首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到10条相似文献,搜索用时 93 毫秒
1.
Modeling study is performed to reveal the special features of the entrainment of ambient air into subsonic laminar and turbulent argon plasma jets. Two different types of jet flows are considered, i.e., the argon plasma jet is impinging normally upon a flat substrate located in atmospheric air surroundings or is freely issuing into the ambient air. It is found that the existence of the substrate not only changes the plasma temperature, velocity and species concentration distributions in the near-substrate region, but also significantly enhances the mass flow rate of the ambient air entrained into the jet due to the additional contribution to the gas entrainment of the wall jet formed along the substrate surface. The fraction of the additional entrainment of the wall jet in the total entrained-air flow rate is especially high for the laminar impinging plasma jet and for the case with shorter substrate standoff distances. Similarly to the case of cold-gas free jets, the maximum mass flow-rate of ambient gas entrained into the turbulent impinging or free plasma jet is approximately directly proportional to the mass flow rate at the jet inlet. The maximum mass flow-rate of ambient gas entrained into the laminar impinging plasma jet slightly increases with increasing jet-inlet velocity but decreases with increasing jet-inlet temperature.  相似文献   

2.
Modeling results are presented to compare the characteristics of laminar and turbulent argon thermal plasma jets issuing into ambient air. The combined-diffusion-coefficient method and the turbulence-enhanced combined-diffusion-coefficient method are employed to treat the diffusion of ambient air into the laminar and turbulent argon plasma jects, respectively. It is shown that since only the molecular diffusion mechanism is involved in the laminar plasma jet, the mass flow rate of ambient air entrained into the laminar plasma jet is comparatively small and less dependent on the jet inlet velocity. On the other hand, since turbulent transport mechanism is dominant in the turbulent plasma jet, the entrainment rate of ambient air into the turbulent plasma jet is about one order of magnitude larger and almost directly proportional to the jet inlet velocity. As a result, the characteristics of laminar plasma jets are quite different from those of turbulent plasma jets. The length of the high-temperature region of the laminar plasma jet is much longer and increases notably with increasing jet inlet velocity or inlet temperature, while the length of the high-temperature region of the turbulent plasma jet is short and less influenced by the jet inlet velocity or inlet temperature. The predicted results are reasonably consistent with available experimental observation by using a DC arc plasma torch at arc currents 80–250 A and argon flow rates (1.8–7.0)×10−4 kg/s.  相似文献   

3.
Modeling study is performed to reveal the momentum and heat/mass transfer characteristics of a turbulent or laminar plasma reactor consisting of an argon plasma jet issuing into ambient air and interacting with a co-axially counter-injected argon jet. The combined-diffusion-coefficient method and the turbulence-enhanced combined-diffusion-coefficient method are employed to treat the diffusion of argon in the argon–air mixture for the laminar and the turbulent regimes, respectively. Modeling results presented include the streamline, isotherm and argon mass fraction distributions for the cases with different jet-inlet parameters and different distances between the counter-injected jet exit and the plasma torch exit. It is shown that there exists a quench layer with steep temperature gradients inside the reactor; a great amount of ambient air is always entrained into the plasma reactor; and the flow direction of the entrained air, the location and shape of the quench layer are dependent on the momentum flux ratio of the plasma jet to the counter-injected cold gas. Two quite different flow patterns are obtained at higher and lower momentum flux ratios, and thus there exists a critical momentum flux ratio to separate the different flow patterns and to obtain the widest quench layer. There exists a high argon concentration or even ‘air-free’ channel along the reactor axis. No appreciable difference is found between the turbulent and laminar plasma reactors in their overall plasma parameter distributions and the quench layer locations, but the values of the critical momentum flux ratio are somewhat different.  相似文献   

4.
When materials processing is conducted in air surroundings by use of an impinging plasma jet, the ambient air will be entrained into the materials processing region, resulting in unfavorable oxidation of the feedstock metal particles injected into the plasma jet and of metallic substrate material. Using a cylindrical solid shield may avoid the air entrainment if the shield length is suitably selected and this approach has the merit that expensive vacuum chamber and its pumping system are not needed. Modeling study is thus conducted to reveal how the length of the cylindrical solid shield affects the ambient air entrainment when materials processing (spraying, remelting, hardening, etc.) is conducted by use of a turbulent or laminar argon plasma jet impinging normally upon a flat substrate in atmospheric air. It is shown that the mass flow rate of the ambient air entrained into the impinging plasma jet cannot be appreciably reduced unless the cylindrical shield is long enough. In order to completely avoid the air entrainment, the gap between the downstream-end section of the cylindrical solid shield and the substrate surface must be carefully selected, and the suitable size of the gap for the turbulent plasma jet is appreciably larger than that for the laminar one. The overheating of the solid shield or the substrate could become a problem for the turbulent case, and thus additional cooling measure may be needed when the entrainment of ambient air into the turbulent impinging plasma jet is to be completely avoided.  相似文献   

5.
An experimental study is conducted to investigate the entrainment characteristics of a turbulent thermal plasma jet issuing from a DC arc plasma torch operating at atmospheric pressure. The mass flow rate of the ambient gas entrained into the turbulent plasma jet is directly measured by use of the so-called “porous-wall chamber” technique. It is shown that a large amount of ambient gas is entrained into the turbulent plasma jet. With the increase of the gas mass flow rate at the plasma jet inlet or the plasma torch exit, the mass flow rate of entrained ambient gas almost linearly increases but its ratio to the jet-inlet mass flow rate decreases. The mass flow rate of the entrained gas increases with the increase of the arc current or jet length. It is also found that using different ways to inject the plasma-forming gas into the plasma torch affects the entrainment rate of the turbulent plasma jet. The entrainment rate expression established previously by Ricou and Spalding (J. Fluid Mech. 11: 21, 1961) for the turbulent isothermal jets has been used to correlate the experimental data of the entrainment rates of the turbulent thermal plasma jet, and the entrainment coefficient in the entrainment rate expression is found to be in range from 0.40 to 0.47 for the turbulent thermal plasma jet under study.  相似文献   

6.
Measurements of composition, temperature, and velocity in atmospheric argon plasma jets are reported, using enthalpy probes. The plasma jets are generated by a commercial type plasma gun and the measurements are expected to be of particular interest for industrial applications such as plasma spraying. Emphasis has been on the central and downstream regions of the plasma flame. The entrainment of air into the jet was found to be very high, even close to the axis of the jet. Gas samples analyzed with a gas chromatograph showed demixing of the air, i.e., nitrogen is more abundant in the jet than at room temperature. The high air entrainment has a strong cooling effect on the plasma, resulting in a rapid temperature drop along the axis. The influence of the argon flow rate and of the arc current on the jet's conditions was parametrically studied. Matching of the quantities measured in the jet with the torch input confirmed the validity of the results, and the relevance of enthalpy probe diagnostics in thermal plasma jets.  相似文献   

7.
This paper attempts to predict the noise emission characteristics of a turbulent argon thermal-plasma jet issuing into ambient air. The flow, temperature and concentration fields and turbulence characteristics of the turbulent plasma jet are computed at first, and then the noise emission from the plasma jet to a sideline far-field observer is calculated using the approach proposed by Fortuné and Gervais (AIAA J. 37(1999)1055) for predicting the noise emission from a turbulent, hot but non-ionized, air jet after some modification. The diffusion of ambient air into the turbulent argon plasma jet is handled using the turbulence-enhanced combined–diffusion-coefficient method. Velocity fluctuation correlations (aerodynamic noise source) in the plasma jet are calculated still using the K-ɛ two-equation turbulence model, but the temperature-velocity fluctuation correlations (entropic noise source) within the jet are calculated by solving a second-order turbulent Reynolds heat-flux transport equation in order to better deal with the contribution of temperature fluctuation to the noise emission. It is shown that among the contributions of aerodynamic noise source, entropic noise source and their mixed effect, the entropic noise source (i.e. the temperature-velocity fluctuation correlations) is dominant for the noise emission from the turbulent plasma jet to the sideline observer. The noise intensity increases with increasing plasma jet temperature or velocity. The predicted noise frequency spectrum characteristics and noise intensity levels are shown to be reasonably consistent with available experimental data.  相似文献   

8.
Improvement of plasma spraying efficiency and coating quality   总被引:1,自引:1,他引:0  
A commercial torch has been modified to introduce an additional anti-vortex and shroud gas flow to counter the detrimental effects brought about by the vortex plasma gas flow which is used to stabilize the cathode arc attachment and to increase the anode life. Deposition efficiency and coating quality are used as criteria to judge the modified versus the nonmodified torch. High-speed videography and computerized image analysis systems are used to determine the particle trajectories, velocities, and the plasma jet geometry. The results show that the additional anti-vortex and shroud gas flow to the torch can keep the particles closer to the torch axis and reduce the amount of entrainment of cold air into the plasma jet. The consequence is that deposition efficiency and coating quality are substantially improved.  相似文献   

9.
The generation, jet length and flow-regime change characteristics of argon plasma issuing into ambient air have been experimentally examined. Different torch structures have been used in the tests. Laminar plasma jets can be generated within a rather wide range of working-gas flow rates, and an unsteady transitional flow state exists between the laminar and turbulent flow regimes. The high-temperature region length of the laminar plasma jet can be over an order longer than that of the turbulent plasma jet and increases with increasing argon flow rate or arc current, while the jet length of the turbulent plasma is less influenced by the generating parameters. The flow field of the plasma jet has very high radial gradients of plasma parameters, and a Reynolds number alone calculated in the ordinary manner may not adequately serve as a criterion for transition. The laminar plasma jet can have a higher velocity than that of an unsteady or turbulent jet. The long laminar plasma jet has good stiffness to withstand the impact of laterally injected cold gas and particulate matter. It could be used as a rather ideal object for fundamental studies and be applied to novel materials processing due to its attractive stable and adjustable properties.  相似文献   

10.
Long, laminar plasma jets at atmospheric pressure of pure argon and a mixture of argon and nitrogen with jet length up to 45 times its diameter could be generated with a DC arc torch by restricting the movement of arc root in the torch channel. Effects of torch structure, gas feeding, and characteristics of power supply on the length of plasma jets were experimentally examined. Plasma jets of considerable length and excellent stability could be obtained by regulating the generating parameters, including arc channel geometry, gas flow rate, and feeding methods, etc. Influence of flow turbulence at the torch nozzle exit on the temperature distribution of plasma jets was numerically simulated. The analysis indicated that laminar flow plasma with very low initial turbulent kinetic energy will produce a long jet with low axial temperature gradient. This kind of long laminar plasma jet could greatly improve the controllability for materials processing, compared with a short turbulent arc jet.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号