木薯羧甲基淀粉对铜离子的吸附性能

采用搅拌球磨机对木薯淀粉进行机械活化,以活化60 min的木薯淀粉为原料,干法合成羧甲基淀粉吸附剂。考察羧甲基淀粉的取代度、溶液的pH值、Cu2+的初始浓度、吸附时间、羧甲基淀粉的投加量等因素对羧甲基淀粉吸附Cu2+性能的影响。结果表明,该羧甲基淀粉对Cu2+有很好的吸附作用;用取代度为0.841的羧甲基淀粉处理含Cu2+的废水,在pH=7.0、羧甲基淀粉的投加量50.00 mg/L、吸附时间15 min时,羧甲基淀粉对废水中Cu2+的吸附率高达98.80%,处理后的水质达到国家污水综合排放标准(GB8978-1996)中一级标准要求。     

Metal adsorption of carboxymethyl cellulose/carboxymethyl chitosan blend hydrogels prepared by Gamma irradiation

Blend hydrogels based on the carboxymethyl cellulose (CMC) and carboxymethyl chitosan (CMCts) were prepared by γ-irradiation of a high concentrated CMC/CMCts aqueous solution. Properties of the hydrogels, such as gel fraction, swelling ratio, gel strength, and metal adsorption for Pb and Au were investigated. The gel fraction increased with increasing dose, while the swelling ratio decreased with increasing it. The obtained blend hydrogels had high adsorption performance which was controlled by adjusting the composition of CMC/CMCts.     

羧甲基壳聚糖吸附痕量汞研究

研究羧甲基壳聚糖对Hg^2＋的吸附作用, 探讨了溶液的pH、反应时间、温度、样品体积、共存组分等因素对吸附率的影响. 实验表明, 在pH＝4时, 羧甲基壳聚糖对Hg^2＋的吸附性能很好, 其饱和吸附容量为140 mg/g, 方法的相对标准偏差为8.5%. 用于实际水样分析时, 回收率达94%以上.     

Structure and properties of biodegradable carboxymethyl cellulose films containing silver nanoparticles

Silver nanoparticles stabilized in a solution of sodium carboxymethyl cellulose with a degree of substitution of 0.85 and a degree of polymerization of 600 have been synthesized. The structuring; physical, chemical, and mechanical properties; and antimicrobial activities of films prepared from sodium carboxymethyl cellulose solutions containing silver nanoparticles have been studied. The shapes, quantities, and sizes of the silver nanoparticles occurring in the sodium carboxymethyl cellulose films were determined with the use of transmission electron microscopy, atomic force microscopy, and UV spectroscopy. It was found that an increase in the concentration of silver nitrate in sodium carboxymethyl cellulose solutions, as well as photoirradiation of the films, leads to the changes in the sizes and shapes of silver nanoparticles. The shapes, sizes, and quantities of silver nanoparticles determine their biological activity. An increase in the quantity of 5- to 25-nm silver nanoparticles was found to enhance the microbicidal activities of the carboxymethyl cellulose films.     

Adsorption of carboxymethyl cellulose on polymer surfaces: evidence of a specific interaction with cellulose

The adsorption of carboxymethyl cellulose (CMC), one of the most important cellulose derivatives, is crucial for many scientific investigations and industrial applications. Especially for surface modifications and functionalization of materials, the polymer is of interest. The adsorption properties of CMC are dependent not only on the solutions state, which can be influenced by the pH, temperature, and electrolyte concentration, but also on the chemical composition of the adsorbents. We therefore performed basic investigation studies on the interaction of CMC with a variety of polymer films. Thin films of cellulose, cellulose acetate, deacetylated cellulose acetate, polyethylene terephthalate, and cyclo olefin polymer were therefore prepared on sensors of a QCM-D (quartz crystal microbalance) and on silicon substrates. The films were characterized with respect to the thickness, wettability, and chemical composition. Subsequently, the interaction and deposition of CMC in a range of pH values without additional electrolyte were measured with the QCM-D method. A comparison of the QCM-D results showed that CMC is favorably deposited on pure cellulose films and deacetylated cellulose acetate at low pH values. Other hydrophilic surfaces such as silicon dioxide or polyvinyl alcohol coated surfaces did not adsorb CMC to a significant extent. Atomic force microcopy confirmed that the morphology of the adsorbed CMC layers differed depending on the substrate. On hydrophobic polymer films, CMC was deposited in the form of larger particles in lower amounts whereas hydrophilic cellulose substrates were to a high extent uniformly covered by adsorbed CMC. The chemical similarity of the CMC backbone seems to favor the irreversible adsorption of CMC when the molecule is almost uncharged at low pH values. A selectivity of the cellulose CMC interaction can therefore be assumed. All CMC treated polymer films exhibited an increased hydrophilicity, which confirmed their modification with the functional molecule.     

Buildup mechanism of carboxymethyl cellulose and chitosan self-assembled films

Films with different numbers of layers have been built by alternating the adsorption of carboxymethyl cellulose (CMC) and chitosan (CHI) at different pH levels. The adsorption process was recorded by quartz crystal microbalance (QCM). The results showed that under all pH conditions considered, the growth of the films is nonlinear. The film construction performed at pH 4.0 (preferred assembly pH) with different numbers of bilayers (CMC/CHI as one bilayer) was also observed step by step by atomic force microscopy (AFM). Comparing the growth process from QCM with the surface morphological changes from AFM shows the existence of an inhomogeneous structure for the first nine bilayers, and, after a coalescence of islands, an increase in the number of bilayers was demonstrated. The possible growth mechanism was also evaluated.     

Adsorption behavior of carboxymethyl starch on titanium dioxide surfaces

The adsorption of carboxymethyl starch (CMS) on titanium dioxide surface from aqueous solution of electrolyte was investigated by adsorption and electrokinetics mobility measurements. Zeta potential measurements showed that the addition of CMS resulted in a shift of isoelectric point to the more acidic region, indicating the adsorption of CMS from the aqueous solution onto titanium dioxide surface. The positively charged and hydrophilic surface sites of titanium dioxide favor the adsorption of CMS molecules. The adsorption capacity of CMS on titanium dioxide surface was found to be controlled by the number of functional group on CMS that promotes surface charge CMS adsorption in agreement with Langmuir isotherm. For the adsorption of CMS, the pseudo-second-order kinetics of chemical reaction provides the best correlation of the experimental data.     

Effect of carboxymethyl cellulose and ionic strength on stability of mineral suspensions in potash ore flotation systems

The adsorption of sodium carboxymethyl cellulose from aqueous solutions varying in ionic strength from that of distilled water to 50% NaCl/KCl brine (about 3.5 mol/dm(3)) onto illite and dolomite has been studied. The purpose of this work was to investigate the solvency effects in the phenomena underlying the potash flotation process that is carried out in saturated brine. Based on viscosity measurements, the adsorption results were analyzed in terms of a simple model of polymer macromolecules in solution. Suspension stability measurements carried out concomitantly with adsorption tests showed the ranges of carboxymethyl cellulose concentration over which the tested suspensions either were aggregated or were restabilized.     

Kinetics and adsorption behavior of carboxymethyl starch on alpha-alumina in aqueous medium

The adsorption of carboxymethyl starch (CMS) at the alpha-alumina/aqueous solution interface has been investigated through adsorption studies, electrokinetics mobility measurements, and FTIR spectroscopy. Zeta potential measurements show that the addition of CMS results in a more dramatic increase in the absolute zeta potential in the alkaline region, as well as a shift of the isoelectric point to lower values, indicating the adsorption of CMS from the aqueous solution onto the alumina surface. The positive hydrophilic surface sites of alumina are responsible for the adsorption of CMS molecules. The adsorption of CMS is possible after charge reversal by the addition of excess CMS. Nearly 30 min of contact time are found to be sufficient for the adsorption of CMS to reach equilibrium. CMS adsorption follows a Langmuir isotherm with adsorption capacities of 91.74 mg CMS per gram of alpha-alumina. For the adsorption of CMS, pseudo-second-order chemical reaction kinetics provides the best correlation with the experimental data. FTIR analysis indicated that CMS forms outer complexes with alumina surfaces depending on the shifting of the asymmetric and symmetric bands.     

Composites comprising cholesterol and carboxymethyl cellulose

Whereby cholesterol presents one of the major fatty substances in human body, carboxymethyl cellulose is a water-soluble derivative of cellulose, the most abundant dietary fiber. Whereas on one hand in vivo precipitation of cholesterol is the major cause of atherosclerosis, dietary fibers are on the other hand known for their ability to clean the fatty plaque deposited on intestinal pathways, and prevent its build-up in other critical areas within the organism. In this work, a method for the preparation of a composite material comprising cholesterol and carboxymethyl cellulose from 1-hexanol/water biphase mixtures is reported. Specificity of the interaction between the composite components in the given conditions of synthesis inhibits the tendency of solid cholesterol to adopt typical plate- or needle-shaped morphologies. Instead, control of the thixotropic behavior of the constituent polymer phase leads to the formation of bubbling, multi-layered cholesteric films. In view of the major illnesses that involve biological precipitation of cholesterol crystals, these findings may be considered as pointing towards the interactional specificity of potential chemotherapeutic and/or nutritional significance. Scanning electron microscopy, thermal and diffractometric analyses were performed as parts of the characterization of the prepared material.     

Comparison of hydroxypropyl and carboxymethyl guar for the preparation of nanocellulose composite films

The gas barrier and mechanical properties are crucial parameters for packaging materials, and they are highly correlated to the molecular interactions in the polymer matrix. To improve these properties of TEMPO-oxidized cellulose nanofibers (TOCNs) composite films, we studied the effect using hydroxypropyl guar (HPG) or carboxymethyl guar (CMG) in the preparation of TOCN composite films, which were made by following the solution-casting method. The subsequent film characterizations were carried out by UV–Vis spectra, scanning electron microscopy, oxygen and water vapor permeability measurements, tensile and thermogravimetric analyses. SEM results showed that CMG-based films had denser structures than their HPG counterparts. Moreover, the improved hydrogen bonding of the CMG-based films was partially responsible for the improved gas barrier performance, tensile strength and thermal stability. These results support the conclusion that CMG had advantages over HPG when used in the preparation of TOCNs packaging composite films.     

Properties of films, solutions, and gels prepared from sodium carboxymethyl cellulose blends with synthetic polymers

An extremal dependence of the intrinsic viscosity of poly(vinyl alcohol) blends with sodium carboxymethyl cellulose and polyacrylamide on composition has been established. A correlation between the viscosity properties of solutions and mechanical properties of films made of sodium carboxymethyl cellulosepoly(vinyl alcohol) blends is observed that is indicative of the interpolymer interaction in these systems. The obtained regularities can be used to produce high-modulus coordination-crosslinked gels based on these blends.     

Compatibility of carboxymethyl cellulose ionized to various degrees with poly-N-vinylformamide in composite films

Composite films were obtained from aqueous solutions of blends of carboxymethyl cellulose ionized to various degrees and poly-N-vinylformamide. The composition ranges in which the polymers are compatible were determined by solvent vapor sorption and by dynamic mechanical analysis. The heat resistance of the films and the interaction of the polymers in the solid state were examined by DSC, TGA, and Fourier IR spectroscopy.     

Topochemical modification of cotton fibres with carboxymethyl cellulose

Adsorption of carboxymethyl cellulose (CMC) as a method to introduce charged (ionizable) groups onto cellulose cotton fibre surfaces was investigated. The method was based on application of a previously published method used for wood fibres. The amount of adsorbed ionizable groups was determined indirectly by analysis of CMC in solution by the phenol–sulphuric acid method and directly by conductometric titration of the fibres. Results from the two methods correlated well. The molecular weight and purity of the CMC had an influence on its adsorption onto cotton; high molecular weight CMC was preferentially adsorbed. The adsorbed charge correlated linearly with the amount of CMC adsorbed. The total charge of the cotton fibres could be increased by more than 50% by adsorption of CMC. It is expected that this modification procedure can be used in a wide spectrum of practical applications. Lidija Fras Zemljič and Karin Stana-Kleinschek are the members of the European Polysaccharide Network of Excellence (EPNOE).     

Properties of carboxymethyl cellulose aqueous solutions with nanoparticle additives and the related composite films

The rheological properties of carboxymethyl cellulose aqueous solutions containing small amounts of purified montmorillonite and bentonite nanoparticles are studied. The viscosity of mixed solutions decreases after addition of 1 wt % nanoparticles. X-ray diffraction analysis shows that the films contain nanoparticles in the exfoliated state. An examination of the FTIR spectra of composite films suggests a shift in the absorption band due to Si-O groups. This phenomenon may be explained both by a change in the permittivity of the nanoparticle environment and by the formation of hydrogen bonds between Si-O groups and functional groups of cellulose ether. It is shown that the content of the added nanoparticles influences the mechanical characteristics of the films prepared from the systems of interest.     

Miscibility and biodegradability of silk fibroin/carboxymethyl chitin blend films

Blend films of silk fibroin and carboxymethyl chitin were prepared by solution casting using water as a cosolvent. The blend films were subjected to post-treatment with an aqueous methanol solution to induce beta-sheet formation of silk fibroin. The miscibility of the blend films both before and after methanol treatments was investigated in terms of chemical interactions, morphologies, thermal properties, and crystal structures by using FTIR spectroscopy, SEM, DSC, and XRD. The results indicate that the blend between silk fibroin and CM-chitin was semi-miscible because only the amorphous parts of the polymers were compatible with each other. The enzymatic degradation showed that the incorporation of CM-chitin enhanced biodegradability and swelling ability of silk fibroin.     

Properties of water-soluble carboxymethyl chitosan film modified by hydrophobic poly(propylene glycol)

A series of water-soluble carboxymethyl chitosan (CMCS)/poly(propylene glycol) (PPG) blend films with various CMCS/PPG mole ratios were prepared by the solution casting method. Morphology of the CMCS/PPG blend films was investigated by scanning electron microscopy (SEM). Thermal, mechanical, and chemical properties of the CMCS/PPG blend films were studied by differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), tensile tests, and contact angle tests. It was found that the introduction of PPG can markedly affect the morphology and the properties of CMCS films.     

The effect of adsorbed carboxymethyl cellulose on the cotton fibre adsorption capacity for surfactant

The research reported in this paper demonstrates that the capacity of cotton fibres to adsorb cationic surfactants as well as the rate of the adsorption process can be increased by adsorbing carboxymethyl cellulose (CMC) onto the fibre surfaces; in addition, the adsorption can be restricted to the fibre surface. CMC was deposited by means of adsorption from an aqueous solution. The adsorption of N-cetylpyridinium chloride (CPC) from an aqueous solution onto the CMC-modified fibres was measured using UV-spectrometric determination of the surfactant concentration in the solution. Adsorption onto the cotton fibres was studied in a weakly basic environment (pH 8.5) where cotton fibres are negatively charged and the CPC ion is positively charged. Modification of the fibres by adsorption of CMC introduces new carboxyl groups onto the fibre surfaces, thereby increasing the adsorption capacity of the fibres for CPC. The initial rate of adsorption of CPC increased proportionally with the amount of charge; however, this rate slowed down at high degrees of coverage on fibres with a high charge. The adsorption of cationic surfactant to the anionic surface groups was stoichiometric, with no indication of multilayer or admicelle formation. It was evident that the acidic group content of the fibres was the primary factor determining cationic surfactant adsorption to these fibres.     

Nanofibrillated cellulose/carboxymethyl cellulose composite with improved wet strength

In this paper, nanofibrillated cellulose/carboxymethyl cellulose (CMC) composite films were prepared using tape casting. The obtained transparent films showed shear induced partial alignment of fibrils along the casting direction, resulting in birefringence in cross polarized light. The carboxyl groups of CMC could be further utilized to create ionic crosslinking by treatment with glycidyl trimethyl ammonium chloride (GTMA). The GTMA treated composite films had improved mechanical properties both in wet and dry state. The chemical composition and morphologies of composites were analyzed with X-ray photoelectron spectroscopy, elemental analysis, scanning electron microscopy and wide-angle X-ray scattering.     

The nature of thermodynamic compatibility of components of aqueous solutions of starch and cellulose carboxymethyl derivatives

The Gibbs free energy, enthalpy, and entropy of mixing of starch and carboxymethyl derivatives of starch and cellulose with water were determined by sorption and calorimetry methods at 25°C throughout the entire range of compositions. The contributions due to the equilibrium intermolecular interactions and relaxation of a metastable glassy structure were separated. The relaxation of the metastable structure taking place during physical adsorption of the first portions of water on polymers makes a negative contribution to all thermodynamic functions of mixing. The contribution of equilibrium interactions, which includes pair nonviolent interactions of units and water molecules and electrostatic interactions of ions, is positive for the enthalpy and entropy of mixing. In this case, the positive entropy values exceed those of enthalpy, which is responsible for the thermodynamic compatibility. Thermodynamic analysis of the processes of dissolution of starch, carboxymethyl starch and carboxymethyl cellulose sodium salts showed that, contrary to the popular point of view, the compatibility of polysaccharides and their derivatives with water is based not on the enthalpy, but entropy nature and is strengthened additionally owing to relaxation of the metastable glassy structure of polymers.