Pt/C和Pt/CNTs电极的电化学稳定性研究

采用恒电位氧化法研究了Pt/C和Pt/CNTs电极的电化学稳定性. 相同条件下, Pt/C电极的氧化电流大约为Pt/CNTs电极的2倍; 120 h氧化后, Pt/C电极Pt的电化学表面积下降了21.3%, 而Pt/CNTs电极仅下降了7.6%, 表明Pt/CNTs电极性能衰减较慢. X射线光电子能谱(XPS)分析表明, Pt/C的载体碳黑表面氧增加量大于Pt/CNTs中碳纳米管(CNTs)表面氧的增加量, 说明碳黑的被氧化程度较高, 电化学稳定性差; Pt的表面化学状态没有发生变化; 碳纳米管本身的抗电化学氧化性也大于碳黑. 所以, 载体的被氧化程度不同是两种电极性能衰减不同的主要原因之一, 并且排除了Pt表面状态的影响.     

不同直径碳纳米管的抗电化学氧化性

本文比较了由化学气相沉积法制备的不同直径(在100 nm以内)的多壁碳纳米管(CNT)的抗电化学氧化性.将CNT电极于1.2 V(vs.RHE)下电氧化120 h,记录氧化电流~时间变化曲线;X射线光电子能谱(XPS)分析氧化前后CNT的表面化学组成.结果表明,随着CNT直径的减小,其氧化电流降低,但其中以为10~20 nm的CNT电极氧化电流最小,表面氧的增量也最小,即被氧化的程度最低,抗电化学氧化性最强.根据不同直径CNT的缺陷位、不定型碳的丰度和碳原子的应力能,分析了其抗电化学氧化性差异的原因.     

碳纳米管电极上原位沉积Pt纳米颗粒

 本文利用原位离子交换法制备了碳纳米管(CNTs)载铂(Pt/CNTs)电极. X射线光电子能谱分析表明, Pt通过离子交换载于电化学功能化的CNTs表面. 扫描电镜照片显示, Pt高度分散于CNTs表面. X射线衍射分析表明, Pt的粒径约为4.0 nm. 离子交换法所制Pt/CNTs电极的电化学表面积和Pt的利用率均大于传统Pt/CNTs电极(Pt粒径约为2.5 nm), 其对氧还原的催化活性高于传统电极. 这归因于离子交换法所制电极的特殊结构,即Pt普遍载于电化学活性位上.     

基于镍/氮掺杂碳复合材料的双功能电催化剂合成及电化学性能研究

通过高温热解氢氧化镍/聚苯胺前驱体,制备了镍/氮掺杂碳复合材料,并作为双功能电催化剂应用于可充电锌-空气电池。利用X射线衍射、透射电镜、拉曼光谱、X射线光电子能谱等对样品的形貌与结构进行表征,并利用电化学工作站与旋转圆盘电极对样品的氧还原与氧析出电催化性能进行测试。线性扫描伏安曲线的结果表明,在0.1 M KOH水溶液中氧还原起始电位与半波电位分别为0.894 V和0.833 V vs.RHE,接近商业Pt/C。氧析出过电位在电流密度为10 mA·cm^-2时为0.356 V vs.RHE,略优于RuO₂。     

乙醇在Pt/nanoTiO2-CNT复合催化剂上的电催化氧化

通过前驱体Ti(OEt)4直接水解和电化学扫描电沉积法制备在Ti基体上的纳米TiO2-碳纳米管复合膜载Pt(Pt/nanoTiO2-CNT)复合催化剂. 透射电镜 (TEM) 和X射线衍射 (XRD) 结果表明, 锐钛矿型纳米TiO2粒子和Pt纳米粒子(粒径均为5~10 nm)均匀地分散在碳纳米管表面. 通过循环伏安和计时电流法研究表明, Pt/nanoTiO2-CNT 复合催化剂(Pt载量为0.32 mg•cm−2) 具有高达51.8 m2•g−1的电化学活性比表面积, 常温常压下对乙醇的电化学氧化具有高催化活性和稳定性, 乙醇氧化峰电位分别为0.59、0.96和0.24 V, 氧化峰电流密度分别达到−115、−113和−75 mA•cm−2. 复合催化剂对乙醇电氧化的高催化活性可归因于nanoTiO2、CNT和Pt纳米粒子的协同催化作用.     

氮掺杂碳纳米管负载Co3O4氧还原电催化剂的制备与性能

以碳纳米管(CNT)为原料,通过负载维生素B₁₂,简单热解得到了一种氮掺杂碳纳米管(N/CNT)负载低含量Co₃O₄纳米颗粒的氧还原电催化剂(Co₃O₄@N/CNT)。得益于均匀分散的Co₃O₄纳米颗粒以及氮掺杂,Co₃O₄@N/CNT表现出了优异的氧还原催化性能,其半波电位达到了0.844 V(vs RHE),超越了商业Pt/C(0.820 V(vs RHE))。与Pt/C相比,基于Co₃O₄@N/CNT组装的锌-空气电池表现出了更优的放电性能和循环稳定性。     

氮掺杂碳纳米管负载Co3O4氧还原电催化剂的制备与性能

以碳纳米管(CNT)为原料,通过负载维生素B₁₂,简单热解得到了一种氮掺杂碳纳米管(N/CNT)负载低含量Co₃O₄纳米颗粒的氧还原电催化剂(Co₃O₄@N/CNT)。得益于均匀分散的Co₃O₄纳米颗粒以及氮掺杂,Co₃O₄@N/CNT表现出了优异的氧还原催化性能,其半波电位达到了0.844 V (vs RHE),超越了商业Pt/C (0.820 V (vs RHE))。与Pt/C相比,基于Co₃O₄@N/CNT组装的锌-空气电池表现出了更优的放电性能和循环稳定性。     

交替微波加热法对制备氧还原催化剂性能的影响

详细研究了交替微波加热法制备多壁碳纳米管负载Pt催化剂(Pt/MWCNTs)的过程中交替微波加热(5s-on/5s-off)次数对催化剂性能的影响.X射线粉末衍射(XRD)结果表明,Pt的晶粒尺寸在开始的加热阶段基本上没有发生变化,但是随着加热次数的增多,Pt的晶粒尺寸逐步增大.采用循环伏安法和旋转圆盘电极技术考察了催化剂的电化学活性.结果显示,以5s-on/5s-off加热20次时,催化剂显示出最佳的催化活性;在0.5mol· L-1 H2SO4饱和氧水溶液中催化剂的氧还原起峰电位接近1.0 V(vs RHE).交替微波加热法简单经济,在大批量制备催化剂等纳米材料方面显示出较好的应用前景.     

以切短多壁碳纳米管为载体制备高活性Pt/SCNT及PtRu/SCNT燃料电池催化剂

采用乙醇为助磨剂,利用球磨的方法将5-15μm长的多壁碳纳米管切短成长度约为200nm,并且分布较为均匀的短碳纳米管(SCNT).以SCNT为载体,采用有机溶胶法制得了含铂20%(w)的Pt/SCNT及PtRu/SCNT催化剂.实验发现:对于甲醇的阳极电氧化过程,以切短碳纳米管为载体的Pt/SCNT催化剂具有比相同条件制得的Pt/CNT催化剂高得多的催化活性,前者甲醇氧化峰电流密度是后者的1.4倍,并且远远高于商品的Pt/C催化剂.同时我们发现添加了钌的PtRu/SCNT具有比不含钌的催化剂更好的活性.采用X射线衍射(XRD)、透射电镜(TEM)、比表面积分析(BET)等方法对催化剂进行表征,结果表明,切短碳纳米管的晶相结构并未改变,但Pt/SCNT和PtRu/SCNT催化剂的比表面积和电化学活性得到了显著的提高.     

碳纳米管负载铂颗粒酶电极葡萄糖传感器

以碳纳米管负载纳米铂颗粒修饰玻碳电极 (CNT Pt/GCE)为基底 ,用明胶固定葡萄糖氧化酶(GOD) ,构建了电流型葡萄糖生物传感器 (GOD/CNT Pt/GCE)。在实验中 ,GOD/CNT Pt/GCE显示了良好的分析性能 ,与常规铂电极葡萄糖传感器 (GOD/Pt)相比较 ,测定葡萄糖的检出限从 6 .7× 10 -3 mol/L下降到8.3× 10 -4mol/L ;工作电位从 0 .6 5V下降至 0 .4 5V ;响应时间从 30s下降至 5s左右。实验结果表明 ,具有高度电催化活性的CNT Pt/GCE可作为酶传感器的一种新型基体电极。     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

Cu0-catalysed 1,3-dipolar cycloadditions of α-amino acid derived N,N-cyclic azomethine imines to ynones

A series of 20 CuAIAC reactions between eight 4-acylamino substituted pyrazolidine-3-one-1-azomethine imines and four terminal ynones were performed using Cu⁰ as catalyst. The corresponding fluorescent cycloadducts were obtained in very high yields upon simple workup. Thus, Cu-metal turned out to be a better catalyst than Cu^I in terms of yield and ease of isolation. Availability of azomethine imines, mild reaction conditions, and simple workup enable a “click” access to libraries of densely substituted 2,3-dihydro-1H,5H-pyrazolo[1,2-a]pyrazol-1-ones. Reactivity of differently substituted dipoles was evaluated experimentally and by quantum chemical methods (DFT).     

Synthesis and antioxidative/anti-inflammatory activity of novel fullerene–polyamine conjugates

(E)-4-(Fullerenopyrrolidin-1-yl)-3-methylbut-2-enoic acid and its corresponding succinimidyl ester, readily obtained through Prato-type modification of C₆₀, were used for the selective N-acylation of polyamines. The thus obtained conjugates were evaluated for their antioxidative and anti-inflammatory activity and their cytotoxicity was determined. Members of this family of compounds showed interesting anti-lipid peroxidation, anti-lipoxygenase and anti-inflammatory activity and comparable cytocompatibility to spermidine.     

Copper-catalyzed multicomponent reactions of 2-iodoanilines,benzylamines, and elemental sulfur toward 2-arylbenzothiazoles

A relatively cheap copper salt-catalyzed, three-component approach providing 2-arylbenzothiazoles in good to excellent yields from readily available 2-iodoanilines, benzylamines, and sulfur powder is reported. This methodology allows preparation of various classes of 2-arylbenzothiazoles and provides a general, reliable approach.