电解氧化法膨胀石墨形成机理研究

采用现代测试方法对电解氧化法制备的膨胀石墨各阶段产物进行了表征 ,对其形成机理作了一些探讨。结果证实 ,在氧化过程中 ,层间表面的石墨被氧化后 ,与嵌入层间的H2 SO4、H2 O等生成层间化合物 ,该化合物瞬间受高热而分解 ,产生的推力使石墨沿C轴方向膨胀 ,而层平面碳 -碳结构未被破坏。     

氧化程度对微细鳞片可膨胀石墨结构及膨胀性的影响

以平均粒径为19.71μm的天然微细鳞片石墨为原料,通过化学氧化法制备了具有不同氧化程度的可膨胀石墨,采用XRD、FTIR、Raman、SEM等对可膨胀石墨的结构与膨胀性进行了表征。结果表明:当氧化程度较低时制得的微细鳞片可膨胀石墨由石墨、石墨层间化合物和氧化石墨三相组成;随着氧化程度的增加,氧化石墨相含量与可膨胀石墨结构无序程度逐渐增高,石墨层间化合物相含量先增加后减少,石墨相含量则逐渐降低;氧化促使HSO4-或SO42-插入石墨层间,插入层间的HSO4-或SO42-量是决定可膨胀石墨膨胀容积的关键因素,制备的微细鳞片膨胀石墨的膨胀容积可达65.9mL·g-1。     

氧化程度对微细鳞片可膨胀石墨结构及膨胀性的影响

以平均粒径为19.71μm的天然微细鳞片石墨为原料,通过化学氧化法制备了具有不同氧化程度的可膨胀石墨,采用XRD、FTIR、Raman、SEM等对可膨胀石墨的结构与膨胀性进行了表征。结果表明：当氧化程度较低时制得的微细鳞片可膨胀石墨由石墨、石墨层间化合物和氧化石墨三相组成;随着氧化程度的增加,氧化石墨相含量与可膨胀石墨结构无序程度逐渐增高,石墨层间化合物相含量先增加后减少,石墨相含量则逐渐降低;氧化促使HSO₄^-或SO₄^2-插入石墨层间,插入层间的HSO₄^-或SO₄^2-量是决定可膨胀石墨膨胀容积的关键因素,制备的微细鳞片膨胀石墨的膨胀容积可达65.9mL·g^-1。     

氧化程度对氧化石墨结构与阳离子交换容量的影响

通过改进hummers法制备了不同氧化程度的氧化石墨。采用XRD、FTIR及XPS等对不同氧化程度氧化石墨样品的结构特征、含氧官能团种类与含量及阳离子交换容量进行表征。结果表明,石墨经氧化后结构层上键入羟基(C-OH)、环氧基(C-O-C)和羧基(-COOH)等含氧官能团;随氧化程度的增加,石墨结构逐渐全部转化为氧化石墨结构,C-O-C和-COOH的含量逐渐增大,而C-OH的含量先增大后略有减小,阳离子交换容量也表现为先增大后减小,对应的最大值分别为1.70、3.80和4.50 mmol·g-1;氧化石墨碳平面上C-OH发生去质子化反应在层间产生H+,其他阳离子与之交换进入GO层间域,C-OH的含量是影响氧化石墨阳离子交换容量的主要因素,随C-OH含量的增加,氧化石墨样品的阳离子交换容量增大。     

氧化钛-氧化石墨插层结构及其光催化性能(英文)

采用氧化石墨(GO)和硫酸钛作为初始反应物,在低温下(80℃)制备了纳米级的氧化钛-氧化石墨插层(TiO2-GO)复合材料,研究了这一复合材料的紫外光催化性能.结果表明,在采用TiO2-GO插层复合材料对甲基橙溶液进行紫外光催化降解时,其降解效率η=1.17mg·min-1·g-1,明显优于德固赛P25氧化钛粉.通过对TiO2-GO插层复合材料进行X射线衍射(XRD)、傅里叶红外(FT-IR)光谱、X射线光电子能谱(XPS)和场发射扫描电子显微镜(FESEM)等测试,表征了产物的晶相结构、界面状况及其显微结构.结果表明:插层结构中的TiO2晶粒为锐钛矿和金红石的混合相,且锐钛矿相含量大于金红石相含量;氧化石墨层间的含氧基团如C襒O,基本被还原.对TiO2-GO插层复合材料的形成机理以及该材料具有优越光催化性能的原因进行了探讨.     

氧化程度对氧化石墨结构与阳离子交换容量的影响

通过改进hummers法制备了不同氧化程度的氧化石墨。采用XRD、FTIR及XPS等对不同氧化程度氧化石墨样品的结构特征、含氧官能团种类与含量及阳离子交换容量进行表征。结果表明,石墨经氧化后结构层上键入羟基(C-OH)、环氧基(C-O-C)和羧基(-COOH)等含氧官能团;随氧化程度的增加,石墨结构逐渐全部转化为氧化石墨结构,C-O-C和-COOH的含量逐渐增大,而C-OH的含量先增大后略有减小,阳离子交换容量也表现为先增大后减小,对应的最大值分别为1.70、3.80和4.50 mmol·g^-1;氧化石墨碳平面上C-OH发生去质子化反应在层间产生H⁺,其他阳离子与之交换进入GO层间域,C-OH的含量是影响氧化石墨阳离子交换容量的主要因素,随C-OH含量的增加,氧化石墨样品的阳离子交换容量增大。     

油溶性金属Ni纳米微粒的制备与表征

纳米材料的制备、性能与应用已成为近年来的研究热点之一犤１犦。由于在催化、光学和电学材料中的广泛应用，超细单分散的金属微粒的制备与性质已引起人们的广泛兴趣。通常制备金属纳米微粒的方法有两种：一是把固体金属材料分裂为纳米尺寸的颗粒，如机械粉碎、电弧放电及金属原子蒸气沉积犤２犦，用这种方法制备的金属微粒粒径一般都比较大，且粒子尺寸分布宽，另一种是把金属原子制成纳米尺度的颗粒，如乳液聚合法犤３犦、热解犤４犦、γ－射线辐照犤５犦、脉冲电沉积犤６犦和化学还原犤７犦等，这种方法制备的微粒粒径通常分布窄且粒子小…     

溶剂热合成法制备(Zn,Hg)S微晶和薄膜

近年来，由于Ⅱ～Ⅵ族半导体纳米材料的特殊物理、化学性质及其在半导体、光学器件、激光二极管、IR探测器等方面的广泛应用，它们的制备和表征引起了人们越来越大的兴趣犤１～１１犦。现在（Zn，Hg）S微晶正被广泛而深入的研究和应用。例如：一种发蓝光的激光二极管已经设计成功，它包含一夹在两衬层间的活性层，无论是在衬层还是在活性层中都包含有（Zn，Hg）S犤５犦。Sugao也曾报道过一种以（Zn，Hg）S为基础的半导体激光器件犤６犦。Parkin曾用MCl２（M＝Zn，Cd，Hg）和Li２E（E＝O，S，Se，Te）混合热解法制备ME或MxM'yS…     

Mg-Zn-Al三金属类水滑石的合成及其复合氧化物的催化性能

水滑石（[Mg_６Al_２（OH）_(１６)[CO_３·４H_２O）是一种类似于水镁石结构的层状阴离子黏土，其骨架为阳离子，层间为阴离子。如改变骨架中的金属阳离子或在层间引入不同的阴离子，就可形成各种新组成的类水滑石。水滑石对有机分子反应具有较高的催化活性和选择性，且可以作为复合氧化物催化剂的前体，应用广泛。它作为碱催化剂，可用于醇醛缩合；作为氧化还原催化剂，用于水煤气转化、NO的还原、甲烷氧化反应等犤１，２犦。作为一种具有特殊结构的化合物，各种双金属组分的水滑石或类水滑石的合成、性质与应用已受到广泛的重视犤３…     

氧化石墨与石墨烯的制备及其在样品前处理中的应用

石墨烯是继碳纳米管之后出现的新一代碳同素异形体,是碳原子以SP2杂化轨道组成的具有六角形蜂巢晶格结构的二维纳米材料,具有良好的化学稳定性、热稳定性和高比表面积.氧化石墨是用强氧化剂氧化鳞片石墨而获得的石墨衍生物,同样是一层状共价化合物,其表面有丰富的含氧宫能团.近年来,氧化石墨和石墨烯在有机小分子、金属离子和生物大分子分离富集方面的应用已有文献报道.该文简要介绍了氧化石墨以及石墨烯的制备方法,并详细概述了其在固相萃取、固相微萃取、磁性固相萃取、搅拌棒吸附萃取等样品前处理技术中的应用.     

氧化石墨的制备及其有机化处理

Graphite oxide(GO) was successfully prepared by using expandable graphite， which is a new starting material instead of the normally adopted natural graphite. XRD and XPS data indicated that， in the same reaction condition due to the application of expandable graphite， the extent of oxidation for the product， GO， was considerably en-hanced and the period required for oxidation was greatly shortened. In addition， the prepared GO was modified by surfactant， that is the new sample， S-GO， was obtained. As a consequence the extended interlayer space has proved itself to be successfully intercalated by the surfactant.     

膨胀石墨制备方法的研究进展

综述了膨胀石墨制备方法的研究现状,重点阐述了两种常用制备方法:(1)以天然鳞片石墨为原料,先经氧化制得可膨胀石墨,再经膨化处理得膨胀石墨;(2)将氧化和膨胀同时进行的爆炸法。分析了不同制备方法的优劣。并对膨胀石墨的制备工艺进行了展望。参考文献48篇。     

PS colloidal particles stabilized by graphene oxide

Exfoliated graphene oxide (GO) sheets with hydrophilic functional groups on the surface were prepared by the oxidation of graphite. Because of the hydrophilic groups on the sheets and the hydrophobic carbon surface, GO sheets were located at the oil-water interface and could be used as a stabilizer in Pickering emulsions. After the Pickering emulsion polymerization of styrene, PS colloidal particles with GO sheets on the surface were prepared. The size of the GO sheets exerts an important influence on the preparation of PS colloidal particles. Small GO sheets located at the liquid-liquid interface and GO-stabilized PS colloidal particles were prepared; however, for large GO sheets, smaller PS colloidal particles prepared on the GO surface were observed. Transmission electron microscopy (TEM), scanning electron microscopy (SEM), and X-ray photoelectron spectroscopy (XPS) were used to characterize the structure and morphology of the colloidal particles. TEM, SEM, and XPS results all suggest the successful preparation of GO-stabilized PS colloidal particles.     

氧化石墨的谱学表征及分析

采用改进的Hummers法,通过改变氧化剂用量获得不同氧化程度的氧化石墨,用X射线衍射(XRD)、红外光谱(FTIR)和拉曼光谱(Raman)对产物进行结构和谱学特性的表征,并结合数学分析软件对部分红外和拉曼数据进行分峰拟合。结果表明,石墨经氧化后形成了含有C-OH、-COOH和C-O-C等官能团的石墨层间化合物;氧化剂用量较少时,石墨片层插层氧化不完全,产物的结构中仍存在未被氧化的原石墨周期性结构;随着氧化剂用量的增加,氧化石墨产物的XRD图中原石墨(002)衍射峰逐渐消失,结构中含氧官能团的量逐渐增加,产物的亲水性也逐渐增强;通过对红外光谱的拟合发现,氧化石墨样品在3 198 cm^-1附近有一个红外吸收峰,应归属于C-OH中OH的伸缩振动;随着氧化剂用量的增加,所得氧化石墨产物的拉曼光谱中D峰与G峰的强度积分比R(I_D/I_G)逐渐增大,产物结构中sp²平面域的平均尺寸逐渐减小。     

氧化石墨：制备及去除阳离子染料的性能

以石墨粉为原料按Hummers氧化法制备氧化石墨,借助X射线衍射仪(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、傅里叶变换红外光谱法(FTIR)和低温氮吸附-脱附对氧化石墨的结构和形貌进行了表征。结果表明,氧化石墨是不平整的、具有一定层状结构的褶皱片状,在其表面存在着许多含氧的官能团如:环氧基、羟基、羧基。此外还研究了氧化石墨对阳离子染料的吸附性能,结果表明:吸附过程的等温模型符合Langmuir等温式,对甲基紫、甲基绿、中性红这3种阳离子染料的最大饱和吸附量分别为:741,446和368 mg.g-1;对阳离子染料的吸附过程符合二级动力学方程。氧化石墨作为一种吸附剂能有效的去除阳离子染料与其较高的比表面积和与阳离子染料的静电吸引有关。     

天然石墨负极的改性研究

天然石墨作为锂离子二次电池负极材料得到了广泛关注.针对天然石墨负极的体积效应和表面活性基团的不利影响,通过溴化和高温煅烧处理制备石墨插层化合物中间体和适度膨胀的石墨样品以改善其倍率和循环寿命.样品利用X射线衍射(XRD)、扫描式电子显微镜(SEM)和比表面积检测(BET)分析其结构特征,结果表明膨胀石墨样品石墨层剥离晶粒增大.恒流充放电和循环伏安扫描测试结果表明改性后的石墨样品其倍率性能和循环稳定性均得到明显改善.     

Improvement of ammonia sensing properties of polypyrrole by nanocomposite with graphitic materials

The more sensitive and rapid ammonia gas sensors were prepared with nanocomposites of polypyrrole (PPy) and graphitic materials such as graphite, graphite oxide (GO), and reduced graphene oxide (RGO). Pyrrole was polymerized uniformly on the surface of graphitic materials by in situ polymerization method. The structures of nanocomposites were studied by scanning electron microscopy, X-ray diffraction, and X-ray photoelectron spectroscopy indicating the well-exfoliated GO and RGO in PPy matrix with favorable interfacial interaction. PPy/RGO nanocomposite showed the highly improved response in detecting ammonia gas mainly due to the effective electron charge transfer between PPy and ammonia and the efficient transfer of electrical resistance variation by the uniformly dispersed conductive RGO in PPy. PPy/RGO nanocomposite gas sensor also showed the excellent reproducibility in ammonia sensing behavior during the recovery process at lower temperature of 373 K.     

Influence of phosphorus‐grafted expandable graphite on the flame‐retardant property of UHMWPE composite

In this paper, an efficient flame retardant, 9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene‐10‐oxide (DOPO) was covalently grafted onto the surface of expandable graphite (EG). The resultant DOPO‐grafted expandable graphite (EG‐g‐DOPO) was characterized by Fourier transform infrared spectroscopy, energy dispersive spectroscopy, and X‐ray photoelectron spectroscopy (XPS), respectively. The thermal stability of EG‐g‐DOPO was also evaluated by thermogravimetric analysis (TGA). Moreover, a series of flame‐retardant ultra‐high‐molecular‐weight polyethylene (UHMWPE) composites with various concentrations of EG‐g‐DOPO were prepared and evaluated. The results show that the UHMWPE composite with 20 wt% EG‐g‐DOPO possesses a satisfactory UL‐94 flame‐retardant grade (V‐0) and a high limiting oxygen index (30.6%). The residual char of the UHMWPE composite with higher EG‐g‐DOPO concentration shows more compact and integrated, providing an efficient barrier for heat release.     

石墨及石墨/双马来酰亚胺减摩树脂复合材料的XRD研究

利用X射线衍射对鳞片石墨、可膨胀石墨、膨胀石墨和纳米石墨薄片以及石墨 /双马来酰亚胺、纳米石墨薄片 /双马来酰亚胺减摩复合材料进行了研究,探讨它们之间在结构上的关系以及以复合材料中双马来酰亚胺预聚体对石墨层间距的影响.实验结果表明:可膨胀石墨中插层剂的插入除了增大石墨层间距外,还减小相邻插层剂未插入的石墨层间距;膨胀石墨的结构除了保留强度很弱的石墨特征峰外,还有大量强度极其微弱、层间距大小不一的峰;超声波对膨胀石墨的结构有整合、均匀化作用;双马来酰亚胺预聚体不能插入鳞片石墨层间,而能插入纳米石墨薄片的层间.     

Evidence of graphitic AB stacking order of graphite oxides

Graphite oxide (GO) samples were prepared by a simplified Brodie method. Hydroxyl, epoxide, carboxyl, and some alkyl functional groups are present in the GO, as identified by solid-state 13C NMR, Fourier-transform infrared spectroscopy, and X-ray photoemission spectroscopy. Starting with pyrolytic graphite (interlayer separation 3.36 A), the average interlayer distance after 1 h of reaction, as determined by X-ray diffraction, increased to 5.62 A and then increased with further oxidation to 7.37 A after 24 h. A smaller signal in 13C CPMAS NMR compared to that in 13C NMR suggests that carboxyl and alkyl groups are at the edges of the flakes of graphite oxide. Other aspects of the chemical bonding were assessed from the NMR and XPS data and are discussed. AB stacking of the layers in the GO was inferred from an electron diffraction study. The elemental composition of GO prepared using this simplified Brodie method is further discussed.