木粉/聚乙烯复合材料的等离子体表面处理——等离子体处理时间对复合材料表面特性的影响

为改善木粉/聚乙烯复合材料的表面粘接性,实现木粉/聚乙烯复合材料的无缝连接,利用低温等离子体处理技术,对木粉/聚乙烯复合材料进行了表面处理.采用接触角测试、傅立叶变换红外光谱分析(FTIR)以及X射线光电子能谱分析(XPS)研究了等离子体处理前后复合材料表面性能的变化.试验结果表明,经等离子体处理后,复合材料表面的接触角减小,表面润湿性得以改善;FTIR分析结果表明,经等离子体处理后,复合材料表面有—OH、—C=O和—O—C=O基团生成;XPS分析表明,经等离子体处理后,复合材料表面含氧基团的含量增加,在较短的时间内表面氧元素含量增加会达到平衡,且生成大量的—O—C=O基团。     

空气介质阻挡放电对超高分子量聚乙烯纤维表面性能及粘结力的影响研究

利用空气介质阻挡放电(DBD)等离子体对超高分子量聚乙烯(UHMWPE)纤维进行表面改性处理研究以提高纤维表面的润湿和粘结性能.分别研究了等离子体处理时间及电压对UHMWPE纤维拉伸断裂强力、接触角、表面形貌、表面化学成分和粘结性能等的影响规律.SEM分析结果表明,空气DBD等离子体处理后UHMWPE纤维表面出现垂直于纤维轴向分布的凹坑和裂纹,使得纤维表面粗糙度显著增加.XPS分析表明空气DBD处理后纤维表面碳元素含量显著下降;同时氧元素和氮元素的含量均较处理前增加,但氧元素含量增加的幅度显著高于氮元素.XPS分峰结果表明等离子体处理后UHMWPE纤维纤维表面C—O/C—N基团含量显著增加,同时出现了C O和O—C O这2种新的含氧官能团.同时,接触角及和与环氧树脂之间的界面剪切力(IFSS)测试结果表明DBD等离子体处理后UHMWPE纤维表面润湿性能和粘结力均产生显著提高,且随着等离子体处理时间或电压的增加,UHMWPE纤维的表面润湿性能和粘结力均呈现先上升后下降的趋势.空气DBD等离子体处理对UHMWPE纤维的力学性能影响较小,当处理电压低于200 V,处理时间小于100 s,纤维强力下降比率小于5.2%.     

等离子体改性的聚偏氟乙烯表面结构的XPS研究

采用5种气氛等离子体处理聚偏氟乙烯(PVF_2)基片,用XPS研究了PVF_2表面结构的变化。结果表明,处理后的PVF_2基片表面嵌入了C—O,C—NH_2,—CHF和COOH基团,因而改变了表面性质。     

等离子体改性聚丙烯纤维表面的XPS研究

用等离子体技术处理了聚丙烯纤维表面．用Ｘ－射线光电子能谱（ＸＰＳ）研究了聚合物表面的元素组成、相对含量的变化、表面官能团的类型．采用曲线拟合分峰技术对谱图进行数学处理，结果表明：尽管处理气氛不同，聚丙烯纤维表面除含有Ｃ—Ｈ和Ｃ＝Ｃ键外，还引入了Ｏ、Ｎ元素．形成活性基团：－ＯＨ、＞Ｃ＝Ｏ、－ＣＯＯＨ、－ＮＨ２和－ＣＯＮＨ２等，提高了聚合物表面活性。     

甲基丙烯醛与H_4PMo_(11)V_1/SiO_2催化剂相互作用的红外光谱研究

本文报告了甲基丙烯醛(MAL)在杂多酸催化剂H_4PMo_(11)V_1/SiO_3上吸附的红外光谱研究结果。在表面上生成了三种表面络合物,CH_2=C(CH_3)—CHO(Ⅰ)、CH_2=C(CH_3)—CO(Ⅱ)和。认为它们是生成甲基丙烯酸(MAA)的中间物。发现在较高温度(300℃)抽空处理的催化剂上不发生MAL的化学吸附,同时表征杂多酸阴离子结构的υ(P—O)和一个υ(Me—O—Me,Me代表Mo或V)谱带也消失了。     

以Au/Cu纳米棒为基底的肺腺癌组织的特征表面增强拉曼光谱研究

通过金铜共混法制备了Au/Cu合金纳米棒,研究了铜掺杂对金纳米棒等离子体共振吸收和结构的影响,探究了Au/Cu合金纳米棒的等离子体共振拉曼增强效应.以Au/Cu合金纳米棒为基底对肺腺癌组织和癌旁正常组织进行了表面增强拉曼光谱检测.结果显示,癌变组织具有比癌旁正常组织更强的拉曼信号峰,位于1250,1344,1408,1568,1608和2560 cm~(-1)附近的拉曼峰分别与蛋白质的AmideⅡ氨基化合物、C—H弯曲振动、核酸中CH_3的对称变角振动、蛋白质色氨酸惰性环振动、蛋白质酰胺I谱带分子间反平行β-折叠的C—O健伸缩振动和蛋白质的巯基(S—H)伸缩振动有关,2936 cm~(-1)附近的拉曼峰为蛋白质CH_2的对称伸缩振动和CH_3的反对称伸缩振动共同作用产生.以铜掺杂的金纳米棒为基底的表面增强拉曼光谱法有望成为检测肺癌组织的有效手段.     

XPS研究低温等离子体聚苯乙烯表面改性

用氮气、二氧化碳和空气等离子体技术处理聚苯乙烯表面 ,并用X光电子能谱 (XPS)测定了聚合物表面的元素组成 ,相对含量和表面功能团的类型 .结果表明 ,经过不同条件处理后的聚合物表面引入了含氮和含氧基团 ,这对改善材料的沾润性和粘着性将起着明显作用 ;另外 ,不同处理条件对PS表面的氮、氧含量有很大影响     

氢终止金刚石表面的形成机理

为考察金刚石形成氢终止表面的反应机制,采用微波氢等离子体处理以及电阻丝氢气气氛加热处理进行对比研究.利用光发射谱(OES)和漫反射傅里叶变换红外光谱(DRIFTS)分别表征了微波氢等离子体中的活性基团和金刚石表面氢终止浓度.结果表明,微波氢等离子体环境下,随着衬底温度、等离子体密度和能量的增加,温度至700 ℃ (800 W/3 kPa)时,等离子体中出现了明显的CH基团;相应地,金刚石表面氢终止浓度随温度、等离子体密度和能量的增加而增加.采用氢气气氛下电阻丝加热的方法同样形成了氢终止金刚石表面,表明微波等离子体处理金刚石表面形成氢终止主要源于由温度控制的表面化学反应,而非等离子体的物理刻蚀作用.氧终止金刚石表面形成氢终止的机制是表面C=O键在高于500 ℃时分解为CO,相应的悬挂键由氢原子或氢分子占据.     

等离子体处理云母粉对其表面特性及对其与聚合物界面特性的影响

采用等离子体方法处理填料及增强体表面,是提高填料及增强体与聚合物基体的粘合性、改善复合材料性能的一个新的有效途径。目前研究工作集中于处理条件与复合体系宏观性能的关系上,对处理前后填料表面性质以及填料与聚合物界而性质变化的探讨却很少。而只有了解上述变化才能从本质上认识处理条件与复合体系宏观性能的关系。本文首次对云母粉进行丁醛等离子体处理,测定了处理前后液体在云母粉表面的接触角,估算了处理条件     

聚四氟乙烯表面的等离子体处理

聚烯烃类聚合物粘结与印染性能均较差,以往都是用氧化剂法改善其表面性能,近年来采用等离子体表面处理的方法,不仅能改变表面的润湿性,而且无污染、效率高,完全有可能取代传统的表面处理方法。 本文报道我们在自制的装置上,用空气等离子体,对     

Wettability of a polytetrafluoroethylene surface by an aqueous solution of two nonionic surfactant mixtures

Measurements of the advancing contact angle (theta) were carried out for an aqueous solution of p-(1,1,3,3-tetramethylbutyl)phenoxypoly(ethylene glycol)s (Triton X-100 (TX100) and Triton X-165 (TX165) mixtures) on polytetrafluoroethylene (PTFE). The obtained results indicate that the wettability of PTFE depends on the concentration and composition of the surfactant mixture. The minimum of the dependence between the contact angle and composition of the mixtures for PTFE for each concentration at a monomer mole fraction of TX100, alpha = 0.8, points to synergism in the wettability of PTFE. This effect was confirmed by the negative values of interaction parameters calculated on the basis of the contact angle and by the Rosen approach. In contrast to Zisman, there was no linear dependence between cos theta and the surface tension of an aqueous solution of TX100 and TX165 mixtures for all studied systems, but a linear dependence existed between the adhesional tension and surface tension for PTFE over the whole concentration range, the slope of which was -1, indicating that the surface excess of the surfactant concentration at the PTFE-solution interface was the same as that at the solution-air interface for a given bulk concentration. Similar values of monomer mole fractions of the surfactants at water-air and PTFE-water interfaces calculated on the basis of the surface tension and contact angles showed that adsorption at these two interfaces was the same. It was also found that the work of adhesion of an aqueous solution of surfactants to the PTFE surface did not depend on the type of surfactant and its concentration. This means that for the studied systems the interaction across the PTFE-solution interface was constant and was largely of Lifshitz-van der Waals type. On the basis of the surface tension of PTFE, the Young equation, and the thermodynamic analysis of the adhesion work of an aqueous solution of surfactant to the polymer surface, it was found that in the case of PTFE the changes in the contact angle as a function of the mixture concentration of two nonionic surfactants resulted only from changes in the polar component of the solution surface tension.     

Trimethyl borate‐treated polytetrafluoroethylene micropowders with improved hydrophilic and adhesive properties based on coordination bond theory

Based on coordination bond theory, the current study proposes a novel method to modify the surface of the polytetrafluoroethylene (PTFE) micropowders. The samples were treated with trimethyl borate in the n‐hexane solution, and this improves the hydrophilic and adhesive properties of PTFE micropowders. The surface properties of treated samples were evaluated by using X‐ray photoelectron spectrometry, contact angle measurement, settling velocity measurement, and adhesive property measurement. Trimethyl borate treatment led to an evident increase in the hydrophilic and adhesive properties of PTFE micropowders. The water contact angle of PTFE micropowders decreased from 115° to 85.4°, while the ethanol contact angle of PTFE micropowders decreased from 39.8° to 11.2° owing to the combination of the trimethyl borate with PTFE micropowders as indicated by the X‐ray photoelectron spectrometry spectra. Furthermore, the settling velocity of powders dispersed in ethanol/water (1/10) solution (pH = 8.5) improved (with a settlement ratio exceeding 20% in 60 minutes), and the fracture stress of the powders/resin composite membrane increased from 4.68 to 6.67 MPa while the elongation at the yield of membrane increased from 25.4% to 31.5%.     

The wettability of polytetrafluoroethylene by aqueous solution of cetyltrimethylammonium bromide and Triton X-100 mixtures

Measurements of the advancing contact angle (theta) were carried out for aqueous solution of cetyltrimethylammonium bromide (CTAB) and p-(1,1,3,3-tetramethylbutyl) phenoxypoly(ethylene glycol), Triton X-100 (TX100) mixtures on polytetrafluoroethylene (PTFE). The obtained results indicate that the wettability of PTFE depends on the concentration and composition of the surfactants mixture. There is a minimum of the dependence between contact angle and composition of the mixtures for PTFE for each concentration at a monomer mole fraction of CTAB, alpha, equal 0.2, which points to the synergism in the wettability of PTFE. In contrast to Zisman, there is no linear dependence between costheta and the surface tension of aqueous solution of CTAB and TX100 mixtures for all studied systems, but a linear dependence exists between the adhesional tension and surface tension for PTFE in the whole concentration range, the slope of which is -1, that suggests that the surface excess of the surfactant concentration at the PTFE-solution interface is the same as that at the solution-air interface for a given bulk concentration. It was also found that the work of adhesion of aqueous solution of surfactants to PTFE surface did not depend on the type of surfactant and its concentration. It means that the interactions across PTFE-solution interface were constant for the systems studied, and they were largely Lifshitz-van de Waals type. On the basis of the surface tension of PTFE and the Young equation and thermodynamic analysis of the adhesion work of aqueous solution of surfactant to the polymer surface it was found that in the case of PTFE the changes of the contact angle as a function of the mixture of nonionic and cationic surfactants concentration resulted only from changes of the polar component of solution surface tension.     

苄基取代甜菜碱对聚四氟乙烯表面润湿性的影响

利用座滴法研究了两性离子表面活性剂苄基取代烷基羧基甜菜碱(BCB)和苄基取代烷基磺基甜菜碱(BSB)在聚四氟乙烯(PTFE)表面上的润湿性质,考察了表面活性剂浓度对接触角的影响趋势,并讨论了粘附张力、固-液界面张力和粘附功的变化规律.研究发现,在低浓度时,表面活性剂通过疏水作用吸附到PTFE表面,疏水链苄基取代支链化使其在固-液界面上的吸附明显低于气-液界面,接触角在很大的范围内保持不变.当体相浓度增加到大于临界胶束浓度(cmc)时, BCB和BSB分子在固-液界面上继续吸附,分子逐渐直立,造成PTFE-液体之间的界面张力(γ_SL)进一步降低,表面亲水性增加,接触角随浓度增加明显降低;另一方面, BSB由于具有较大的极性头,在高浓度时空间阻碍作用明显,导致其对PTFE表面润湿性改变程度小于BCB.     

Evidence of the synergetic role of charged species and atomic oxygen in the molecular etching of PTFE surfaces for hydrophobic surface synthesis

The transformation of a poly(tetrafluoroethylene) (PTFE) hydrophobic surface into a superhydrophobic one using a low pressure RF plasma is explored using optical emission spectrometry (OES), X-ray photoelectron spectroscopy (XPS), water contact angle (WCA) measurements, mass measurements, and atomic force microscopy (AFM). It is shown that the increase in contact angle is due to an increase of roughness provoked by a chemical etching of the surface. We propose a molecular mechanism for etching that requires the simultaneous presence of atomic oxygen and negatively charged species (electrons) at the PTFE surface.     

Wettability of polymeric solids by ternary mixtures composed of hydrocarbon and fluorocarbon nonionic surfactants

Contact angle (θ) measurements on poly(tetrafluoroethylene) (PTFE) and polymethyl methacrylate (PMMA) surface were carried out for the systems containing ternary mixtures of surfactants composed of: p-(1,1,3,3-tetramethylbutyl)phenoxypoly(ethylene glycols), Triton X-100 (TX100), Triton X-165 (TX165) and Triton X-114 (TX114), and fluorocarbon surfactants, Zonyl FSN100 (FSN100) and Zonyl FSO100 (FSO100). The aqueous solutions of ternary surfactant mixtures were prepared by adding TX114, FSN100 or FSO100 to binary mixtures of TX100+TX165, where the synergistic effect in the reduction of the surface tension of water (γ(LV)) was determined. From the obtained contact angle values, the relationships between cosθ, the adhesion tension and surface tension of solutions, cosθ and the reciprocal of the surface tension were determined. On the basis of these relationships, the correlation between the critical surface tension of PTFE and PMMA wetting and the surface tension of these polymers as well as the work of adhesion of aqueous solutions of ternary surfactant mixtures to PTFE and PMMA surface were discussed. The critical surface tension of PTFE and PMMA wetting, γ(C), determined from the contact angle measurements of aqueous solutions of surfactants including FSN100 or FSO100 was also discussed in the light of the surface tension changes of PTFE and PMMA under the influence of film formation by fluorocarbon surfactants on the surface of these polymers. The γ(C) values of the studied polymeric solids were found to be different for the mixtures composed of hydrocarbon surfactants in comparison with those of hydrocarbon and fluorocarbon surfactants. In the solutions containing fluorocarbon surfactants, the γ(C) values were different taking into account the contact angle in the range of FSN100 and FSO100 concentration corresponding to their unsaturated monolayer at water-air interface or to that saturated.     

Electrochemical characteristics and interfacial contact resistance of Ni-P/TiN/PTFE coatings on Ti bipolar plates

The Ni-P/TiN/PTFE (poly tetra fluoroethylene) composite coatings were prepared by electroless plating method on Ti plate, which was used as bipolar plates of proton exchange membrane fuel cells (PEMFCs). The morphology, crystallographic texture, electrochemical corrosion, contact resistance, and hydrophobic property of the Ti bipolar plates with coatings were investigated. The results revealed that Ni-P/TiN/PTFE coating had a dense surface morphology, uniform distribution of composite particles. Ti with coating showed 0.48 μA cm² of corrosion current in the simulated solution of PEMFCs and 6 mΩ cm² of interfacial contact resistance (ICR). The hydrophobicity test showed that the coating interface was flat and the wetting angle was 112.4°. In conclusion, The Ni-P/TiN/PTFE composite coatings exhibit superior improvement in corrosion resistance, interface hydrophobicity, and conductivity to Ni-P, Ni-P/TiN, and Ni-P/PTFE coatings. The Ni-P/TiN/PTFE coating was suited for bipolar plate surface modification of bipolar plates.     

丙烯酸水溶液聚合法制备PTFE/PAA/Nafion膜及其性能

采用廉价的多孔聚四氟乙烯(PTFE)膜作为基底, 用少量的Nafion与PTFE膜复合可制备低成本的质子膜. 但疏水性的PTFE膜与亲水性的Nafion膜结合性不佳. 基于此, 本文对疏水性的PTFE膜材料表面进行设计, 先采用丙烯酸对疏水性的PTFE膜表面进行亲水性改性, 再喷涂亲水性Nafion膜, 完成低成本PTFE/PAA/Nafion膜的制备. 实验结果表明, 改性前的PTFE膜材料水接触角为150°, 改性后的膜接触角变为55.6°, 亲水性大幅上升, 膜的机械强度和尺寸稳定性(断裂强度为25.2 MPa, 80 ℃下的溶胀率为11.9%)均优于Nafion117膜, 而 Nafion用量则节省了60%. PTFE/PAA/Nafion膜具有高质子导通率(80 ℃下达到131.9 mS/cm), 接近于Nafion117膜, 最大功率密度可以达到404.2 mW/cm².     

支链化阳离子和甜菜碱表面活性剂对聚四氟乙烯表面润湿性的影响

利用座滴法研究了支链化阳离子表面活性剂十六烷基羟丙基氯化铵(C₁₆GPC)和两性离子表面活性剂十六烷基羧酸甜菜碱(C₁₆GPB)在聚四氟乙烯(PTFE)表面上的吸附机制和润湿性质, 考察了表面活性剂浓度对表面张力、接触角、粘附张力、固液界面张力和粘附功的影响趋势. 研究发现, 低浓度条件下, 表面活性剂疏水支链的多个亚甲基基团与PTFE表面发生相互作用, 分子以平躺的方式吸附到固体界面; 支链化表面活性剂形成胶束的阻碍较大, 浓度大于临界胶束浓度(cmc)时, C₁₆GPC和C₁₆GPB分子在固液界面上继续吸附, 与PTFE作用的亚甲基基团减少, 分子逐渐直立, 固液界面自由能(γ_sl)明显降低. 对于支链化的阳离子和甜菜碱分子, 接触角均在浓度高于cmc后大幅度降低.     

超疏水聚苯胺/聚四氟乙烯复合膜的制备及油-水乳液分离性能

以苯胺为原料, 采用原位聚合法在聚四氟乙烯(PTFE)基体上合成聚苯胺/聚四氟乙烯(PANI/PTFE)复合膜. 利用光学显微镜、 扫描电子显微镜(SEM)、 傅里叶变换红外光谱(FTIR)、 紫外-可见吸收光谱(UV-Vis)和静态水接触角测试对PANI/PTFE复合膜的形貌、 结构和浸润性进行分析, 并对其油包水乳液分离性能、 通量和循环使用性能进行了测试. 研究结果表明, PANI/PTFE复合膜仅在重力条件就能有效分离油包水乳液; 而且重复数十次过滤后, PANI/PTFE复合膜仍具有良好的抗污能力和分离性能.