通过接枝苄基磺酸在MCM-41上固载手性Mn(salen)配合物

首先通过两步后合成处理,在MCM-41上接枝苄基磺酸;然后,以苄基磺酸为过渡产物,用手性Mn(salen)配合物修饰处理,得到了苄基磺酸轴向负载手性Mn(salen)配合物的MCM-41;实现了在廉价且温和条件下均相手性Mn(salen)催化剂的非均相化。采用X射线衍射(XRD)、低温N₂吸附-脱附、红外光谱、热重-差示扫描量热(TG-DSC)分析、电感耦合等离子体发射光谱(ICP)和酸度滴定等对样品进行了表征。结果表明,手性Mn(salen)配合物成功固载在MCM-41上,且MCM-41的介孔结构和Mn(salen)配合物的手性特征仍然保留。以间氯过氧苯甲酸为氧化剂,考察了所得固载型催化剂对α-甲基苯乙烯的不对称环氧化催化性能,结果表明在0 ℃反应2 h,催化剂用量为0.02 mmol,无需加入轴向配体N-甲基吗啉氮氧化物(NMO)的条件下对映体过量(enantiomeric excess,e.e.)值可达99%以上,转化率为77%。归因于苄基磺酸基起到了很好的轴向配体作用。经适当处理,固载型催化剂在循环使用5次后e.e.值依然有71%,表现出较好的活性和重复使用性能。     

负极材料NiO的制备及电化学性能

以Ni(NO₃)₂·6H₂O和NaOH为原料,采用水热法合成了锂离子电池负极材料NiO。通过TG-DSC分析，确定了合成过程的反应机理。通过XRD、SEM和恒流充放电测试,研究了NiO样品的结构、形貌及电化学性能。400 ℃焙烧得到立方结构的NiO产品，以0.10 mA·cm^-2充放电,首次放电比容量达到1 151 mAh·g^-1，经过20次循环后的比容量仍为776 mAh·g^-1。     

自组装和共缩聚法制备磺酸基修饰的硅柱磷酸锆

以十六胺插层磷酸锆为原料, 利用十二烷基二甲基苄基氯化铵为导向模板剂, 通过正硅酸乙酯和巯丙基三甲氧基硅烷的层间共水解缩聚, 并结合双氧水对巯丙基的熏蒸氧化, 制备了磺酸基修饰的硅柱磷酸锆材料。通过XRD、SEM、N2吸附-脱附和FT-IR等方法对柱撑材料进行了结构表征。结果表明, 通过调变预撑剂和模板剂中的碳链长度可以优化材料的柱撑结构和孔结构, 磺酸基修饰的材料孔径分布在2.17 nm左右, 比表面积可达163 m²·g^-1, 且保留有规整有序的柱撑磷酸锆层板结构。磺酸基的修饰则成功调变了材料的酸位性质, Brönsted酸量最高可达2.71 mmol·g^-1, 总酸量可达5.20 mmol·g^-1。利用柠檬酸与正丁醇的酯化反应为探针反应, 由于磺酸基修饰的硅柱磷酸锆材料具有独特的空间反应效应和较为丰富的Brönsted酸位, 酯化反应转化率最高可达95.74%。     

双金属(Sn/Ni)掺杂多孔硅微球的液相合成与电化学储锂性能

使用廉价的硅铝合金前驱体,通过简单的化学沉积方法制备了新型双金属(Sn/Ni)掺杂多孔硅微球(pSi@SnNi)。pSi@SnNi复合材料的三维多孔结构可以缓冲硅在锂化过程中的巨大体积膨胀,增加储锂活性位点。双金属(Sn/Ni)的掺杂可以提高硅的电子导电性,改进pSi的结构稳定性。由于其独特的组成和微观结构,具有适当Sn/Ni含量的pSi@SnNi复合材料显示了较大的可逆储锂容量(0.1 A·g^-1下为2 651.7 mAh·g^-1)、较高的电化学循环稳定性(1 A·g^-1下400次循环后为1 139 mAh·g^-1)和优异的倍率性能(2.5 A·g^-1下为1 235.8 mAh·g^-1)。     

MCM-41负载S2O82-/TiO2固体超强酸的制备和酯化性能研究

采用液相沉积法制备了由MCM-41介孔分子筛负载S₂O₈^2-/TiO₂的固体超强酸催化剂。探讨了成酸机理，并以乙酸和异戊醇的酯化反应作为探针反应考察了焙烧温度、浸渍溶液浓度等制备条件对催化剂催化活性的影响，得到了较佳的制备条件。XRD、N₂吸附-脱附和FTIR结果表明，固体超强酸保持了MCM-41的介孔结构，BET表面积高达211 m²·g^-1，且具有强酸性(H_o<-12.70)。     

高比表面CexZr1-xO2复合氧化物的制备及表征

分别采用共沉淀法和阴离子表面活性剂模板法制备了Ce_xZr_1-xO₂复合氧化物。采用XRD、AFM、FTIR以及N₂吸附-脱附等方法对样品进行了表征。结果表明，共沉淀法合成的样品在500 ℃煅烧2 h后，生成了立方相Ce_0.75Zr_0.25O₂和四方相Ce_0.5Zr_0.5O₂固溶体，比表面积为62.1 m²·g^-1，孔体积为0.097 cm³·g^-1；以阴离子表面活性剂十二烷基苯磺酸钠(SDBS)为模板剂，乙二胺为助模板剂合成的样品在500 ℃煅烧2 h后，生成了纯四方相Ce_0.5Zr_0.5O₂固溶体，比表面积为180 m²·g^-1，孔体积为0.182 cm³·g^-1。结果表明，以阴离子表面活性剂SDBS为模板剂，可以合成高比表面积且具有介孔结构的Ce_0.5Zr_0.5O₂复合氧化物；加入乙二胺作为助模板剂可明显的提高比表面积和孔体积。     

双金属(Sn/Ni)掺杂多孔硅微球的液相合成与电化学储锂性能

使用廉价的硅铝合金前驱体,通过简单的化学沉积方法制备了新型双金属(Sn/Ni)掺杂多孔硅微球(pSi@SnNi)。pSi@SnNi复合材料的三维多孔结构可以缓冲硅在锂化过程中的巨大体积膨胀,增加储锂活性位点。双金属(Sn/Ni)的掺杂可以提高硅的电子导电性,改进pSi的结构稳定性。由于其独特的组成和微观结构,具有适当Sn/Ni含量的pSi@SnNi复合材料显示了较大的可逆储锂容量(0.1 A·g^-1下为2 651.7 mAh·g^-1)、较高的电化学循环稳定性(1 A·g^-1下400次循环后为1 139 mAh·g^-1)和优异的倍率性能(2.5 A·g^-1下为1 235.8 mAh·g^-1)。     

同步合成模板法制备热解炭及其电化学电容性能研究

研究制备新型炭材料是提高电化学电容器性能的有效途径。本文以二氧化硅干凝胶为模板,以合成间苯二酚-甲醛(RF)干凝胶为炭前驱体,采用同步合成模板法制得了比表面积达1100m²·g^-1,孔径分布集中,平均孔径为4.5nm的炭材料。循环伏安研究表明,与比表面积为1720m²·g^-1的活性炭相比,本研究制得的炭材料具有更优异的电化学电容性能,2mV·s^-1时比容量达195F·g^-1。     

对苯二甲酸-锌配合物孔结构的研究

以硝酸锌和对苯二甲酸为反应物,N,N′-二甲基甲酰胺(DMF)为溶剂,用溶剂热法合成出结构稳定的对苯二甲酸-锌配位化合物(MOF-L)。并采用XRD、TG、低温N₂吸附等测试手段对合成的MOF-L进行了表征。结果表明,样品的孔径分布均呈双峰型,孔结构主要由孔径小于1 nm的微孔和少量1.5～2.0 nm的超微孔组成,且小于0.7 nm的极微孔丰富;其表面在极微孔和超微孔范围存在两种吸附位。300 ℃煅烧的样品,Langmuir比表面积和单点总孔容分别为1 243 m²·g^-1和0.46 cm³·g^-1,在77 K、1.0 bar时的储氢容量为1.3wt%。400 ℃煅烧后,骨架扭曲坍塌,Langmuir比表面积、总孔容及储氢容量分别下降为1 113 m²·g^-1、0.43 cm³·g^-1和0.8wt%。     

ZnCo2O4纳米颗粒组装的毛线团状的微球用于锂离子电池负极材料

通过液相共沉淀法获得Zn和Co的前驱,经过600℃煅烧处理获得ZnCo₂O₄纳米颗粒组装的毛线团状的微球。电化学测试表明,在0.5 A·g^-1的电流密度下循环200次可逆比容量保持为965 mAh·g^-1;在0.8 A·g^-1的电流密度下循环350次可逆比容量保持为882 mAh·g^-1。倍率性能测试表明在2 A·g^-1的电流密度时可逆比容量为736 mAh·g^-1。     

半晶化双螺旋介孔MnO2的合成和电化学性质

Mesoporous silica KIT-6 has novel three-dimensional gyroidal channel structure, space group of 1a-3d, and ordered tunable pores up to 10 nm. In this paper, such mesostructured silica was employed as hard template to prepare semicrystalline gyroidal mesoporous MnO2. The structure was investigated by XRD, TEM and HRTEM, and found to be of high quality 1a-3d symmetry, in good accordance with the template structure. The material has a BET surface of 118 m2·g^-1 and pore volume of 0.35 cm3·g^- 1 after eliminating template. Mesoporous MnO2 has shown good electrochemical property as supercapacitor material in 1 mol·L^-1 Na2SO4 and 1 mol·L^-1 LiClO4 solutions, but interesting pseudocapacitance behavior was observed in the case of 6 mol·L^-1 KOH. It was found that mesoporous MnO2 performed stable reversible electrochemical behavior with capacitance of 220 F·g^-1 in a potential range of -0.1-0.55 V vs. Hg/HgO in alkaline solution, demonstrating that it is a promising novel electrode material for the fabrication of electrochemical capacitors.     

介孔分子筛MCM-48的室温合成与表面修饰

在室温条件下的碱性介质中合成了介孔分子筛MCM-48，并对其进行了有机官能团表面修饰。利用HRTEM、低温N₂吸附、XRD、TG、IR和NMR等手段对产物进行了结构和性能分析。实验结果表明，合成产物MCM-48具有规则的孔道结构、大比表面积、大孔容和窄分布的孔径。由硅烷试剂表面修饰后的MCM-48，由于有机官能团接枝在MCM-48的内表面，占据了孔道内部空间，使其比表面积、孔容和孔径都减小。     

酸法纳米纤维素模板剂合成介孔TiO2及光催化活性

以生物可再生资源的酸法纳米纤维素为模板剂,四氯化钛为钛源,采用液相水解-沉淀法制备了具有介孔结构的TiO2光催化剂。采用低温N2物理吸附-脱附、透射电镜(TEM)、X射线衍射(XRD)、热重-量热扫描(TG/DSC)、傅里叶变换红外(FTIR)、X射线光电子能谱(XPS)等对介孔TiO2进行了表征,并以甲基橙为模型物,考察了介孔TiO2光催化活性。结果表明,以酸法纳米纤维素为模板剂合成的TiO2光催化活性显著提高,且具有良好的孔隙结构,平均孔径5.03 nm、总孔容积0.35 cm3.g-1、比表面积192m2.g-1;纤维素模板剂合成的TiO2表面羟基数量降低;纤维素长链分子结构之间的羟基与TiO2表面羟基的键合,可有效限制TiO2前驱体的生长和团聚,并抑制锐钛矿相TiO2向金红石相转变。     

真空辅助硬模板法制备三维有序介孔氧化钕

以介孔氧化硅KIT-6为硬模板,硝酸钕为金属源,分别在搅拌条件和真空条件下制备具有三维介孔结构的立方多晶氧化钕。采用XRD、TEM和氮气吸附-脱附技术对所得样品进行表征。结果表明,在真空辅助条件下制备所得的氧化钕较在搅拌条件下制备得到的氧化钕具有更规则的三维有序介孔结构,两者的比表面积分别为117和84 m.2g-1。     

介孔氧化镍的复合表面活性剂模版法制备及表征

用六水合硝酸镍为镍源,尿素为沉淀剂,以少量的复合表面活性剂(SDS/P123,CTAB/P123,CTBA/SDS)为模板水热制备了介孔氧化镍。分别采用热重-差示扫描量热(TG-DSC)、傅立叶红外光谱(FTIR)、X射线衍射(XRD)、氮气吸附脱附、扫描电子显微镜(SEM)、透射电子显微镜(TEM)对产物的结构和形貌进行了表征。用循环伏安法,恒电流充放电和交流阻抗谱等对材料进行了电化学性能的测试。结果表明,以复合表面活性剂SDS/P123为模板制备的介孔氧化镍有最大的比表面积、孔径和比电容,且当SDS/P123质量比为2:1时,所制备的氧化镍比表面积、孔径和比电容分别为209 m2.g-1,0.407 cm3.g-1,265 F.g-1。     

Removal of complexed mercury by dithiocarbamate grafted on mesoporous silica

Mesoporous silica (MCM-41) with d ₍₁₀₀₎ interplanar distance of 38 Å was prepared by a room temperature process through low surfactant templation technique. The surface of MCM-41 was functionalized with dithiocarbamate (dtc) ligand, named as MCM-41-dtc and this was characterized by X-ray diffraction, BET surface area, particle size analysis, ²⁹Si MAS NMR spectra and sulphur analysis. The sorption of mercury from 0.1M HCl solution by MCM-41-dtc was studied as a function of pH, [Hg²⁺], time and temperature. The sorption data obtained at various initial concentrations of mercury were fitted into Langmuir adsorption model. Mercury speciation in solution and the sorption capacity measurements indicated possible formation of a 1 : 1 square planar complex in the solid phase. A very rapid sorption of mercury was observed in the initial stages of equilibration, which can be attributed to the large surface area, wide porosity and fine particle size of MCM-41-dtc, facilitating facile accessibility of mercury into the inner pores of the sorbent. The enthalpy change accompanied by the sorption of mercury was found to decrease from 83.7 to 6.2 kJ/mol, when the initial concentration of mercury was increased from 5^.10^-4M to 1.5^.10^-3M.     

Preparation and Characterization of Mesoporous Ce0.5Zr0.5O2 Mixed Oxide

Mesoporous （MSU） Ce0.5Zr0.5O2 mixed oxide with a high specific surface area has been synthesized under weak acidic condition in the presence of an anionic surfactant, sodium dodecylbenzenesulfonate. The effect of the pH value on the formation of mesostructure and the thermal stability of the material has been evaluated. The products were characterized by transmission electron microscopy, powder X-ray diffraction and nitrogen adsorption-desorption measurements. The results showed that the as-prepared Ce0.5Zr0.5O2 mixed oxide possessed a specific surface area of 163.3 m^2·g^-1, which had a cubic fluorite-type structure and possessed specific surface areas of 148.4 and 62.4 m^2·g^-1 after calcination at 500 and 800 ℃ for 2 h, respectively. The material showed excellent thermal stability.     

Removal of Cr(VI) from aqueous solutions using EDCC-MCM-41: Isotherm,kinetics and thermodynamic evaluation

Abstract

EDCC-MCM-41, a novel ethylenediamine derivative of MCM-41 was synthesized from a sugar industry waste, bagasse fly ash. Studies were carried out on its ability to remove Cr(VI) from aqueous solution. Its performance was also compared with that of unmodified MCM-41 and an already known derivative NH₂-MCM-41 (both also synthesized from bagasse fly ash) at the same experimental conditions. Results show that the novel adsorbent produced a better sorption performance (adsorption capacity of 49.04?mg g^?1) than MCM-41 and NH₂-MCM-41 which produced adsorption capacities of 13.78?mg g^?1 and 25.29?mg g^?1 respectively. Thermodynamics, kinetics and isotherm studies confirm that the sorption process involving the novel adsorbent is favorable for Cr(VI) and can best be represented by pseudo-second-order kinetics model. The sorption process was also found to be multistep, involving both film diffusion and intraparticle diffusion into the pores on the adsorbent’s surface.

Abbreviations: BFA: Bagasse Fly Ash; MCM-41: Mobil Composition of matter no. 41; NH2-MCM-41: mine functionalized MCM-41; EDCC-MCM-41: Ethylenediamine grafted MCM-41; qe: Mass of material adsorbed at equilibrium per mass of adsorbent; qt: Mass of material adsorbed at any time t per mass of adsorbent; C0: The initial concentration; Ce: The residual concentration at equilibrium; Ct: Residual concentration at any time t; W: The weight of adsorbents; rRMSD: Root mean square deviation; R: Gas constant     

锐钛相虫蛀状介孔二氧化钛的表征

0IntroductionMesostructuredtitania(TiO2)hasattractedagreatdealofattention,inviewofcontrolleddelivery,catalytic,photocatlytic,orenergyconversionapplica-tions犤1犦.Theuseoftitaniumisopropoxidebis-acetylace-tonateprecursors,combinedwithalkylphosphatean-ionicsurfactantsastemplate,ledtothefirstdocu-mentedpuremesoporousTiO2犤2犦.Insubsequentyears,moresyntheticstrategieshavebeendevelopedusingavarietyofstructure-directingagents,forexample,car-boxylicacids犤3犦,alkylamine犤4犦,aminium犤5犦,blockcop-o…     

A hollow porous molecularly imprinted polymer as a sorbent for the extraction of 7 macrolide antibiotics prior to their determination by HPLC-MS/MS

A hollow porous molecularly imprinted polymer (HPMIP) is described for use in dispersive solid phase extraction of macrolide antibiotics (MACs). The HPMIP was prepared by using spiramycin as the template, methacrylic acid as the functional monomer, and mesoporous MCM-41 (Mobile Composition of Matter No. 41; with a size of about 100 nm) as a sacrificial support. The sorbent was characterized by Fourier transform infrared spectrometry, transmission electron microscopy, nitrogen adsorption and thermo-gravimetric analysis. Several parameters affecting the extraction efficiency were optimized. The material has a large surface area (359 m²·g^?1), and most recognition sites are located on the surface of the HPMIPs. This results in high binding capacity (120 μmol·g^?1) and fast binding (20 min) in comparison to either MCM-41-core surface MIPs or solid MIPs. The method was applied to the extraction of the MACs azithromycin, spiramycin, tilmicosin, tylosin, clarithromycin, roxithromycin and josamycin from spiked honey. The recoveries, determined by HPLC-MS/MS, ranged from 88.0% to 117% at the three spiking levels tested (1, 5 and 20 μg·kg^?1). Intra-day and inter-day assay precision at three spiking levels are <10.7% (for n?=?6) and 12.6% (n?=?3), respectively. The limits of detection are between 3 and 17 ng·kg^?1. This indicates the superiority of the method in selective extraction of macrolides even from complex matrices.

Open image in new window

Graphical abstract Hollow porous molecularly imprinted polymers using spiramycin as the template are shown to be viable dispersive solid phase extraction adsorbents for selective enrichment of macrolide antibiotics in honey products prior to their quantitation by HPLC-MS/MS.