超声-微波协同萃取分离、气相色谱-质谱联用测定土壤中多环芳烃

建立了常温常压条件下超声-微波协同萃取分离、气相色谱-质谱法（GC-MS）测定土壤样品中微量多环芳烃的方法,结果表明：在土壤含水量和无机盐质量分数分别为10％和6％时,以正已烷-二氯甲烷（1＋1）混合溶液40mL作萃取溶剂,采用100W微波辐射功率（超声振动功率固定为50W）萃取9min,模拟土壤样品中多环芳烃平均回收率可达86．9％,其相对标准偏差为3．6％;通过与索氏抽提、高压密闭微波和开放式微波、直接超声波和间接超声波等萃取方法相比,证明此方法具有样品容量大、萃取时间短、萃取效率高、重现性好等优点。     

超声微波协同萃取-气相色谱法测定土壤中邻苯二甲酸酯类化合物

研究了超声微波协同萃取-气相色谱测定土壤中的邻苯二甲酸酯类化合物。考察了萃取溶剂、微波功率、萃取时间等因素对回收率的影响,得到了最佳萃取条件为:以正己烷/丙酮(1∶1)为萃取剂,溶剂用量为60 mL,微波辐射功率为100 W(超声功率固定为50 W),萃取12 min。该条件下,模拟土样中酞酸酯的平均回收率可达92.5%。方法的检出限为0.05~0.16 mg/kg,相对标准偏差(RSD)5.8%。与直接超声、开放式微波萃取法相比,此法具有明显的优势。方法用于实际土样的测定,所得结果与索氏抽提的结果相当。     

超声协同GC/MS测定土壤中的多环芳烃

本文以土壤中多环芳烃为研究对象,利用超声波产生的机械效应和空化效应,使其从土壤介质表面脱离形成游离状态下的多环芳烃,进入有机溶剂后,形成多环芳烃在土壤介质和有机溶剂之间的动态平衡,进而实现多环芳烃的萃取。通过有机溶剂的筛选和超声萃取优化实验,发现体积比为1∶1的二氯甲烷和正己烷,提取体积为50 mL、超声时间20 min和水浴温度35℃时,对土壤中的多环芳烃的萃取效果最高为82.1～106%。对10.0 g左右的土壤进行低、中、高溶度的加标测试时,16种多环芳烃的加标回收率在85～115%之间,线性回归系数大于0.995,方法检出限在0.001μg·g~(-1)～0.027μg·g~(-1),相对标准偏差在1.98～5.13%之间。这种提取方法实现了绿色低污染、高效准确和低成本的测试要求。     

冷冻去脂-液液分配净化/气相色谱-质谱法测定化妆品中16种多环芳烃

建立了保湿护肤系列化妆品中16种多环芳烃的气相色谱-质谱测定法。对于水剂样品,采用环己烷提取、浓缩等简单前处理;对于膏霜剂样品,采用乙腈+丙酮(8+2,V/V)涡旋提取样品中的待测物,提取液经冷冻去脂、液液萃取净化(氨水-环己烷、水-环己烷),气相色谱-质谱法测定。16种多环芳烃在1～50μg/L均与对应峰面积呈良好线性关系。添加量在1～50μg/kg时,平均回收率(n=6)为78.1%～103.7%,相对标准偏差为2.4%～7.1%,方法检测限为1～10μg/kg。该法可用于化妆品中16种多环芳烃的测定。     

加速溶剂-固相萃取-高效液相色谱法测定土壤及蚯蚓样品中多环芳烃

研究了加速溶剂萃取( ASE)、固相萃取柱净化( SPE)、高效液相色谱( HPLC)联合( ASE-SPE-HPLC)测定土壤及蚯蚓样品中7种多环芳烃(PAHs)的分析方法,确定了以正己烷-丙酮(4∶1, V/V)作为萃取剂,用ASE对土壤及蚯蚓进行萃取,提取液经SPE柱净化(土壤样品用硅胶柱净化,蚯蚓样品用 Al2 O3-硅胶柱净化),正己烷-二氯甲烷(9∶1, V/V)进行洗脱,洗脱体积为10 mL,旋转浓缩蒸干后,乙腈定容,过0.22μm有机滤膜,最后用HPLC对提取液中7种PAHs进行定量的分析方法。土壤样品方法回收率在83.5%~110.2%之间,相对标准偏差为1.0%~4.6%;蚯蚓样品回收率在81.2%~97.1%之间,相对标准偏差为1.6%~4.2%。方法检出限为0.15~0.85μg/kg,且重现性好。可满足样品分析的质量控制要求,表明本分析方法具有良好的准确性与可靠性。     

加速溶剂萃取-气相色谱法测定土壤中16种多环芳烃

利用加速溶剂萃取-气相色谱法测定土壤中16种多环芳烃的分析。研究了萃取时间、温度、压力、样品的粒度对萃取效率的影响及不同淋洗液在硅胶柱净化过程中对方法回收率的影响。实验结果表明,加速溶剂萃取方法对16种多环芳烃的萃取溶剂量小,萃取时间短萃取回收率分别在74%~95%之间;对标准样品的检出限为0.00004~0.02 mg/kg;方法RSD为4%~15%。用此方法测定了株洲土壤中的多环芳烃含量。     

超声微波协同萃取/气相色谱法测定土壤中的多溴联苯醚

建立了同时测定土壤中7种多溴联苯醚(PBDEs)的超声微波协同萃取/气相色谱测定方法.考察了萃取溶剂的种类和用量、微波功率、萃取时间等因素对模拟土壤中PBDEs回收率的影响,得到了最佳萃取条件:萃取剂为50 mL正己烷-丙酮(1:1),微波辐射功率为90W,萃取时间为10 min.在最佳条件下,PB-DEs在10～40...     

微波辅助萃取-气相色谱测定土壤中多氯联苯

建立了微波辅助萃取-气相色谱-微电子捕获检测土壤样品中6种多氯联苯(pcb28, pcb52, pcb101, pcb138, pcb153和pcb180)的方法. 确定了以V(20 mL丙酮):V(正己烷)＝1:1混合溶剂作萃取剂, 萃取温度110 ℃, 仪器功率800 W, 微波萃取5 min的样品前处理条件, 并用柱温程序优化了GC-μECD分析条件. 方法的检出限为0.027～0.087 ng/g; 相对标准偏差为3.4%～7.6% (n=6); 加标平均回收率79.8%～91.1%. 可用于土壤环境中多氯联苯的监测分析.     

三甲基杯[6]芳烃固相微萃取-气相色谱法测定土壤中的多环芳烃

采用溶胶-凝胶方法制备了三甲基杯[6]芳烃/羟基硅油(C[6]/OH-TSO)固相微萃取(SPME)探头,通过与气相色谱-氢火焰(GC-FID)联用测定了土壤中的多环芳烃(PAHs)。考察了影响萃取效率的因素如时间、温度和盐浓度等,比较了杯[6]芳烃探头和杯[4]芳烃探头以及商用PDMS探头对PAHs的萃取效果。结果表明:杯[6]芳烃SPME探头具有耐高温(380℃)、使用寿命长(7200次)等特点,对样品中PAHs的萃取效果明显优于其它探头。本方法检出限低(0.008~0.440mg/L),重现性好(RSD<7%),线性范围宽(3个数量级)。回收率在70.20%~105.1%之间。     

气相色谱-串联质谱法测定土壤中多环芳烃和多氯联苯

研究土壤中持久性有机污染物的含量可以为区域环境治理和来源解析提供基础数据。本文通过固相萃取结合气相色谱-串联质谱法建立了16种多环芳烃和15种多氯联苯的检测方法,并优化了固相萃取净化方法、色谱条件以及质谱碰撞能量。结果表明16种多环芳烃和15种多氯联苯的标准曲线线性关系良好,方法线性相关系数r~20.999,方法的检出限为0.1~2.5μg·kg~(-1),16种多环芳烃的平均加标回收率范围为62.5%~113.5%,相对标准偏差在2.3%~8.2%之间,15种多氯联苯的平均加标回收率范围为62.6%~91.4%,相对标准偏差在5.2%~7.8%之间。方法的准确度和精密度较高,通过对实际样品的测定,说明该方法具有较低的检出限及较强的抗干扰能力,能满足土壤中多环芳烃和多氯联苯的检测要求。     

Determination of polycyclic aromatic hydrocarbons in aqueous samples by microwave assisted headspace solid-phase microextraction and gas chromatography/flame ionization detection

The novel pretreatment technique, microwave-assisted heating coupled to headspace solid-phase microextraction (MA-HS-SPME) has been studied for one-step in situ sample preparation for polycyclic aromatic hydrocarbons (PAHs) in aqueous samples before gas chromatography/flame ionization detection (GC/FID). The PAHs evaporated into headspace with the water by microwave irradiation, and absorbed directly on a SPME fiber in the headspace. After being desorbed from the SPME fiber in the GC injection port, PAHs were analyzed by GC/FID. Parameters affecting extraction efficiency, such as SPME fiber coating, adsorption temperature, microwave power and irradiation time, and desorption conditions were investigated.Experimental results indicated that extraction of 20 mL aqueous sample containing PAHs at optional pH, by microwave irradiation with effective power 145 W for 30 min (the same as the extraction time), and collection with a 65 μm PDMS/DVB fiber at 20 °C circular cooling water to control sampling temperature, resulted in the best extraction efficiency. Optimum desorption of PAHs from the SPME fiber in the GC hot injection port was achieved at 290 °C for 5 min. The method was developed using spiked water sample such as field water with a range of 0.1-200 μg/L PAHs. Detection limits varied from 0.03 to 1.0 μg/L for different PAHs based on S/N = 3 and the relative standard deviations for repeatability were <13%. A real sample was collected from the scrubber water of an incineration system. PAHs of two to three rings were measured with concentrations varied from 0.35 to 7.53 μg/L. Recovery was more than 88% and R.S.D. was less than 17%. The proposed method is a simple, rapid, and organic solvent-free procedure for determination of PAHs in wastewater.     

Monitoring of PAHs in air by collection on XAD-2 adsorbent then microwave-assisted thermal desorption coupled with headspace solid-phase microextraction and gas chromatography with mass spectrometric detection

Microwave-assisted thermal desorption (MAD) coupled to headspace solid-phase microextraction (HS-SPME) has been studied for in-situ, one-step, sample preparation for PAHs collected on XAD-2 adsorbent, before gas chromatography with mass spectrometric detection. The PAHs on XAD-2 were desorbed into the extraction solution, evaporated into the headspace by use of microwave irradiation, and absorbed directly on a solid-phase microextraction fiber in the headspace. After desorption from the SPME fiber in the hot GC injection port, PAHs were analyzed by GC–MS. Conditions affecting extraction efficiency, for example extraction solution, addition of salt, stirring speed, SPME fiber coating, sampling temperature, microwave power and irradiation time, and desorption conditions were investigated. Experimental results indicated that extraction of 275 mg XAD-2, containing 10–200 ng PAHs, with 10-mL ethylene glycol–1 mol L⁻¹ NaCl solution, 7:3, by irradiation with 120 W for 40 min (the same as the extraction time), and collection with a PDMS–DVB fiber at 35 °C, resulted in the best extraction efficiency. Recovery was more than 80% and RSD was less than 14%. Optimum desorption was achieved by heating at 290 °C for 5 min. Detection limits varied from 0.02 to 1.0 ng for different PAHs. A real sample was obtained by using XAD-2 to collect smoke from indoor burning of joss sticks. The amounts of PAHs measured varied from 0.795 to 2.53 ng. The method is a simple and rapid procedure for determination of PAHs on XAD-2 absorbent, and is free from toxic organic solvents.     

微波提取-高效液相色谱法测定大气颗粒物中的多环芳烃

建立了一种微波提取-高效液相色谱法测定大气颗粒物中多环芳烃的方法。吸附有颗粒物的超细玻璃纤维/石英纤维滤膜用正己烷/丙酮(1∶1,v/v)混合溶剂经微波提取,提取液用弗罗里硅土柱净化,经浓缩定容后,采用液相色谱法-二极管阵列(PDA)-荧光双检测器测定。目标化合物在20.0~500μg/L范围内线性良好,相关系数不小于0.996 0。空白膜加标结果显示,目标化合物的回收率在56.3%~101%之间。该法已运用于南京市大气颗粒物中多环芳烃分布的调查研究。     

Determination of polycyclic aromatic hydrocarbons in marine sediments using a new ASE-SFE extraction technique

In order to determine PAHs in marine sediment samples by GC/MS(SIM) a new extraction approach of ASE-SFE was evaluated using combined accelerated solvent extraction (ASE, dynamic and static mode) and supercritical fluid extraction (SFE, dynamic mode) without further purification of the sample. The solvents used for ASE-SFE were methylene chloride and carbon dioxide. The recovery data, precision and accuracy of the whole method were evaluated statistically. The average recoveries of PAHs, based on deuterated internal standards were 77% for 2-3-ring PAHs, 85% for 4-ring PAHs, 88% for 5-ring PAHs and 97% for 6-ring PAHs. The extraction time required for the ASE-SFE technique was 30 min, which is longer than in the case of independent use of ASE and shorter compared to SFE. ASE-SFE recoveries of PAHs from SRM marine sediment are comparable for (2-3-ring, 4-ring PAHs) or higher (5-ring, 6-ring PAHs) than reported for the conventional extraction methods of ASE and SFE. Method detection limits of (MDL) were statistically estimated. MDL values obtained for 15 PAHs compounds vary between 0.06 ngg(-1) and 3.54 ngg(-1).     

Determination of polycyclic aromatic hydrocarbons in marine sediments using a new ASE-SFE extraction technique

In order to determine PAHs in marine sediment samples by GC/MS(SIM) a new extraction approach of ASE-SFE was evaluated using combined accelerated solvent extraction (ASE, dynamic and static mode) and supercritical fluid extraction (SFE, dynamic mode) without further purification of the sample. The solvents used for ASE-SFE were methylene chloride and carbon dioxide. The recovery data, precision and accuracy of the whole method were evaluated statistically. The average recoveries of PAHs, based on deuterated internal standards were 77% for 2–3-ring PAHs, 85% for 4-ring PAHs, 88% for ¶5-ring PAHs and 97% for 6-ring PAHs. The extraction time required for the ASE-SFE technique was 30 min, which is longer than in the case of independent use of ASE and shorter compared to SFE. ASE-SFE recoveries of PAHs from SRM marine sediment are comparable for (2–3-ring, 4-ring PAHs) or higher (5-ring, 6-ring PAHs) than reported for the conventional extraction methods of ASE and SFE. Method detection limits of (MDL) were statistically estimated. MDL values obtained for 15 PAHs compounds vary between 0.06 ngg^?1 and 3.54 ngg^?1.     

Multiwalled carbon nanotubes as adsorbents of solid-phase extraction for determination of polycyclic aromatic hydrocarbons in environmental waters coupled with high-performance liquid chromatography

Multiwalled carbon nanotubes (MWCNTs) were used as a novel kind of solid-phase extraction adsorbents in this work as well as an analytical method based on MWCNTs solid-phase extraction (SPE) combined with high-performance liquid chromatography (HPLC) was established for the determination of polycyclic aromatic hydrocarbons (PAHs), some of which belong to typical persistent organic pollutants (POPs) owing to their carcinogenicity and endocrine disrupting activity. Several conditions that probably affected the extraction efficiency including the eluent volume, sample flow rate, sample pH and the sample volume were optimized in detail. The characteristic data of analytical performance were determined to investigate the sensitivity and precision of the method, and the method was applied to the determination of PAHs in environmental water samples such as river water sample, tap water sample and wastewater sample from the constructed wetland effluent. The experimental results indicated that there were excellent linear relationship between peak area and the concentration of PAHs over the range of 0.04-100 microg L(-1), and the precisions (RSD) were 1.7-4.8% under the optimal conditions. The detection limits of proposed method for the studied PAHs were 0.005-0.058 microg L(-1) (S/N=3). The recoveries of PAHs spiked in environmental water samples ranged from 78.7 to 118.1%. It was concluded that MWCNTs packed cartridge coupled with HPLC was an excellent alternative for the routine analysis of PAHs at trace level.     

微波萃取土壤中PAHs的研究

研究了MK-1型光纤压力自控微波溶样系统用于微波萃取的可行性.以合成土样为对象,比较系统地研究了微波萃取PAHs的条件、萃取效率以及溶剂、水分、土壤基体物质等因素的影响.在微波作用下丙酮-正已烷(体积比为1:1)和二氯甲烷对PAHs的萃取能力相近;试样中小于20%的水分使丙酮-正己烷(体积比为1:1)的萃取能力提高,而水分高于5%则使二氯甲烷的萃取能力略有降低.在选定条件下,萘、苊烯、芴、菲、蒽、(出)、苯并(a)芘的回收率在82.2%～94.1%之间.     

Determination of polycyclic aromatic hydrocarbons in marine sediments by high-performance liquid chromatography after microwave-assisted extraction with micellar media

A simple and rapid method is developed for extraction and determination of polycyclic aromatic hydrocarbons (PAHs) in marine sediments. The procedure was based on the microwave-assisted extraction of PAHs in marine sediment samples using a micellar medium of Polyoxyethylene 10 lauryl ether as extractant. Two-level factorial designs have been used to optimize the microwave extraction process. The analysis of extracts has been carried out by HPLC with UV detection. Fortified sediments gave an average recovery between 85.70 and 100.73%, with a relative standard deviation of 1.77-7.0% for PAHs with a ring number higher than three.     

Simultaneous microwave-assisted extraction of polycyclic aromatic hydrocarbons, polychlorinated biphenyls, phthalate esters and nonylphenols in sediments

A new method was developed for the simultaneous extraction of polycyclic aromatic hydrocarbons (PAHs), polychlorinated biphenyls (PCBs), phthalate esters (PEs), nonylphenols (NPs) and nonylphenol mono- and diethoxylates (NP1EOs and NP2EOs, respectively) in sediment samples by means of a closed microwave system. The extractions were carried out at 21 psi and 80% of microwave power and 15 ml of acetone were used as the common extraction solvent. The filtered extract was further fractionated in two groups using Florisil cartridges: PAHs and PCBs were eluted with n-hexane:toluene (4:1) and the PEs, NPs and ethoxylates were eluted with ethyl acetate. All the compounds were analysed by gas chromatography-mass spectrometry (GC-MS). In case of PAHs and PCBs, the developed method was validated by comparison of the results obtained for the certified reference material NIST 1944 with the certified values. In the absence of a reference material for phthalate esters and nonylphenols, one sediment sample was extracted twice under the optimal conditions in order to check than an exhaustive extraction of the analytes occurred. This method is currently used in the study of the distribution of those organic contaminants in the estuaries of the Bay of Biscay (Spain).     

Factors Controlling Leaching of Polycyclic Aromatic Hydrocarbons from Petroleum Source Rock Using Nonionic Surfactant

The extraction of polycyclic aromatic hydrocarbons (PAHs) from petroleum source rock by nonionic surfactants with the assistance of microwave irradiation was investigated and the conditions for maximum yield were determined. The results showed that the extraction temperatures and type of surfactant have significant effects on extraction yields of PAHs. Factors such as surfactant concentration, irradiation power, sample/solvent ratio and mixing surfactants (i.e., mixture of surfactant at specific ratio) also influence the extraction efficiencies for these compounds. The optimum temperature for microwave-assisted nonionic surfactant extraction of PAHs from petroleum source rock was 120 °C and the best suited surfactant was Brij 35. The new method showed extraction efficiencies comparable to those afforded by the Soxhlet extraction method, but a reduction of the extraction times and environmentally friendliness of the new nonionic surfactant extraction system are clear advantages. The results also show that microwave-assisted nonionic surfactant extraction is a good and efficient green analytical preparatory technique for geochemical evaluation of petroleum source rock.