负载型Sn2(OMe)4/SiO2催化剂的制备及其催化CO2和CH3OH直接合成碳酸二甲酯的性能

 采用表面改性法制备了负载型Sn2（OMe）4／SiO2双核桥联配合物催化剂，用IR，TPD和微反技术对催化剂的表面结构、化学吸附性质和催化活性进行了研究．结果表明，双核桥联Sn2（OMe）4／SiO2配合物中存在Sn－O－Si双齿配位形式，甲氧基以桥基形式联结两个Sn4＋离子；CO2在催化剂表面以桥式吸附态和甲氧碳酸酯基吸附态存在，而CH3OH只以分子吸附态存在．在反应温度413K，压力0．5MPa，反应空速1500h－1以及CH3OH与CO2的摩尔比为2～2．5的反应条件下，CO2和CH3OH在Sn2（OMe）4／SiO2催化剂上生成碳酸二甲酯的选择性达到近100％．根据实验结果，提出了CO2与CH3OH在Sn2（OMe）4／SiO2催化剂表面上的反应机理，反应物分子共吸附于催化剂表面同一活性位上及CO2的甲氧碳酸酯基吸附态的形成是反应顺利进行的关键因素．     

K2O助剂对合成碳酸二甲酯用Cu/Ni/ZrO2-SiO2催化剂的吸附和催化性能的影响

 用等体积浸渍法制备了ZrO2－SiO2（ZrSiO）表面复合氧化物负载的Cu－Ni催化剂,并用IR,TPR,TPD及微反技术考察了K2O助剂对CO2和CH3OH在Cu－Ni／ZrSiO催化剂表面上的吸附及合成碳酸二甲酯（DMC）反应性能的影响．结果表明：加入K2O助剂使CO2在催化剂表面上的吸附增强,当n（K）／n（Cu＋Ni）＝15％时,CO2在催化剂表面上吸附后生成K2CO3;CH3OH在催化剂表面上的解离吸附态（CH3O－和H＋）的吸附减弱;CO2和CH3OH在Cu－Ni／ZrSiO催化剂表面上反应的主要产物为DMC,H2O,CO和CH2O;随着K2O助剂的加入,反应转化率及DMC选择性提高,副产物（CO和CH2O）的选择性下降．根据实验结果,探讨了K2O对催化剂表面活性中心电荷分布的影响．     

不同方法制备的Ni／ZrO2-CeO2-Al2O3催化剂对CH4-CO2重整反应的催化性能

 采用水热合成法、溶胶凝胶法和共沉淀－负载法制备了相同NiO含量的Ni／ZrO2－CeO2－Al2O3催化剂，考察了它们在CH4－CO2重整反应中的催化性能及稳定性，测定了积碳量．用CO2程序升温脱附方法测试了它们的CO2吸附性能，用H2程序升温脱附方法测试了表面Ni的分散度．结果表明，随温度升高，CH4和CO2转化率降低的顺序是：溶胶凝胶法≈共沉淀－负载法＞水热合成法，并且反应产物中n（CO）／n（H2）比随温度升高而降低．水热法和共沉淀－负载法制备的催化剂稳定性好，且前者的活性比后者高；溶胶凝胶法制得的催化剂活性较高，但易失活．积碳量大小顺序是：水热法＞溶胶凝胶法＞共沉淀－负载法．与其他方法制备的催化剂相比，水热法制备的催化剂对CO2的吸附量更大，\r\n而且积碳主要存在于载体上，从而保证了催化剂的稳定性．     

等离子体协同CuO／TiO2-γ·Al2O3催化CH4脱除NO

对合成的12％CuO／15％TiO2／γ-Al2O3催化剂进行了BET和XRD表征,并结合等离子体与催化协同脱除NO的反应装置,考察了单一等离子体、单一催化剂以及等离子体与催化协同脱除NO＋CH4＋O2的反应结果,研究了上述三种条件下NO和CH4的转化率。BET表征结果表明,15％TiO2／γ-Al2O3的孔径分布在微孔和介孔之间;XRD结果表明,催化剂表面有CuO晶相;反应活性数据表明,单一等离子体存在时,NO和CH4的转化率随着等离子体的输入功率增大而逐渐增加,反应体系引入体积分数为2．5％的O2气促进了NO和CH4的转化;使用单一催化剂时,NO和CH4的转化率随温度升高而分别增大至30％和20％。同时NO转化率随O2气浓度的增加先增加后降低,CH4随O2气浓度的增加转化率逐渐增大;等离子体与催化剂协同作用NO＋CH4＋O2反应中,NO和CH4的转化率随O2气浓度的增加与只有催化剂存在条件下的变化趋势一致,但是增大了NO的低温转化率,同时CH4的转化率提高到了90％。     

Mo2C/Al2O3催化剂用于甲烷部分氧化(POM)制合成气的研究

制备了一系列不同Mo2C担载量的Mo2C／A1203催化剂，利用微型固定床反应器对其POM反应进行了活性评价，并采用XRD、SEM和BET等方法进行了结构表征．实验结果表明，纯Mo2C催化剂在反应初期有较高的CH4转化率，但CO和H2的选择性很低，随着反应时间的增加，CH4转化率急剧下降．Mo2C担载量小于24．8％的催化剂，随担载量增加，CH4转化率明显升高．同时，随着反应时间的增加，CH4转化率有所下降，CO和H2的选择性则明显升高．Mo2C担载量在35．4％—42．5％的催化剂，具有好的CH4转化率和CO、H2选择性，但担载量过高时，CH4转化率会随反应时间的增加而下降．结构表征表明，未担载的和担载的碳化物催化剂均为β-Mo2C，担载量小于10．6％时，Mo2C高度分散于A12O3表面，担载量较高时，Mo2C颗粒变大，比表面减小．     

硒催化下CO/H2O还原硝基苯制苯胺

 采用硒作催化剂，不使用任何助催化剂，用CO／H2O对硝基苯进行还原得到了苯胺．考察了反应时间、CO压力、反应温度、水量、硒粉用量和溶剂等因素对反应的影响．以四氢呋喃作溶剂，在n（H2O）／n（PhNO2）＝10，n（Se）／n（PhNO2）＝0．02，p（CO）＝4MPa，θ＝160℃，t＝3h时，硝基苯转化率可达到98．2％，生成苯胺的选择性为100％．     

Fe－Mn催化剂对F－T合成反应的催化性能Ⅱ．中后期反应性能

 采用固定床积分反应器，详细考察了F－T合成反应用Fe－Mn催化剂运行900和1800h后的中后期反应性能．结果表明，该催化剂仍维持着较高的催化活性及稳定性；与初期反应性能相比，运行900h后CH4选择性有明显升高的趋势，运行1800h后CH4选择性进一步升高．运行2200h后，通过降低原料气的H2／CO比和提高反应压力，可明显改善烃产物的选择性．在n（H2）／n（CO）＝0．62，GHSV＝2300h－1，p＝3．02MPa和θ＝283℃的条件下，CO转化率可达75．6％，总有效烃（C＝2～4＋C＋5）的选择性可达89．0％，CH4选择性为5．7％．这表明该催化剂具有良好的可操作性，且特别适合于由煤制合成气制液体燃料和C2～4低碳烯烃，在浆态床反应器中有潜在的应用前景．     

反应条件对Mo2C/Al2O3催化的POM制合成气的影响

考察了反应温度、气体空速和进料中CH4：O2比值对Mo2C／Al2O3催化的POM反应制合成气的影响．结果发现较高的温度具有较高的甲烷转化率、CO和H2的选择性；而在较低的温度下，对CO的选择性比对H2的影响更大．反应气体的空速较小时对于甲烷的转化率、CO和H2的选择性是有利的；而在较高的气体空速下，氢气的选择性则更低．进料中CH4：O2比值稍高于2：1时有利于获得高的甲烷转化率、CO和H2的选择性．并且还可以增加催化剂的稳定性．当CH4：O2比值低于2：1时．甲烷转化率、CO和H2选择性随反应的进行急剧下降．而当此比值调整到高于2：1时．转化率和选择件都可以得到恢复。     

NOx催化的甲烷气相氧化反应

 考察了没有固体催化剂时NOx对甲烷气相氧化的催化作用，并用原位红外光谱研究了CH4－O2－NOx体系随温度的变化．实验结果表明，NOx对甲烷气相氧化有很高的催化活性．在20％CH4－10％O2体系中加入0．05％～0．2％的NO后，反应温度可降低200～300℃，在650～700℃下反应时，CH4转化率和CO选择性可分别达到38％和90％，产物中的n（H2）／n（CO）比为0．4～0．7．反应产物中可观察到有甲醛、甲醇和乙烯等，通过改变反应条件可以控制各组分的相对浓度．     

纳米Cr2O3系列催化剂上CO2氧化乙烷脱氢制乙烯反应

 采用溶胶－凝胶法和共沸蒸馏法耦合技术制备了纳米Cr2O3催化剂，并采用共沉淀法和共沸蒸馏法耦合技术制备了纳米Cr2O3／Al2O3，Cr2O3／ZrO2和Cr2O3／MgO复合催化剂．应用BET，XRD，XPS，TPR和TEM等物理化学方法对催化剂的结构和物化性质进行了表征，并考察了该系列催化剂上CO2氧化乙烷脱氢制乙烯的反应性能．结果表明，纳米Cr2O3催化剂上乙烷和CO2的转化率均明显高于常规Cr2O3催化剂，但乙烯的选择性低于常规Cr2O3催化剂；纳米复合催化剂中的复合成分显著影响催化剂的催化性能．其中，10％Cr2O3／MgO纳米复合催化剂在温度为973K时，乙烷转化率和乙烯选择性分别可达到61．54％和94．79％．纳米催化剂表面Cr的还原性以及Cr6＋／Cr3＋比值是影响乙烷转化率和乙烯选择性的重要因素．     

SnO2-Nb2O5/MgAl2O4/α-Al2O3催化环氧乙烷水合制乙二醇

采用水热稳定的MgAl2O4尖晶石对-αAl2O3载体表面进行修饰,采用具有较强亲水性能的SnO2对活性组分Nb2O5进行修饰,制备了SnO2-Nb2O5/MgAl2O4/-αAl2O3催化剂,并用于环氧乙烷水合制乙二醇反应.采用X射线衍射、红外光谱和程序升温脱附研究了Sn/Nb摩尔比对催化剂酸性、环氧乙烷在催化剂表面的吸附状态和吸附强度以及催化剂性能的影响.结果表明,Sn/Nb摩尔比明显影响催化剂的组成和结构;催化剂的结构不同,环氧乙烷在催化剂表面的吸附强度存在明显差别,催化剂的催化性能明显不同.     

Role of SrMoO4 in Sr2MgMoO6 synthesis

Here we investigate the elemental and phase compositions during the solid-state synthesis of the promising SOFC-anode material, Sr₂MgMoO₆, and demonstrate that molybdenum does not notably evaporate under the normal synthesis conditions with temperatures up to 1200 °C due to the formation of SrMoO₄ as an intermediate product at low temperatures, below 600 °C. However, partial decomposition of the Sr₂MgMoO₆ phase becomes evident at the higher temperatures (∼1500 °C). The effect of SrMoO₄ on the electrical conductivity of Sr₂MgMoO₆ is evaluated by preparing a series of Sr₂MgMoO₆ samples with different amounts of additional SrMoO₄. Under the reducing operation conditions of an SOFC anode the insulating SrMoO₄ phase is apparently reduced to the highly conductive SrMoO₃ phase. Percolation takes place with 20-30 wt% of SrMoO₄ in a Sr₂MgMoO₆ matrix, with a notable increase in electrical conductivity after reduction. Conductivity values of 14, 60 and 160 S/cm are determined at 800 °C in 5% H₂/Ar for the Sr₂MgMoO₆ samples with 30, 40 and 50 wt% of added SrMoO₄, respectively.     

Na2SO4辅助水热合成SnO2纳米晶

系统地研究了以SnCl₄·5H₂O为原料，以Na₂SO₄为矿化剂，采用水热法在较低温度下和较短的反应时间内制备结晶良好并均匀分散的SnO₂纳米晶。采用X射线衍射(XRD)、透射电子显微镜(TEM)、红外光谱(IR)等技术对水热反应的晶化过程进行了分析。结果表明：在Na₂SO₄存在的情况下，在120 ℃反应4 h 即可制备得到晶粒细小，分散性能良好的SnO₂纳米晶。XRD衍射峰峰宽随水热温度的升高或反应时间的延长而变窄，结晶性提高。TEM结果表明产物颗粒小、分散性能良好。水热反应温度和反应时间对产物结晶度和粒径有明显的影响。对Na₂SO₄在反应过程中的作用机理进行了分析。     

Synthesis and crystal structure of the palladium oxides NaPd3O4, Na2PdO3 and K3Pd2O4

NaPd₃O₄, Na₂PdO₃ and K₃Pd₂O₄ have been prepared by solid-state reaction of Na₂O₂ or KO₂ and PdO in sealed silica tubes. Crystal structures of the synthesized phases were refined by the Rietveld method from X-ray powder diffraction data. NaPd₃O₄ (space group Pm3¯n, a=5.64979(6) Å, Z=2) is isostructural to NaPt₃O₄. It consists of NaO₈ cubes and PdO₄ squares, corner linked into a three-dimensional framework where the planes of neighboring PdO₄ squares are perpendicular to each other. Na₂PdO₃ (space group C2/c, a=5.3857(1) Å, b=9.3297(1) Å, c=10.8136(2) Å, β=99.437(2)°, Z=8) belongs to the Li₂RuO₃-structure type, being the layered variant of the NaCl structure, where the layers of octahedral interstices filled with Na⁺ and Pd⁴⁺ cations alternate with Na₃ layers along the c-axis. Na₂PdO₃ exhibits a stacking disorder, detected by electron diffraction and Rietveld refinement. K₃Pd₂O₄, prepared for the first time, crystallizes in the orthorhombic space group Cmcm (a=6.1751(6) Å, b=9.1772(12) Å, c=11.3402(12) Å, Z=4). Its structure is composed of planar PdO₄ units connected via common edges to form parallel staggered PdO₂ strips, where potassium atoms are located between them. Magnetic susceptibility measurements of K₃Pd₂O₄ reveal a Curie-Weiss behavior in the temperature range above 80 K.     

磁载WO3－TiO2／SiO2／Fe3O4复合光催化剂的制备及其光催化活性

 用溶胶－凝胶法在表面包覆了SiO2的磁基体Fe3O4上负载TiO2,从而得到了易于磁性固液分离的磁载WO3－TiO2／SiO2／Fe3O4复合光催化剂,并通过IR,XRD,SEM和XPS等测试手段对催化剂进行了表征．研究了磁载WO3－TiO2／SiO2／Fe3O4复合光催化剂对亚甲基蓝溶液脱色的性能,并考察了WO3掺杂量对样品催化活性的影响．结果表明,n（WO3）／n（TiO2）＝0．001时,磁载WO3－TiO2／SiO2／Fe3O4复合光催化剂的催化活性最高,循环使用3次时脱色率仍保持在98％．     

Influence of the support on the state of nickel in the Ni/SiO2, Ni/ZrO2, and Ni/SO4/ZrO2 oxide systems studied by diffuse-reflectance IR spectroscopy

The Ni/SiO₂, Ni/ZrO₂, and Ni/SO₄/ZrO₂ systems were studied by diffuse-reflectance IR spectroscopy using CO as a probe molecule. The Ni/SiO₂ and Ni/ZrO₂ systems are similar in properties, and the state of nickel in the Ni/ZrO₂ system is determined by the specific surface area. In the Ni/SO₄/ZrO₂ system, the surface sulfur compounds affect substantially the state of nickel: Ni^δ+ species with a partial positive charge are formed due to the strong electron-acceptor properties of the sulfur compounds. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 3, pp. 409–413, March, 1998.     

Room temperature carbon monoxide oxidation over Pt/Co2SnO4 and Pt/(Co3O4+SnO2) catalysts

Catalytic activities of Pt/Co2SnO4, Pt/(Co3O4+SnO2), Pt/SnO2, and Pt/Co3O4 catalysts for CO oxidation were investigated by varying CO concentration at room temperature. Reaction rates over Pt/Co2SnO4 and Pt/Co3O4 catalysts were not affected from increase in CO concentration. This revised version was published online in June 2006 with corrections to the Cover Date.     

纯相和镍取代的Co_3O_4尖晶石催化剂用于N_2O直接分解(英文)

A series of NixCo1-xCo2O4(0 ≤ x ≤ 1) spinel catalysts were prepared by the co-precipitation method and used for direct N2O decomposition. The decomposition pathway of the parent precipitates was characterized by thermal analysis. The catalysts were calcined at 500 °C for 3 h and characterized by powder X-ray diffraction, Fourier transform infrared, and N2 adsorption-desorption. Nickel cobaltite spinel was formed in the solid state reaction between NiO and Co3O4. The N2O decomposition measurement revealed significant increase in the activity of Co3O4 spinel oxide catalyst with the partial replacement of Co2+ by Ni2+. The activity of this series of catalysts was controlled by the degree of Co2+ substitution by Ni2+, spinel crystallite size, catalyst surface area, presence of residual K+, and calcination temperature.     

硫中毒对Co3O4/CeO2复合氧化物上炭黑催化燃烧的影响

采用共沉淀法制备了CeO₂,Co₃O₄和一系列Co₃O₄/CeO₂复合氧化物催化剂,在400 ℃下含SO₂的氧化气氛中对催化剂进行了硫中毒处理,通过原位红外光谱、X射线衍射、程序升温脱附和X射线光电子能谱对新鲜和硫中毒的样品进行了表征. 结果表明,所有测试的硫中毒样品上均形成了硫酸盐,CeO₂上累积的硫酸盐明显比Co₃O₄上的多,Co₃O₄/CeO₂复合氧化物在硫中毒过程中形成了硫酸钴和硫酸铈. 对新鲜和硫化样品在NO/O₂气氛下进行了催化炭黑燃烧实验,发现Co₃O₄/CeO₂复合氧化物的活性和抗硫性能优于CeO₂,但抗硫性能低于Co₃O₄.     

Preparation, Structure, and Properties of V2GeO4F2—Chains of VO4F2 Octahedra in the First V(III) Metallate Fluoride

Powder samples of the new oxide fluoride V₂GeO₄F₂ have been obtained by the reaction of appropriate amounts V₂O₃, VF₃, and GeO₂ at 700°C for 18 h in an argon-filled sealed platinum tube. V₂GeO₄F₂ crystallizes in the space group Pnma with a=9.336(1), b=8.898 (1), and c=4.912 (1) Å. The structure has been refined from X-ray powder diffraction data using the Rietveld method (R_int=5.5% and R_p=9.8%). The structure of V₂GeO₄F₂ exhibits close packed layers of the anions with an ordering of O and F. The characteristic building units are discrete GeO₄ tetrahedra with Ge-O distances of 1.75-1.80 Å. The V are coordinated by four O and two F to form VO₄F₂ octahedra connected via two common edges to give zigzag chains. These chains are linked via corners to form a three-dimensional network. The temperature dependence of the magnetic susceptibility of V₂GeO₄F₂ indicates antiferromagnetic correlations.