聚电解质──壳聚糖浓溶液流变学性质研究：浓度、温度、溶剂pH值和外加盐对粘度及流动性的影响

本工作用日本岩本ＲＰＸ－７０５多功能流变仪测定了在不同浓度，温度，溶剂ｐＨ值和外加盐浓度对壳聚糖在甲酸水溶液中其浓溶液粘度η随剪切速率γ的变化关系，讨论了浓度，温度等对溶液粘度，流动活化能Ｅγ和流动指数ｎ的影响。发现溶剂ｐＨ值减小或溶液中外加盐浓度增加，溶液粘度变小，ｎ增大，表明非牛顿流动性减弱，并且进一步了零剪切粘度ηｏ和外加盐浓度Ｃｓ的依赖关系。     

聚电解质──壳聚糖浓溶液流变学性质研究：浓度、温度、溶剂pH值和外加盐对粘度及流动性的影响

本工作用日本岩本ＲＰＸ－７０５多功能流变仪测定了在不同浓度、温度、溶剂ｐＨ值和外加盐浓度对壳聚糖在甲酸水溶液中其浓溶液粘度η随剪切速率γ的变化关系．讨论了浓度、温度等对溶液粘度、流动活化能Ｅ_γ和流动指数ｎ的影响．发现溶剂ｐＨ值减小或溶液中外加盐浓度增加，溶液粘度变小，ｎ增大，表明非牛顿流动性减弱，并且进一步讨论了零剪切粘度η_０和外加盐浓度Ｃ_ｓ的依赖关系．     

粘度法研究疏水改性聚丙烯酸与Np7.5的相互作用

研究了氟基团改性和氟碳、碳氢基团同时改性的聚丙烯酸（HM－PAA）以及参与聚合物（PAA）与非离子表面活性剂Np7.5分别在稀溶液和亚浓溶液下的相互作用对特性粘数和Brookfield表观粘度的影响。结果表明,PAA与Np7.5无明显作用,而M－PAA在Np7.5达到一定浓度后,由于Np7.5参与了疏水缔合,特性粘数和表观粘度发生了明显变化。稀溶液中,氟碳基团较多的聚合物出现了链构象的伸展。亚浓溶液中,疏水改性聚合物的粘度都有先上升后下降的变化,但氟碳含量较多的变化更强烈。     

疏水缔合水溶性聚合物AO的溶液粘度行为研究

研究了稀溶液中疏水链链长、无机电解质NaCl和CaCl2对疏水缔合水溶性丙烯酰胺／甲基丙烯酰氨乙基-二甲基烷基溴化铵／丙烯酸钠共聚物(AO)在水溶液中的特性粘数和Huggins常数的影响，以及聚合物AO-8的特性粘数和Huggins常数随温度的变化。结果表明：在稀溶液中，无机电解质离子强度增大，共聚物AO在NaCl和CaCl2溶液中的特性粘数减小，Huggins常数增大。在亚浓溶液范围对聚合物质量分数、温度、剪切速率及NaCl含量对聚合物的水溶液表现粘度的影响进行了研究，观察到疏水缔合聚合物盐水溶液在NaCl含量提高的情况下，出现的增粘现象。     

疏水基改性聚丙烯酰胺的合成及溶液性质

利用自由基胶束聚合法,由丙烯酰胺和甲基丙烯酸十八酯共聚合成了疏水缔合型水溶性聚合物.通过红外光谱表征了共聚物的结构,考察了共聚物浓度、盐浓度、剪切速率以及温度对共聚物溶液性能的影响.试验结果表明,聚合物质量分数大于临界缔合浓度(2%)时,溶液的粘度急剧增大;疏水缔合聚合物溶液的表观粘度随着溶液中NaCl质量分数的增加而增大.     

表面活性剂对纤维素接枝共聚物溶液粘度性质的影响

研究了阴离子十二烷基硫酸钠(SDS)、阳离子十六烷基三甲基溴化铵(CTAB)和非离子聚乙二醇辛基苯基醚(OP)等三种不同类型的表面活性剂对疏水化水溶性两性纤维素接枝共聚物(CGAO)溶液粘度性质的影响.结果表明,在SDS和OP的临界胶束浓度(cmc)附近，CGAO溶液粘度最大，SDS引起CGAO粘度的变化大于OP；即使在CTAB的cmc附近，随着CTAB浓度的增加，CGAO的粘度一直呈下降趋势；非疏水改性的纤维素接枝共聚物的溶液粘度随SDS或CTAB浓度的增加而下降，但几乎不随OP浓度的增大而变化.此外，通过凝胶渗透色谱法测得的保留时间证实了SDS、CTAB和OP与CGAO之间的疏水缔合作用.     

新型疏水缔合聚合物P(AM/POEA)与表面活性剂的相互作用

采用粘度法、荧光探针和透射电镜研究了新型疏水缔合聚合物P(AM/POEA)和表面活性剂SDS和CTAB在水溶液中的相互作用. 聚合物P(AM/POEA)结构中, 疏水体(2-苯氧乙基丙烯酸酯)呈嵌段状无序地分布在聚丙烯酰胺主链上. 这类聚合物很容易和表面活性剂相互作用, 通过疏水缔合, 形成混合胶束状聚集体, 导致溶液粘度剧增. 随聚合物溶液中SDS的加入, 溶液粘度发生大幅度起伏变化, 出现最大值. 粘度最大值对应的表面活性剂浓度c_S,max位于表面活性剂CMC附近, 并发现它的位置不随聚合物微结构而变化. 然而它们缔合作用的增粘程度却与聚合物疏水体含量X_H及疏水嵌段尺寸N_H有关. 在实验浓度范围内, X_H和N_H愈大, 溶液的粘度越高. 此外用透射电镜直接观察到聚合物/表面活性剂体系中聚集体的交联结构形貌.     

氟碳磷脂的合成及其脂质体的生成

合成了两种具有氟碳疏水性链的磷脂, 其极性部分分别为胆碱和磷酸根. 超声分散下, 上述两种磷脂均可形成腈质体, 以电子显微镜观察和动态光散射测定得到胆碱形成的脂质体的尺寸在32-37nm左右. 而对后者的光散射测定得出的尺寸较大并与溶液的pH值有关. 具有胆极性基的氟碳脂质体如同相应的碳氢磷脂一样, 具有包容水溶性受物的能力,但透光性更好. 从荧光探针的荧光强度对温度变化的研究指出, 在53℃左右胆碱型氟碳脂质体发生了相变.     

疏水缔合水溶性聚合物溶液性能研究进展

本文针对疏水缔合水溶性聚合物的稀溶液和半浓溶液两种情况，综述了最近十多年来溶液的性能的研究进展。文中讨论了表征分子量和疏水相互作用的特性粘数与Huggins常数。分别介绍了聚合物浓度、分子量、疏水基类型、含量、长短及序列分布、离子基团的种类和位置、剪切速率、温度以及化学相互作用对溶液性能的影响。     

氰乙基纤维素/二甲基甲酰胺液晶溶液的流变行为

本文通过测定不同浓度的溶液在不同温度和切变速率下的粘度,讨论了氰乙基纤维素/二甲基甲酰胺溶液的流变行为。溶液的流动曲线表明,该溶液是一种假塑性液体。在浓度较高时,存在屈服现象,屈服应力的大小与浓度和温度有关。溶液的浓度—粘度曲线表示出典型的液晶行为。粘度与浓度的关系和屈服应力与浓度的关系相似。溶液的临界浓度随温度的升高而增加。在单相区(各向同性相或液晶相),粘度随温度升高而降低,表观流动活化能大于零。但在两相区,粘度随温度的升高而增大,表观流动活化能小于零。该实验得到的临界浓度与通过光学的方法所得的临界浓度是一致的。     

Effect of Mineral Salts on Steady Rheological Properties of Nonionic Hydrophobically Modified Polyacrylamide and Its Stress-Relaxation Behavior

A micelle-forming polymerizable surfactant monomer, octylphenol polyoxyethylene acrylate (OP-10-AC), was synthesized, and then OP-10-AC was copolymerized with acrylamide (AM) to form nonionic hydrophobically modified polyacrylamide P(AM/OP-10-AC) through micellar copolymerization. In the absence of surfactants, it was investigated in detail that the effect of mineral salts and temperature on steady rheological properties of P(AM/OP-10-AC) solutions and the effect of concentrations on reduced viscosity of P(AM/OP-10-AC) in a dilute solution. The results indicate that concentrations of the copolymer, mineral salts and temperature had a strong influence on shear viscosity of P(AM/OP-10-AC) solutions, and the trend of reduced viscosity of P(AM/OP-10-AC) solutions was distinctly different from polyacrylamide with increasing concentrations of testing solutions. In addition, it was also investigated that stress-relaxation behavior of an aqueous solution of P(AM/OP-10-AC)/KCl. As a result, a stress-relaxation model of the copolymer solutions was proposed, which can further verify the correctness of the conclusion on stress-relaxation behavior of hydrophobic association hydrogels in the paper reported previously.     

A fluorine-containing hydrophobically associating polymer. I. Synthesis and solution properties of copolymers of acrylamide and fluorine-containing acrylates or methacrylates

Fluorine-containing hydrophobically associating polymers have been synthesized by copolymerization of acrylamide with a small amount of an acrylate or methacrylate having a fluorocarbon containing ester group. It was found that hydrophobic associations occurring between these fluorocarbon chains was stronger than the interactions of the corresponding hydrocarbon comonomers and depend on the length of the fluorocarbon chain. The rheological properties of the copolymer solutions were studied. The solutions were found to be highly pseudoplastic but the viscosity loss was completely reversible upon removal of shear. Evidence for hydrophobic association of the fluorocarbon groups was obtained by the dependence of the Brookfield viscosity on temperature, the addition of NaCl, and the addition of organic solvents, urea, and surfactants.     

Supra-molecular association and polymorphic behaviour in systems containing bile acid salts

A wide number of supra-molecular association modes are observed in mixtures containing water and bile salts, BS, (with, eventually, other components). Molecular or micellar solutions transform into hydrated solids, fibres, lyotropic liquid crystals and/or gels by raising the concentration, the temperature, adding electrolytes, surfactants, lipids and proteins. Amorphous or ordered phases may be formed accordingly. The forces responsible for this very rich polymorphism presumably arise from the unusual combination of electrostatic, hydrophobic and hydrogen-bond contributions to the system stability, with subsequent control of the supra-molecular organisation modes. The stabilising effect due to hydrogen bonds does not occur in almost all surfactants or lipids and is peculiar to bile acids and salts. Some supra-molecular organisation modes, supposed to be related to malfunctions and dis-metabolic diseases in vivo, are briefly reported and discussed.     

超临界CO2中丙烯酸含氟酯疏水改性聚丙烯酸的合成

研究了在超临界二氧化碳条件下 ,丙烯酸 1,1 二氢全氟辛酯 (FOA)对聚丙烯酸疏水改性的共聚反应 .发现与通常聚合方法相比含氟丙烯酸酯的产率得到提高 ;反应时间从 2 4h缩短到 4h ;所得产物的后处理也更容易 .同时发现温度对反应有影响 ,含氟酯单体在低温 (T <5 5 0℃ )时活性高于丙烯酸单体 ,在高温 (T >6 0 0℃ )时丙烯酸活性提高较大 .而共聚物水溶液粘度随pH值变化先上升后下降 ,在pH =5 0出现峰值 ,显示其中有分子间缔合存在 .与改性聚丙烯酰胺不同 ,改性聚丙烯酸水溶液粘度随FOA含量的增加而单调上升 ,也证明了分子间缔合的存在     

Rheological behavior of silica suspensions in aqueous solutions of associating polymer

Associating polymers are hydrophilic long-chain molecules containing a small amount of hydrophobic groups. The aqueous solutions show viscoelastic responses above some critical concentrations because a three-dimensional structure is formed by association of hydrophobic groups. When the associating polymers are added to silica suspensions at low concentrations, the flocculation is induced by bridging mechanisms, and the flow of suspensions become shear-thinning. For suspensions prepared with polymer solutions in which the associating network is developed, the viscosity decreases, shows a minimum, and then increases with increasing particle concentration. The viscosity decrease may arise from the breakdown of associating network due to adsorption of polymer chains onto the silica surfaces. As the particle concentration is increased, the polymer concentration in solution is decreased, and finally, all polymer chains are adsorbed on the surfaces. Beyond this point, the partial coverage of particle surfaces takes place and strong interactions are generated between particles by polymer bridging. Since the stable suspensions are converted to highly flocculated systems, the viscosity is increased and the flow becomes shear-thinning. The concentration effect of silica particles on the viscosity behavior of suspensions can be explained by a combination of viscosity decrease in solution due to polymer adsorption and viscosity increase due to flocculation.     

疏水缔合效应对聚丙烯酰胺类水溶液结构和流变性质的影响

以聚合物驱油为背景,研究了部分水解聚丙烯酰胺(HPAM)和缔合型部分水解聚丙烯酰胺(AHPAM)水溶液的结构与流变性质的差别.通过粘度法和静态激光光散射法得到了所分析的聚丙烯酰胺的分子量,用动态激光光散射法和粘度法分析了特定AHPAM分子缔合形态,并用流变学法测定了AHPAM在地层温度与矿化度条件下的线性粘弹性与非线性流变特性.着重讨论了临界缔合浓度的概念,研究了结构和流变性质的关系,以及分析了缔合对聚合物驱油的可能影响.实验结果表明,AHPAM水溶液在宽浓度范围存在分子缔合;一般临界缔合浓度的概念实际反映在进入亚浓溶液范围分子间缔合的效应,剪切速率约为10 s-1时,剪切粘度突降数倍,反映缔合结构在剪切场中的变化,该现象在高缠结浓度下较不明显;拉伸粘度随拉伸速率变化与HPAM定性不同,该拉伸特性反映了疏水缔合近程作用的本质.     

Characterization of thermally sensitive interactions in aqueous mixtures of hydrophobically modified hydroxyethylcellulose and cyclodextrins

Effects of beta-cyclodextrin (beta-CD) or hydroxypropyl-beta-cyclodextrin (HP-beta-CD) addition and temperature on thermodynamic, rheological, and structural features of semidilute solutions of hydroxyethylcellulose (HEC) and its hydrophobically modified analogue (HM-HEC) are reported. Differential scanning calorimetric (DSC) measurements revealed a thermally induced crystal melting transition of beta-CD at high concentrations in solutions of HEC and HM-HEC. No transition with HP-beta-CD was observed in aqueous solution. Viscosity results indicated that at a cosolute concentration of 2 mm, the beta-CD units are threaded onto hydrophobic tails of HM-HEC (C16 groups) to form columnar structures. This arrangement is more effective in the encapsulation of the hydrophobic chains than the monomer hydrophobic deactivation accomplished by the HP-beta-CD units. At cosolute concentrations above 8 mm, no further decoupling of the hydrophobic interactions occurs for any of the cosolutes. Small-angle neutron scattering (SANS) experiments on HM-HEC/beta-CD mixtures suggest that the large-scale association structures in HM-HEC/D(2)O solutions are reduced upon addition of beta-CD, and an interesting temperature effect is observed at 2 mm beta-CD addition. At high beta-CD concentrations and low temperatures, the formation of large beta-CD clusters or crystallites generates cross-links in the HEC and HM-HEC networks, resulting in a viscosity enhancement of several orders of magnitude. This strong temperature effect is not reflected in the structural features probed by SANS.     

Microstructure and association property of hydrophobically modified polyacrylamide of a new family

A new family of hydrophobically modified polyacrylamides was synthesized via copolymerization of acrylamide (AM) and anionic surface-active monomer of acrylamide-type, sodium 2-acrylamido-tetradecane sulfonate (NaAMC₁₄S), in aqueous solution. In the copolymerization, by varying various factors, such as the feed ratio of NaAMC₁₄S to AM and the amount of added electrolyte NaCl and initiator, we prepared copolymers NaAMC₁₄S/AM with different block structures. The relationship between structures and hydrophobic association properties of copolymer chains was studied by using fluorescence probe and viscosimetry. Effects of the content and length of the hydrophobic blocks and the total molecular weight on hydrophobic association of the copolymers in pure water and in brine solution were examined, respectively. The results show that in pure water, hydrophobic association of the copolymers was enhanced as the content and length of the hydrophobic block increase. On the other hands, for a given content and length of the hydrophobic block, the hydrophobic association of the copolymers was enhanced as the total molecular weight increases. For all the copolymers studied, the apparent viscosity of their solutions in pure water has a limited value, but the apparent viscosities of the copolymer brine solutions are much higher than that of their corresponding water solutions, and show strong positive salinity sensitivity. Similarly, the hydrophobic association of the copolymer in brine solutions was enhanced as the content and length of the hydrophobic block increase.     

Temperature dependence of dimerization and dewetting of large-scale hydrophobes: a molecular dynamics study

We studied by molecular dynamics simulations the temperature dependence of hydrophobic association and drying transition of large-scale solutes. Similar to the behavior of small solutes, we found the association process to be characterized by a large negative heat capacity change. The origin of this large change in heat capacity is the high fragility of hydrogen bonds between water molecules at the interface with hydrophobic solutes; an increase in temperature breaks more hydrogen bonds at the interface than in the bulk. With increasing temperature, both entropy and enthalpy changes for association strongly decrease, while the change in free energy weakly varies, exhibiting a small minimum at high temperatures. At around T=Ts=360 K, the change in entropy is zero, a behavior similar to the solvation of small nonpolar solutes. Unexpectedly, we find that at Ts, there is still a substantial orientational ordering of the interfacial water molecules relative to the bulk. Nevertheless, at this point, the change in entropy vanishes due to a compensating contribution of translational entropy. Thus, at Ts, there is rotational order and translational disorder of the interfacial water relative to bulk water. In addition, we studied the temperature dependence of the drying-wetting transition. By calculating the contact angle of water on the hydrophobic surface at different temperatures, we compared the critical distance observed in the simulations with the critical distance predicted by macroscopic theory. Although the deviations of the predicted from the observed values are very small (8-23%), there seems to be an increase in the deviations with an increase in temperature. We suggest that these deviations emerge due to increased fluctuations, characterizing finite systems, as the temperature increases.     

Osmotic and activity coefficients of aqueous bile salt solutions at 25, 37, and 45°C

Osmotic coefficients measured by vapor pressure osmometry are reported for aqueous bile salt solutions at 25, 37, and 45°C. Solute activities decrease rapidly with increasing concentration due to premicellar association and micelle formation. In all cases, activities of the dihydroxy bile salts are lower than those of the trihydroxy bile salts. Osmotic coefficients and activity coefficients increase with increasing temperature. It is suggested that hydrophobic forces contribute substantially to the stability of primary bile salt aggregates and micelles.