有机/无机复合介孔膜的合成及其生物酶吸附行为研究

以正硅酸四乙酯(TEOS)为硅源、三嵌段共聚物(F127)为表面活性剂,聚碳酸酯膜为硬模板,并采用抽滤法在聚碳酸酯膜内的亚微米级孔道中组装介孔氧化硅从而制备出有机(聚碳酸酯)/无机(介孔氧化硅)复合介孔膜.通过扫描电镜、能量分散光谱以及透射电镜等实验表征了该有机/无机复合介孔膜的组成、结构及形貌.研究结果表明:通过该方法可以在聚碳酸酯膜内孔道中形成长度为9μm、直径为200nm的一维氧化硅棒状材料,且该棒状材料具有无序蠕虫状和有序体心立方的混合介孔结构,有序体心立方介孔的平均孔径约为8.5nm.另外,初步考察了该复合介孔膜对生物酶的物理吸附行为,结果表明其对肌红蛋白酶的单位吸附负载量为5.85mg/g.     

可用于色谱固定相的介孔氧化硅球材料的合成

采用非离子型嵌段高分子表面活性剂EO₂₀PO₃₀EO₂₀ (P65)为结构导向剂, 正硅酸乙酯为硅源, 在酸性介质中, 静置法制备了微米级介孔氧化硅球. 通过改变合成温度、反应时间或者无机盐KCl的加入量, 可以调节介孔氧化硅球的直径(9.0～17.6 μm); 加入1,3,5-三甲苯(TMB)或者调节水热温度, 可以调节介孔氧化硅球的孔径(2.3～4.8 nm). 采用X射线衍射(XRD)、N₂吸附-脱附、扫描电镜(SEM)、激光散射粒度分布和对溶菌酶的吸附等方法, 对介孔氧化硅球的结构、孔性质、形貌、吸附性质等进行了表征. 实验发现, 孔径较小的介孔氧化硅球(≤4.3 nm)对溶菌酶的吸附不明显(≤42 mg/g), 而孔径(4.8 nm)大于溶菌酶直径的材料对溶菌酶有较大的吸附量(192 mg/g), 说明孔径均匀可调的介孔氧化硅球材料可以很好地用作体积排阻色谱柱的固定相.     

分子印迹功能介孔材料富集-火焰原子吸收光谱法测定溶液中痕量铅

以2-巯基苯骈噻唑为修饰剂,铅离子为印迹离子成功制备分子印迹功能介孔材料,并用扫描电镜(SEM)、傅里叶红外光谱对材料进行了结构表征。铅离子分子印迹功能介孔材料能很好地将Pb(II)与性质相近的二价重金属离子Cu(II),Cd(II)和Hg(II)分离,具有非常好的吸附选择性,且静态吸附容量0.64 mmol/g。利用该材料制备的分离富集柱可以很好地富集溶液中痕量铅离子,且仅用2 mL 0.5 mol/L EDTA以0.4 mL/min流速即可完全洗脱,富集倍数高达250倍。样品预富集后的火焰原子吸收光度法线性范围为0.5～1.2×104μg/L,r=0.999 2,检出限(3σ,n=11)为0.04μg/L。利用功能介孔材料分离富集水样中痕量铅离子,用火焰原子吸收法测定含量,相对标准偏差(RSD)小于等于3%(n=6),回收率在98.2%～99.1%之间。     

陈化温度和pH值对氨基功能化介孔氧化硅吸附CO_2性能的影响

本研究采用溶胶-凝胶法,分别以十二烷基肌氨酸钠、氨丙基三甲氧基硅烷(APTMS)和正硅酸乙酯(TEOS)为结构导向剂(SDA)、共结构导向剂(CSDA)和硅源合成了氨基功能化的介孔氧化硅预产物。利用乙醇和乙醇胺混合液对预产物进行萃取后获得氨基功能化介孔氧化硅。利用红外光谱、元素分析、N2吸-脱附、透射电镜等手段对材料进行了表征。红外光谱结果证明通过萃取方法可较好地去除表面活性剂;N2吸附结果表明所有样品都具有介孔结构;元素分析和透射电镜结果说明反应陈化温度、pH值等合成条件对材料孔道内表面的氨基含量和材料结构有较大的影响。CO2吸附实验证明在低陈化温度、相对较低的pH值下合成的材料具有较高的CO2吸附量。     

疏水二氧化硅气凝胶对甲苯蒸气吸附性能研究

吸附法是控制挥发性有机物(VOCs)的重要方法,对吸附材料的研究有着重要的意义。为了开发出吸附量高、稳定性好的吸附材料,利用溶胶-凝胶法制备出疏水二氧化硅气凝胶,并对其进行了低温氮气吸附、傅里叶变换红外光谱和热重分析,同时对疏水二氧化硅气凝胶进行了甲苯蒸气的静态、动态和循环吸附实验,研究其对甲苯蒸气的吸附性能。结果表明,所制疏水二氧化硅气凝胶为比表面积达732m~2/g的介孔吸附材料,其表面具有疏水性甲基基团,吸附容量高达1.6g/g,吸附稳定性强,动态吸附温升最高达12℃,用Logistic模型拟合吸附穿透曲线相似度高。     

二氧化硅气凝胶对挥发性有机污染物的吸附性能研究

以TEOS为前驱体,乙醇为溶剂,氢氟酸为催化剂,一步法合成了常规二氧化硅气凝胶。经乙醇超临界干燥后,通过SEM,FTIR和N2吸脱附分析仪等仪器对二氧化硅气凝胶样品进行表征,以更好地了解吸附机理与性质的关系。结果表明,样品的比表面积高达519 m2/g,孔体积为1.9 cm3/g,平均孔径为15.15 nm,是一种优良的吸附材料。制备的样品用作测试甲苯、对二甲苯和苯三种挥发性有机化合物的吸附效果。结果表明,二氧化硅气凝胶对三种污染物都具有很高的吸附量,其高吸附能力归因于气凝胶的三维纳米网络结构。样品对甲苯,对二甲苯和苯的最大吸附能力分别为1422.8 mg/g,707.4 mg/g和1299.4 mg/g。综上所述,二氧化硅气凝胶是一种很有前景的处理挥发性有机化合物的吸附剂,具有优异的吸附性能。     

高性能钛酸锂/还原氧化石墨烯复合负极材料的合成与应用

通过简单的水热法制备了具有介孔结构的钛酸锂/还原氧化石墨烯(LTO/RGO)负极材料,并对该材料的结构及形貌进行了表征.结果表明,该方法获得的LTO/RGO负极材料具有高的比表面积且钛酸锂纳米片不易团聚.电化学性能测试结果表明,该材料在0. 1C倍率下的初始放电比容量达到182. 2 mA·h/g;在5C倍率下经过500周循环后容量仍保持在160. 6 mA·h/g,表现出较好的循环性能.     

超高容量氧化石墨烯/碳纳米管气凝胶用于血红蛋白的吸附分离

采用冷冻干燥技术制备了三维氧化石墨烯/碳纳米管(GO/CNTs)气凝胶,在疏水作用下,该气凝胶对蛋白质表现出良好的吸附性能.在p H=8.0时,GO/CNTs气凝胶对血红蛋白的吸附效率很高,而对白蛋白基本不吸附,从而可实现血红蛋白的选择性吸附分离.在最佳吸附条件下,GO/CNTs气凝胶对血红蛋白的吸附容量高达3793.3 mg/g,是去除高丰度血红蛋白的高效材料.吸附后的血红蛋白可以使用p H=11.5的BrittonRobisin缓冲液有效洗脱,回收率为67%.圆二色光谱结果表明,GO/CNTs气凝胶具有良好的生物相容性,其表面发生的吸附/洗脱过程对血红蛋白的构象基本无影响.将GO/CNTs气凝胶用于人全血样品中血红蛋白的选择性分离,SDS-聚丙烯酰胺凝胶电泳结果表明得到了较高纯度的血红蛋白.     

介孔硅复合氧化石墨烯多孔材料的制备及其CO2吸附性能研究

以P123为模板剂,以TEOS为硅源,以氧化石墨烯为复合组分,采用溶胶-凝胶法和自组装法制备了具有较大比表面积的介孔硅复合氧化石墨烯三维多孔材料（MSM/GOs）,进一步通过物理浸渍聚乙烯亚胺（PEI）制备了固态胺吸附材料。利用扫描电子显微镜（SEM）、氮气吸附-脱附曲线、元素分析等方法表征复合材料的结构和形貌,研究了氧化石墨烯添加量对材料的比表面积和胺化效果的影响以及吸附温度对其吸附CO₂性能的影响。研究结果表明,氧化石墨烯的引入能显著提高介孔硅复合氧化石墨烯多孔材料的比表面积,当GO添加量为4.5wt%时,其比表面积可高达841m²/g。高的比表面积有利于提高材料的氨基含量。在30wt%PEI的物理浸渍胺化后,MSM/GO-4.5@30%PEI拥有最大含氮量（9.59wt%）和CO₂吸附量（1.70mmol/g）。得益于良好的多孔基体和有机胺的均匀分布,MSM/GO-4.5@30%PEI在不同温度下的吸附量较稳定,循环再生吸附后仍能保持初始吸附量的80%。动力学研究表明,准一级模型和Avrami模型均能较好地拟合其吸...     

镁热还原CO2气体制备介孔石墨烯及其电容特性研究

以CO_2为原料,采用金属镁热还原法,制备出富含介孔结构的石墨烯材料。分别利用X射线衍射、扫描电镜、透射电镜、拉曼光谱和N_2吸附-脱附等测试手段对材料的微观结构进行了表征。通过在镁粉中加入不同质量的MgO,可以实现对石墨烯形貌和孔结构的调控,当MgO/Mg质量比为8∶1时,产物(MRG-8)具有均一的介孔结构(4nm)。并对材料的电化学性能进行了测试,在1mol/L KOH的电解液中,MRG-8具有最高的比电容(171F/g),同时具有非常好的倍率特性,循环测试12000周,比电容保持率为94%。当采用[EMIM][BF4]离子液体作为电解液,以MRG-8为电极材料组装成的对称型超级电容器显示出超高功率密度(175k W/kg),对应的能量密度为28.1Wh/kg。因此,采用此方法制备的介孔石墨烯材料在高功率的超级电容器领域具有潜在的应用前景。     

In situ self‐assembled reduced graphene oxide aerogel embedded with nickel oxide nanoparticles for the high‐efficiency separation of ovalbumin

A three‐dimensional reduced graphene oxide aerogel with embedded nickel oxide nanoparticles was prepared by a one‐step self‐assembly reaction in a short time. The nanoparticles could be captured into the interior of reduced graphene oxide network during the formation of the three‐dimensional architecture. The composite exhibited porosity, good biocompatibility, and abundant metal affinity binding sites. The aerogel was used to isolate ovalbumin selectively from egg white, and favorable adsorption was achieved at pH 3. An adsorption efficiency of 90.6% was obtained by using 1 mg of the composite for adsorbing 70 μg/mL of ovalbumin in 1.0 mL of sample solution, and afterwards a recovery of 90.7% was achieved by using an eluent of 1.0 mL Britton–Robinson buffer solution at pH 5. After the adsorption/desorption, ovalbumin showed no change in the conformation. The adsorption behavior of ovalbumin on the reduced graphene oxide composite well fitted to the Langmuir adsorption model, and a corresponding theoretical maximum adsorption capacity was 1695.2 mg/g. A sodium dodecyl sulfate polyacrylamide gel electrophoresis assay demonstrated that the aerogel could selectively isolate ovalbumin from chicken egg white.     

氨基硅球及其复合材料的合成与金属离子吸附

采用一锅法制备单分散氨基功能化氧化硅球(AFS),再利用水热法合成了AFS石墨烯气凝胶复合材料(AFSGA)。利用X射线衍射、显色反应、扫描电镜、傅里叶红外谱图等手段对AFS和AFSGA进行表征,考察了催化剂用量,有机硅源的种类及硅酸乙酯与硅源的加入比例等因素对AFS的形貌、表面结构与性质,以及对重金属离子吸附性能的影响。采用X射线荧光法测试了AFS和AFSGA对多种重金属离子的吸附特性,二者对Hg_²⁺的吸附量分别为142.3和102.84 mg/g。单分散AFS是一种合成流程便捷,应用经济性优异的吸附材料,而超轻、结构稳定性良好的AFSGA更具有易于回收与重复利用的应用优势。     

One‐Pot Synthesis of Pomegranate‐Structured Fe3O4/Carbon Nanospheres‐Doped Graphene Aerogel for High‐Rate Lithium Ion Batteries

A unique hierarchically nanostructured composite of iron oxide/carbon (Fe₃O₄/C) nanospheres‐doped three‐dimensional (3D) graphene aerogel has been fabricated by a one‐pot hydrothermal strategy. In this novel nanostructured composite aerogel, uniform Fe₃O₄ nanocrystals (5–10 nm) are individually embedded in carbon nanospheres (ca. 50 nm) forming a pomegranate‐like structure. The carbon matrix suppresses the aggregation of Fe₃O₄ nanocrystals, avoids direct exposure of the encapsulated Fe₃O₄ to the electrolyte, and buffers the volume expansion. Meanwhile, the interconnected 3D graphene aerogel further serves to reinforce the structure of the Fe₃O₄/C nanospheres and enhances the electrical conductivity of the overall electrode. Therefore, the carbon matrix and the interconnected graphene network entrap the Fe₃O₄ nanocrystals such that their electrochemical function is retained even after fracture. This novel hierarchical aerogel structure delivers a long‐term stability of 634 mA h g^?1 over 1000 cycles at a high current density of 6 A g^?1 (7 C), and an excellent rate capability of 413 mA h g^?1 at 10 A g^?1 (11 C), thus exhibiting great potential as an anode composite structure for durable high‐rate lithium‐ion batteries.     

Three‐Dimensional Macroassembly of Sandwich‐Like,Hierarchical, Porous Carbon/Graphene Nanosheets towards Ultralight,Superhigh Surface Area,Multifunctional Aerogels

A new, ultralight, superhigh surface area, multifunctional aerogel, which is macroassembled from sandwich‐like, hierarchical, porous carbon/graphene nanosheets, is described. The multifunctional aerogel was characterized by means of XRD, SEM, TEM, Raman spectroscopy, and UV/Vis absorption spectroscopy. The multifunctional aerogel had an ultralow density of 8 mg cm^?3 and a superhigh surface area of 2650 m² g^?1. The multifunctional aerogel was thermal stability and compressible. Meanwhile, the multifunctional aerogel exhibited high capacity for the adsorption of oils and organic solvents, unexpectedly high hydrogen adsorption and good electrochemical performance.     

Enhanced Electrocatalytic Performance of a Porous g‐C3N4/Graphene Composite as a Counter Electrode for Dye‐Sensitized Solar Cells

A porous graphitic carbon nitride (g‐C₃N₄)/graphene composite was prepared by a simple hydrothermal method and explored as the counter electrode of dye‐sensitized solar cells (DSCs). The obtained g‐C₃N₄/graphene composite was characterized by XRD, SEM, TEM, FTIR spectroscopy, and X‐ray photoelectron spectroscopy. The results show that incorporating graphene nanosheets into g‐C₃N₄ forms a three‐dimensional architecture with a high surface area, porous structure, efficient electron‐transport network, and fast charge‐transfer kinetics at the g‐C₃N₄/graphene interfaces. These properties result in more electrocatalytic active sites and facilitate electrolyte diffusion and electron transport in the porous framework. As a result, the as‐prepared porous g‐C₃N₄/graphene composite exhibits an excellent electrocatalytic activity. In I^?/I₃^? redox electrolyte, the charge‐transfer resistance of the porous g‐C₃N₄/graphene composite electrode is 1.8 Ω cm², which is much lower than those of individual g‐C₃N₄ (70.1 Ω cm²) and graphene (32.4 Ω cm²) electrodes. This enhanced electrocatalytic performance is beneficial for improving the photovoltaic performance of DSCs. By employing the porous g‐C₃N₄/graphene composite as the counter electrode, the DSC achieves a conversion efficiency of 7.13 %. This efficiency is comparable to 7.37 % for a cell with a platinum counter electrode.     

3D Nitrogen-Doped Graphene Encapsulated Metallic Nickel–Iron Alloy Nanoparticles for Efficient Bifunctional Oxygen Electrocatalysis

It is extremely desirable to explore high-efficient, affordable and robust oxygen electrocatalysts toward rechargeable Zn–air batteries (ZABs). A 3D porous nitrogen-doped graphene encapsulated metallic Ni₃Fe alloy nanoparticles aerogel (Ni₃Fe-GA₁) was constructed through a facile hydrothermal assembly and calcination process. Benefiting from 3D porous configuration with great accessibility, high electrical conductivity, abundant active sites, optimal nitrogen content and strong electronic interactions at the Ni₃Fe/N-doped graphene heterointerface, the obtained aerogel showed outstanding catalytic performance toward the oxygen evolution reaction (OER) and oxygen reduction reaction (ORR). Specifically, it exhibited an overpotential of 239 mV to attain 10 mA cm⁻² for OER, simultaneously providing a positive onset potential of 0.93 V within a half-wave potential of 0.8 V for ORR. Accordingly, when employed in the aqueous ZABs, Ni₃Fe-GA₁ achieved higher power density and superior reversibility than Pt/C−IrO₂ catalyst, making it a potential candidate for rechargeable ZABs.     

Electrocatalytic Activity of Immobilized Co(II) on Porous Graphene Aerogels

The highly‐porous graphene aerogel (GA) with BET surface area of 810 m² g^?1 and three‐dimensional structure has been successfully fabricated using the hydrothermal technique. The modified glassy carbon electrode was then prepared by casting the graphene aerogel solution followed by immersing the GA/GCE in Co⁺² solution. The results showed that graphene aerogels improved the adsorption ability of the Co (II) ions. The electrocatalysis of oxygen evolution reaction (OER) at the Co‐GA modified glassy carbon elec‐ trode (Co‐GA/GCE) has been investigated using linear sweep voltammetry (LSV) in alkaline solution. The OER was noticeably enhanced at Co‐GA/GCE, representing a negative shift in the LSV curve at the Co‐GA/GCE compared to that obtained at the bare GCE. The high electrocatalytic activity, good reproducibility and low cost of proposed electrode provides desired characteristics of a potential candi‐ date in the industrial water electrolysis process.     

Porous multicomponent chitosan/poly(ε-caprolactone)-block poly (ethylene glycol)/SiO2 aerogel@polydopamine membrane for Congo red adsorption

A composite adsorbent, chitosan//poly (ε-caprolactone)-block poly (ethylene glycol)/SiO₂ aerogel@polydopamine (CS/PCL-b-PEG/SA@PDA) membrane was prepared for the adsorption of organic dyes. The matrix polymer materials of this novel adsorbent were eco-friendly. SiO₂ aerogel with nanoporous network construction was fixed in the multicomponent polymer fibers through simultaneous electrospinning-electrospray technology followed by modification of polydopamine (PDA). The composite adsorbent had a maximum adsorption capacity of 598.8 mg/g for Congo red (CR) and possessed good reusability performance. This adsorbent showed excellent performance for the selective adsorption of relatively large molecule CR dyes even under high concentration of small molecule methyl orange (MO) dyes or 1 M of salt solution. The adsorption mechanism indicated that the –NH₂ and –OH groups in adsorbent could generate the stronger electrostatic attraction with the –SO₃^- groups in CR. Meanwhile, the sufficient adsorption spaces of the adsorbent were constructed by the porous network structure of SiO₂ aerogel, the accumulation of PDA particles and the porous structure of the multicomponent composite membrane. The work provided a proactive study in designing an adsorbent for the selective adsorption of organic dyes.     

GO/Fe3O4/有机胺复合材料的制备及对结晶紫染料的吸附性能

用改进的Hummers法制备了氧化石墨烯,用乙二胺、乙二胺与丁二胺/己二胺混溶来改性氧化石墨烯。用水热法制备了Fe3O4,并用物理混合法制备了GO/Fe3O4/有机胺的三元复合体系。用透射电镜、扫描电镜、红外光谱、热重分析、X射线衍射、VSM和XPS等对所制得的样品进行了结构表征和性能测试,研究了三元复合粒子对结晶紫染料的吸附性能及影响结晶紫染料吸附效果的因素。结果表明:所制备的Fe3O4的平均粒径约为200 nm,粒径分布均匀;复合物中GO为典型的片状结构,GO及有机胺的掺杂没有影响Fe3O4的尖晶石结构;复合物为超顺磁性,Ms为53.0 emu·g~(-1)。吸附结果表明:石墨烯/Fe3O4/有机胺的三元复合材料对结晶紫染料的最大吸附量随浓度增大而增大,而吸附结晶紫染料的移除率却随结晶紫染料浓度增大而减小,并趋向一定值;乙二胺和己二胺混溶比例为5∶1的GO/Fe3O4复合材料吸附性能最佳:结晶紫浓度为400 mg·L~(-1),最大吸附量为164.3 mg·L~(-1)。     

Platinum-Supported Zirconia Nanotube Arrays Supported on Graphene Aerogels Modified with Metal–Organic Frameworks: Adsorption and Oxidation of Formaldehyde at Room Temperature

Precious-metal catalysts (e.g., Au, Rh, Ag, Ru, Pt, and Pd) supported on transition-metal oxides (e.g., Al₂O₃, Fe₂O₃, CeO₂, ZrO₂, Co₃O₄, MnO₂, TiO₂, and NiO) can effectively oxidize volatile organic compounds. In this study, porous platinum-supported zirconia materials have been prepared by a “surface-casting” method. The synthesized catalysts present an ordered nanotube structure and exhibited excellent performance toward the catalytic oxidation of formaldehyde. A facile method, utilizing a boiling water bath, was used to fabricate graphene aerogel (GA), and the macroscopic 3D Pt/ZrO₂-GA was modified by introducing an adjustable MOF coating by a surface step-by-step method. The unblocked mesoporous structure of the graphene aerogel facilitates the ingress and egress of reactants and product molecules. The selected 7 wt.% Pt/ZrO₂-GA-MOF-5 composite demonstrated excellent performance for HCHO adsorption. Additionally, this catalyst achieved around 90 % conversion when subjected to a reaction temperature of 70 °C (T_{90 %}=70 °C). The Pt/ZrO₂-GA-MOF-5 composite induces a catalytic cycle, increasing the conversion by simultaneously adsorbing and oxidizing HCHO. This work provides a simple approach to increasing reactant concentration on the catalyst to increase the rate of reaction.