Reduced Graphene Oxide‐Supported TiO2 Fiber Bundles with Mesostructures as Anode Materials for Lithium‐Ion Batteries

Although the synthesis of mesoporous materials is well established, the preparation of TiO₂ fiber bundles with mesostructures, highly crystalline walls, and good thermal stability on the RGO nanosheets remains a challenge. Herein, a low‐cost and environmentally friendly hydrothermal route for the synthesis of RGO nanosheet‐supported anatase TiO₂ fiber bundles with dense mesostructures is used. These mesostructured TiO₂‐RGO materials are used for investigation of Li‐ion insertion properties, which show a reversible capacity of 235 mA h g^?1 at 200 mA g^?1 and 150 mA h g^?1 at 1000 mA g^?1 after 1000 cycles. The higher specific surface area of the new mesostructures and high conductive substrate (RGO nanosheets) result in excellent lithium storage performance, high‐rate performance, and strong cycling stability of the TiO₂‐RGO composites.     

A Robust Solid Electrolyte Interphase Layer Augments the Ion Storage Capacity of Bimetallic‐Sulfide‐Containing Potassium‐Ion Batteries

Metal–organic framework‐derived NiCo_2.5S₄ microrods wrapped in reduced graphene oxide (NCS@RGO) were synthesized for potassium‐ion storage. Upon coordination with organic potassium salts, NCS@RGO exhibits an ultrahigh initial reversible specific capacity (602 mAh g^?1 at 50 mA g^?1) and ultralong cycle life (a reversible specific capacity of 495 mAh g^?1 at 200 mA g^?1 after 1 900 cycles over 314 days). Furthermore, the battery demonstrates a high initial Coulombic efficiency of 78 %, outperforming most sulfides reported previously. Advanced ex situ characterization techniques, including atomic force microscopy, were used for evaluation and the results indicate that the organic potassium salt‐containing electrolyte helps to form thin and robust solid electrolyte interphase layers, which reduce the formation of byproducts during the potassiation–depotassiation process and enhance the mechanical stability of electrodes. The excellent conductivity of the RGO in the composites, and the robust interface between the electrodes and electrolytes, imbue the electrode with useful properties; including, ultrafast potassium‐ion storage with a reversible specific capacity of 402 mAh g^?1 even at 2 A g^?1.     

Reducing the Charge Carrier Transport Barrier in Functionally Layer‐Graded Electrodes

Lithium‐ion batteries (LIBs) are primary energy storage devices to power consumer electronics and electric vehicles, but their capacity is dramatically decreased at ultrahigh charging/discharging rates. This mainly originates from a high Li‐ion/electron transport barrier within a traditional electrode, resulting in reaction polarization issues. To address this limitation, a functionally layer‐graded electrode was designed and fabricated to decrease the charge carrier transport barrier within the electrode. As a proof‐of‐concept, functionally layer‐graded electrodes composing of TiO₂(B) and reduced graphene oxide (RGO) exhibit a remarkable capacity of 128 mAh g⁻¹ at a high charging/discharging rate of 20 C (6.7 A g⁻¹), which is much higher than that of a traditionally homogeneous electrode (74 mAh g⁻¹) with the same composition. This is evidenced by the improvement of effective Li ion diffusivity as well as electronic conductivity in the functionally layer‐graded electrodes.     

Zinc‐Reduced Mesoporous TiOx Li‐Ion Battery Anodes with Exceptional Rate Capability and Cycling Stability

We demonstrate a unique synthetic route for oxygen‐deficient mesoporous TiO_x by a redox–transmetalation process by using Zn metal as the reducing agent. The as‐obtained materials have significantly enhanced electronic conductivity; 20 times higher than that of as‐synthesized TiO₂ material. Moreover, electrochemical impedance spectroscopy (EIS) and galvanostatic intermittent titration technique (GITT) measurements are performed to validate the low charge carrier resistance of the oxygen‐deficient TiO_x. The resulting oxygen‐deficient TiO_x battery anode exhibits a high reversible capacity (～180 mA h g^?1 at a discharge/charge rate of 1 C/1 C after 400 cycles) and an excellent rate capability (～90 mA h g^?1 even at a rate of 10 C). Also, the full cell, which is coupled with a LiCoO₂ cathode material, exhibits an outstanding rate capability (>75 mA h g^?1 at a rate of 3.0 C) and maintains a reversible capacity of over 100 mA h g^?1 at a discharge/charge of 1 C/1 C for 300 cycles.     

Amidation‐Dominated Re‐Assembly Strategy for Single‐Atom Design/Nano‐Engineering: Constructing Ni/S/C Nanotubes with Fast and Stable K‐Storage

An amidation‐dominated re‐assembly strategy is developed to prepare uniform single atom Ni/S/C nanotubes. In this re‐assembly process, a single‐atom design and nano‐structured engineering are realized simultaneously. Both the NiO₅ single‐atom active centers and nanotube framework endow the Ni/S/C ternary composite with accelerated reaction kinetics for potassium‐ion storage. Theoretical calculations and electrochemical studies prove that the atomically dispersed Ni could enhance the convention kinetics and decrease the decomposition energy barrier of the chemically‐absorbed small‐molecule sulfur in Ni/S/C nanotubes, thus lowering the electrode reaction overpotential and resistance remarkably. The mechanically stable nanotube framework could well accommodate the volume variation during potassiation/depotassiation process. As a result, a high K‐storage capacity of 608 mAh g^?1 at 100 mA g^?1 and stable cycling capacity of 330.6 mAh g^?1 at 1000 mA g^?1 after 500 cycles are achieved.     

Compositing Amorphous TiO2 with N‐Doped Carbon as High‐Rate Anode Materials for Lithium‐Ion Batteries

Compositing amorphous TiO₂ with nitrogen‐doped carbon through Ti? N bonding to form an amorphous TiO₂/N‐doped carbon hybrid (denoted a‐TiO₂/C? N) has been achieved by a two‐step hydrothermal–calcining method with hydrazine hydrate as an inhibitor and nitrogen source. The resultant a‐TiO₂/C? N hybrid has a surface area as high as 108 m² g^?1 and, when used as an anode material, exhibits a capacity as high as 290.0 mA h g^?1 at a current rate of 1 C and a reversible capacity over 156 mA h g^?1 at a current rate of 10 C after 100 cycles; these results are better than those found in most reports on crystalline TiO₂. This superior electrochemical performance could be ascribed to a combined effect of several factors, including the amorphous nature, porous structure, high surface area, and N‐doped carbon.     

A Self‐Standing and Flexible Electrode of Yolk–Shell CoS2 Spheres Encapsulated with Nitrogen‐Doped Graphene for High‐Performance Lithium‐Ion Batteries

Flexible lithium‐ion batteries (LIBs) have recently attracted increasing attention with the fast development of bendable electronic systems. Herein, a facile and template‐free solvothermal method is presented for the fabrication of hybrid yolk–shell CoS₂ and nitrogen‐doped graphene (NG) sheets. The yolk–shell architecture of CoS₂ encapsulated with NG coating is designed for the dual protection of CoS₂ to address the structural and interfacial stability concerns facing the CoS₂ anode. The as‐prepared composite can be assembled into a film, which can be used as a binder‐free and flexible electrode for LIBs that does not require any carbon black conducting additives or current collectors. When evaluating lithium‐storage properties, such a flexible electrode exhibits a high specific capacity of 992 mAh g^?1 in the first reversible discharge capacity at a current rate of 100 mA g^?1 and high reversible capacity of 882 mAh g^?1 after 150 cycles with excellent capacity retention of 89.91 %. Furthermore, a reversible capacity as high as 655 mAh g^?1 is still achieved after 50 cycles even at a high rate of 5 C due to the yolk–shell structure and NG coating, which not only provide short Li‐ion and electron pathways, but also accommodate large volume variation.     

Three‐Dimensional Fe2N@C Microspheres Grown on Reduced Graphite Oxide for Lithium‐Ion Batteries and the Li Storage Mechanism

Nanostructured iron compounds as lithium‐ion‐battery anode material have attracted considerable attention with respect to improved electrochemical energy storage and excellent specific capacity, so lots of iron‐based composites have been developed. Herein, a novel composite composed of three‐dimensional Fe₂N@C microspheres grown on reduced graphite oxide (denoted as Fe₂N@C‐RGO) has been synthesized through a simple and effective technique assisted by a hydrothermal and subsequent heating treatment process. As the anode material for lithium‐ion batteries, the synthetic Fe₂N@C‐RGO displayed excellent Li⁺‐ion storage performance with a considerable initial capacity of 847 mAh g^?1, a superior cycle stability (a specific discharge capacity of 760 mAh g^?1 remained after the 100th cycle), and an improved rate‐capability performance compared with those of the pure Fe₂N and Fe₂N‐RGO nanostructures. The good performance should be attributed to the existence of RGO layers that can facilitate to enhance the conductivity and shorten the lithium‐ion diffusion path; in addition, the carbon layer on the surface of Fe₂N can avert the structure decay caused by the volume change during the lithiation/delithiation process. Moreover, in situ X‐ray absorption fine‐structure analysis demonstrated that the excellent performance can be attributed to the lack of any obvious change in the coordination geometry of Fe₂N@C‐RGO during the charge/discharge processes.     

MoS2 Nanoflowers with Expanded Interlayers as High‐Performance Anodes for Sodium‐Ion Batteries

MoS₂ nanoflowers with expanded interlayer spacing of the (002) plane were synthesized and used as high‐performance anode in Na‐ion batteries. By controlling the cut‐off voltage to the range of 0.4–3 V, an intercalation mechanism rather than a conversion reaction is taking place. The MoS₂ nanoflower electrode shows high discharge capacities of 350 mAh g^?1 at 0.05 A g^?1, 300 mAh g^?1 at 1 A g^?1, and 195 mAh g^?1 at 10 A g^?1. An initial capacity increase with cycling is caused by peeling off MoS₂ layers, which produces more active sites for Na⁺ storage. The stripping of MoS₂ layers occurring in charge/discharge cycling contributes to the enhanced kinetics and low energy barrier for the intercalation of Na⁺ ions. The electrochemical reaction is mainly controlled by the capacitive process, which facilitates the high‐rate capability. Therefore, MoS₂ nanoflowers with expanded interlayers hold promise for rechargeable Na‐ion batteries.     

TiO2 Microboxes with Controlled Internal Porosity for High‐Performance Lithium Storage

Titanium dioxide (TiO₂) is considered a promising anode material for high‐power lithium ion batteries (LIBs) because of its low cost, high thermal/chemical stability, and good safety performance without solid electrolyte interface formation. However, the poor electronic conductivity and low lithium ion diffusivity of TiO₂ result in poor cyclability and lithium ion depletion at high current rates, which hinder them from practical applications. Herein we demonstrate that hierarchically structured TiO₂ microboxes with controlled internal porosity can address the aforementioned problems for high‐power, long‐life LIB anodes. A self‐templating method for the synthesis of mesoporous microboxes was developed through Na₂EDTA‐assisted ion exchange of CaTiO₃ microcubes. The resulting TiO₂ nanorods were organized into microboxes that resemble the microcube precursors. This nanostructured TiO₂ material has superior lithium storage properties with a capacity of 187 mAh g⁻¹ after 300 cycles at 1 C and good rate capabilities up to 20 C.     

One‐Pot Fabrication of Hierarchical Nanosheet‐Based TiO2–Carbon Hollow Microspheres for Anode Materials of High‐Rate Lithium‐Ion Batteries

Hierarchical and hollow nanostructures have recently attracted considerable attention because of their fantastic architectures and tunable property for facile lithium ion insertion and good cycling stability. In this study, a one‐pot and unusual carving protocol is demonstrated for engineering hollow structures with a porous shell. Hierarchical TiO₂ hollow spheres with nanosheet‐assembled shells (TiO₂ NHS) were synthesized by the sequestration between the titanium source and 2,2′‐bipyridine‐5,5′‐dicarboxylic acid, and kinetically controlled etching in trifluoroacetic acid medium. In addition, annealing such porous nanostructures presents the advantage of imparting carbon‐doped functional performance to its counterpart under different atmospheres. Such highly porous structures endow very large specifics surface area of 404 m² g^?1 and 336 m² g^?1 for the as‐prepared and calcination under nitrogen gas. C/TiO₂ NHS has high capacity of 204 mA h g^?1 at 1 C and a reversible capacity of 105 mA h g^?1 at a high rate of 20 C, and exhibits good cycling stability and superior rate capability as an anode material for lithium‐ion batteries.     

Electrochemical Properties of Fiber‐in‐Tube‐ and Filled‐Structured TiO2 Nanofiber Anode Materials for Lithium‐Ion Batteries

Phase‐pure anatase TiO₂ nanofibers with a fiber‐in‐tube structure were prepared by the electrospinning process. The burning of titanium‐oxide‐carbon composite nanofibers with a filled structure formed as an intermediate product under an oxygen atmosphere produced carbon‐free TiO₂ nanofibers with a fiber‐in‐tube structure. The sizes of the nanofiber core and hollow nanotube were 140 and 500 nm, respectively. The heat treatment of the electrospun nanofibers at 450 and 500 °C under an air atmosphere produced grey and white filled‐structured TiO₂ nanofibers, respectively. The initial discharge capacities of the TiO₂ nanofibers with the fiber‐in‐tube and filled structures and the commercial TiO₂ nanopowders were 231, 134, and 223 mA h g^?1, respectively, and their corresponding charge capacities were 170, 100, and 169 mA h g^?1, respectively. The 1000th discharge capacities of the TiO₂ nanofibers with the fiber‐in‐tube and filled structures and the commercial TiO₂ nanopowders were 177, 64, and 101 mA h g^?1, respectively, and their capacity retentions measured from the second cycle were 89, 82, and 52 %, respectively. The TiO₂ nanofibers with the fiber‐in‐tube structure exhibited low charge transfer resistance and structural stability during cycling and better cycling and rate performances than the TiO₂ nanofibers with filled structures and the commercial TiO₂ nanopowders.     

Low‐Temperature Synthesis of Honeycomb CuP2@C in Molten ZnCl2 Salt for High‐Performance Lithium Ion Batteries

Phosphorus‐rich metal phosphides have very high lithium storage capacities, but they are difficult to prepare. A low‐temperature phosphorization method based on Mg reducing PCl₃ in ZnCl₂ molten salt at 300 °C is developed to synthesize phosphorus‐rich CuP₂@C from a Cu‐MOF derived Cu@C composite. Abnormal oxidation of Cu by Zn²⁺ in the molten salt is observed, which leads to the porous honeycomb nanostructure and homogeneously distributed ultrafine CuP₂ nanocrystals. The honeycomb CuP₂@C exhibits excellent lithium storage performance with high reversible capacity (1146 mAh g^?1 at 0.2 A g^?1) and superior cycling stability (720 mAh g^?1 after 600 cycles at 1.0 A g^?1), showing the promising application of P‐rich metal phosphides in lithium ion batteries.     

One‐Step Pyro‐Synthesis of a Nanostructured Mn3O4/C Electrode with Long Cycle Stability for Rechargeable Lithium‐Ion Batteries

A nanostructured Mn₃O₄/C electrode was prepared by a one‐step polyol‐assisted pyro‐synthesis without any post‐heat treatments. The as‐prepared Mn₃O₄/C revealed nanostructured morphology comprised of secondary aggregates formed from carbon‐coated primary particles of average diameters ranging between 20 and 40 nm, as evidenced from the electron microscopy studies. The N₂ adsorption studies reveal a hierarchical porous feature in the nanostructured electrode. The nanostructured morphology appears to be related to the present rapid combustion strategy. The nanostructured porous Mn₃O₄/C electrode demonstrated impressive electrode properties with reversible capacities of 666 mAh g^?1 at a current density of 33 mA g^?1, good capacity retentions (1141 mAh g^?1 with 100 % Coulombic efficiencies at the 100^th cycle), and rate capabilities (307 and 202 mAh g^?1 at 528 and 1056 mA g^?1, respectively) when tested as an anode for lithium‐ion battery applications.     

Biomass‐Derived Porous Carbon with Micropores and Small Mesopores for High‐Performance Lithium–Sulfur Batteries

Biomass‐derived porous carbon BPC‐700, incorporating micropores and small mesopores, was prepared through pyrolysis of banana peel followed by activation with KOH. A high specific BET surface area (2741 m² g^?1), large specific pore volume (1.23 cm³ g^?1), and well‐controlled pore size distribution (0.6–5.0 nm) were obtained and up to 65 wt % sulfur content could be loaded into the pores of the BPC‐700 sample. When the resultant C/S composite, BPC‐700‐S65, was used as the cathode of a Li–S battery, a large initial discharge capacity (ca. 1200 mAh g^?1) was obtained, indicating a good sulfur utilization rate. An excellent discharge capacity (590 mAh g^?1) was also achieved for BPC‐700‐S65 at the high current rate of 4 C (12.72 mA cm^?2), showing its extremely high rate capability. A reversible capacity of about 570 mAh g^?1 was achieved for BPC‐700‐S65 after 500 cycles at 1 C (3.18 mA cm^?2), indicating an outstanding cycling stability.     

Rechargeable Room‐Temperature Na–CO2 Batteries

Developing rechargeable Na–CO₂ batteries is significant for energy conversion and utilization of CO₂. However, the reported batteries in pure CO₂ atmosphere are non‐rechargeable with limited discharge capacity of 200 mAh g^?1. Herein, we realized the rechargeability of a Na–CO₂ battery, with the proposed and demonstrated reversible reaction of 3 CO₂+4 Na?2 Na₂CO₃+C. The battery consists of a Na anode, an ether‐based electrolyte, and a designed cathode with electrolyte‐treated multi‐wall carbon nanotubes, and shows reversible capacity of 60000 mAh g^?1 at 1 A g^?1 (≈1000 Wh kg^?1) and runs for 200 cycles with controlled capacity of 2000 mAh g^?1 at charge voltage <3.7 V. The porous structure, high electro‐conductivity, and good wettability of electrolyte to cathode lead to reduced electrochemical polarization of the battery and further result in high performance. Our work provides an alternative approach towards clean recycling and utilization of CO₂.     

Three‐Dimensional Hierarchical Constructs of MOF‐on‐Reduced Graphene Oxide for Lithium–Sulfur Batteries

A three‐dimensional (3D) hierarchical MOF‐on‐reduced graphene oxide (MOF‐on‐rGO) compartment was successfully synthesized through an in situ reduced and combined process. The unique properties of the MOF‐on‐rGO compartment combining the polarity and porous features of MOFs with the high conductivity of rGO make it an ideal candidate as a sulfur host in lithium–sulfur (Li‐S) batteries. A high initial discharge capacity of 1250 mAh g^?1 at a current density of 0.1 C (1.0 C=1675 mAh g^?1) was reached using the MOF‐on‐rGO based electrode. At the rate of 1.0 C, a high specific capacity of 601 mAh g^?1 was still maintained after 400 discharge–charge cycles, which could be ascribed to the synergistic effect between MOFs and rGO. Both the hierarchical structures of rGO and the polar pore environment of MOF retard the diffusion and migration of soluble polysulfide, contributing to a stable cycling performance. Moreover, the spongy‐layered rGO can buffer the volume expansion and contraction changes, thus supplying stable structures for Li‐S batteries.     

Ascorbic Acid‐Assisted Synthesis of Mesoporous Sodium Vanadium Phosphate Nanoparticles with Highly sp2‐Coordinated Carbon Coatings as Efficient Cathode Materials for Rechargeable Sodium‐Ion Batteries

Herein, mesoporous sodium vanadium phosphate nanoparticles with highly sp²‐coordinated carbon coatings (meso‐Na₃V₂(PO₄)₃/C) were successfully synthesized as efficient cathode material for rechargeable sodium‐ion batteries by using ascorbic acid as both the reductant and carbon source, followed by calcination at 750 °C in an argon atmosphere. Their crystalline structure, morphology, surface area, chemical composition, carbon nature and amount were systematically explored. Following electrochemical measurements, the resultant meso‐Na₃V₂(PO₄)₃/C not only delivered good reversible capacity (98 mAh g^?1 at 0.1 A g^?1) and superior rate capability (63 mAh g^?1 at 1 A g^?1) but also exhibited comparable cycling performance (capacity retention: ≈74 % at 450 cycles at 0.4 A g^?1). Moreover, the symmetrical sodium‐ion full cell with excellent reversibility and cycling stability was also achieved (capacity retention: 92.2 % at 0.1 A g^?1 with 99.5 % coulombic efficiency after 100 cycles). These attributes are ascribed to the distinctive mesostructure for facile sodium‐ion insertion/extraction and their continuous sp²‐coordinated carbon coatings, which facilitate electronic conduction.     

Fiber‐in‐Tube Design of Co9S8‐Carbon/Co9S8: Enabling Efficient Sodium Storage

The sodium‐ion battery is a promising battery technology owing to its low price and high abundance of sodium. However, the sluggish kinetics of sodium ion makes it hard to achieve high‐rate performance, therefore impairing the power density. In this work, a fiber‐in‐tube Co₉S₈‐carbon(C)/Co₉S₈ is designed with fast sodiation kinetics. The experimental and simulation analysis show that the dominating capacitance mechanism for the high Na‐ion storage performance is due to abundant grain boundaries, three exposed layer interfaces, and carbon wiring in the design. As a result, the fiber‐in‐tube hybrid anode shows a high specific capacity of 616 mAh g^?1 after 150 cycles at 0.5 A g^?1. At 1 A g^?1, a capacity of ca. 451 mAh g^?1 can be achieved after 500 cycles. More importantly, a high energy density of 779 Wh kg^?1 and power density of 7793 W kg^?1 can be obtained simultaneously.     

Preparation and electrochemical properties of graphene‐supported Si‐TiO2 nanospheres as anode material for Li‐ion batteries

Graphene‐supported Si‐TiO₂ (Si‐Ti‐GE) composites have been synthesized by a simple polymerization and sintering method. In the Si‐Ti‐GE composites, many small Si‐TiO₂ particles are scattered on the graphene sheet, which can mitigate the agglomeration of the material and further reduce the particle size. The initial discharge capacities of Si‐TiO₂, Si‐Ti‐GE‐1, Si‐Ti‐GE‐2, and Si‐Ti‐GE‐3 are 336.9, 337.2, 339.8, and 356.6 mAh g⁻¹ at the current density of 200 mA g⁻¹, respectively. The discharge rate capacities of TiO₂, Si‐TiO₂, and Si‐Ti‐GE‐3 composites retain 57.5%, 41.7%, and 82.1% at the current density from 100 to 400 mA g⁻¹, respectively. Therefore, the introduction of graphene not only could facilitate the Li⁺ diffusion and electron transport but also could make better electrical conductivity.