β-环糊精聚合物-二茂铁安培型葡萄糖氧化酶电极

利用 β-环糊精的空穴结构 ,通过主客体化学反应将二茂铁包络在 β-环糊精聚合物的空穴中 ,同时将葡萄糖氧化酶交联在 β-环糊精聚合物上 ,制成对葡萄糖有灵敏响应的生物传感器。循环伏安和安培检测表明包络在 β-环糊精聚合物空穴中的二茂铁更加接近酶的氧化还原中心 ,可以有效地作为葡萄糖氧化酶和玻碳电极之间的电子媒介体 ,葡萄糖浓度在1.0×10-2 ～8.0mmol/L范围内 ,其浓度与电流响应值呈良好的线性关系 ,方法的检出限为2.0×10-3 mmol/L(S/N=3) ,在10s之内达到最大响应的95 %。用该法测定了血清中的葡萄糖含量 ,结果与传统方法吻合。     

蒙脱石-石墨-聚氯乙烯复合电极的研制

化学修饰电极自1975年正式问世以来^[1],经过多年的不断发展,现已出现了许多修饰方法^[2];如表面吸附法,聚合物薄膜法,共价键合法等。这些方法虽在一定程度上改善了修饰电极的表面结构,提高了电极的灵敏度和选择性,但由于此类修饰都是在电极表面附上一层修饰剂,容易因修饰层不牢而脱落,或修饰厚度不均匀而影响电极的性能,近年来出现了组合法制作碳糊电极^[3]及蒙脱石修饰碳糊电极^[4]的研究,但由于碳糊及其修饰电极存在电极表面柔软的缺点而使其生理性,稳定性欠佳,本文用聚氯乙烯作粘合剂,在其融状态下,将石墨和蒙脱石混合,加压,冷却制成复合电极,该复合电极用于苯酚测定时,表现出良好的稳定性,重现性和催化效果,并克服了蒙脱石修饰碳糊电极稳定性,重现性差的缺点。     

二茂铁修饰青椒籽碳糊电极测定抗坏血酸

以二茂铁作为电子传递介体,制成Ｆｅ修饰的青椒籽碳糊电极,研究了该电极的性能,用恒电位电流法测定了抗坏血酸的浓度并用于药物中抗坏血酸的含量分析,结果与药典法相符。     

自组装单层界面β-环糊精非电活性客体的电化学测定

提出了用电化学技术测定非电活性物质的新方法.利用合成的β-CD对甲苯磺酸基衍生物(Ts-β-CD)获得新型β-CD单层.虽然β-CD的覆盖率只有10%左右,但该单层对二茂铁表现出有效的主客体响应.界面上二茂铁的包络符合Langmuir吸附响应.利用Langmuir吸附等温式,得到二茂铁与β-环糊精形成包络物的包络常数为4.2×10~4mol-1·L二茂铁在该单层上的最大表面覆盖度为8.6×10~(-12)mol/cm2.当二茂铁溶液中含有非电活性物质间甲苯甲酸(mTA)或十二烷基磺酸钠(SDS)时,mTA和SDS与包络在电极表面的二茂铁发生客体竞争反应而使二茂铁的氧化还原峰电流降低.利用该原理,分别测定了非电活性物质mTA和SDS,线性范围分别为0.8~2.7μmol/L和5~100nmol/L.     

基于纳米MnO_2二茂铁修饰丝网印刷碳电极的尿酸生物传感器研究

在丝网印刷碳电极上修饰纳米MnO2,并利用戊二醛和β-环糊精交联固定尿酸酶,以二茂铁作为电子媒介体,研制用于测定尿酸浓度的生物传感器.实验结果表明,纳米MnO2降低了电子媒介体二茂铁的氧化还原反应电位,且纳米MnO2与电子媒介体二茂铁在尿酸生物传感器中表现出协同增效效应.该尿酸生物传感器线性响应范围是6.0×10-6～1.2×10-3 mol/L,检出限为3.0×10-6 mol/L.用纳米MnO2修饰酶电极,改善了电极表面条件,加快了电极反应速率,提高了尿酸传感器的灵敏度.     

β-环糊精与二茂铁包合物修饰碳糊电极上抗坏血酸的催化氧化波研究

二茂铁及其衍生物不能牢固吸附于电极表面, 特别是其氧化态(Fc+)溶于水, 影响了电极的稳定性[1].     

抗坏血酸在β-环糊精/二茂铁甲酸修饰电极上的电化学行为及测定

利用主客体化学反应将二茂铁甲酸包络在β-环糊精聚合物的空穴中,用新鲜蛋清作交联剂制成β-环糊精聚合物/二茂铁甲酸化学修饰玻碳电极,用电化学阻抗法和循环伏安法研究了修饰电极的电化学性能。在pH 7.0的磷酸盐缓冲溶液中,该修饰电极对抗坏血酸的电化学氧化有很好的催化活性,氧化峰电流与其浓度在6.2×10-6~5.0×10-3mol/L范围内呈良好的线性关系,线性回归方程为ip=0.4375+0.0301C(ip:μA,C:μmol/L),相关系数r=0.9982,检出限为1.0×10-6mol/L。抗坏血酸和多巴胺在修饰电极上于不同的电位(ΔE=490 mV)被氧化,可用于多巴胺存在下选择性测定抗坏血酸。     

多金属氧簇阴离子[Mo6O19]2-/PAMAM超分子化合物的制备、表征及性能

采用树状聚酰胺-胺(PAMAM)大分子化合物与同多酸阴离子[Mo6O19]2-,基于静电作用合成了同多金属氧酸盐/树型分子超分子化合物。用元素分析、FTIR、UV-V is、TG/DTA、荧光光谱等测试技术分别对样品进行了结构表征及性能测试。并利用其作为电极修饰剂,制得化学体修饰的碳糊电极(CMCPE),用循环伏安法研究了同多金属氧酸盐/树型分子超分子化合物修饰碳糊电极在1 mol/L H2SO4水溶液中的电化学行为。结果表明,该化合物具有良好的荧光性能和可逆光致变色性能;用该化合物修饰的碳糊电极与[Mo6O19][N(C4H9)2]2修饰的电极相比,在-0.2~0.2 V范围内多了1对氧化还原峰;当扫描速率低于100 mV/s时,该电极过程为表面控制过程,而当扫描速率高于100 mV/s时,电极过程变为扩散控制过程;且该电极在室温下具有很好的稳定性。     

水溶液中几种苯衍生物与β-环糊精包合物的热力学研究

β 环糊精 (β Ｃｙｃｌｏｄｅｘｔｒｉｎ ,β ＣＤ)是由 7个葡萄糖残基以α 1 ,4 糖苷键连接而成的环状化合物 ,具有疏水的空腔和亲水的外表面。这种特殊的结构使它可以作为宿主 (主体 )而依疏水作用力、范德华力或氢键包合多种客体分子形成包合物[1～ 3] ,并可增强客体分子对光、热、氧化等的稳定性[4,5] 。有机物质与 β ＣＤ形成包合物后通常会发生光谱等特征的变化 ,因此可用光谱等方法研究包合物的稳定常数[4] ,并进而获得水溶液中包合体系的热力学参数[6 ] 。本文采用紫外分光光度法 ,研究水溶液中几种苯衍生物与β ＣＤ包合物的稳定…     

5,11,17,23-四叔丁基-25,26,27,28-四[3-(甲氧基羰基)苄氧基]杯[4]芳烃包合性能的研究

杯芳烃是继冠醚和环糊精后的第三代主体化合物 .这类主体分子不仅可以识别和络合阳离子 ,而且还具有包合中性有机分子的性能 [1～ 5] .杯 [4]芳烃类包合物的晶体结构测定表明 ,它们可分为分子内和分子间包合两种类型 [3 ,5] ,前者是客体分子被包合在主体分子的空穴内 ,后者是客体分子被包合在主体分子之间 .对叔丁基杯 [4]芳烃的下沿酚氧基与上沿均可进行化学修饰得到不同的杯 [4]芳烃衍生物 .最早报道的对叔丁基杯 [4]芳烃及其衍生物的分子内包合物是与甲苯或乙腈的 1∶ 1包合物 [4 ,5] ,客体分子依靠 CH3 -π的作用被包结在主体分子内[6]…     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

Cu0-catalysed 1,3-dipolar cycloadditions of α-amino acid derived N,N-cyclic azomethine imines to ynones

A series of 20 CuAIAC reactions between eight 4-acylamino substituted pyrazolidine-3-one-1-azomethine imines and four terminal ynones were performed using Cu⁰ as catalyst. The corresponding fluorescent cycloadducts were obtained in very high yields upon simple workup. Thus, Cu-metal turned out to be a better catalyst than Cu^I in terms of yield and ease of isolation. Availability of azomethine imines, mild reaction conditions, and simple workup enable a “click” access to libraries of densely substituted 2,3-dihydro-1H,5H-pyrazolo[1,2-a]pyrazol-1-ones. Reactivity of differently substituted dipoles was evaluated experimentally and by quantum chemical methods (DFT).     

Synthesis and antioxidative/anti-inflammatory activity of novel fullerene–polyamine conjugates

(E)-4-(Fullerenopyrrolidin-1-yl)-3-methylbut-2-enoic acid and its corresponding succinimidyl ester, readily obtained through Prato-type modification of C₆₀, were used for the selective N-acylation of polyamines. The thus obtained conjugates were evaluated for their antioxidative and anti-inflammatory activity and their cytotoxicity was determined. Members of this family of compounds showed interesting anti-lipid peroxidation, anti-lipoxygenase and anti-inflammatory activity and comparable cytocompatibility to spermidine.     

Copper-catalyzed multicomponent reactions of 2-iodoanilines,benzylamines, and elemental sulfur toward 2-arylbenzothiazoles

A relatively cheap copper salt-catalyzed, three-component approach providing 2-arylbenzothiazoles in good to excellent yields from readily available 2-iodoanilines, benzylamines, and sulfur powder is reported. This methodology allows preparation of various classes of 2-arylbenzothiazoles and provides a general, reliable approach.