聚芳酰胺-多壁碳纳米管混合物固定漆酶电极的电化学行为

以聚芳酰胺-多壁碳纳米管混合物为载体,利用漆酶表面氨基与聚芳酰胺主链端羧基的共价偶联以及碳纳米管与漆酶间的疏水作用,构筑了具有较高稳定性和电催化活性的漆酶修饰电极.并对该固酶修饰电极的固酶量、酶活力、电化学行为及其电催化氧还原的性能进行了表征.对漆酶分子具有亲和力的聚芳酰胺芳环结构及聚芳酰胺端羧基与漆酶表面氨基的共价偶联避免了漆酶的脱落和变性.而碳纳米管与聚芳酰胺的混合使得该三维修饰电极具有良好的电子导电性,并成功地实现了漆酶的氧化还原活性位与电极之间的直接电荷转移,这一点可由在0.73和0.38V附近观察到漆酶的T1和T2(漆酶的T1,T2铜活性位的形式电位分别为0.78和0.39V(vsNHE))铜活性位的两对氧化还原峰确认.漆酶的担载量为56.0mg·g-1,具有电化学活性的漆酶占总担载漆酶量的68%.在pH=4.4磷酸盐缓冲溶液中,该修饰电极上氧气还原的起始电位为0.55V,其对氧气的米氏常数KM为55.8μmo·lL-1,对氧气的检测限为0.57μmo·lL-1.在4℃下保存两个月后能实现直接电荷转移的漆酶量仅下降了14%左右而氧还原超电势提高了约50mV.结果表明该修饰电极有望用作酶基生物燃料电池的阴极和电流型氧气传感器.     

高分子聚合物-多壁碳纳米管复合物固定漆酶及其在玻碳电极上的直接电子迁移

采用不同结构的高分子聚合物与纯化的多壁碳纳米管(MWCNTs)共混的方法,制备得到聚合物非共价功能化多壁碳管复合物,测定了这些载体对漆酶(lac)的担载量、固定漆酶的比活力及稳定性.以固定漆酶的复合物修饰玻碳(GC)电极后,采用循环伏安法研究这些电极在无氧磷酸盐缓冲液(PBS)中的直接电化学行为及催化氧还原活力,粗略地测定了固定漆酶与电极间电子转移的速率常数.实验结果表明,当聚合物中含亲漆酶基团或能与漆酶活性中心发生相互作用的官能团时利于直接电子转移,而且复合物固定漆酶保持了游离漆酶的天然构象.这些电极中,lac/NIPAM-co-BPCP-M WCNTs/GC(NIPAM-co-BPCP:N-烯丙基-1-苯甲酰基-3-苯基-4,5-2H-4-甲酰胺基吡唑-co-N-异丙基丙烯酰胺)在无氧PBS中发生直接电子转移的式电位(605mV)更接近漆酶活性中心的式电位(580mV),具有较快的异相电子转移速率(0.726s-1),较高的漆酶担载量(103.5mg/g)和固定漆酶比活力(1.68U/mg),较高的催化氧还原能力(氧还原起始电位820mV,在650mV时的催化峰电流为85.5μA)以及良好的重复使用性和长期使用性.     

多壁碳纳米管-Nafion膜修饰铂电极的电化学性质

使用多壁碳纳米管(MWCNTs)和Nafion溶液制备了多壁碳纳米管-Nafion膜修饰的铂电极。运用扫描电子显微镜(SEM)对多壁碳纳米管、Nafion膜、多壁碳纳米管-DMF膜和多壁碳纳米管-Nafion膜进行了形貌表征。通过电化学系统研究了铁氰化钾在多壁碳纳米管-Nafion膜修饰电极、多壁碳纳米管-DMF修饰电极以及未修饰铂电极的表面电化学行为。结果显示,多壁碳纳米管-Nafion膜修饰的电极对铁氰化钾有显著的电化学增强作用,于0.185 V处形成了一个尖锐的还原特征峰,比未修饰的铂电极还原峰增强近8.7倍;在0.231 V处形成了一个较强的氧化特征峰,比未修饰的铂电极氧化峰增强近2.7倍。由于多壁碳纳米管的比表面积大,利用其与Nafion修饰的电极能增强电子传输效率,使测定的峰电流增大,从而提高灵敏度,有助于检测低浓度物质。进一步研究发现,铁氰化钾在未修饰的铂电极表面反应为可逆反应,而在MWCNTsNafion膜修饰后的电极表面反应为不可逆反应。     

壳聚糖-g-N-羧甲基-2-硫代-4,5-2H咪唑啉酮-多壁碳纳米管复合物固定漆酶基化学传感器的性能

通过壳聚糖-g-N-羧甲基-2-硫代-4,5-2H咪唑啉酮(CTS-g-N-CSIDZ)非共价功能化多壁碳纳米管(MWCNTs)的方式制备固定漆酶载体,该复合物载体主要通过物理吸附和漆酶活性中心与载体上配体之间的配位作用来固定漆酶,较大程度地保持了游离漆酶活性位原始构象.将固定了漆酶的复合物附着在裸玻碳电极上便构筑了复合物固定漆酶修饰玻碳电极.在以分光光度法测定了这种复合物载体对漆酶的担载量、固定漆酶比活力、稳定性、重复使用性及其催化2,6-二甲氧基苯酚(DMP)氧化动力学参数的基础上,还对基于此种复合物固定漆酶修饰玻碳电极作为化学传感器(以DMP作为底物)的性能进行了研究.结果表明,该复合物具有较高的固酶担载量(81.7 mg/g)和固定漆酶比活力(1.33 U/mg);而作为电化学传感器的复合物固定漆酶修饰玻碳电极对底物DMP具有较高的亲和力(对DMP的米氏常数KM是0.0918 mmol/L),较高的灵敏度( 3680 mA· L/mol),较低的检测限(3.3×10-4 mmol/L),较高的响应选择性,良好的重现性、重复使用性和长期稳定性.这种漆酶基电极有望用作电流型特定结构的酚类传感器.     

基于明胶-碳纳米管的辣根过氧化物酶修饰电极在离子液体中的直接电化学

制备了明胶(Gel)-多壁碳纳米管(MWCNTs)纳米复合物,将其修饰在玻碳电极表面,再吸附辣根过氧化物酶(HRP),制得明胶-多壁碳纳米管-辣根过氧化物酶修饰电极(Gel-MWCNTs-HRP/GCE).该修饰电极在PBS中的循环伏安图上出现了一对峰形良好、几乎对称的氧化还原峰,式量电位为-0.356 V(vs.SCE),表明包埋在Gel-MWCNTs中的HRP与电极之间发生了直接电子传递.当扫速在20 ～ 180 mV/s时,氧化峰电流(Ipa)与还原峰电流(Ipc)均与扫速成正比,表明电极过程是受电子传递速率控制的表面传质过程.运用循环伏安法研究了修饰电极的电化学特性,探讨了工作电位、pH值、干扰物质等对修饰电极的影响.实验结果表明,HRP在修饰电极表面能有效和稳定地进行直接电子转移,并保持了其对过氧化氢(H2O2)的生物催化活性.进一步研究发现,在含有亲水性离子液体1-丁基-3-甲基咪唑四氟硼酸([BMIM]BF4)的溶液中,修饰电极对H2O2显示出更灵敏的催化活性,其线性范围为2.0×10-7～0.13 mol/L,检出限(S/N =3)为2.3×10-8 mol/L.该电极具有灵敏度高、重现性及稳定性好、使用寿命较长等优点,同时还显示了较好的抗干扰能力.     

槲皮素在多壁碳纳米管修饰碳糊电极上的电化学行为及其与脱氧核糖核酸的相互作用

采用循环伏安法和差分脉冲伏安法研究了槲皮素在多壁碳纳米管修饰碳糊电极上的电化学行为。结果表明:槲皮素多壁碳纳米管修饰碳糊电极上均能产生一对氧化还原峰,氧化峰电位和还原峰电位分别为0.488,0.348V,氧化峰电流是裸多壁碳纳米管修饰碳糊电极氧化峰电流的5.3倍,多壁碳纳米管对槲皮素有良好的催化作用。槲皮素在修饰电极上的电化学反是2质子,2电子反应过程。采用中性红为探针研究了槲皮素与脱氧核糖核酸之间的相互作用,结果表明两者可通过嵌插方式相结合。     

嵌入式碳纳米管石墨电极测定灯盏花素的研究

制备嵌入式多壁碳纳米管修饰石墨电极,利用循环伏安法(CV)研究灯盏花素在嵌入式多壁碳纳米管修饰石墨电极(ESCFE)上的电化学氧化行为,结果表明,灯盏花素在修饰电极上出现一对明显的准可逆氧化还原峰,峰电位分别为Epa=0.17 V和Epc=0.05 V(△E=0.12 V),峰电流分别为ipa=42.79μA,ipc=...     

基于纳米金与碳纳米管-纳米铂-壳聚糖纳米复合物固定癌胚抗原免疫传感器的研究

采用纳米金(nano-Au)、多壁碳纳米管-纳米铂-壳聚糖的纳米复合物(MWNT-Pt-CS)及电子媒介体硫堇(Th)固载抗体制得高灵敏癌胚抗原免疫传感器．首先, 于壳聚糖溶液中用NaBH4还原H2PtCl6, 并将多壁碳纳米管分散于其中制得碳纳米管-纳米铂-壳聚糖纳米复合物, 并将其滴涂在玻碳电极上成膜; 然后, 吸附电子媒介体硫堇制得硫堇/碳纳米管-纳米铂-壳聚糖(Th/MWNT-Pt-CS)修饰电极．利用壳聚糖和硫堇分子中大量的氨基固定纳米金并吸附癌胚抗体(anti-CEA); 最后, 用辣根过氧化物酶(HRP)封闭活性位点从而制得高灵敏电流型免疫传感器．在优化的实验条件下, 该传感器响应的峰电流值与癌胚抗原(carcinoembryonic antigen)浓度在0.5～10和10～120 ng/mL的范围内保持良好的线性关系, 检测限为0.2 ng/mL．     

功能化碳纳米管的电化学性质及在6-巯基嘌呤分析检测中的应用

采用修饰单壁碳纳米管(SWNT、SWNT.COOH或SWNT-OH)及多壁碳纳米管(MwNT、MWNT-COOH或MWNT-OH)的石墨电极研究配位阴离子[Fe(CN)6]3-和配位阳离子[Co(phen)3]3+的电化学行为与吸附性能,借助[Co(phen)3]3+在碳纳米管(CNT)的强吸附特性制备[Co(phen)3]3+/CNT/C修饰电极,以其应用于6-MP的分析检测.结果表明:1)在CNT修饰电极上[Fe(CN)6]3-/4-.呈现很好的氧化还原可逆性,而[Co(phen)3]3+则显示明显的吸附控制特征.2)[Co(phen)3]3+在多壁碳纳米管修饰电极上的吸附量较单壁碳纳米管大,但经羧基化或羟基化后,吸附量减小,而且在羧基化表面的吸附量较羟基化的大.3)[Co(phen)3]3+与6-MP间存在明显的相互作用,其配位产物的还原峰电流与6-MP浓度呈线性关系.     

β-环糊精/碳纳米管修饰电极上盐酸异丙嗪的电化学行为研究

研究盐酸异丙嗪在β-环糊精修饰多壁碳纳米管玻碳电极上的电化学行为,建立了一种新的测定盐酸异丙嗪的电化学分析方法.在碳纳米管和β-环糊精的协同作用下,用循环伏安法研究了盐酸异丙嗪在修饰电极上的氧化还原特性,结果表明该修饰电极对盐酸异丙嗪具有显著的催化氧化作用.在pH=5.4的磷酸盐缓冲溶液中,氧化峰电流与盐酸异丙嗪浓度在...     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.     

Cu0-catalysed 1,3-dipolar cycloadditions of α-amino acid derived N,N-cyclic azomethine imines to ynones

A series of 20 CuAIAC reactions between eight 4-acylamino substituted pyrazolidine-3-one-1-azomethine imines and four terminal ynones were performed using Cu⁰ as catalyst. The corresponding fluorescent cycloadducts were obtained in very high yields upon simple workup. Thus, Cu-metal turned out to be a better catalyst than Cu^I in terms of yield and ease of isolation. Availability of azomethine imines, mild reaction conditions, and simple workup enable a “click” access to libraries of densely substituted 2,3-dihydro-1H,5H-pyrazolo[1,2-a]pyrazol-1-ones. Reactivity of differently substituted dipoles was evaluated experimentally and by quantum chemical methods (DFT).