焙烧温度对纳米级SO4^2-／TiO2固体超强酸性能的影响

用锐钛型纳米TiO2制备了纳米级SO4^2-／TiO2固体超强酸，考查了焙烧温度对酸强度、比表面积、红外光谱及其催化活性的影响．结果显示该催化剂在450℃焙烧3h，可以形成纳米级SO4^2-／TiO2固体超强酸的结构，用该催化剂催化乙酸和丁醇酯化反应可使酯化率达到98．4％。     

纳米固体酸催化合成无毒增塑剂柠檬酸三辛酯的研究

以柠檬酸和正辛醇为原料,采用自制的纳米固体酸S04^2-／SnO2、SO4^2-／ZrO2、SO4^2-／TiO2及SO4^2-／Fe2O3催化剂合成无毒增塑剂柠檬酸三辛酯（trioctylcitrate,TOC）。分别考察了纳米催化剂种类、催化剂用量、醇／酸物质的量比、反应时间、反应温度等因素对合成TOC反应酯化率的影响,对合成的产品进行红外光谱分析。实验结果表明,自制的固体酸SO4^2-／SnO2催化合成无毒增塑剂柠檬酸三辛酯的最佳反应条件：催化剂用量为1．0g,酸醇比为1：6.3,反应时间1．0h,反应温度190℃。在最佳反应条件下,柠檬酸三辛酯的酯化率可达到98．5％。     

固体超强酸SO42-/TiO2在柠檬酸与正丁醇酯化反应中的催化性能研究

以固体超强酸SO4^2-/TiO2为催化剂合成柠檬酸三丁酯,研究了该催化剂在柠檬酸与正丁醇化反应中的催化活性和稳定性;考察了（MH4）2SO4用量、焙烧温度对催化剂结构、性能的影响;并借助Hammett指示剂法、XRD、AES分析,研究其结构与性能的关系。实验结果表明,在（MH4）2SO4用量为20％、焙烧温度为600℃条件下制得的催化剂,其催化剂选择性99％,锐钛矿TiO2（A）晶相的形成与完善,是提高催化选择性的关键因素;催化剂失活是由于积炭与SO4^2-的流失造成的。     

具有中孔结构的SO4^2—／Zr—HMS型固体超强酸的合成和结构表征

用TEOS－Zr-HAD-H2O-Etheanol体系合成了Zr-HAD的中孔分子筛，脱除模板剂后用0．5mol/L硫酸处理和550℃高温焙烧3h，制得一种中孔SO4^2－／Zr-HAD超强酸催化剂，采用XRD对其结构进行表征，用指示剂法，TG和NH3－TPD对其酸性进行了表征。结果表明，经过一系列处理后制得的SO4^2-／Zr-HAD催化剂具备HMS中孔分子筛的结构特征，其酸强度可达H0＝－13．75，在锆及SO4^2-含量远远低于SO4^2-／ZrO2的条件下，SO4^2-／Zr-HAD催化剂对于苯酐和正丁醇酯化反应的活性仍高于SO4^2-／ZrO2催化剂。     

SO42-促进的中孔含锆分子筛催化合成乙酸松油酯的研究

合成了中孔含锆分子筛Zr-MCM-41，用H2SO4对Zr-MCM-41进行修饰，得到SO4^2-促进的中孔含锆分子筛SO4^2-／Zr-MCM-41．通过XRD、FT—IR表征了其结构．结果表明：Zr—MCM-41和SO4^2-／Zr—MCM-41具有中孔分子筛的特征结构、良好的长程有序性和结晶度；SO4^2-已进入Zr—MCM-41骨架内部，并与骨架原子形成了化学键，从而产生强酸中心，将SO4^2-／Zr—MCM-41用于催化合成乙酸松油酯，考察了催化剂的种类、反应温度、反应时间及反应物配比对松油醇酯化反应结果的影响．     

固体超强酸SO2-4/ZrO2的制备及其催化性能研究

以氧氯化锆为锆原,氨水为沉淀剂,硫酸溶液为浸渍液,通过沉淀-浸渍法制备SO2-4/ZrO2(SZ)酯化催化剂,其结构经BET、X-射线衍射(XRD)、傅立叶变换红外光谱(FT-IR)及扫描电子显微镜(SEM)表征.结果表明:随着焙烧温度升高,催化剂的比表面积依次降低,孔径增大,氧化锆的晶态由无定形态转化为四方晶态再转化为单斜晶态;于600℃焙烧时,催化剂形成的S=O键红外吸收峰最强;于700℃焙烧时,催化剂结构被破坏.在丙烯酸与十八醇的酯化反应中对催化剂进行活性测试.结果表明:600℃焙烧的催化剂产率最高(96.4%).     

SO4^2-/TiO2催化合成乙酸戊酯

以Ti（OBu）4为原料，采用溶胶-凝胶法制备了固体超强酸SO4^2-/TiO2，其结构经XRD，DRS及IR表征。以SO4^2-/TiO2为催化剂，通过乙酸与戊醇反应合成了乙酸戊酯。讨论了影响酯化率的主要因素。实验结果表明，当催化剂用量为0．6g，乙酸87．3mmol，醇酸摩尔比为1．4：1．0，于115℃反应6h时，平行实验的平均酯化率可达94．2％。     

低温陈化超声波共沉淀制备SO4^2-/ZrO2-La2O3催化剂

低温陈化超声波共沉淀法制得SO4^2-/ZrO2-La2O3前驱体,经H2SO4处理,在不同温度下焙烧得到纳米晶催化剂SO4^2-/ZrO2-La2O3;用Hammett指示剂法测定其酸性．用XRD、BET、TEM、IR和XPS对样品进行表征,其催化活性用醋酸和甘油的酯化反应进行了评价．结果表明经超声波搅拌和低温（-15℃）陈化,650℃焙烧4h得到的固体超强酸表现出较高催化活性．     

固体超强酸SO2-4/TiO2负载Tm改性的研究

负载稀土元素Tm以改性SO4^2-/TiO2,制备出固体超强酸催化剂Tm -SO4^2-/TiO2,并用于催化柠檬酸与正丁醇的酯化反应,考察了Tm的负载对催化剂性能的影响,并借助吡啶吸附的程序升温脱附（Py-TPD）法、差热分析（DTA）、热重分析（TGA）、红外光谱（IR）法研究其结构与性能的关系,实验结果表明,Tm的负载,使催化剂的催化活性有所提高,Tm的加量为催化剂量的3%时制得的Tm- SO4^2-/TiO2,其催化酯化反应的转化率为94.4%;Tm的负载能显著降低催化剂表面的积炭量,并且有效抑制So4^2-的流失,使Tm- SO4^2-/TiO2催化剂具有良好的稳定性,重复使用5次后反应的转化仍高达93.1%。     

焙烧温度对纳米级SO2- 4/TiO2固体超强酸性能的影响

用锐钛型纳米TiO2制备了纳米级SO2- 4/TiO2固体超强酸,考查了焙烧温度对酸强度、比表面积、红外光谱及其催化活性的影响.结果显示该催化剂在450℃焙烧3 h,可以形成纳米级SO2-4/TiO2固体超强酸的结构.用该催化剂催化乙酸和丁醇酯化反应可使酯化率达到98.4%.     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.