentration using octadecyl silica membrane disks modified by thioridazine.HCl

A new simple and reliable method for rapid and selective extraction and determination of trace level of Pd(II) ion is developed. Palladium ions are adsorbed quantitatively during passage of aqueous samples through octadecyl silica membrane disks modified with thioridazine·HCl (TRH). The influence of flow rates of eluent and sample solution, amount of ligand, types and least amount of eluent, and pH of samples were studied. Almost all matrix elements were found to pass through the disk to drain. Break through volume and limit of detection of the membrane disks modified by 5 mg of TRH was found to be 1.0 l and 12 μg l⁻¹, respectively. The retained Pd(II) ions are then stripped from the disk with a minimal amount of sulfite solution as eluent and subsequently measured by atomic absorption spectrometry. The proposed method permitted large enrichment factors of about 100 and higher. The method was applied to the recovery of Pd(II) ions from different industrial samples and waters.     

Electrochemical Behaviour of Poly(benzopyrene) Films Doped with Eriochrome Black T as a Pb2+‐Sensitive Sensors

Poly(benzopyrene) films were electrosynthesized on glassy carbon disk electrodes from benzo(a)pyrene by cyclic voltammetry in the presence of eriochrome black T, which forms strong complexes with lead ions. In consequence, by conditioning the films in high concentration of lead (0.1 mol dm^?3 Pb(NO₃)₂) potentiometric sensitivity to lead ions down to 10^?5 mol dm^?3 Pb²⁺ was induced, and a novel type of lead‐sensitive electrode was obtained. The electrode is characterized by high stability of the potential readouts, good reproducibility of the calibration curves as well as a minor hysteresis effects. The performance of our lead‐sensitive electrode was favourable compared to PEDOT and PPy‐based electrodes doped with eriochrome black T. We conclude that poly(benzopyrene) doped with eriochrome black T is a new electroactive material that may be applied in sensor technology.     

Solid Phase Extraction of Lead(II) by Sorption on Grinded Eucalyptus Stem and Determination with Flame Atomic Absorption Spectrometry

A sensitive and simple solid‐phase preconcentration procedure for the determination of trace amount of lead by flame atomic absorption spectrometry (FAAS) is developed. The method is based on the adsorption of Pb²⁺ on the column of fine grinded eucalyptus stem adsorbent, elution of the column by nitric acid and subsequent determination by FAAS. The effect of different variables such as pH, eluent type, flow rate and interfering ions on the recovery of the analyte was investigated and optimum conditions were established. The adsorption of lead onto fine grinded eucalyptus stem can formally be described by a Langmuir equation with a maximum adsorption capacity of 4.49 mg g^?1. A preconcentration factor of 50 was achieved using the optimum conditions. The calibration graph was linear in the range 10–125 ng mL^?1 of lead in the initial solution with r = 0.9982. The limit of detection based on 3S_b criterion was 4.5 ng mL^?1 and the relative standard deviation for eight replicate measurements of 30 and 80 ng mL^?1 of iron was 3.6 and 2.8%, respectively. The method was successfully applied to the determination of lead added to well, tap and wastewater samples.     

Triazine-modified magnetite nanoparticles as a novel sorbent for preconcentration of lead and cadmium ions

We report on a new sorbent for preconcentration of cadmium and lead ions that is based on triazine-functionalized magnetite nanoparticles that were prepared by direct silylation of magnetic nanoparticles with 3-aminopropyltriethoxysilane-2,4-bis(3,5-dimethylpyrazol)-triazine. The sorbent was characterized by IR spectroscopy, X-ray powder diffraction, scanning electron microscopy, thermal and elemental analysis. The sorbent was applied to the preconcentration of lead and cadmium ions which then were quantified by FAAS. The effects of sample pH value, extraction time, of type, concentration and volume of eluent, and of elution time were optimized. The limits of detection are 0.7 ng mL^?1 for Pb(II) ion and 0.01 ng mL^?1 for Cd(II). The effects of potentially interfering ions often found in real samples on the recovery in the determination of cadmium and lead ions in real samples were also investigated. The accuracy of the method was confirmed by analyzing the certified reference materials NIST 1571 (orchard leaves) and NIST 1572 (citrus leaves). Finally, the method was successfully applied to the determination of cadmium and lead ions in some fruit samples. Figure

We report on a new sorbent for preconcentration of cadmium and lead ions that is based on triazine-functionalized magnetite nanoparticles. After optimization of the preconcentration step the method was successfully applied to the determination of cadmium and lead ions in some fruit samples     

Preconcentration of Metal Ions with Anion-Exchange Resin

A method to preconcentrate metal ions employed an anion-exchange resin was studied. Metal ions were first chelated with ethylenediaminetetraacetic acid (EDTA), then trapped on an enrichment column packed with anion-exchange resin. The major interfering ions, e.g. calcium and magnesium were excluded from enrichment by appropriate adjustment of pH. Desorption of the trapped metals was effected by elution with HCl (0.1 M). Recoveries of Cu²⁺, Ni²⁺, Co²⁺, Pb²⁺, Zn²⁺ reached 99%. By comparison with preconcentration methods using cation-exchange resin, this method has the advantages of selectivity, quantitative recovery, small cost of operation, and simple procedure.     

Measurement of Chelating Agent Levels in Media with High Concentrations of Interfering Metal Ions

Abstract

An ion-exchange method for the measurement of levels of chelating agents in media with high levels of metal ions has been developed. The test solution is passed through a specially prepared ion-exchange column, which both removes metal ion interferences, and places the chelating agent in the copper form. The copper levels in the column effluent are then measured by flame atomic absorption methods, the copper levels corresponding in a 1:1 ratio to the levels of chelating agent in the sample. The detection limit for this method is on the order of 1 ppm copper equivalent chelating capacity, and is applicable in situations where the interfering metal ions are at concentrations in the range of 10^?2 M. The method is reproducible in the pH ranges of 4 to 9 Precision and     

The electrochemical determination of ammonium based on the selective inhibition of the low-spin iron(II)/(III) system of Prussian blue

A new method is described for the determination of ammonium in aqueous solutions with electrodes modified by Prussian blue (PB). The specific voltammetric response of PB-modified electrodes to ammonium ions is used for their analytical determination. In the presence of ammonium ions, a concentration-dependent inhibition of the low-spin iron(II/III) system of PB occurs. Only thallium and rubidium ions cause similar inhibition. A useful electrochemical determination method is thus available for detecting ammonium ions in the presence of frequently interfering potassium and sodium ions. Paraffin-impregnated graphite electrodes modified with a mechanically transferred PB layer and bulk-modified PB-composite electrodes are studied. The method is applicable within a concentration range which extends from 4 × 10⁻⁵ mol/l to 10⁻² mol/l NH₄ ⁺. The composite electrode is used in an electrochemical flow-through system in conjunction with the Kjeldahl method. Received: 21 April 1997 / Accepted: 28 May 1997     

Potentiometric Sensing of Heavy Metal Ions Using a Novel Zeolite Y Membrane

The application of zeolite Y membranes to the potentiometric sensing of heavy metal ions is described. Membranes are prepared from a pressed disk of zeolite Y, treated using tetraethyl orthosilicate (TEOS) as a silica source. The resulting silica‐zeolite Y composite membranes are characterized by powder X‐ray diffraction, MAS NMR and their potentiometric response to cations with a diameter greater than the zeolite Y pore. The initial response to cadmium (Cd²⁺) and lead (Pb²⁺) ions obeys the Nernst equation, including appropriate corrections for non‐ideality, although the responses decay over a time‐scale of several hours for higher concentration ratios.     

Ex Situ Scanning Electrochemical Microscopy (SECM) Investigation of Bismuth‐ and Bismuth/Lead Alloy Film‐Modified Gold Electrodes in Alkaline Medium

Scanning electrochemical microscopy (SECM) in feedback mode was employed to characterise the reactivity and microscopic peculiarities of bismuth and bismuth/lead alloys plated onto gold disk substrates in 0.1 mol L^?1 NaOH solutions. Methyl viologen was used as redox mediator, while a platinum microelectrode was employed as the SECM tip. The metal films were electrodeposited ex situ from NaOH solutions containing either bismuth ions only or both bismuth and lead ions. Approach curves and SECM images indicated that the metal films were conductive and locally reactive with oxygen to provide Bi³⁺ and Pb²⁺ ions. The occurrence of the latter chemical reactions was verified by local anodic stripping voltammetry (ASV) at the substrate solution interface by using a mercury‐coated platinum SECM tip. The latter types of measurements allowed also verifying that lead was not uniformly distributed onto the bismuth film electrode substrate. These findings were confirmed by scanning electron microscopy images. The surface heterogeneity produced during the metal deposition process, however, did not affect the analytical performance of the bismuth coated gold electrode in anodic stripping voltammetry for the determination of lead in alkaline media, even in aerated aqueous solutions. Under the latter conditions, stripping peak currents proportional to lead concentration with a satisfactory reproducibility (within 5 % RSD) were obtained.     

A highly sensitive and selective method for the extraction-spectrophotometric determination of cobalt

The method is based on the highly sensitive reaction between cobalt and 4-(5-bromo-2-pyridylazo)-l,3-diaminobenzene. The cationic complex in slightly acidic solution is quantitatively extracted into chloroform as an ion pair with anthraquinone sulfonate; interfering ions are retained in the aqueous phase by selected masking agents. The cobalt complex is then rapidly back-extracted into 2.4 M HCl and measured at 573 nm (? = 1.16 × 10⁵ l mol^-1 cm^-1).     

Short-term influence of interfering ion activity change on ion-selective micropipette electrode potential; another factor that can affect the time needed for imaging in potentiometric SECM

The applicability of ion-selective microelectrodes (ISME) in scanning electrochemical microscopy (SECM) in the presence of potentially interfering ions is investigated. Decreasing the time needed for potentiometric SECM imaging is a key aim. It is generally accepted that the long response time of potentiometric cells with high impedance microelectrodes limits the imaging speed that can be obtained without distortion. In this study we show that a change in the activity of interfering ions can result in a short-term electrode potential transient that should be taken into consideration in parameter setting for SECM measurements. The activity step method was employed, using NH₄⁺-ion-measuring micropipettes. Solutions containing equal concentrations of NH₄⁺ ions with or without K⁺ ions were rapidly introduced and the short-term change in electrode potential was recorded. Rapid transient potential signals appeared following the K⁺ activity step in the range where the interfering K⁺ did not affect the long-term electrode potential. The possible influence of this on SECM applications is discussed.